147-3901 DODGE 5.7L-6.1L HEMI V8 HBK installation - Summit Racing Equipment
Automotive Racing Products
1863 Eastman Avenue
Ventura, Ca 93003
Tel: (805) 339-2200
Fax: (805) 650-0742
arp-
INSTALLATION METHOD FOR P RO SERIES HEAD BOLT KITS
Part Number:
1.
2.
3.
4.
5.
6.
7.
147-3901
Application: Dodge 5.7L & 6.1L Hemi V8
To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if
necessary with ARP Thread Chaser, part number 912-0007 (M12 X 1.5).
Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit,
length and dimension.
Position the chamfered side of the washer on the bolt so it faces the bolt head. This is done to clear the radius on the
under head of the bolt. Not e: Improper installation of the washer will cause premature bolt failure.
If the cylinder head bolts protrude into a water jacket, lubricate the threads of the bolts with ARP THREAD SEALER.
If the cylinder head bolts protrude into a blind hole, lubricate the threads of the bolts with ARP ULTRA-TORQUE
FASTENER ASSEMBLY LUBRICANT.
Install the cylinder head(s) and check for binding or misalignment.
Lubricate the under head of the bolt and the washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY
LUBRICANT. Then install the bolts into the cylinder head and tighten them hand tight. ARP recommends using the
ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to motor
oil. This is due to higher friction on the bolts as well as inconsistencies in the clamping force of the fasteners
when motor oil or other low quality lubricants are used.
PR EL OA D ( T OR QU E) RE C OM ME N D ATI ONS
8. Following the manufacturers recommended torque sequence tighten the bolts in three equal steps to
with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
100
ft lbs
Note : ARP Ultra-Torque Fastener Assembly Lubricant has been specifically designed to reduce tension preload scatter and
eliminate the need to cycle high performance engine fasteners before final installation. ARP Ultra-Torque far surpasses all
requirements offered by previous ARP lubricants in terms of fastener preload repeatability and performance lubricating
properties. For more information on ARP Ultra-Torque visit our website at arp- or call 1 800-826-3045.
Automotive Racing Products
1863 Eastman Avenue
Ventura, Ca 93003
Tel: (805) 339-2200
Fax: (805) 650-0742
arp-
INSTALLATION METHOD FOR P RO SERIES HEAD BOLT KITS
Part Number:
1.
2.
3.
4.
5.
6.
7.
147-3901
Application: Dodge 5.7L & 6.1L Hemi V8
To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if
necessary with ARP Thread Chaser, part number 912-0007 (M12 X 1.5).
Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit,
length and dimension.
Position the chamfered side of the washer on the bolt so it faces the bolt head. This is done to clear the radius on the
under head of the bolt. Not e: Improper installation of the washer will cause premature bolt failure.
If the cylinder head bolts protrude into a water jacket, lubricate the threads of the bolts with ARP THREAD SEALER.
If the cylinder head bolts protrude into a blind hole, lubricate the threads of the bolts with ARP ULTRA-TORQUE
FASTENER ASSEMBLY LUBRICANT.
Install the cylinder head(s) and check for binding or misalignment.
Lubricate the under head of the bolt and the washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY
LUBRICANT. Then install the bolts into the cylinder head and tighten them hand tight. ARP recommends using the
ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to motor
oil. This is due to higher friction on the bolts as well as inconsistencies in the clamping force of the fasteners
when motor oil or other low quality lubricants are used.
PR EL OA D ( T OR QU E) RE C OM ME N D ATI ONS
8. Following the manufacturers recommended torque sequence tighten the bolts in three equal steps to
with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT.
100
ft lbs
Note : ARP Ultra-Torque Fastener Assembly Lubricant has been specifically designed to reduce tension preload scatter and
eliminate the need to cycle high performance engine fasteners before final installation. ARP Ultra-Torque far surpasses all
requirements offered by previous ARP lubricants in terms of fastener preload repeatability and performance lubricating
properties. For more information on ARP Ultra-Torque visit our website at arp- or call 1 800-826-3045.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- 5 7l 6 1l 6 4l volume 1
- hemi single page layout melling
- dodge challenger
- new for the chrysler gen iii hemi 5 7 6 1 2003 08 non vvt hp x silver
- 244 4300 chrysler 5 7l 6 1l hemi hsk installation
- 5 7l 6 4l chrysler hemi phaser limiter kit 5761
- ram hemi 5 7l v8 ram 1500 express laramie harrop
- 147 2501 chrysler 5 7l 6 4l hemi bbk summit racing equipment
- announces new high performance hemi oil pump chrysler 5 7l 6 4l engines
- edelbrock performer rpm cylinder heads chrysler gen iii hemi 5 7 6 1
Related searches
- translate the graph of f x |3x| 5 down 6 units
- translate the graph of f x 3x 5 down 6 units
- 5 and 6 grade free printable worksheets
- 5 over 6 divided by 2
- 6 5 vs 6 8 ballistics chart
- gmc 6 2 liter v8 horsepower
- 5 7l v8 horsepower
- summit racing equipment location
- summit racing equipment store locations
- summit racing piston rings
- summit racing parts
- 5 foot 6 inches conversion