Configuring the Linksys WRV54G Wireless Router
Configuring the Linksys WRV54G Wireless Router
|Author |Revision |Date |Notes |
|John Cobb |Genesis |08-21-2006 |Router Software Version 2.39.2 |
|John Cobb |Minor |08-22-2006 |Router Password / Screen shots |
| | | | |
| | | | |
Topics Covered
• Firmware Upgrades
• Basic Setup & Configuration
• Basic Wireless Settings
• Wireless Security Configuration
• Router Configuration Backup/Restore
• Router Password Aministration
Step 1:
Login to the router with the following IP Address:
Note the Firmware Version in the top right corner. It should not be the same as the one shown [2.39.2].
[pic]
Step 2:
Click on the Administration tab followed by clicking the Firmware Upgrade tab. Browse to the firmware file downloaded from the website; then click the upgrade button. This will begin the upgrade progress.
[pic]
Step 3:
After the upgrade is complete log back into the router with the address. The password should go back to the factory default of (Username: admin Password: admin) all lower case. Once logged in, notice the new firmware version at the top right portion of the screen.
1. Set the router to Automatic Configuration – DHCP
2. Set Host Name & Domain Name to
3. Click the Save Settings link at the bottom of the screen to save.
[pic]
Step 4:
Click the Wireless | Basic Wireless Settings sub tab and set the following fields.
Wireless Network Mode: Mixed
Wireless Network Name (SSID): matscanner
Wireless Channel: 6 – 2.437 GHz
Wireless SSID Broadcast: Enabled
Click Save Settings link at bottom of page to save.
[pic]
Step 5:
Click the Wireless | Wireless Security sub tab.
Security Mode: WPA Pre-Shared Key
WPA Algorithms: TKIP
WPA Shared Key: 1qaz9ijn!
Key Renewal Timeout 900 seconds
[pic]
Step 6:
Click on the Administration | Config Management tab then click Download Router Configuration File button. Save this file somewhere safe in the event the router looses its settings to power failure or future firmware upgrades.
[DO NOT PERFORM FOLLOWING UNLESS INSTRUCTED]
To restore the settings, simply click browse to find the configuration file, then click Load.
[pic]
Step 6:
Now, reset the administration password to the router by clicking Administration | Management.
Username: matscanner
Password: 1qaz9ijn!
[pic]
Step 7: (Optional)
Once you know the router is working properly you can configure MAC filtering. The preferred method is to click Select MAC Address From Networked Computers. Systematically turn off each device and click the refresh button. This will allow you to select each device’s MAC address and Permit access to it. It is also recommended that you note the Serial Number of each gun the MAC address is associated with.
[pic]
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- 1 configuring your broadband vpn router
- stealing passwords with wireshark
- how to setup internet connection sharing on windows xp
- configuring the linksys wrv54g wireless router
- rt31p2 wrt54gp2 alternate unlock short method
- encryption privacy authentication project report
- how to find your ssid number furman university
- homework 1
- configuring an access point
Related searches
- 192.168.1.1 wireless router configuration
- 192 168 1 1 wireless router configuration
- 192 168 0 1 wireless router configuration
- 192 168 0 1 wireless router setup
- 192 168 1 1 wireless router setup
- 192 168 1 1 wireless linksys router setup
- how to access linksys router admin page
- 192 168 1 1 linksys router password
- d link wireless router setup password
- 192 168 1 1 asus wireless router setup
- netgear wireless router admin page
- linksys router password