ARCAT | Free Building Product CAD Details, BIM, Specs and …

 SECTION 05 52 13PIPE AND TUBE RAILING SYSTEMSDisplay hidden notes to specifier. (Don't know how? Click Here) Copyright 2013 - 2020 ARCAT, Inc. - All rights reserved** NOTE TO SPECIFIER ** Leading Edge Safety, LLC; pipe and tube railing systems.This section is based on the products of Leading Edge Safety, LLC, which is located at:1345 Taney St.North Kansas City, MO 64116Toll Free Tel: 888-990-2990Fax: 816-472-0822Email: request info (sales@)Web: [ Click Here ] for additional information.Leading Edge Safety design allows roof safety railing installation under the coping cap, drip edge, gravel stop and even inside most gutter systems. Coping cap sheet metal can be removed during re-roofing without removal of the safety rail system. Unique bracket design allows retrofit installation under an existing coping cap sheet metal, eliminating the cost of new coping cap. Leading Edge Safety uprights are designed to keep workers away from the leading edge while still allowing full access to the roof surface.Leading Edge Safety designs safety railing products that insure OSHA compliance and peace of mind for employees, managers, contractors and building owners that employees and workers are safe while inspecting or working on the roof. Leading Edge Safety safety guardrails eliminate the need for tie-off points and expensive safety equipment.

GENERAL

SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete products not required.

Permanent roof edge protection.

Ballasted guardrails.

Collapsible guardrails.

USM guardrails.

USM guardrails; stainless steel.

Standing seam guardrails.

Wall mount guardrails

Deck mount guardrails.

Roof hatch guardrails.

Skylight guardrails.

Domed skylight fall protection screens.

Warning line stands.

Free-standing ladder to roof access point.

Integrated lightning protection.

RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

Section 05 50 00 - Metal Fabrications.

Section 07 50 00 - Membrane Roofing.

Section 07 70 00 - Roof and Wall Specialties and Accessories.

Section 07 72 26 - Ridge Vents.

REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

American Society for Testing of Materials (ASTM):

ASTM A36 - Standard Specification for Carbon Structural Steel.

ASTM A53 - Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless.

ASTM A269 - Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service.

Occupational Safety and Health Administration (OSHA):

29 CFR 1910.21 - Scope and Definitions

29 CFR 1910.28 - Duty to Have Fall Protection

29 CFR 1910.29 - Walking Working Surfaces

29 CFR-1910.30 - Training Requirements

SUBMITTALS

Submit under provisions of Section 01 30 00 - Administrative Requirements.

Product Data: Manufacturer's data sheets for products and assemblies specified.

Preparation instructions and recommendations.

Storage and handling requirements and recommendations.

Cleaning methods.

Shop Drawings:

Indicate profiles, sizes, connections, size and type of fasteners, accessories.

Show location of rails and guardrails including plans, details of components and anchor details.

Field Verified Measurements: Verify dimensions indicated on Drawings.

Verification Samples: For each finish specified, two samples representing actual colors specified.

DELIVERY, STORAGE, AND HANDLING

Deliver, store and handle materials and products in strict compliance with manufacturer's instructions and recommendations and industry standards.

Store materials in manufacturer's original sealed, labeled packaging until ready for installation and in accordance with manufacturer's instructions. Protect finishes on rails and uprights from damage.

PROJECT CONDITIONS

Maintain environmental conditions, temperature, humidity and ventilation, within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

Field Measurements: Where horizontal rails and uprights are indicated to fit to other construction, check actual dimensions or other construction by accurate field measurements prior to ordering and installation; show recorded measurements on final Shop Drawings.

SEQUENCING AND SCHEDULING

Coordinate fabrication and delivery schedule of handrails with construction progress and sequence to avoid delay of railing installation.

Where field measurements cannot be made without delaying the system fabrication and delivery, obtain guaranteed dimensions in writing by the Contractor and proceed with fabrication of products to not delay fabrication, delivery and installation.

** NOTE TO SPECIFIER ** Delete warranty options not required.

WARRANTY

Warranty: Provide manufacturer's standard one year warranty against defects in materials and manufacturing.

PRODUCTS

MANUFACTURERS

Acceptable Manufacturer: Leading Edge Safety, LLC, which is located at: 1345 Taney St.; North Kansas City, MO 64116; Toll Free Tel: 888-990-2990; Fax: 816-472-0822; Email: request info (sales@); Web:

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

Substitutions: Not permitted.

Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

** NOTE TO SPECIFIER ** Ballasted Guardrail is a fast, easy, and economical way to erect temporary and permanent guardrail systems to keep workers safe while increasing their productivity. Heavy weighted bases prevent tipping and allow configuration to adapt to almost any situation. Weighted Base Guardrails can be used at perimeters, open curbs, skylights, stair openings and anywhere else a leading edge requires fall protection. Meets and exceeds OSHA Standards for guardrails 29 CFR 1910.29. Delete if not required.

BALLASTED GUARDRAILS

Product: Ballasted Guardrail as manufactured by Leading Edge Safety.

Heavy weighted bases ensure stability and can be configured to meet almost any project condition. Meets and exceeds OSHA Standard CFR 29 1910.29 for guardrail systems.

Components:

Uprights: ASTM C1008/1010 steel tube, 1.625 dia x 0.065 inches. Length: 42 inches.

Bases: Class 35 gray iron; galvanized. 23 x 23 inches.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

** NOTE TO SPECIFIER ** Delete spacing and adjustment options not required.

Spacing: 10 ft on center.

Spacing: 8 ft on center.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components, and RAL components.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

** NOTE TO SPECIFIER ** Delete optional toe boards if not required.

Toe Boards: Aluminum. 2 x 4 inches. Thickness: 0.125 inch.

Labels: Applicable safety warnings and manufacturer's contact information.

Uprights:

Top Rail: 42 inches.

Mid Rail: 21 inches.

Weight:

Base: Approximately 99.6 lbs.

Post: Approximately 5 lbs.

Horizontal Rails: Approximately 1 lbs / lineal foot.

** NOTE TO SPECIFIER ** The Collapsible Guardrail is a fast, easy, and economical guardrail system that offers discrete storage when building aesthetics are critical. A single user can erect the system with no pins to get lost. The patent pending integral gravity latch design ensures panels are locked into place when erected. Heavy weighted bases prevent tipping and allow configuration to adapt to almost any situation. Collapsible Guardrails can be used at perimeters, open curbs, skylights, stair openings and anywhere else a leading edge requires fall protection. Delete article if not required.

COLLAPSIBLE GUARDRAIL

Product: USM Collapsible Guardrail as manufactured by Leading Edge Safety. Provides stable stanchion points in combination with steel railings to create safe working areas and collapses when not in use.

Standards: Meets and exceeds OSHA Standards.

Materials:

Panels: 42 x 1.625 x 0.065 inch (1067 x 41 x 1.6 mm) steel tube per ASTM C1008 and ASTM C1010.

Adapter: 1/4 inch (6 mm) steel plate per ASTM A36.

Bases: 23 x 23 inch (584 x 584 mm) Class 35 Gray Iron.

Panel Size: 8 ft (2438 mm).

Panel Size: 6 ft (1829 mm).

Panel Size: 5 ft (1524 mm).

Panel Size: 4 ft (1219 mm).

Panel Weight: 29 lbs (13.2 kg).

Base Weight: 100 lbs (45.4 kg).

Hardware: 3/8-16 x 1 inch (25 mm) Clevis Pin. Zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Finish, Uprights and Rails: Powder Coated Steel or Hot-Dipped Galvanized per ASTM A123.

Finish, Bases: Galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL components

Colors: ________.

Colors: As determined by the Architect from Manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** Guardrail system designed to comply with IBC for 20 lbs per ft. Delete if not required.

USM GUARDRAIL - 20 POUNDS PER FOOT

Product: USM Guardrail as manufactured by Leading Edge Safety.

Permanent full-perimeter fall protection, installed under standard roofing and sheet metal details including coping caps, drip edges, gravel stops and inside most commercial gutters. Powder coated steel colors available to match Kynar sheet metal or other building components in RAL colors. Meets and exceeds OSHA Standards and Building Code requirements.

Components:

Uprights: ASTM A53 schedule 40 pipe, 1.25 inch dia, 1.66 inch O.D. x 0.140 inch wall, welded to an ASTM A36 steel block, 2 x 3 x 3.5 inch, and an ASTM A36 steel plate, 3/16 inch thick bracket with pre-punched holes and slots for permanent structural attachment.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

Spacing: 8 ft on center.

** NOTE TO SPECIFIER ** Delete adjustment options not required.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL colors. Delete color options not required.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** Consult Leading Edge Safety for approved structural attachment fasteners.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: Uprights custom designed per project to OSHA Standards and Building Code requirements.

Corners:

Outside Corner: 20.5 inches o.c.

Inside Corner: 12.5 inches o.c.

** NOTE TO SPECIFIER ** Delete optional toe boards and brackets if not required.

Toe Boards and Brackets: ASTM A1008 CS Type B 18 gauge steel.

Fasteners for Structural Attachment: As recommended by Leading Edge Safety.

For Wood Attachment: RSS Structural Screws by GRK Fasteners. T-Star Washer Head Powerlag by SPAX.

For Concrete Attachment: Caliburn PH Concrete Pan Head Screws by GRK Fasteners.

Others Fasteners: As approved by Leading Edge Safety.

Weight:

Uprights: Approximately 12 lbs.

Horizontal Rails: Approximately 1 lbs per lineal foot.

Corners: Approximately 2 lbs.

Standards: Meets and exceeds OHSA Standard 29 CFR 1910.29, 29 CFR 1926.501, 29 CFR 1926.502, Cal-OSHA 1620, 1621, 3209, 3210, ICC Building Codes, ANSI/ASSE A1264.1, and USACE EM 381-1-1(21.E.01 a-c).

** NOTE TO SPECIFIER ** Guardrail system designed to comply with IBC for 50 lbs per ft. Delete if not required.

USM IBC-50 GUARDRAIL - 50 POUNDS PER FOOT

Product: USM IBC-50 Guardrail as manufactured by Leading Edge Safety.

Permanent full-perimeter fall protection. Installs under standard roofing and sheet metal details including coping caps, drip edges, gravel stops and inside most commercial gutters. Powder coated steel colors available to match Kynar sheet metal or other building components in RAL colors. USM IBC Guardrail meets and exceeds OSHA Standards and Building Code Requirements.

Components:

Uprights: ASTM A513-5-08A DOM Grade 1026 steel tube, 1.625 inch dia x 0.25 inch wall, welded to an ASTM A36 steel block, 2 x 3 x 3.5 inch, and ASTM A572 steel plate, 1/4 inch thick bracket with pre-punched holes and slots for permanent structural attachment.

Adjustable Horizontal Sliding Rails: ASTM A513 DOM Grade 1020 steel tubes, 1.625 inch dia x 0.065 inch wall, and 1.375 inch dia x 0.065 inch wall.

Spacing: 5 feet on center.

** NOTE TO SPECIFIER ** Delete adjustment options not required.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL colors. Delete color options not required.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** Consult Leading Edge Safety for approved structural attachment fasteners.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: Uprights custom designed per project to OSHA Standards and Building Code requirements.

Corners:

Outside Corner: 20.5 inches o.c

Inside Corner: 12.5 inches o.c.

** NOTE TO SPECIFIER ** Delete optional toe boards if not required.

Toe Boards and Brackets: ASTM A1008 CS Type B, 18 gauge steel;

Fasteners for Structural Attachment: As recommended by Leading Edge Safety.

For Wood Attachment: RSS Structural Screws by GRK Fasteners. T-Star Washer Head Powerlag by SPAX

For Concrete Attachment: Caliburn PH Concrete Pan Head Screws by GRK Fasteners.

Other Fasteners: As approved by Leading Edge Safety

Weight:

Uprights: Approximately 12 lbs.

Horizontal Rails: Approximately 1 lbs per lineal foot.

Corners: Approximately 2 lbs.

Standards: Meets and exceeds OHSA Standard 29 CFR 1910.29, 29 CFR 1926.501, 29 CFR 1926.502, Cal-OSHA 1620, 1621, 3209, 3210, ICC Building Codes, ANSI/ASSE A1264.1, and USACE EM 381-1-1(21.E.01 a-c)

NOTE TO SPECIFIER ** The USM Guardrail provides permanent full-perimeter fall protection has a unique design that allows 100 percent water-tight installation under standard roofing and sheet metal details including coping caps, drip edges, gravel stops and even inside most commercial gutters without penetrating the roof membrane. Zero Penetration attachment under standard perimeter edge details allows full access to the entire roof surface, wall flashings and sheet metal. USM Guardrail can be installed prior to roof construction and even left in place during complete roof replacement USM Guardrail meets and exceeds OSHA Standards and Building Code requirements. Delete if not required.

USM GUARDRAIL - STAINLESS STEEL

Product: USM Guardrail-Stainless Steel as manufactured by Leading Edge Safety.

Permanent full-perimeter fall protection, installing under standard roofing and sheet metal details including coping caps, drip edges, gravel stops and inside most commercial gutters. Passivated and electro polished finish for maximum corrosion resistance. USM Guardrail meets and exceeds OSHA Standards and Building Code requirements.

Components:

Uprights: ASTM A312 T304 schedule 40 pipe, 1.25 inch dia, 1.66 inch O.D. x 0.140 inch wall, welded to an ASTM A276 T304 stainless steel bock, 2 x 3 x 3.5 inches, and an ASTM A240 T304 stainless steel plate, 3/16 inch thick bracket with pre-punched holes and slots for permanent structural attachment.

Fixed Horizontal Rails and Adjustable Horizontal Sliding Rails: ASTM A269 T304 stainless steel tube, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

Spacing: 5 feet on center.

** NOTE TO SPECIFIER ** Delete adjustment options not required.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

Finish: ASTM A967.

Color: Chrome appearance.

** NOTE TO SPECIFIER ** Consult Leading Edge Safety for approved structural attachment fasteners.

Hardware: 3/8-16 thread x 1 inch 18-8 stainless steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: Uprights custom designed per project to OSHA Standards and Building Code requirements.

Corners:

Outside Corner: 20.5 inches o.c.

Inside Corner: 12.5 inches o.c.

** NOTE TO SPECIFIER ** Delete optional toe boards if not required

Toe Boards and Brackets: ASTM 240 T304, 16 gauge stainless steel.

Fasteners for Structural Attachment: As recommended by Leading Edge Safety.

For Wood Attachment: PHEINOX RSS Stainless Steel Structural Screws by GRK Fasteners.

For Concrete Attachment: Caliburn PH Concrete Pan Head Screws by GRK Fasteners.

Other Fasteners: As approved by Leading Edge Safety

Weight:

Uprights: Approximately 12 lbs.

Horizontal Rails: Approximately 1 lbs per lineal foot.

Corners: Approximately 2 lbs.

Standards: Meets and exceeds OHSA Standard 29 CFR 1910.29, 29 CFR 1926.501, 29 CFR 1926.502, Cal-OSHA 1620, 1621, 3209, 3210, ICC Building Codes, ANSI/ASSE A1264.1, and USACE EM 381-1-1(21.E.01 a-c)

** NOTE TO SPECIFIER ** The Standing Seam Guardrail System provides permanent full-perimeter fall protection with a unique design that allows for 100 percent water-tight installation. The Standing Seam Guardrail System attaches to the structural metal panels with pre-engineered S-5 clamps ensuring solid and maintenance free installation without penetrating the roof panels. Hot-Dipped Galvanized or Powder coated steel colors available to match Kynar sheet metal or other building components and RAL colors. Standing Seam Guardrail System meets and exceeds OSHA Standards.

STANDING SEAM GUARDRAIL

Product: Standing Seam Guardrail as manufactured by Leading Edge Safety.

Permanent full-perimeter fall protection with 100 percent water-tight installation. The Standing Seam Guardrail System attaches to the structural metal panels with pre-engineered S-5 clamps without penetrating the roof panels. Hot-Dipped Galvanized or Powder coated steel colors available to match Kynar sheet metal or other building components in RAL colors. Standing Seam Guardrail System meets and exceeds OSHA Standards.

Components:

Uprights: ASTM A53 schedule 40 pipe, 1.25 inch dia, 1.66 inch O.D. x 0.140 inch wall, mounted to 12 x 26 x 1/4 inch base plate with pre-punched holes.

Adjustable Horizontal Sliding Rails: ASTM C10081/1010 steel tube, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

Spacing: 8 ft on center.

** NOTE TO SPECIFIER ** Delete adjustment options not required.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL colors. Delete color options not required.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** Consult Leading Edge Safety for approved structural attachment fasteners.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: Uprights custom designed per project to OSHA Standards to meet roof pitch and panel width.

Corners: 90 to 270 degree adjustable hinge corner.

Weight:

Uprights: Approximately 25 lbs.

Horizontal Rails: Approximately 1 lbs per lineal foot.

Corners: Approximately 1 lbs.

Standards: Meets and exceeds OHSA Standard 29 CFR 1910.29, 29 CFR 1926.501, 29 CFR 1926.502, Cal-OSHA 1620, 1621, 3209, 3210, ICC Building Codes, ANSI/ASSE A1264.1, and USACE EM 381-1-1(21.E.01 a-c).

** NOTE TO SPECIFIER ** The Wall Mount Guardrail provides permanent full-perimeter fall protection with a unique design that allows water-tight installation using a dual plate mounting system. The dual plate mounting system allows roof flashing to be installed over the base plate and creates a compression seal around mounting studs when the upright plate is attached. Wall Mount Guardrails are available in powder coat colors to match Kynar sheet metal or other building components and RAL colors or hot-dipped galvanize. Wall Mount Guardrail meets and exceeds OSHA Standards and Building Code requirements. The guardrail system is designed to comply with IBC for 20 lbs per ft. Delete if not required.

WALL MOUNT GUARDRAIL - 20 LBS POUNDS PER FOOT

Product: Wall Mount Guardrail as manufactured by Leading Edge Safety.

Permanent full-perimeter fall protection, allowing direct mounting to interior parapet walls using a dual plate mounting system that assures water-tight installation. Backup plates, target patches, and upright plates creates a compression attachment to prevent water infiltration around mounting studs. Powder coated steel colors available to match Kynar sheet metal or other building components in RAL colors or hot-dipped galvanized. Wall Mount Guardrail meets and exceeds OSHA Standards and Building Code requirements.

Components:

Uprights: ASTM A53 schedule 40 steel pipe, 1.25 inch dia, 1.66 inch O.D. x 0.140 inch wall.

Mounting Bracket: ASTM A36 3/16 inch steel plate with pre-punched holes for mounting stud attachment.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall, and 1.375 inch dia x 0.065 inch wall.

Spacing: 8 ft on center.

** NOTE TO SPECIFIER ** Delete adjustment options not required.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL colors. Delete color options not required.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** Consult Leading Edge Safety for approved structural attachment fasteners.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Uprights custom designed per project to OSHA Standards and IBC code requirements.

Corners:

Outside Corner: 20.5 inches o.c.

Inside Corner: 12.5 inches o.c.

Weight:

Uprights: Approximately 18 lbs.

Horizontal Rails: Approximately 1 lbs per linear foot..

Corners: Approximately 2 lbs.

Standards: Meets and exceeds OHSA Standard 29 CFR 1910.29, 29 CFR 1926.501, 29 CFR 1926.502, Cal-OSHA 1620, 1621, 3209, 3210, ICC Building Codes, ANSI/ASSE A1264.1, and USACE EM 381-1-1(21.E.01 a-c).

** NOTE TO SPECIFIER ** IBC Wall Mount Guardrail provides permanent full-perimeter fall protection with a unique design that allows water-tight installation using a dual plate mounting system. The dual plate mounting system allows roof flashing to be installed over the base plate and creates a compression seal around mounting studs when the upright plate is attached. IBC Wall Mount Guardrail are available in powder coat colors to match Kynar? sheet metal or other building components and RAL colors.Delete article not required.

WALL MOUNT GUARDRAIL !BC 50; 50 LBS PER FOOT

Product: IBC Wall Mount Guardrail, Powder Coated Steel. Permanent full-perimeter fall protection, allowing direct mounting to interior parapet walls using a dual plate mounting system that assures water-tight installation. Backup plates, target patches, and upright plates creates a compression attachment to prevent water infiltration around mounting studs. Powder coated steel colors available to match Kynar sheet metal or other building components and RAL colors.

Standards:

ICC Building Codes: Meets and exceeds 50 lbs per ft (74.4 kg per m).

Meets and exceeds OHSA Standard 29 CFR 1926.501, 1926.502, 1910.29, Cal-OSHA, 1620,1621, 3209, 3210.

ANSI/ASEE A1264.1-2007.

USACE EM 385-1-1 (21.E.01 a-c).

Materials:

Uprights: 1.625 x 0.25 inch (41 x 6 mm) steel tube per ASTM A-513-5-08A DOM Grade 1026.

Mounting Bracket: 3/16 inch (0.28 mm) steel plate per ASTM A36 bracket with pre-punched holes for mounting stud attachment.

Horizontal Rails: 1.625 x 0.065 inch (41 x 1.6 mm) and 1.375 x .065 inch (35 x 1.6 mm) per ASTM A-513 DOM Grade 1020 steel tube adjustable slide rails.

Sizes:

Uprights: Custom designed per project to OSHA Standards and IBC code requirements.

Horizontal Rails: 5 ft (1524 mm) on center; 70 to 43 inch (1778 to 1092), 43 to 29 inch (1092 to 737 mm) adjustable.

Outside Corner: 20.5 inch (521 mm) on center.

Inside Corner: 12.5 inch (218 mm) on center. Inside Corner.

Weight: All weights are approximate.

Uprights: 25 lbs (11.3 kg).

Horizontal Rails: 1 lbs per linear ft (14.6 N per m).

Corners: 2 lbs (0.9 kg).

Hardware: 3/8-16 inch x 1 inch (25 mm) zinc plated steel. Consult LES for approved structural attachment fasteners.

Labels: Applicable safety warnings and manufacturer's contact information.

Finish: Powder coated steel or Hot-Dipped Galvanized to ASTM A123.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL components

Colors: ________.

Colors: As determined by the Architect from Manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** The Deck Mount Guardrail provides permanent full-perimeter fall protection with a unique design that allows pre-fabricated pipe boots to be used to flash penetrations, unlike traditional deck mounted guardrails. Pipe flashings can be placed over the Deck Mount uprights prior to installation of the horizontal railing, a preferred method over field wrapped penetrations. Deck Mount Guardrail are available in powder coat colors to match Kynar sheet metal or other building components and RAL colors or hot-dipped galvanized. Deck Mount Guardrail meets and exceeds OSHA Standards and Building Code requirements. Delete if not required.

DECK MOUNT GUARDRAIL - 20 POUNDS PER FOOT

Product: Deck Mount Guardrail as manufactured by Leading Edge Safety.

Permanent full-perimeter fall protection with a unique design that allows pre-fabricated pipe boots to be used to flash penetrations, unlike traditional deck mount guardrails. Deck Mount uprights allow the use of pre-fabricated pipe flashings that can be installed prior to the horizontal railing. Powder coated steel colors available to match Kynar sheet metal or other building components and RAL colors or hot-dipped galvanized. Wall Mount Guardrail meets and exceeds OSHA Standards and Building Code requirements.

Components:

Uprights: ASTM A53 schedule 40 steel pipe, 1.25 inch dia, 1.66 inch O.D. x 0.140 inch wall.

Mounting Bracket: ASTM A36 3/18 x 6 inch steel plate with pre-punched holes for mounting stud attachment.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall, and 1.375 inch dia x 0.065 inch wall.

Spacing: 8 ft on center.

** NOTE TO SPECIFIER ** Delete adjustment options not required.

Adjustment: 70 to 120 inches.

Adjustment: 43 to 70 inches.

Adjustment: 29 to 42 inches.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL colors. Delete color options not required.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** Consult Leading Edge Safety for approved structural attachment fasteners.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: Uprights: Custom designed per project to OSHA Standards and IBC code requirements.

Weight:

Uprights: Approximately 12 lbs.

Horizontal Rails: Approximately 1 lbs per linear ft.

Corners: Approximately 2 lbs.

Standards: Meets and exceeds OHSA Standard 29 CFR 1910.29, 29 CFR 1926.501, 29 CFR 1926.502, Cal-OSHA 1620, 1621, 3209, 3210, ICC Building Codes, ANSI/ASSE A1264.1, and USACE EM 381-1-1(21.E.01 a-c)

** NOTE TO SPECIFIER ** The IBC Wall Mount Guardrail provides permanent full-perimeter fall protection allowing water-tight installation using a dual plate mounting system. Roof flashing can be installed over the base plate and creates a compression seal around mounting studs when the upright plate is attached. Available in powder coat colors to match Kynar sheet metal or other building components and RAL colors. Delete article not required.

DECK MOUNT GUARDRAIL !BC 50; 50 POUNDS PER FOOT

Product: IBC Wall Mount Guardrail-Powder Coated Steel. Permanent full-perimeter fall protection, allowing direct mounting to interior parapet walls using a dual plate mounting system that assures water-tight installation. Backup plates, target patches, and upright plates creates a compression attachment to prevent water infiltration around mounting studs. Powder coated steel colors available to match Kynar sheet metal or other building components and RAL colors.

Standards:

ICC Building Codes: Meets and exceeds 50 lb/ft requirements.

Meets and exceeds OHSA Standard 29 CFR 1926.501, 1926.502, 1910.29, Cal-OSHA, 1620, 1621, 3209, 3210.

ICC Building Codes, ANSI/ASEE A1264.1-2007.

USACE EM 385-1-1 (21.E.01 a-c).

Materials:

Uprights: 1.625 x 0.25 inch (41 x 6 mm) steel tube per ASTM A-513-5-08A DOM Grade 1026.

Mounting Bracket: 3/16 inch (5 mm) steel plate per ASTM A36 bracket with pre-punched holes for mounting stud attachment.

Horizontal Rails: 1.625 x 0.065 inch (41 x 1.6 mm) and 1.375 x .065 inch (35 x 1.6 mm) per ASTM A-513 DOM Grade 1020 steel tube adjustable slide rails.

Sizes:

Uprights: Custom designed per project to OSHA Standards and IBC code requirements.

Horizontal Rails: 5 ft (1524 mm) on center; 70 to 43 inch (1778 to 1092 mm), 43 to 29 inch (1092 to 737 mm) adjustable.

Outside Corner: 20.5 inch (521 mm) on center.

Inside Corner: 12.5 inch (318 mm) on center. Inside Corner.

Weight: All weights are approximate.

Uprights: 25 lbs (11.3 kg).

Horizontal Rails: 1 lbs per linear ft (14.6 N per m).

Corners: 2 lbs (0.9 kg).

Hardware: 3/8-16 inch x 1 inch (25 mm) zinc plated steel. Consult LES for approved structural attachment fasteners.

Labels: Applicable safety warnings and manufacturer's contact information.

Finish: Powder coated steel or Hot-Dipped Galvanized to ASTM A123.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components and RAL components

Colors: ________.

Colors: As determined by the Architect from Manufacturer's range.

Colors: As scheduled on the Drawings.

** NOTE TO SPECIFIER ** The Roof Hatch Guardrail provides permanent full-perimeter fall protection and improved egress and ingress for all roof hatches. Roof Hatch Guardrail meets and exceeds numerous Standards and requirements for floor openings and walking/working surfaces. Zero Penetration attachment will not damage roof flashings, prevents moisture from entering the building, and will not void the roof warranty. Each unit features patented GrabSafe handholds, providing 3-point control throughout egress and ingress. Guardrail extensions create a landing area to ensure safe operation of the self-closing gate while standing on the walking surface, not the ladder. Delete if not required.

ROOF HATCH GUARDRAIL

Product: Roof Hatch Guardrail as manufactured by Leading Edge Safety.

Patented GrabSafe horizontal hand-holds and self-closing gate provides safe egress and ingress through roof hatches in addition to providing protection against accidental falls through the roof opening while the roof hatch is open. GrabSafe horizontal hand-holds act as an extension of the ladder for more comfortable and safe climbing and allows pass-through to the roof surface. Guardrail extensions create a landing area for safe transition to the roof surface before operating the gate. Self-closing gate ensures full perimeter protection.

Components:

Uprights: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall welded to an ASTM A1011 CS Type B, 10 gauge steel bracket with 3/8 inch pre-punched slots for thru-bolt attachment.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

GrabSafe: ASTM A513, 1 inch dia x 10.5 inch long steel tube welded to an ASTM A1011 CS Type B 10 gauge steel bracket.

Self-Closing Gate: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall and ASTM A1008 CS Type B, 16 gauge steel plate.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components, and RAL components.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

** NOTE TO SPECIFIER ** Delete sizes not required.

Size: 30 inches x 36 to 54 inches.

Size: 30 inches x 54 to 96 inches.

Size: 36 inches by 36 to 54 inches.

Size: 48 inches by 48 to 70 inches

Size: ________.

Size: As determined by the Architect.

Weight: Approximately 110 lbs.

Standards: Meets and exceeds OHSA standard CFR 29 1910.29, , Cal-OSHA 3209, 3210, ANSI/ASSE A1264.1, ANSI/ASSE A14.3 section 5.3.4.3 and US Army Corps of Engineer Requirement EM 385-1-1.

** NOTE TO SPECIFIER ** The Skylight Guardrail provides permanent 4-sided fall protection around virtually any skylight or smoke vent. Skylight Guardrail meets and exceeds numerous Standards and requirements for floor openings and walking/working surfaces. "Zero Penetration" attachment conceals fasteners to prevents moisture from entering the building, and will not void the roof warranty. Custom designed to fit virtually any size skylight including acrylic skylights, structural skylights and smoke vents. Skylight guardrails provide high-visibility even on snow covered roofs. Delete if not required.

SKYLIGHT GUARDRAIL

Product: Skylight Guardrail as manufactured by Leading Edge Safety.

Four sided permanent protection against accidental falls through acrylic dome skylights, structural skylights, and smoke vent roof openings. Custom designed to fit size of acrylic dome skylight, structural skylight, or smoke vent.

Components:

Uprights: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall welded to ASTM A36 steel block, 2 x 3 x 3.5 inch and an ASTM A36, 1/4 inch thick bracket with 3/8 inch pre-punched slots for attachment.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components, and RAL components.

Colors: ________.

Colors: High-visibility Safety Yellow.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

** NOTE TO SPECIFIER ** The Domed Skylight Fall Protection Screen provides permanent fall protection at skylights and does not penetrate the roof membrane. "Zero Penetration" attachment will not damage roof flashings, prevents moisture from entering the building, and will not void the roof warranty. Galvanized screens install quickly and easily to ensure long-term performance, safety and compliance. Domed Skylight Fall Protection Screen meets and exceeds numerous Standards and requirements for skylight openings and ensures OSHA compliance. Delete if not required.

DOMED SKYLIGHT FALL PROTECTION SCREENS

Product: Fall protection for skylight units. Galvanized screens and aluminum mounting rails ensure long-term performance, safety, and compliance.

Components:

Screen: 3 x 4 inch welded wire mesh; 0.195 inch.

Extrusion: Outdoor PVC, extruded.

Retaining Clips: Stainless Steel.

Finish: Galvanized ASTM A123.

Hardware: Galvanized 3/4 inch No. 12 hex washer head self-drilling screws.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: 8 feet wide x unlimited lengths.

Weight: 1.5 lbs per sq ft.

Standards: Meets and exceeds OHSA standard CFR 29 1926.501, CFR 291910.29, Cal-OSHA 3212(e), ANSI/ASSE A1264.1-2007 section 3.4.

** NOTE TO SPECIFIER ** The Permanent Warning Line is a fast, easy, and economical way to erect warning lines for work areas to alert workers of dangerous conditions and help prevent accidents. Heavy weighted bases prevent tipping in high winds, while steel cables and permanent warning flags ensure barrier visibility. Permanent warning flags eliminate the need for frequent inspections to replace torn or worn out flagging. Meets and exceeds OSHA Standards for warning lines 29 CFR 1926.502(f) and 1910.29. Delete if not required.

WARNING LINE STANDS

Product: Permanent Warning Line as manufactured by Leading Edge Safety.

Heavy weighted bases provide during high winds. Steel cable and warning flags provide visibility. Meets and exceeds OSHA Standard CFR 29 1926.502(f) and 1910.29 for warning line systems.

Components:

Uprights: Steel tube, 1.625 inch dia x 0.065 inch wall. Length: 42 inches.

Bases: Steel plate. 23 x 23 inches. Thickness: 1 inch.

Nylon Coated Galvanized Steel Cable: 5/32 inch; 7x19.

Warning Flags: 4 x 6 inches triangular shape aluminum with folding tabs.

Finish: Powder coated steel.

Colors: Safety Yellow and colors to match Kynar sheet metal, building components and RAL colors.

Hardware: Stainless steel clamps.

Labels: Applicable safety warnings and manufacturer's contact information.

Weight: 99.6 lbs.

** NOTE TO SPECIFIER ** The Ladder to Roof Access Point provides permanent fall protection, a controlled access zone, and safer step-on and step-off for both temporary and fixed ladder points. Ladder to Roof Access Point meets and exceeds Standards and requirements for controlled access zones. Delete if not required.

FREE-STANDING LADDER TO ROOF ACCESS POINT

Free-Standing Ladder to Roof Access Point as manufactured by Leading Edge Safety. Permanent fall protection, a controlled access zone, and safe step-on and step-off for both temporary and fixed ladder points.

Components:

Uprights: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall.

Bases: Class 35 gray iron. Galvanized. 23 x 23 inches.

Adjustable Horizontal Sliding Rails: ASTM C1008/1010, 1.625 inch dia x 0.065 inch wall and 1.375 inch dia x 0.065 inch wall.

Self-Closing Gate: ASTM C1008/1010 steel tube, 1.625 inch dia x 0.065 inch wall and ASTM A1008 CS Type B, 16 gauge steel plate.

** NOTE TO SPECIFIER ** Delete finish option not required.

Finish: Powder coat.

Finish: Hot-dipped galvanized.

** NOTE TO SPECIFIER ** Numerous colors to match Kynar sheet metal, building components, and RAL components.

Colors: ________.

Colors: As determined by the Architect from manufacturer's range.

Colors: As scheduled on the Drawings.

Hardware: 3/8-16 thread x 1 inch long zinc plated steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Size:

Width: 5 feet-6 inches

Adjustable Height: 4 feet-8 inches to 6 feet-11 inches

Weight: 230 lbs.

** NOTE TO SPECIFIER ** Integrated Lightning Protection (ILP) is designed for use with all Leading Edge Safety Permanent Guardrail Systems. ILP installs quickly and easily, and the complete system can be left in place during future roof projects without compromising worker safety or your buildings lightning protection. The aluminum top rail and cast aluminum post cap and rail caps replace unsightly cables cluttering the roof perimeter. Meets and exceeds IBC 2006 requirements, OSHA Standard 29 CFR 1910.29 and is UL Listed. Delete if not required.

INTEGRATED LIGHTNING PROTECTION

Product: Integrated Lightning Protection as manufactured by Leading Edge Safety.

Both guardrail protection for workers and lightning protection for the building. Meets and exceed IBC 2006 requirements, OSHA Standard 29 CFR 1910.29 and is eligible for lightning protection UL Master Label.

Components:

Post Cap: Cast 356.1 Aluminum.

Rail Connector: Cast 356.1 Aluminum.

Corner Connector: Cast 356.1 Aluminum.

Horizontal Rail: ASTM B429 6061-T6 Schedule 80 aluminum. 1.66 inch dia x 0.191 inch wall.

Finish: Mill finish. Top Rail can be powder coated.

Colors: Numerous colors to match Kynar sheet metal, building components and RAL components.

Hardware: 3/8-16 x 1-1/2 inches hex head bolt, full threads 18-8 stainless steel. 3/8 inch flat washer 18-8 stainless steel.

Labels: Applicable safety warnings and manufacturer's contact information.

Sizes: Caps: 5.75 x 1.75 inches ID.

End Connectors: 4.75 x 1.70 inches ID.

Corner Connectors: 4.75 x 1.10 inches ID.

Horizontal Rails: 8 feet-0 inches o.c. Field cut to fit.

Weight:

Caps: 0.75 lb.

End Connectors: 0.825 lb.

Corner Connectors: 0.4626 lb.

Horizontal Rails: Approximately 1.037 lbs per lineal foot.

EXECUTION

EXAMINATION AND PREPARATION

Inspect and prepare substrates and nailers using the methods recommended by the manufacturer for achieving best result for the substrates under project conditions. Verify that nailers and other structural components of the building are securely fastened and capable of withstanding loads applied by the guardrail system.

Do not proceed with installation until substrates and nailers have been prepared using the methods recommended by the manufacturer and deviations from manufacturer's recommended tolerances are corrected. Commencement of installation constitutes acceptance of conditions.

If preparation is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions.

INSTALLATION

Install in accordance with manufacturer's instructions including the following.

** NOTE TO SPECIFIER ** Permanent roof edge protection. Delete if not required.

Permanent Roof Edge Protection:

Set uprights, horizontal rails and corners accurately in location, alignment and elevation, measured from established lines and levels and per installation drawings.

Install fasteners as recommended by manufacturer in holes provided on the upright bracket.

Inspect final installation and test for capacity in accordance with manufacturer's recommendations.

** NOTE TO SPECIFIER ** Ballasted Guardrails. Delete if not required.

Ballasted Guardrails: Weighted bases and uprights shall be placed around the perimeter of the roof as indicated at required distances or other areas for fall protection or controlled access. Horizontal railings attach to uprights using 7/32 inch hex key bolts.

** NOTE TO SPECIFIER **USM Guardrail, painted, hot-dipped galvanized and stainless steel products. Delete if not required.

USM Guardrail shall be installed on roof edge perimeters without penetrating the roof membrane and mounted under the outside perimeter sheet metal as detailed.

** NOTE TO SPECIFIER ** Standing Seam Guardrail System. Delete if not required.

Standing Seam Guardrail System shall be installed on roof edge perimeters without penetrating the roof panels.

** NOTE TO SPECIFIER ** Wall Mount Guardrail. Delete if not required.

Wall Mount Guardrail shall provide water-tight installation through wall flashings on parapet walls with the use of backup plates, target patches and wall mount brackets. Target patches shall be field fabricated to fit around backup plate mounting studs and provide roof manufacturers recommended seam width around perimeter of target patch. Mounting studs shall be sealed behind target patch with non-curing butyl or manufacturers recommended sealant.

** NOTE TO SPECIFIER ** Roof Hatch Guardrail. Delete if not required.

Roof Hatch Guardrail shall be installed mounting to the vertical cap flashing of the roof hatch without penetrating the roof membrane. Roof hatches without vertical cap flashing thru-bolt the side of the roof hatch and require counter-flashing to conceal fasteners by others.

** NOTE TO SPECIFIER ** Skylight Guardrail. Delete if not required.

Skylight Guardrail shall be installed under acrylic dome flashings with concealed fasteners. Skylight guardrail shall be side mounted to structural skylights and smoke vents.

** NOTE TO SPECIFIER ** Domed Skylight Screens. Delete if not required.

Domed Skylight Screens shall be installed on acrylic dome skylight units. Standard installation requires mounting to the skylight frame without penetrating the roof membrane.

** NOTE TO SPECIFIER ** Delete mounting option not required.

Standard mount.

Reverse mount.

** NOTE TO SPECIFIER ** Permanent Warning Line. Delete if not required.

Weighted bases and uprights shall be placed around the perimeter of the roof at required distances or other areas requiring controlled work zones. Steel cable shall be connected to the upright using quick-connect tabs. Aluminum flags with fold over tabs shall be placed at required intervals.

** NOTE TO SPECIFIER ** Free-Standing Ladder to Roof Access Point. Delete if not required.

Free-Standing Ladder to Roof Access Point shall be installed ladder points without penetrating the roof membrane and mounted under the outside perimeter sheet metal detail.

** NOTE TO SPECIFIER ** Integrated Lightning Protection. Delete if not required.

Integrated Lightning Protection shall be installed with guardrails around the building perimeter for lightning protection and fall protection. Aluminum Post Caps shall be added to the guardrail uprights, an aluminum pipe top rail shall be installed with Rail Connectors. The system shall be grounded every 100 feet or less as required for the lightning protection system. Ground cables shall be provided by the installing contractor.

PROTECTION

Protect installed products until completion of project.

Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download