CHAPTER 1



Instructor ManualAUTOMOTIVE BRAKES, STEERING, AND SUSPENSIONGeneral Motors Fundamentals SeriesJames HaldermanJeffrey Rehkopf, Editor2012 NATEF/STC Correlation Chart2Chapter Questions Answer Key13GM ASEP Chassis Systems NATEF Correlation ChartMLR- Maintenance & Light Repair tasksAST- Auto Service Technology (Includes MLR) tasksMAST- Master Auto Service Technology (Includes MLR and AST) tasksChapter – Indicates where the task is discussedSTC Course # - Suggested GM STC course related to the listed taskTaskPriorityMLRASTMASTChapterSTC Course #SUSPENSION AND STEERING (A4)General: Suspension and Steering Systems1.Research applicable vehicle and service information, vehicle service history, service precautions, and technical service bulletins.P-1Fund10041.12W13044.13T12.Identify and interpret suspension and steering system concerns; determine necessary action.P-123, 24, 2713041.15WSteering Systems Diagnosis and Repair1.Disable and enable supplemental restraint system (SRS).P-1Fund13041.15W2.Remove and replace steering wheel; center/time supplemental restraint system (SRS) coil (clock spring).P-12613041.15W3.Diagnose steering column noises, looseness, and binding concerns (including tilt mechanisms); determine necessary action.P-22613041.15W4.Diagnose power steering gear (non-rack and pinion) binding, uneven turning effort, looseness, hard steering, and noise concerns; determine necessary action.P-22613041.15WTaskPriorityMLRASTMASTChapterSTC Course #5.Diagnose power steering gear (rack and pinion) binding, uneven turning effort, looseness, hard steering, and noise concerns; determine necessary action.P-22613041.15W6.Inspect steering shaft universal-joint(s), flexible coupling(s), collapsible column, lock cylinder mechanism, and steering wheel; perform necessary action.P-22613041.15W03510.08W7.Remove and replace rack and pinion steering gear; inspect mounting bushings and brackets.P-22813041.15W8.Inspect rack and pinion steering gear inner tie rod ends (sockets) and bellows boots; replace as needed.P-2Inspect only(P-1)2713041.15W03510.08W9.Determine proper power steering fluid type; inspect fluid level and condition.P-12813041.15W00510.01-R203510.08W10.Flush, fill, and bleed power steering system.P-22813041.15W11.Inspect for power steering fluid leakage; determine necessary action.P-12813041.15W12.Remove, inspect, replace, and adjust power steering pump drive belt.P-12813041.15W13.Remove and reinstall power steering pump.P-22813041.15W14.Remove and reinstall press fit power steering pump pulley; check pulley and belt alignment.P-2Check/adjust PS belt)(P-1)2813041.15W03510.08W15.Inspect and replace power steering hoses and fittings.P-2 2803510.08W16.Replace power steering pump filter(s).P-1(P-2)TaskPriorityMLRASTMASTChapterSTC Course #17.Inspect and replace pitman arm, relay (centerlink/intermediate) rod, idler arm and mountings, and steering linkage damper.P-2(P-1)2713041.15W18.Inspect, replace, and adjust tie rod ends (sockets), tie rod sleeves, and clamps.P-12713041.15W19.Test and diagnose components of electronically-controlled steering systems using a scantool; determine necessary action.P-3Inspect electric power steering only2813041.15W20.Identify hybrid vehicle power steering system electrical circuits and safety precautions.P-22818070.01W-R218440.01W18440.05W-R2Suspension Systems Diagnosis and Repair1.Diagnose short and long arm suspension system noises, body sway, and uneven ride height concerns; determine necessary action.P-123, 2413041.15W2.Diagnose strut suspension system noises, body sway, and uneven ride height concerns; determine necessary action.P-123, 2413041.15W3.Inspect, remove and install upper and lower control arms, bushings, shafts, and rebound bumpers.P-3Inspect and replace rebound and jounce bumper only(P-1)2313041.15W4.Inspect, remove and install strut rods and bushings.P-32313041.15W5.Inspect, remove and install upper and/or lower ball joints (with or without wear indicators).P-2Inspect only(P-1)2313041.15W6.Inspect, remove and install steering knuckle assemblies.P-323TaskPriorityMLRASTMASTChapterSTC Course #7.Inspect, remove and install short and long arm suspension system coil springs and spring insulators.P-3Inspect only(P-1)2313041.15W8.Inspect, remove and install torsion bars and mounts.P-3Inspect only(P-1)2313041.15W9.Inspect, remove and install front stabilizer bar (sway bar) bushings, brackets, and links.P-3Inspect only(P-1)2313041.15W10.Inspect, remove and install strut cartridge or assembly, strut coil spring, insulators (silencers), and upper strut bearing mount.P-3Inspect only(P-1)2313041.15W11.Inspect, remove and install track bar, strut rods/radius arms, and related mounts and bushings.P-3Inspect only(P-1)2412.Inspect rear suspension system leaf spring(s), bushings, center pins/bolts, and mounts.P-12413.Inspect electric power-assisted steering.P-32813041.15W13041.13T1Related Suspension and Steering Service1.Inspect, remove, and replace shock absorbers; inspect mounts and bushings.P-123, 2403510.05W2.Remove, inspect, and service or replace front and rear wheel bearings.P-12103510.05W3.Describe the function of the power steering pressure switch.P-328Wheel Alignment Diagnosis, Adjustment, and Repair1.Diagnose vehicle wander, drift, pull, hard steering, bump steer, memory steer, torque steer, and steering return concerns; determine necessary action.P-129, 3013044.11W-R203510.10W2.Perform pre-alignment inspection and measure vehicle ride height; perform necessary action.P-13013044.11W-R2TaskPriorityMLRASTMASTChapterSTC Course #3.Prepare vehicle for wheel alignment on alignment machine; perform four-wheel alignment by checking and adjusting front and rear wheel caster, camber; and toe as required; center steering wheel.P-13013044.11W-R203510.10W4.Check toe-out-on-turns (turning radius); determine necessary action.P-23013044.11W-R203510.10W5.Check SAI (steering axis inclination) and included angle; determine necessary action.P-23013044.11W-R203510.10W6.Check rear wheel thrust angle; determine necessary action.P-13013044.11W-R27.Check for front wheel setback; determine necessary action.P-23013044.11W-R28.Check front and/or rear cradle (subframe) alignment; determine necessary action.P-33013044.11W-R2Wheels and Tires Diagnosis and Repair1.Inspect tire condition; identify tire wear patterns; check for correct tire size and application (load and speed ratings) and adjust air pressure; determine necessary action.P-118, 2003510.01W2.Diagnose wheel/tire vibration, shimmy, and noise; determine necessary action.P-22013042.11W-R250240.16T13.Rotate tires according to manufacturer’s recommendations.P-12003510.01W4.Measure wheel, tire, axle flange, and hub runout; determine necessary action.P-21813042.11W-R25.Diagnose tire pull problems; determine necessary action.P-21813042.11W-R26.Dismount, inspect, and remount tire on wheel; balance wheel and tire assembly (static and dynamic).P-12003510.01W7.Dismount, inspect, and remount tire on wheel equipped with tire pressure monitoring system sensor.P-22003510.01W8.Inspect tire and wheel assembly for air loss; perform necessary action.P-12003510.01W9.Repair tire using internal patch.P-12003510.01W10.Identify and test tire pressure monitoring system (indirect and direct) for operation; calibrate system; verify operation of instrument panel lamps.P-21913044.12T211.Demonstrate knowledge of steps required to remove and replace sensors in a tire pressure monitoring system.P-1(P-2)1913044.12T2TaskPriorityMLRASTMASTChapterSTC Course #BRAKES (A5)General: Brake Systems Diagnosis1.Identify and interpret brake system concerns; determine necessary action.P-13, 8, 10, 11, 1515045.11W12.Research applicable vehicle and service information, vehicle service history, service precautions, and technical service bulletins.P-1110041.12W3.Describe procedure for performing a road test to check brake system operation; including an anti-lock brake system (ABS).P-18, 10. 15Hydraulic System Diagnosis and Repair1.Diagnose pressure concerns in the brake system using hydraulic principles (Pascal’s Law).P-12, 315045.11W12.Measure brake pedal height, travel, and free play (as applicable); determine necessary action.P-1315045.11W13.Check master cylinder for internal/external leaks and proper operation; determine necessary action.P-1315045.11W14.Remove, bench bleed, and reinstall master cylinder.P-1315045.11W15.Diagnose poor stopping, pulling or dragging concerns caused by malfunctions in the hydraulic system; determine necessary action.P-33, 415045.11W16.Inspect brake lines, flexible hoses, and fittings for leaks, dents, kinks, rust, cracks, bulging, and wear; check for loose fittings and supports; determine necessary action.P-1515045.11W1TaskPriorityMLRASTMASTChapterSTC Course #7.Replace brake lines, hoses, fittings, and supports.P-2515045.11W18.Fabricate brake lines using proper material and flaring procedures (double flare and ISO types).P-2515045.11W19.Select, handle, store, and fill brake fluids to proper level.P-1515045.11W100510.01-R210.Inspect, test, and/or replace components of brake warning light system.P-3415045.11W111.Identify components of brake warning light system.P-2(P-3)415045.11W112.Bleed and/or flush brake system.P-1615045.11W113.Test brake fluid for contamination.P-1515045.11W100510.01-R2Drum Brake Diagnosis and Repair1.Diagnose poor stopping, noise, vibration, pulling, grabbing, dragging or pedal pulsation concerns; determine necessary action.P-17, 815045.11W12.Remove, clean, inspect, and measure brake drum diameter; determine necessary action.P-11215045.11W150240.34T100510.10W3.Refinish brake drum and measure final drum diameter; compare with specifications.P-11215045.11W14.Remove, clean, and inspect brake shoes, springs, pins, clips, levers, adjusters/self-adjusters, other related brake hardware, and backing support plates; lubricate and reassemble.P-1815045.11W15.Inspect wheel cylinders for leaks and proper operation; remove and replace as needed.P-2815045.11W16.Pre-adjust brake shoes and parking brake; install brake drums or drum/hub assemblies and wheel bearings; perform final checks and adjustments.P-2815045.11W1TaskPriorityMLRASTMASTChapterSTC Course #7.Install wheel and torque lug nuts.P-1Fund, 20Disc Brake Diagnosis and Repair1.Diagnose poor stopping, noise, vibration, pulling, grabbing, dragging, or pulsation concerns; determine necessary action.P-19, 1015045.11W12.Remove and clean caliper assembly; inspect for leaks and damage/wear to caliper housing; determine necessary action.P-11015045.11W13.Clean and inspect caliper mounting and slides/pins for proper operation, wear, and damage; determine necessary action.P-11015045.11W14.Remove, inspect, and replace pads and retaining hardware; determine necessary action.P-11015045.11W100510.10W5.Lubricate and reinstall caliper, pads, and related hardware; seat pads and inspect for leaks.P-11015045.11W16.Clean and inspect rotor; measure rotor thickness, thickness variation, and lateral runout; determine necessary action.P-11215045.11W17.Remove and reinstall rotor.P-110, 1215045.11W18.Refinish rotor on vehicle; measure final rotor thickness and compare with specifications.P-11215045.11W10305230059.Refinish rotor off vehicle; measure final rotor thickness and compare with specifications.P-11215045.11W110.Retract and re-adjust caliper piston on an integrated parking brake system.P-31015045.11W111.Check brake pad wear indicator; determine necessary action.P-21015045.11W100510.10WTaskPriorityMLRASTMASTChapterSTC Course #12.Describe importance of operating vehicle to burnish/break-in replacement brake pads according to manufacturer’s recommendations.P-11015045.11W1Power-Assist Units Diagnosis and Repair1.Check brake pedal travel with, and without, engine running to verify proper power booster operation.P-21315045.11W12.Check vacuum supply (manifold or auxiliary pump) to vacuum-type power booster.P-11315045.11W13.Inspect vacuum-type power booster unit for leaks; inspect the check-valve for proper operation; determine necessary action.P-11315045.11W14.Inspect and test hydraulically-assisted power brake system for leaks and proper operation; determine necessary action.P-31315045.11W115045.12T25.Measure and adjust master cylinder pushrod length.P-313Miscellaneous (Wheel Bearings, Parking Brakes, Electrical, ETC.) Diagnosis and Repair1.Diagnose wheel bearing noises, wheel shimmy, and vibration concerns; determine necessary action.P-321, 3150240.16T12.Remove, clean, inspect, repack, and install wheel bearings; replace seals; install hub and adjust bearings.P-12103510.05W3.Check parking brake cables and components for wear, binding, and corrosion; clean, lubricate, adjust or replace as needed.P-21115045.11W14.Check parking brake operation and parking brake indicator light system operation; determine necessary action.P-14, 1115045.11W1TaskPriorityMLRASTMASTChapterSTC Course #5.Check operation of brake stop light system.P-1415045.11W16.Replace wheel bearing and race.P-22103510.05W7.Remove and reinstall sealed wheel bearing assembly.P-22103510.05WElectronic Brake, Traction and Stability Control Systems Diagnosis and Repair1.Identify and inspect electronic brake control system components; determine necessary action.P-314, 1513044.11W-R215045.11W215045.13T115045.16T12.Identify traction control/vehicle stability control system components.P-314, 1713044.11W-R215045.11W23.Describe the operation of a regenerative braking system.P-31618420.05W18443.01W-R24.Diagnose poor stopping, wheel lock-up, abnormal pedal feel, unwanted application, andnoise concerns associated with the electronic brake control system ; determine necessaryaction.P-21513044.11W-R215045.11W25.Diagnose electronic brake control system electronic control(s) and components by retrieving diagnostic trouble codes, and/or using recommended test equipment; determine necessary action.P-21513044.11W-R215045.11W250250.21T16.Depressurize high-pressure components of an electronic brake control system.P-31513044.11W-R215045.11W27.Bleed the electronic brake control system hydraulic circuits.P-115, 1613044.11W-R215045.11W2CHAPTER 1Braking System Components and Performance StandardsANSWERS TO REVIEW QUESTIONS:List the differences between drum brakes and disc brakes. Disc brakes squeeze two friction pads against both sides of a rotor whereas in a drum brake, the friction material is forced outward against a rotating drum.List the six brake subsystem categories. The six brake subsystem categories include: apply, boost, hydraulic, wheel brakes, brake balance control, and instrument panel warning lights.Explain how ABS units prevent wheel lockup.An antilock brake system pulses the brake on and off to prevent the tires from skidding during an ABS event.List ten of the brake tests performed under the Federal Motor Vehicle Safety Standard (FMVSS 135). The ten tests performed under the FMVSS 135 include: ABS performance, adhesion utilization, cold effectiveness, high-speed effectiveness, stops with engine off, antilock function failure, variable brake proportioning, hydraulic circuit failure, brake power-assist unit inoperative, parking brake.ANSWERS TO CHAPTER QUIZ:Disc brakes use replaceable friction material called __________. a.? Liningsb. Pads Xc. Cored. WebDrum brakes use replaceable friction material called ________. a.? Shoes X b. Padsc. Cored. WebTechnician A says that a power-assisted brake reduces stopping distances compared with a non-power-assisted brake system. Technician B says that the power-assisted brake system reduces the force that the driver must exert on the brake pedal. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and Bd. Neither Technician A nor BA locked wheel ___________________ to the road surface than a rolling wheel. a. Has less traction Xb. Has greater traction Technician A says that all vehicles equipped with ABS will experience a pulsating brake pedal even during normal braking. Technician B says that ABS will result in quicker stops on all road surfaces. Which technician is correct? a. Technician A onlyb. Technician B only c. Both Technicians A and Bd. Neither Technician A nor BXThe FMVSS 135 standards determine ____________. a. The design of the braking systemb. The performance of the braking system Xc. The materials used in the braking systemd. All of the aboveAn owner of a vehicle equipped with ABS brakes complained that whenever he tried to stop on icy or slippery roads, the brake pedal would pulse up and down rapidly. Technician A says that this is normal for many ABS units. Technician B says that the ABS unit is malfunctioning. Which technician is correct? a. Technician A only Xb. Technician B onlyc. Both Technicians A and Bd. Neither Technician A nor BElectric adjustable pedals change the position of ______. a. The parking brake onlyb. The accelerator pedal onlyc. The brake pedal onlyd. Both the accelerator and brake pedal X9. All of the following are specified by the FMVSS 135 except ________________. a. Brake burnish procedureb. Variable brake proportioning systemc. Brake noise levels Xd. Cold effectiveness10. What is the purpose of any brake repair? a. Reduce noise during brakingb. Replace pads and liningsc. Restore proper brake pedal heightd. Restore like-new performance XCHAPTER 2Braking System PrinciplesANSWERS TO REVIEW QUESTIONS:What is kinetic energy? Kinetic energy is the energy of a mass in motion.How is mechanical advantage used in the braking system? Mechanical advantage is used in the brake pedal mechanism which uses the lever principle.What is meant by the term “coefficient of friction”? The coefficient of friction is the measurement of the amount of friction between two surfaces. The higher the number from zero to one, the greater the friction.Why do brakes fade due to excessive heat or water? Brakes fade due to heat because of gassing of the resins in the lining as well as the inability of the braking system to absorb additional heat when the brakes are hot. Fade due to water is caused by water getting between the rotor or drum and the friction material, thereby limiting or reducing the friction between the two surfaces.ANSWERS TO CHAPTER QUIZ:All of the following are correct statements about braking except ______________. Kinetic energy must be absorbed by the braking system.Kinetic energy of a vehicle doubles when the speed doubles. XThe heavier the vehicle, the greater the kinetic energy when moving.If the vehicle weight is doubled, the kinetic energy of a moving vehicle is doubled.Technician A says that the front brakes do most of the braking because the front brakes are larger. Technician B says that due to weight transfer, most of the braking force needs to be done by the front brakes. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and B d. Neither Technician A nor BThe brake pedal assembly uses a mechanical lever to ______________________. a. Increase the driver’s force on the brake pedal applied to the master cylinder Xb. Increase the distance the brake pedal needs to be depressed by the driverc. Decrease the driver’s force on the brake pedal applied to the master cylinderd. Allow for clearance between the brake pedal and the floor when the brakes are applied4. The friction between two surfaces is affected by all except ______________. Speed difference between the two surfaces XSurface finishFrictional materialHeatTechnician A says that the thicker or heavier the disc brake rotor, the more heat can be absorbed. Technician B says that the faster the vehicle is traveling when the brakes are applied, the greater the amount of heat created in the brake system. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor B6. All of the following are types of brake fade except ____________________. a. Mechanical fadeb. Lining fadec. Gas faded. Rotor fade X7. Brake fade caused by water can occur ____________________. a. Only if the vehicle is driven in water above the centerline of the axleb. Whenever it rains and the roads are wet or dampc. Due to moisture in the air on a humid dayd. When driving through water puddles or during a severe rainstorm X8. What can the driver do to reduce the possibility of brake fade caused by heat? a. Ride the brakes to keep the shoes and pads against the drum or rotorb. Pump the brake pedal while descending a steep hillc. Select a lower transmission drive range Xd. Shift the transmission into neutral and allow the vehicle to coast down long or steep hillsMaximum deceleration rates for a typical passenger car or light truck is __________. 1 to 3 ft/sec5 to 10 ft/sec16 to 32 ft/sec2 X200 to 250 ft/sec2Disc brake pads can reach temperatures as high as _____________. a. 300°F (150°C)b. 1,000°F (540°C)c. 1,300°F (700°C) Xd. 2,000°F (1,093°C)CHAPTER 3Brake Hydraulic SystemsANSWERS TO REVIEW QUESTIONS:1. Explain Pascal's Law. Pascal’s Law states that when force is applied to a confined liquid, the pressure is equally transmitted undiminished and in every direction.2. Describe how a master cylinder works. The force of the driver’s foot on the brake pedal compresses brake fluid in the master cylinder using two pistons, one for each circuit.3. Discuss the difference between a front/rear split and a diagonal split master cylinder. A front/rear split hydraulic system separates the two front wheel brakes into one circuit and the two rear wheel brakes into another circuit whereas, a diagonally split system separates the brakes into right front and left rear on one circuit and left front and right rear on the other circuit.4. What is the difference between checking for venting (compensation) and bypassing? Venting occurs every time the brake pedal is depressed, which forces a small amount of brake fluid up into the master cylinder reservoir as the primary piston is moving forward. Bypassing is a fault where brake fluid from the rear circuit is forced into the front brake circuit.ANSWERS TO CHAPTER QUIZ:Two technicians are discussing master cylinders. Technician A says that it is normal to see fluid movement in the reservoir when the brake pedal is depressed. Technician B says a defective master cylinder can cause the brake pedal to slowly sink to the floor when depressed. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BIf the brake pedal linkage is not adjusted correctly, brake fluid may not be able to expand back into the reservoir through the ________________ port of the master cylinder when the brakes get hot. Vent port (forward hole) XReplenishing port (rearward hole)The primary brake circuit fails due to a leak in the lines, leaving the secondary section of a front/rear split master cylinder. Technician A says that the driver will notice a lower than normal brake pedal and some reduced braking power. Technician B says that the brake pedal will "grab" higher than normal. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BTwo technicians are discussing a problem where the brake pedal travels too far before the vehicle starts to slow. Technician A says that the brakes may be out of adjustment. Technician B says that one circuit from the master cylinder may be leaking or defective. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BAir in the lines will cause what type of problem? Vibration in the brake pedal during stopsLow spongy brake pedal XBrake noiseHard brake pedalThe master cylinder is able to move about how much brake fluid during each brake application? One tablespoonOne teaspoon XOne cu. in.50 mlBrake fluid pressure is measured in what unit? a. Sq. in.b. Poundsc. Inchesd. psi XHow much brake fluid is in a typical master cylinder reservoir? a. One gallonb. Enough to allow all brakes to become completely worn Xc. 15 to 20 litersd. One pintWhat part in the master cylinder helps keep air from contacting the brake fluid yet allows the fluid level to drop as the disc brakes wear? a. Vent valveb. Compensating valec. Residual valved. Rubber diaphragm or floating disc XThe brakes on a vehicle work okay for a while, then the vehicle slows because the brakes self-applied. Technician A says that an overfilled master cylinder could be the cause. Technician B says that a blocked vent port (compensating port) could be the cause. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BCHAPTER 4Hydraulic Valves and SwitchesANSWERS TO REVIEW QUESTIONS:Explain how dynamic rear proportioning (DRP) can take the place of the proportioning valve. Dynamic rear proportioning uses the ABS controller software and the rear wheel hydraulic control circuits to maintain optimum front-to-rear balance under all conditions.List the three possible reasons that could cause the red brake warning lamp to come on during driving. The red brake warning lamp can be turned on due to low brake fluid, unequal brake fluid pressure between circuits, or by the application of the parking brakes.Explain why metering valves are not used on all vehicles. Metering valves are not needed on front-wheel-drive vehicles because of the forward weight bias and they use a diagonal-split hydraulic system instead of a front/rear split system used on rear-wheel-drive vehicles.4. Explain the split point and the slope of a proportioning valve. The proportioning valve limits the pressure to the rear brakes after a certain pressure is achieved. This pressure is called the split point. A portion of the front brake pressure that is sent to the rear brakes is called the slope.ANSWERS TO CHAPTER QUIZ:Technician A says that a late model vehicle with ABS will also have a proportioning valve as a back-up. Technician B says that all vehicles have a proportioning valve. Which technician is correct?Technician A onlyTechnician B onlyBoth Technicians A and BNeither Technician A nor B XThe rear brakes lock up during a regular brake application. Technician A says the metering valve could be the cause. Technician B says that stuck front disc brake calipers could be the cause. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BThe rear wheels lock up during hard braking. Technician A says that a defective metering valve could be the cause. Technician B says that a defective proportioning valve could be the cause. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BA combination valve could include__________________. Metering and proportioning valvesProportioning and pressure-differential switchProportioning and metering valves, and pressure-differential switchAny of the above depending on the make and model of the vehicle XWhich one of these sends an electrical signal to the antilock brake control module? Pedal position sensor XResidual check valvePressure differential switchAll of theseTechnician A says that the red brake warning light can be turned on if a difference in pressure is detected by the pressure-differential switch. Technician B says that the red brake warning light can be turned on if the brake fluid level sensor detected low brake fluid level. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BWhich type of vehicles most often do not use metering valves? Rear-wheel driveFour-wheel driveFront-wheel drive XAll-wheel driveTechnician A says that some proportioning valves have one control valve that controls both rear brakes. Technician B says that some proportioning valves have two control valves, one for each rear wheel brake. Which technician is correct? Technician A only Technician B onlyBoth Technicians A and B XNeither Technician A nor BThe button on the _______________ valve should be held when pressure bleeding the brakes. Metering XProportioningPressure-differentialResidual checkA typical brake light is electrically _________________. Normally open XNormally closedCHAPTER 5Brake Fluid and LinesANSWERS TO REVIEW QUESTIONS:1. What is the difference between DOT 3, DOT 4, DOT 5.1, and DOT 5 brake fluid? DOT 3, 4, and 5.1 are polyglycol based whereas, DOT 5 is silicone based. DOT 4 and DOT 5.1 have higher boiling points, as well as some additive differences.2. List four things that should be done during a thorough inspection of the brake fluid. The four things that should be done during an inspection of the brake fluid include: checking for proper level, checking for color and condition, testing for absorbed moisture, and testing for contamination.3. List four precautions that should be followed when handling brake fluid. Precautions for handling brake fluid include: store the brake fluid only in its original container, clean the top of containers before opening, do not reuse brake fluid, and do not transfer brake fluid to any other container that could have contained oil, gasoline, or antifreeze.4. What are the two types of flares used on brake lines? The two types of brake line flares include ISO and double-lap flare.5. Why are some brake lines coiled? Some brake line is coiled to allow for movement between brake system components without breaking.ANSWERS TO CHAPTER QUIZ:The type of brake fluid most often recommended by vehicle manufacturers is _______. DOT 3 XDOT 4DOT 5DOT 5.1Which of the following is not a characteristic of conventional brake fluid? Absorbs moisture from the airRemoves paint if spilled on vehicle surfacesLasts the life of the vehicle unless there is a leak XIs clear or amber in colorTechnician A says that DOT 5 brake fluid can be added to DOT 3 brake fluid. Technician B says that it is wise to purchase brake fluid that is in a sealed container. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BAs brake fluid ages, what happens? The boiling temperature decreases XThe boiling temperature increasesThe viscosity decreasesThe color changes to purpleTechnician A says that glycol-based brake fluid causes the seals to swell slightly. Technician B says the DOT 5 (silicone-based) brake fluid causes rubber seals to swell slightly. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BThe two types of flares used on brake lines are _______________. SAE and DOTDouble flare and ISO XBall flare and bubble flareSAE and double flareTwo technicians are discussing why the brake lines are coiled near the master cylinder on many vehicles. Technician A says that these coils help prevent moisture from flowing from the master cylinder to the calipers. Technician B says that they help prevent cracks that could be caused by vibrations. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BFlexible brake hose should be inspected for all of the following except: CracksLeakageTwistingColor XWhy should brake calipers be supported by a wire during brake service and not allowed to hang by the flexible brake hose? To keep air from getting into the systemTo help prevent damage to the brake hose XTo hold the caliper higher than the master cylinder to prevent fluid lossTo prevent bending the hose support bracketUsed brake fluid should be _____________. Mixed with and recycled with used oilPoured down the drainDisposed of properly according to State and local laws XPoured onto open ground to reduce dustCHAPTER 6Brake Bleeding Methods and ProceduresANSWERS TO REVIEW QUESTIONS:1. Describe how to bench bleed a master cylinder. A master cylinder is bench bled by clamping the ears (not the housing) in a vise and stroking the master cylinder with tubes installed at the outlet until all of the air is bled from the unit.2. List the steps necessary to manually bleed a brake hydraulic system. The steps necessary to manually bleed a hydraulic brake system includes: opening the bleeder, having an assistant slowly depress the brake pedal, closing the bleeder valve, having an assistant slowly release the brake pedal, and then wait 15 seconds. 3. Discuss the equipment and the procedures needed to pressure bleed a brake hydraulic system. A pressure bleeder and adapter are needed to pressure bleed a hydraulic brake system. Do not exceed 20 psi or the pressure specified by the vehicle manufacturer and follow the specified bleeding sequence.4. Explain how to gravity bleed a brake hydraulic system. To gravity bleed a brake hydraulic system, simply open a bleeder(s) and allow gravity to force brake fluid downward and out of the open bleeder valve. Any trapped air will escape before the fluid flows.5. Describe how to vacuum bleed a brake hydraulic system. A vacuum pump is attached to the open bleeder valve and brake fluid is drawn from the wheel brake until all of the foam and air have been removed.ANSWERS TO CHAPTER QUIZ:The button on the ___________ valve should be held when pressure bleeding the brakes. a. Metering Xb. Proportioningc. Pressure-differentiald. Residual checkThe brake bleeding procedure usually specified for a rear-wheel vehicle with a dual split master cylinder is _________________. RR, LR, RF, LF XLF, RF, LR, RRRF, LR, LF, RRLR, RR, LF, RFTwo technicians are discussing bleeding a master cylinder on the car. Technician A says that the secondary section of the master cylinder should be bled first. Technician B says that the primary section should be bled first. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and B d. Neither Technician A nor BTwo technicians are discussing how to loosen bleeder valves. Technician A says that a shock is usually necessary to break the taper at the base of the valve. Technician B says to apply steady, loosening torque to the bleeder valve using a 6-point wrench. Which technician is correct? a. Technician A only Xb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor BTechnician A says that the brake pedal should be depressed with as much force as possible during the normal bleeding procedure. Technician B says that the brake pedal should be pumped rapidly during this manual bleeding procedure to force the air down toward the bleeder valve(s). Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor B XVacuum is applied where during vacuum bleeding? a. At each wheel brake bleeder valve Xb. At the master cylinder reservoirc. At the vacuum booster check valved. At the metering valve end of the combination valveThe bleeder is opened at a caliper and no brake fluid flows out. Technician A says that this is normal and that brake fluid should not flow or drip out of an open bleeder valve. Technician B says that the vent port in the master cylinder may be blocked. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and B d. Neither Technician A nor BThe usual maximum pressure that should be used when pressure bleeding a brake system is ______. 20 psi30 psi X50 psi70 psiHow does a bleeder valve seal? a. O-ringb. Threadsc. Lip seald. Tapered end XAir in the brake hydraulic system can cause all except ___________. Spongy brake pedalb. Hard brake pedal Xc. Lower than normal brake pedald. May require the driver to “pump up” the brakes before they will stop the vehicleCHAPTER 7Drum BrakesANSWERS TO REVIEW QUESTIONS:Describe the difference between a dual-servo and a leading–trailing drum brake system. A dual-servo brake uses the force of the primary brake shoe to engage the secondary shoe against the drum with even greater force. In a leading/trailing drum brake, each shoe works independently resulting in a more linear brake application.List all the parts of a typical drum brake. The parts of a typical drum brake include, backing plate, anchor pin, primary (leading) shoe, secondary shoe, hold-down springs, adjusting levers, and return springs.Explain how a self-adjusting brake mechanism works. A typical self-adjuster moves the star wheel adjuster when the brakes are released after a brake application when the vehicle is traveling in reverse.What is the meaning of the last two letters of the lining or pad edge code? The first letter represents the coefficient of friction when the tire is cold and the second letter represents the coefficient of friction when the tire is hot.ANSWERS TO CHAPTER QUIZ:Two technicians are discussing drum brake shoes. Technician A says that forward and rear-facing shoes are the same and can be installed in either position on any drum brake system. Technician B says that the shorter lining should always be placed toward the front of the vehicle. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor B XTwo technicians are discussing brake lining edge codes. Technician A says that the code can identify the manufacturer. Technician B says that all friction material from the same manufacturer will have the same edge codes. Which technician is correct? a. Technician A only Xb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor BTechnician A says that starwheel adjusters use different threads (left- and right-handed) for the left and right sides of the vehicle. Technician B says that a pawl contacts the teeth of the starwheel adjuster. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTechnician A says that drum brakes can fail to slow the vehicle if driven through deep water. Technician B says that when drum brakes get hot, the brake pedal will drop because the drum expands away from the shoes. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that some self-adjusters used on drum brakes work when the brakes are applied, and then released while moving in reverse. Technician B says that some adjusters when the brakes are applied. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BDrum brake shoes __________________________. a. Can have riveted liningsb. Can have bonded liningsc. Can have one shoe that is longer than the other on the same wheel braked. All of the above are possible XWhich lining does most of the braking on a dual-servo brake? a. Primary (forward facing)b. Secondary (rearward facing) Xc. Both contribute equallyd. Depends on the speed of the vehicleWhich lining does most of the braking on a leading/trailing brake? a. Leading (forward facing) Xb. Trailing (rearward facing)c. Both contribute equallyd. Depends on the speed of the vehicleTwo technicians are discussing drum brake self adjusters. Technician A says that a frozen starwheel adjuster could cause the brakes to lock up due to excessive clearance between the shoes and drum. Technician B says that some brakes do not use a starwheel as an adjusting mechanism. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and B d. Neither Technician A nor BA typical drum brake backing-plate has how many shoe support pads (also called ledges)? a. 3b. 4c. 6 Xd. 8CHAPTER 8Drum Brake Diagnosis and ServiceANSWERS TO REVIEW QUESTIONS:Explain how to remove a brake drum. Before a brake drum is removed, the wheel and speed nut(s) (if equipped) must be removed. A hubless drum should slide off of the bearing hub, but some drums may come equipped with threaded holes where bolts can be installed to remove the drums.List all items that should be lubricated on a drum brake. The items that should be lubricated on a drum brake include:a. The six ledges on the backing plateb. The shoe anchorc. The self-adjuster at both ends and on the threadsList the steps necessary to follow when replacing drum brake linings. The steps necessary when replacing drum brake linings include: cleaning and lubricating the backing plate, installing the shoes and hold-down springs, installing the self-adjuster mechanism and return springs.Explain why many vehicle manufacturers do not recommend the wheel cylinder be honed. Many wheel cylinders are made using a bearingized surface which would be removed if honed.ANSWERS TO CHAPTER QUIZ:Technician A says that the tinnerman nuts are used to hold the brake drum on and should be reinstalled when the drum is replaced. Technician B says that a drum should be removed inside a sealed vacuum enclosure or washed with a brake washer to prevent possible asbestos dust from being released into the air. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and Bd. Neither Technician A nor BThe backing plate should be replaced if the shoe contact areas (pads or ledges) are worn more than __________. 1/2 in. (13 mm)1/4 in. (7 mm)1/8 in. (4 mm)1/16 in. (2 mm) XTechnician A says that silicone brake grease can be used to lubricate the shoe contact ledges. Technician B says that synthetic brake grease, lithium brake grease, or antiseize compound can be used as a brake lubricant. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BMost brake experts and vehicle manufacturers recommend replacing brake lining when the lining thickness is ____________________. 0.030 in. (0.8 mm)0.040 in. (1.0 mm)0.050 in. (1.3 mm)0.060 in. (1.5 mm) XTechnician A says that starwheel adjusters use different threads (left- and right-handed) for the left and right sides of the vehicle. Technician B says that the threads and end caps of the adjusters should be lubricated with brake grease before being installed. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that many vehicle manufacturers recommend that wheel cylinders not be honed because of the special surface finish inside the bore. Technician B says that some experts recommend that the wheel cylinders be replaced every time the brake linings are replaced. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BMost manufacturers recommend that brake parts should be cleaned with ____________. a.?Clean water onlyb.?Denatured alcohol Xc.?Stoddard solventd.?Detergent and waterOld brake shoes are often returned to the manufacturer when new friction material is installed. These old shoes are usually called the ______________. a.?Core Xb.?Webc.?Rimd.?NibAfter assembling a drum brake, it is discovered that the brake drum will not fit over the new brake shoes. Technician A says that the parking brake cable may not have been fully released. Technician B says to check to see if both shoes are contacting the anchor pin. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that dry brake shoe pads can cause a squeaking noise as the brakes are applied. Technician B says that grease on the brake lining can cause the brakes to grab. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BCHAPTER 9Disc BrakesANSWERS TO REVIEW QUESTIONS:What are the advantages and disadvantages of disc brakes? Disc brake advantages include: fade resistance, self-adjustment, and freedom from pull. Disadvantages include: lack of self-energizing or servo action, brake noise, brake dust, and poor parking brake performance.What parts are included in a typical disc brake? A typical disc brake includes the caliper assembly, pads, clips, and mounting hardware.How does a low-drag caliper work? A low-drag caliper works by retracting the caliper piston further into the caliper bore and away from the rotor. In a low-drag caliper design, the groove for the square-cut O-ring is V-shaped, allowing for more retraction.What mechanism is used to apply the parking brake on a vehicle equipped with rear disc brakes? A vehicle equipped with rear disc brakes uses either a mechanically actuated drum brake inside the rear rotors or a mechanically activated caliper piston.What do the abbreviations NAO, NAS, and CFRC mean? NAO – nonasbestos organic, NAS – nonasbestos synthetic, CFRC – carbon fiber-reinforced carbonANSWERS TO CHAPTER QUIZ:What part causes the disc brake caliper piston to retract when the brakes are released? Return (retracting) springThe rotating rotor (disc) that pushes the piston backThe square-cut O-ring XThe caliper bushingsTwo technicians are discussing the reason that the brake fluid level in the master cylinder drops. Technician A says that it may be normal due to the wear of the disc brake pads. Technician B says that a low brake fluid level may indicate a hydraulic leak somewhere in the system. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTwo technicians are discussing a floating-type disc brake caliper. Technician A says that if the caliper slides are corroded, one pad may wear more than the other pad on the same wheel brake. Technician B says that if a caliper slide is corroded, reduced braking may occur. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTechnician A says that disc brakes are self-adjusting and the brake pedal height should not become lower as the disc brake pads wear. Technician B says that as the disc brake pads wear, the level of brake fluid in the master cylinder reservoir drops. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BWhich type of disc brake caliper may leak brake fluid more often? SlidingFixed XFloatingSingle pistonA quick take-up master cylinder is required when what type of caliper design is used on a vehicle? FixedTwo-pistonSlidingLow-drag XTechnician A says that all vehicles equipped with rear disc brakes use a parking brake that is integrated in the caliper. Technician B says that all vehicles equipped with rear disc brakes use a small drum brake inside the rear rotor for a parking brake. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B Neither Technician A nor B XThe brake pad edge code letters “FF” mean ___________________________. Brand nameCoefficient of friction rating XQuality factor Noise level ratingSemimetallic brake pads are made by a process called _______________. a. Sintering Xb. Meltingc. Gratingd. CompositionTechnician A says that riveted disc brake pads are often quieter than bonded disc brake pads. Technician B says integrally molded disc brake pads are molded into holes in the steel backing of the pads. Which technician is correct?Technician A onlyTechnician B onlyBoth technicians A and BXNeither technician nor B CHAPTER 10Disc Brake Diagnosis and ServiceANSWERS TO REVIEW QUESTIONS:List what parts are included in a typical overhaul kit for a single piston floating caliper. A typical overhaul kit for a single piston floating caliper consists of a dust seal and a square-cut O- ring.Describe how to remove caliper pistons and perform a caliper overhaul. To remove a caliper piston, first remove the brake hose then apply compressed air (shop air) to the inlet of the caliper. The air pressure exerts enough force to remove the piston from the caliper bore. After piston removal and a thorough cleaning and inspection, a new square cut O-ring should be installed in the groove of the caliper bore. After lubricating the caliper piston with clean brake fluid, the caliper piston is then pushed into the caliper bore. Check to see that the caliper seal is correctly installed. Properly seat the dust seal.Explain what causes disc brake squeal and list what a technician can do to reduce or eliminate the noise. Disc brake squeal is often caused by movement of the disc brake pad during braking. To reduce disc brake squeal, all mating surfaces of the brake should be clean and lubricated. Always use OEM recommended clips and anti-squeal shims. To further reduce noise, do not machine a disc brake rotor more than absolutely necessary.ANSWERS TO CHAPTER QUIZ:Uneven disc brake pad wear is being discussed. Technician A says the caliper piston may be stuck. Technician B says the caliper may be stuck on the slides and unable to "float." Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BA "chirping" noise is heard while the vehicle is moving forward, but stops when the brakes are applied. Technician A says that the noise is likely caused by the disc brake pad wear sensors. Technician B says the noise is likely a wheel bearing because the noise stops when the brakes are applied. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BTechnician A says that disc brake pads should be replaced when worn to the minimum allowable thickness. Technician B says the pads should be removed and inspected whenever there is a brake performance complaint. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BA typical disc brake caliper overhaul (OH) kit usually includes what parts? Square-cut O-ring seal and dust boot XReplacement caliper piston and dust bootDust boot, return spring, and caliper sealDisc brake pad clips, dust boot, and caliper piston assemblyTechnician A says that a lack of lubrication on the back of the disc brake pads can cause brake noise. Technician B says that pads that are not correctly crimped to the caliper housing can cause brake noise. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTwo technicians are discussing ways of removing a caliper piston. Technician A says to use compressed air. Technician B says to use large pliers. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BWhich is not a recommended type of grease to use on brake parts? Silicone greaseWheel bearing (chassis) grease XSynthetic greaseAntiseize compoundTechnician A says that a loaded caliper includes an overhauled caliper assembly but no brake pads or hardware. Technician B says that a loaded caliper includes the pads and all needed hardware. Which technician is correct? Technician A onlyTechnician B onlyXBoth Technicians A and BNeither Technician A nor BA vehicle is hoisted during routine service and the service technician discovers that the left front wheel does not turn when force is applied. Technician A says that there could be a brake fluid restriction between the master cylinder and the brake. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTechnician A says that a steel piston should be cleaned with sandpaper to remove rust. Technician B says that the brake assembly fluid or clean brake fluid should be used to lubricate the caliper pistons before installing in the caliper. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and B Neither Technician A nor BCHAPTER 11Parking Brake Operation, Diagnosis, and ServiceANSWERS TO REVIEW QUESTIONS:Describe how a typical parking brake functions on a vehicle equipped with rear drum brakes. The parking brake uses a cable to mechanically (rather than hydraulically) apply the drum brake linings. When the parking brake is applied, a cable moves a parking brake lever that forces the brake shoe against the brake drum.Describe how a typical parking brake functions on a vehicle equipped with an integral rear disc brake system. The parking brake uses a cable to mechanically apply the caliper piston on a vehicle equipped with integral rear disc brakes. An actuating screw thread inside the caliper piston pushes the caliper piston against the disc brake rotor.Explain how to adjust a parking brake properly. To properly adjust the parking brake cable, the rear brake must first be inspected and adjusted if necessary. The usual procedure for parking brake cable adjustment includes applying the parking brake 3 or 4 "clicks" and adjusting the cable until the rear brakes are applied.Discuss some service procedures necessary for an electronic parking brake system.Use a scan tool to disable the cable adjuster prior to disassembly in order to put slack in the cables so that they can be disconnected. Use the scan tool to enable the cable adjuster. Service Programming System (SPS) programming and a scan tool parking brake calibration procedure may be required if the EPB module is replaced.ANSWERS TO CHAPTER QUIZ:Technician A says that the parking brake cable should be adjusted at each wheel. Technician B says that the parking brake cable adjustment is usually done after adjusting the rear brakes. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and Bd. Neither Technician A nor BTechnician A says that the parking brake hand lever can turn on the red brake warning lamp. Technician B says that a foot-operated parking brake can turn on the red brake warning lamp. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that if the parking brake cable is adjusted too tight, the rear brakes may drag and overheat. Technician B says that the parking brake is adjusted properly if the cable is tight when in the released position. Which technician is correct? a. Technician A only Xb. Technician B onlyc. Both Technicians A and Bd. Neither Technician A nor BOn most drum brake systems, the parking brake lever and strut initially transfers the pulling force of the parking brake cable against the _____________________. a.?Primary shoe Xb.?Secondary shoec. Adjuster assemblyd. Wheel cylinderOn most vehicles, the anti-rattle spring (strut spring) should be installed on the parking brake strut toward the _____ of the vehicle. a.?Front Xb.?Rearc. Middled. LeftIn a typical integral rear disc brake caliper, the parking brake cable moves the ___________. a.?Caliperb.?Actuator screw Xc.?Auxiliary pistond.?RotorThe rear brakes should be inspected, and adjusted if necessary, if the parking brake requires more than _______. a.?5 clicksb.?10 clicks Xc.?15 clicksd.?20 clicksA rear drum brake is being inspected. The primary shoe is not contacting the anchor pin at the top. Technician A says that this is normal. Technician B says that the parking brake cable may be adjusted too tight or is stuck. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and Bd. Neither Technician A nor BTechnician A says that a hose clamp can be used to compress the retainer fingers of a parking brake cable in order to remove it from the backing plate. Technician B says a box-end wrench can be used instead of a hose clamp. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that an electric parking brake (EPB) uses an electric motor to pull on the parking brake cable. Technician B says that the key must be turned on before the electric parking brake can be released. Which technician is correct? a. Technician A onlyb. Technician B only c. Both Technicians A and B Xd. Neither Technician A nor BCHAPTER 12Machining Brake Drums and RotorsANSWERS TO REVIEW QUESTIONS:Explain the difference between “machine to” specifications and “discard.” "Machine to" specifications indicate the minimum thickness (rotor) or maximum diameter (drum) that should be machined. "Discard" dimension is the maximum diameter (drum) or minimum thickness (rotor) that is allowed for wear after machining.List the steps for machining a brake drum. The steps necessary to machine brake drums include:Mount the drum on the lathe and install a damperPerform a scratch cutRotate the drum and perform a second scratch cutStart the lathe and perform a rough, then a finish cutDescribe how to measure a disc brake rotor for lateral runout and thickness variation. Measuring a disc brake rotor for lateral runout involves removing any bearing end-play and mounting a dial indicator (gauge) against the rotor. Any movement of the dial indicator while the rotor is being rotated indicates lateral runout. Thickness variation is measured using a micrometer about 1" from the outside of the rotor and measuring at least four or more equally spaced locations.List the steps for machining a disc brake rotor. The steps necessary for machining a disc brake rotor include:Mount the rotor to the lathe and install a damperPerform a scratch cutMove the rotor 180° and perform a second scratch cut.Start the lathe and perform a rough cut and a finish cutUse sandpaper or other tools to create a smooth, non-directional surface finish.Describe what is necessary to achieve “like new” disc brake rotor finish. A "like new" disc brake rotor finish is extremely smooth (less than 40 micro inches) and free from deep grooves and rust.ANSWERS TO CHAPTER QUIZ:Technician A says that aluminum brake drums use cast iron friction surfaces. Technician B says that up to 0.030 in. (0.8 mm) should be left after machining a drum to allow for wear. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that hard spots in a brake drum should be removed using a carbide-tip machining tool. Technician B says that the drum should be replaced if hard spots are discovered. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BTechnician A says that brake drums on the same axle should be close to the same inside diameter for best brake balance. Technician B says that a brake drum may be cracked if it rings like a bell when tapped with a light steel hammer. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BA hubless brake drum cannot be machined because it cannot be held in a lathe. a.?Trueb.?False XThe major reason for brake pedal pulsation during braking is due to excessive rotor thickness variation. a.?True Xb.?FalseRotor finish is measured in _______________________. a.?Millimetersb.?Inchesc.?Microinches Xd.?CentimetersThe lower the Ra of a rotor, the _______ the surface. Smoother XRougherHigherLowerA disc brake rotor is being installed on a lathe for machining. During the setup a scratch test is performed. The scratch extended all the way around the rotor. Technician A says that the rotor should be loosened, rotated 180°, and retightened. Technician B says that the rotor is not warped. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BTypical maximum rotor runout specifications are ______________________. a.?0.0003 to 0.0005 in. (0.008 to 0.013 mm)b.?0.003 to 0.005 in. (0.08 to 0.13 mm) Xc.?0.030 to 0.050 in. (0.8 to 1.3 mm)d.?0.300 to 0.500 in. (8.0 to 13 mm)10.??Typical maximum rotor thickness variation (parallelism) specifications are _____________. a.?0.0003 to 0.0005 in. (0.008 to 0.013 mm) Xb.?0.003 to 0.005 in. (0.08 to 0.13 mm)c.?0.030 to 0.050 in. (0.8 to 1.3 mm)d.?0.300 to 0.500 in. (8.0 to 13 mm) CHAPTER 13Power Brake Unit Operation, Diagnosis, and ServiceANSWERS TO REVIEW QUESTIONS:Describe the purpose and function of the one-way check valve used on vacuum brake booster units. The purpose and function of the one-way check valve on the vacuum booster supply line is to prevent a loss of vacuum in the booster assembly when the engine is off. A spring-loaded check valve assures that the unit is sealed when the engine is stopped and is no longer producing vacuum.Explain how vacuum is used to assist in applying the brakes. Vacuum is the absence of air pressure. Vacuum is applied to both sides of a rubber diaphragm inside the vacuum booster assembly. When the driver depresses the brake pedal, outside air at full atmospheric pressure enters the backside of the booster. The air pressure "pushes" on the rubber diaphragm that is attached to a rod that pushes on the primary piston of the master cylinder. The air pressure increases the force exerted on the master cylinder resulting in decreased effort by the driver of the vehicle.Describe how to perform a vacuum booster leak test and hydraulic system leak test. The vacuum booster leak test is performed to test if the booster can hold vacuum. Start and run the engine, then stop the engine and wait one minute. Depress the brake pedal several times. A good booster should be able to supply two or more power-assisted stops. They hydraulic system leak test is performed to check the hydraulic system for leaks. After depressing the brake pedal several times, depress and hold the brake pedal. If the brake pedal falls, the hydraulic brake system is leaking.Explain how a Hydro-Boost system functions. The hydro-boost system uses hydraulic pressure from the power steering pump to provide an assist for the driver.ANSWERS TO CHAPTER QUIZ:Two technicians are discussing vacuum brake boosters. Technician A says that a low, soft brake pedal is an indication of a defective booster. Technician B says that there should be at least two power-assisted brake applications after the engine stops running. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BTechnician A says that to check the operation of a vacuum brake booster, the brake pedal should be depressed until the assist is depleted and then start the engine. Technician B says that the brake pedal should drop when the engine starts, if the booster is okay. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BBrake pedal feedback to the driver is provided by the ________________. Vacuum check-valve operationReaction system XCharcoal filter unitVacuum diaphragmThe proper operation of a vacuum brake booster requires that the engine be capable of supplying at least ________________. 15 in. Hg vacuum X17 in. Hg vacuum19 in. Hg vacuum21 in. Hg vacuumThe purpose of the charcoal filter in the vacuum hose between the engine and the vacuum brake booster is to __________________. Filter the air entering the engineTrap gasoline vapors to keep them from entering the booster XAct as a one-way check valve to help keep a vacuum reserve in the boosterDirect the vacuumA defective vacuum brake booster will cause a ___________________. Hard brake pedal XSoft (spongy) brake pedalLow brake pedalSlight hiss noise when the brake pedal is depressedAn accumulator such as that used on hydraulic brake boosters ________________. Reduces brake pedal noiseProvides higher force being fed back to the driver’s footProvides a reserve in the event of a failure XWorks against engine vacuumThe first step in diagnosing a Hydro-Boost problem is ____________________. A pressure test of the pumpA volume test of the pumpTo tighten the power steering drive beltA thorough visual inspection XA brake pedal feels spongy when depressed. Technician A says that a defective hydraulic brake booster could be the cause. Technician B says that a defective vacuum brake booster could be the cause. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and Bd. Neither Technician A nor B XIf the engine stops running, the Hydro-Boost will not be able to provide any power assist for the brakes. TrueFalse XCHAPTER 14ABS Components and OperationANSWERS TO REVIEW QUESTIONS:Describe how an antilock braking system (ABS) works. An antilock braking system works by controlling brake fluid pressure to prevent wheel lockup during braking.List the three stages of ABS operation. The three stages of ABS operation include:Pressure increasePressure holdPressure reductionExplain how wheel speed sensors work. A wheel speed sensor contains a coil of wire surrounding a permanent magnet. As the teeth of the reluctor rotate near the sensor, a varying electrical frequency is generated in the wheel speed sensor. The electronics in the controller use the frequency of this signal to determine wheel speed.Describe the difference between a three- and a four-channel system. A three-channel antilock braking system controls each front wheel as a separate channel, but controls both rear wheels together as a single channel. Four-channel ABS controls all four-wheel brakes individually.ANSWERS TO CHAPTER QUIZ:Technician A says that the ABS system may not result in shorter stopping distance compared to brakes without ABS. Technician B says that a pulsating brake pedal during normal braking is a characteristic feature of most ABS-equipped vehicles. Which technician is correct? Technician A only Technician B onlyBoth Technicians A and B XNeither Technician A nor BThe maximum traction between a tire and the road occurs when the tire is _______________. Locked and skiddingRotating freelySlipping 10 to 20 percent XSlipping 80 to 90 percentTechnician A says that ABS-equipped vehicles can stop quickly and without skidding on all road surfaces even if covered with ice. Technician B says that steering is possible during an ABS stop. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BA customer wanted the ABS checked because of tire chirp noise during hard braking. Technician A says that the speed sensors may be defective. Technician B says that tire chirp is normal during an ABS stop on dry pavement. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BTwo technicians are discussing ABS wheel speed sensors. Technician A says that some ABS systems use a sensor located in the rear-axle pinion gear area. Technician B says that all ABS systems use a wheel speed sensor at each wheel. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BTechnician A says that most ABS units are non-integral. Technician B says that some ABS are disabled (do not function) below about 5 mph (8 km/h). Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BWhich type of antilock braking system (ABS) requires the use of four wheel speed sensors? One channelTwo channelThree channel Four channel XTechnician A says that ABS brakes are designed to help maintain steering control during heavy braking. Technician B says that the ABS dash warning lamp is amber. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BThe faster a wheel rotates, the higher the frequency produced by a wheel speed sensor. True XFalseTechnician A says that some wheel speed sensors are enclosed in a wheel bearing assembly. Technician B says that some wheel speed sensors are exposed to possible damage from road debris. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor B CHAPTER 15ABS Diagnosis and ServiceANSWERS TO REVIEW QUESTIONS:Describe the proper operation of the red and amber brake warning lamps. The red brake warning lamp should be on if there is a hydraulic brake failure, low brake fluid or if the parking brake is on. The amber ABS lamp is on during a pre-test after start up and if the electronic brake controller detects a fault in the antilock brake system.List the items that should be checked as part of a thorough visual inspection. The items that should be checked as part of a thorough visual inspection include:Brake fluid level and conditionBrake fluid leaksFuses and fusible linksWiring and electrical connectionsWheel speed sensorsBase brake componentsWheels and tiresParking brake operationExplain how to retrieve a diagnostic trouble code from a General Motors vehicle equipped OBD-II.A factory scan tool or an enhanced factory level scan tool will be needed to retrieve ABS diagnostic trouble codes (DTCs). The Tech 2, Tech2Win, or GDS2 can be used, depending on the vehicle.Describe how to use a multimeter to check for proper wheel speed sensor operation. The multimeter (DVOM) is used to check the sensor resistance and AC voltage output.ANSWERS TO CHAPTER QUIZ:The red brake warning lamp is on and the amber ABS lamp is off. Technician A says that a fault is possible in the base brake system. Technician B says that the red brake warning lamp can be turned on by a low brake fluid level in the master cylinder. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTwo technicians are discussing magneto-type wheel speed sensors. Technician A says that wheel speed sensors are magnetic. Technician B says that the toothed sensor ring is magnetic. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BTechnician A says that using the space-saving small spare tire may trigger an ABS amber warning lamp. Technician B says the use of the small spare tire may trigger the red brake warning lamp. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BTechnician A says that, with some antilock braking systems, the diagnostic trouble code may be lost if the ignition is turned off before retrieving the code. Technician B says that some antilock braking systems require that a terminal be grounded to cause the amber ABS warning lamp to flash diagnostic trouble codes. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTechnician A says that a scan tool may be required to retrieve data and diagnostic trouble codes from some antilock braking systems. Technician B says that the GDS2 diagnostic system is used on 2008 and older vehicles. Which technician is correct? Technician A onlyXTechnician B onlyBoth Technicians A and B Neither Technician A nor BTechnician A says that a breakout box is sometimes required to diagnose an antilock braking system. Technician B says that a breakout box requires the use of a digital multimeter. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTechnician A says that a noise or vibration may be sensed by the driver when the ABS performs a self test. Technician B says that the ABS fuse may have to be removed to erase some ABS diagnostic codes if a scan tool is not used. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BThe ABS computer uses what signal characteristic from a wheel speed sensor? a. ?Voltageb.? Frequency Xc.? Resistanced.? ElectromagneticMost passive wheel speed sensors should measure how much resistance? a. 800 to 1,400 ohms Xb. 100 to 300 ohmsc. 1 to 3 ohmsd. 0.1 to 1 ohmTechnician A says that a pocket magnet can be used to clean metal debris off of the encoder ring. Technician B says that an active WSS delivers a 7 to 14 mA signal to the EBCM. Which technician is correct?Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BCHAPTER 16Regenerative Braking SystemsANSWERS TO REVIEW QUESTIONS:What is inertia? Inertia is the kinetic energy of a moving object that resists being put into motion and has a tendency to remain in motion unless acted on by an outside source.What is the difference between series and parallel regenerative braking systems? In a series regenerative braking system, the amount of regeneration is proportional to the brake pedal position. In a parallel regenerative braking system, the base brakes are used along with regenerative braking and are proportional to vehicle speed rather than brake pedal position.What happens in the regenerative braking system when the high-voltage batteries are fully charged? If the batteries are charged to the specified maximum and braking occurs on a vehicle equipped with regenerative brakes, the braking forces from the base brakes are used to slow and/or stop the vehicle. Describe what occurs when the driver first releases the accelerator pedal and then starts to brake on a hybrid electric vehicle equipped with regenerative braking. When the driver releases the accelerator pedal, regenerative braking is being used to slow the vehicle slightly. When the brake pedal is depressed, the brake forces increase in proportion to the distance and pressure applied to the brake pedal by the driver.ANSWERS TO CHAPTER QUIZ:Which type of regenerative braking system uses an electro hydraulic system? Series XParallelBoth series and parallelNeither series nor parallelKinetic energy is______________. The energy that the driver exerts on the brake pedalThe energy needed from the batteries to propel a vehicleThe energy in any moving object XThe energy that the motor produces to propel the vehicleInertia is________________. The energy of any moving object that has mass (weight) XThe force that the driver exerts on the brake pedal during a stopThe electric motor force that is applied to the drive wheelsThe force that the internal combustion engine and the electric motor together apply to the drive wheels during rapid accelerationTechnician A says that the Hybrid Powertrain Control Module (HPCM) can almost instantly change the drive motor into a generator in a hybrid electric vehicle. Technician B says that the HPCM can control the electric motors by varying the frequency of the applied current. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BDuring braking on a hybrid electric vehicle equipped with regenerative braking system, what occurs when the driver depresses the brake pedal? The friction brakes are only used as a backup and not used during normal braking.The motors become generators. XThe driver needs to apply a braking lever instead of a depressing the brake pedal to energize the regenerative braking system.The batteries are charged to 100 percent SOC.Technician A sys that a front-wheel-drive hybrid electric vehicle can only generate electricity during braking from the front wheel motor(s). Technician B says that the antilock braking (ABS) is not possible with a vehicle equipped with a regenerative braking system. Which technician is correct? a. Technician A only Xb. Technician B only c. Both Technicians A and B d. Neither Technician A nor BIn a regenerative braking system, which part of the electric motor is being controlled by the computer? The rotorThe stator XBoth the rotor and the statorNeither the rotor nor the statorIn a Two-Mode regenerative braking system, how many pressure sensors are used? OneTwoThreeFour XHow many secondary pistons are contained in the Chevrolet Volt master cylinder? OneTwo XThreeFourTwo technicians are discussing deceleration rates. Technician A says that a one “g” stop is a gentle slowing of the vehicle. Technician B says that a stopping rate of 8 ft./sec2 is a severe stop. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor B XCHAPTER 17Electronic Stability Control SystemsANSWERS TO REVIEW QUESTIONS1. What is the difference between oversteering and understeering? Oversteering means that the rear wheels loose traction and the vehicle can spin out of control. Understeer means that the vehicle tends to continue traveling straight when turning a corner.2. What is the “sine with dwell” test? A type of test performed to verify that the electronic stability control system (ESC) can operate correctly and keep the vehicle under control.3. What are some of the other names used to identify an electronic stability control (ESC) system? Some of the names include: Stabilitrak; Electronic Stability Program (ESP); Vehicle stabilityEnhancement system (VSES); electronic stability control (ESC).4. What sensors are used in the electronic stability control system? The sensors used in most Electronic Stability Control (ESC) systems include the steering wheel (handwheel) sensor; Vehicle Speed (VS) sensor; lateral acceleration sensor; and yaw rate sensor.5. What action does the traction control system perform to help the drive wheels maintain traction during acceleration? The controller performs some or all of the following to help restore drive wheel traction during acceleration:Retard ignition timing to reduce engine torqueDecrease the fuel injector pulse-width to reduce fuel delivery to the cylinder to reduce engine torque.Reduce the amount of intake air if the engine is equipped with an electronic throttle control (ETC). Reduced airflow will reduce engine torque.Up-shift the automatic transmission/transaxle. If the transmission is shifted into a higher gear, the torque applied to the drive wheels is reduced.Apply individual wheel brakes to slow or stop the wheel from spinning.6. What is the typical diagnostic procedure to follow when troubleshooting a fault with the electronic stability control or traction control system? The procedure usually specified by vehicle manufacturers for diagnosing ESC or TC concerns involves the following steps:Step 1Verify the customer concern (complaint).Step 2 – Perform a thorough visual inspecting.Step 3 – Check service information for the specified procedure to follow.Step 4 – Follow the troubleshooting procedure as specified to fix the root cause of the problem.Step 5 – Repair the fault.Step 6 – Road test the vehicle under the same conditions that were performed to verify the fault to verify the repair.ANSWERS TO THE CHAPTER QUIZ:The electronic stability control (ESC) system requires that the vehicle be equipped with what type of brake system? a. Four-wheel disc brakesb. Four channel ABS Xc. Three channel ABSd. Front disc with rear drum brakesWhich Federal Motor Safety Standard requires electronic stability control to be on all vehicles by 2011? a. 126 Xb. 113c. 109d. 101What is the name of the standard test that is performed to verify ESC operation? a. ESC plusb. Vehicle stability enhancement testc. Sine with dwell Xd. Anti-skid testWhat other name is used to describe an electronic stability control (ESC) system? a. Stabilitrakb. Electronic Stability Program (ESP)c. Vehicle Stability Enhancement System (VSES)d. Any of the above XWhich sensor is used by the ESC controller to determine the driver’s intended direction? a. Yaw sensorb. Steering wheel (hand wheel) position sensor Xc. Vehicle speed (VS) sensord. Lateral acceleration sensorA diagnostic trouble code (DTC) has been set for a fault with lateral acceleration sensor or circuit. What test could be performed to check if the sensor is working? a. Unplug it and see if the scan tool reads 1.0 Gb. Unbolt it and hold the sensor sideways to see if a scan tool reads 0.0 Gc. Unbolt it and hold the sensor sideways to see if a scan tool reads 1.0 G Xd. Drive the vehicle in a circle to see if the scan tool reads 0.0 GA lateral acceleration sensor is usually located where in the vehicle? a. Under the front seatb. In the center consolec. On the package shelfd. Any of the above locations XIf a vehicle tends to continue straight ahead while cornering, the condition is called _____.a. Understeerb. Plowingc. Tightd. All of the above XTraction control uses the antilock braking system and other devices to limit __________ of the drive wheels during acceleration. a. Positive slip Xb. Negative slipA traction control system can often control all except ___________. a. Limit engine torque delivered to the drive wheelb. Engage four-wheel drive Xc. Upshift the automatic transmissiond. Apply the wheel brake to the wheel that is losing tractionCHAPTER 18Tires and WheelsANSWERS TO REVIEW QUESTIONSList the various parts of a tire and explain how a tire is constructed. The parts of a tire include the body and belt plies, bead, sidewall, inner liner, and tread rubber. A tire builder assembles the inner liner and body plies around the beads before assembling it together with the belt and tread. After the tire is assembled, it is placed in a press where high temperature and chemical reaction cure the rubber and the sidewall and tread designs are formed.What is meant by the “aspect ratio” of a tire? The aspect ratio is the percent of the height of the tire from bead to tread to the cross-sectional width of a tire. A 70 series (70% as high as it is wide) will ride smoother than a 50 series tire because the sidewalls are higher and can better absorb road shocks and bumps. The shorter sidewall height of a 50 series tire, however, provides a stiffer, better handling tire.List the factors that should be considered when purchasing tires. Tire purchasing guidelines include: purchase the same type and size of tire and no wider or narrower than 10 mm from the original; it is best to purchase all four tires at the same time so that rotating the tires is not a problem.Explain the three major areas of the Uniform Tire Quality Grading System. The three major areas of the uniform tire quality grading system include tread wear, traction and temperature resistance.How is the proper tire inflation pressure determined? The proper tire inflation pressure can be determined by checking the recommended tire pressure as specified by the vehicle manufacturer and inflating to no more than the maximum pressure stated on the tire sidewall.ANSWERS TO CHAPTER QUIZThe part of the tire that is under just the tread of a radial tire is called the _____________. BeadBody (carcass) plyBelt XInner linerThe aspect ratio of a tire means _______________________. Its width to diameter of a wheel ratioThe ratio of height to width XThe ratio of width to heightThe ratio of rolling resistanceA tire is labeled 215/60R × 15 92T; the T indicates ________________. Its speed rating XIts tread wear ratingIts load ratingIts temperature resistance ratingThe 92 in the tire designation in question 3 refers to the tire's _______________. Speed ratingTread wear ratingLoad rating XTemperature resistance ratingRadial tires can cause a vehicle to pull to one side while driving. This is called “radial tire pull” and is often due to the __________________. The angle of the body (carcass) pliesTire conicity XTread designBead designTire inflation is very important to the safe and economical operation of any vehicle. Technician A says that the pressure should never exceed the maximum pressure imprinted on the sidewall of the tire. Technician B says to inflate the tires to the pressures recommended on the tire information decal or placard on the driver’s door. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BWhen purchasing replacement tires, do not change tire width from the stock size by more than _____________. a. 10 mm X b. 15 mm c. 20 mm d. 25 mmWhat do the letters JJ mean in a wheel designation size labeled 14 × 7JJ? The offset of the rimThe bolt circle codeThe back spacing of the rimThe shape of the flange area XTechnician A says that a PAX run-flat tire uses a special wheel. Technician B says that a standard tire can be used to replace a PAX run-flat tire. Which technician is correct? a. Technician A only Xb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor BWheel back spacing is also called________. Rear spacing XPositive offsetNegative offsetOffsetCHAPTER 19Tire Pressure Monitoring SystemsANSWERS TO REVIEW QUESTIONS1. How does the use of wheel speed sensors detect a tire with low inflation pressure? A low tire will rotate faster than a properly inflated tire and this difference can be detected by the wheel speed sensors.2. What is the difference between faults when the TPMS warning lamp is on compared with when it is flashing? A flashing TPMS warning light indicates that a fault has been detected. If the TPMS warning lamp is on, this means that low tire pressure has been detected.3. What is the percentage of vehicles that each vehicle manufacturer must equip with TPMS? 100% of all 2008 and newer vehicles must be equipped with direct reading TPMS system. Earlier vehicles were phased in starting with 2004 model year vehicles.4. TPMS pressure sensors can be made by what manufacturer? BeruLearPacificSchraderSiemensTRW5. What are the three modes of sensor operation? The three modes of operation include the Active mode, Sleep mode and Alert mode.6. What information is sent to the TPMS controller from the sensor? The information sent from the TPMS sensor to the controller includes senor identification, tire inflation pressure, air temperature (some sensors) and battery voltage of the sensor (some sensors).After removing a stem-type pressure sensor to replace a tire or perform a tire repair, what should be replaced? Whenever a stem-type TPMS sensor is replaced the following items should also be replaced:valve cap, valve core (nickel plated only), nut and grommet.ANSWERS TO CHAPTER QUIZA tire with lower than specified inflation pressure could lead to what condition? a. Reduced fuel economyb. Reduced tire lifec. Increased changes of roadside faults or accidentsd. All of the above XWhich tire inflation information should be checked to determine the proper tire inflation pressure? a. Cold placard inflation pressure Xb. The maximum pressure as stated on the sidewall of the tirec. 32 PSI in all tiresd. Any of the aboveTwo technicians are discussing tire pressure and temperature. Technician A says that tire pressure will drop 1 PSI for every 10 degrees drop in temperature. Technician B says that the tire pressure will increase as the vehicle is being driven. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTwo technicians are discussing the indirect tire-pressure monitoring system. Technician A says that it was used by some vehicle manufacturers on vehicles before the 2008 model year. Technician B says that it uses the speeds of the RF and LR tires and compares the rotating speeds of the LF and RR tires to detect a low tire. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BThe FMVSS 138 law requires that the driver be notified if the tire inflation pressure drops how much? a. 30%b. 25% Xc. 20%d. 15%The two basic types of direct TPMS sensors include ________. a. Rubber stem and aluminum stemb. Beru and Schraderc. Stem-mounted and banded Xd. Indirect and directWhat mode does a direct pressure sensor enter when the vehicle is stopped? a. Sleep mode Xb. Storage modec. Alert moded. Active modeTo activate or learn a direct pressure sensor, what does the service technician need to do? a. Enter learn mode and use a magnetb. Enter learn mode and decrease inflation pressurec. Use a handheld testerd. Any of the above depending on the vehicle and system XWhat does the “delta pressure method” mean? a. Change the inflation pressure Xb. Activate the sensor so it broadcasts the pressure to the scan toolc. Inflating the tire to the specified pressured. Using a handheld tester to read the pressure as reported by the sensorWhat type of valve core is used in stem-mounted sensors? a. Brassb. Nickel plated Xc. Steeld. AluminumCHAPTER 20Tire and Wheel ServiceANSWERS TO REVIEW QUESTIONSList the precautions and recommendations regarding tire selection and maintenance. The precautions and recommendations regarding tire selections and maintenance include: maintaining correct tire pressures, avoiding overloading the vehicle, keeping the tires balanced and rotated regularly.Determine the proper wheel mounting torque for your vehicle from the guidelines provided. The proper wheel mounting torque for your vehicle can be found in the owner’s manual or in service information for your vehicle. Describe how to check for lateral and radial runout of the wheels and tires. Radial runout checks that the wheel and tire are round. Lateral runout checks for side-to-side movement that can cause a vibration. Both are checked with the wheels off the ground and using a dial gauge.Describe the difference between static and dynamic balance. Static balance is balancing in one plane or direction. Static balance does not account for any "wobble" or imbalance inside or outside of a tire/wheel assembly. Dynamic balance is balancing in two planes and accounts for imbalance both radially and laterally.ANSWERS TO CHAPTER QUIZA tire is worn excessively on both edges. The most likely cause of this type of tire wear is _____________. OverinflationUnderinflation XExcessive radial runoutExcessive lateral runoutWhen seating a bead of a tire, never exceed _______ PSI. 3040 X5060For best tire life, most vehicle and tire manufacturers recommend tire rotation every______. 3,000 miles7,500 miles X9,000 miles12,000 milesWhat lubricant should be used when mounting a tire? Silicone sprayGreaseWater-based soap XSAE 10W-30 engine oilUsing the modified X-method of tire rotation on a front-wheel-drive vehicle, where should be the left front wheel be placed? Right frontRight rearLeft rear XKept at the left frontWhich statement is false? Excessive radial runout can cause a tramp-type vibration.Excessive lateral runout can cause a tramp-type vibration. XA tire out of balance dynamically can cause a shimmy-type vibration.A tire out of balance statically can cause a tramp-type vibration.The recommended type of wheel weight to use on aluminum (alloy) wheels is _________. Lead with plated spring steel clipsCoated (painted) or stick on lead weights XLead weights with longer-than-normal clipsAluminum weightsMost vehicle and tire manufacturers recommend that no more than _____ ounces of balance weight be added to a wheel/tire assembly. 2.53.54.55.5 XA vehicle vibrates at highway speed. Technician A says that water in the tire(s) could be the cause. Technician B says that an out-of-round tire could be the cause. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor B Proper tire inflation pressure information is found _______________. On the driver’s door or postIn the owner’s manualOn the sidewall of the tireBoth a and b XCHAPTER 21Wheel Bearings and ServiceANSWERS TO REVIEW QUESTIONS:List three common types of automotive antifriction bearings. Three types of automotive antifriction bearings include: ball bearings, roller bearings, and tapered roller bearings.Explain the adjustment procedure for a typical tapered roller wheel bearing. The adjustment procedure for a typical tapered roller wheel bearing includes: tightening the spindle nut while rotating the wheel, then loosening the nut (while still rotating the wheel), tighten the spindle nut by hand. Install the cotter key.List four symptoms of a defective wheel bearing. A defective wheel bearing usually makes a sound like a noisy tire (growl or wobble). Additional symptoms include noise, vibration, and roughness felt in the steering wheel.Describe how the rear axle is removed from a C-lock-type axle. The differential cover and pinion shaft have to be removed before allowing access to the c-clip (lock), which holds the rear axle in place.ANSWERS TO CHAPTER QUIZ:Which type of automotive bearing can withstand radial and thrust loads, yet must be adjusted for proper clearance? Roller bearingTapered roller bearing XBall bearingsNeedle roller bearingMost sealed bearings used on the front wheels of front-wheel-drive vehicles are usually which type? Roller bearingSingle tapered roller bearingDouble row ball bearing XNeedle roller bearingOn a bearing that has been shock loaded, the race (cup) of the bearing can be dented. This type of bearing failure is called ___________________. SpallingArcingBrinelling XFlutingThe bearing grease most often specified is rated NLGI __________________. #00#0#1#2 XA non-drive-wheel bearing adjustment procedure includes a final spindle nut tightening torque of ___________. Finger tight X5 lb. in. 12 to 30 lb. ft. 12 to 15 lb. ft. plus 1/16 in. turnAfter a non-drive-wheel bearing has been properly adjusted, the wheel should have how much endplay? Zero0.001 to 0.005 in. X0.10 to 0.30 in.1/16 to 3/32 in.The differential cover must be removed before removing the rear axle on which type of axle? Retainer plateC-lock XPress fitWelded tubeWhat part(s) should be replaced when servicing a wheel bearing on a non-drive wheel? The bearing cupThe grease sealThe cotter keyBoth the grease seal and the cotter key XTechnician A says that a defective wheel or axle bearing often makes a growling or rumbling noise. Technician B says that a defective wheel or axle bearing often makes a noise similar to a tire with an aggressive mud or snow design. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B XNeither Technician A nor BTwo technicians are discussing differentials. Technician A says all differentials are vented. Technician B says that a clogged vent can cause the rear axle seal to leak. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BCHAPTER 22Suspension System Components and OperationANSWERS TO REVIEW QUESTIONSList the types of suspensions and name their component parts. Types of suspensions include coil spring, torsion bar, and leaf spring types. Most types use control arms or links to provide longitudinal (front-to-back) and transverse (side-to-side) support.Explain Hooke's Law. Hooke’s Law states that the deflection of a spring is directly proportional to the applied force.Describe the purpose and function of a stabilizer bar. A stabilizer bar is used to limit body roll during cornering.Explain the difference between a load-carrying and a friction ball joint. A load-carrying ball-joint supports the weight of the vehicle whereas a friction (follower) ball-joint acts as a pivot point for the suspension.ANSWERS TO CHAPTER QUIZThe spring rate of a spring is measured in units of ________. lb per inch Xft-lbpsiin.-lbTwo technicians are discussing torsion bars. Technician A says that many torsion bars are adjustable to allow for ride height adjustment. Technician B says that torsion bars are usually marked left and right and should not be switched side to side. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BWhat component(s) is considered to be unsprung weight? FrameBodyWheels and tires XBoth a and bTwo technicians are discussing MacPherson struts. Technician A says that in most applications the entire strut assembly rotates when the front wheels are turned. Technician B says a typical MacPherson strut suspension system uses only one control arm and one ball joint per side. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BTechnician A says that regular replacement shock absorbers will raise the rear of a vehicle that is sagging down. Technician B says that replacement springs will be required to restore the proper ride height. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BWhat suspension component is used to counteract body lean during cornering? Torsion barStrut rodStabilizer bar XControl armA center bolt is used in what type of spring? CoilLeaf XTorsion barAll of the aboveTwo technicians are discussing air shocks. Technician A says that air is forced through small holes to dampen the ride. Technician B says that air shocks are conventional hydraulic shock absorbers with an airbag to control vehicle ride height. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BThe owner of a pickup truck wants to cut the coil springs to lower the vehicle. Technician A says that the ride will be harsher than normal if the springs are cut. Technician B says that the springs could be damaged, especially if a cutting torch is used to cut the springs. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BA MacPherson strut is a structural part of the vehicle. True XFalseCHAPTER 23Front Suspension and ServiceANSWERS TO REVIEW QUESTIONSDescribe how to perform a proper road test for the diagnosis of suspension-related problems. A thorough road test should include driving the vehicle over bumpy sections of road as well as beside parked vehicles. Drive into driveways with a curb to cause the suspension to compress while the wheels are turned. A complete test drive should also include driving in reverse while turning.List four symptoms of worn or defective shock absorbers. The four symptoms of defective shock absorbers include: (a) Excessive harshness, (b) Frequent "bottoming out" on rough roads, (c) Extended vehicle vertical movement after driving on dips or a rise in the road, and (d) Cupped-type tire wearExplain the procedure for replacing front shock absorbers on an SLA-type suspension vehicle. Front shock absorber replacement on an SLA-type suspension simply requires that the fasteners be removed. No special methods or tools are required and the shocks can even be replaced without having to hoist the vehicle off the ground.Describe the testing procedure for ball joints. Load-carrying ball joints must be unloaded before they can be accurately tested. If the coil spring or torsion bar is attached to the lower control arm, then the ball joint can be unloaded by placing a jack under the lower control arm and raising the tire off the ground. A special block or tool is required to hold the control arm if the spring is attached to the upper control arm. A dial indicator and a pry bar are used to move and measure the amount of wear. Describe the correct general procedure to remove and replace tapered suspension components. Tapered suspension components, such as ball joints, can be safely separated from the attached component by using a puller-type tool. To reassemble, use a new nut and tighten to factory specifications. If the cotter key hole does not line up after the attaching nut is tightened to specifications, tighten the nut just enough to align the cotter key - never loosen the nut to align the hole.ANSWERS TO CHAPTER QUIZUnusual noise during a test drive can be caused by ___________________. Defective wheel bearings or stabilizer bar linksDefective or worn control arm bushings or ball jointsWorn or defective CV jointsAll of the above XTwo technicians are discussing non-indicator-type ball joint inspection. Technician A says that the vehicle should be on the ground with the ball joints loaded, then checked for freeplay. Technician B says that the ball joints should be unloaded before checking for freeplay. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and BNeither Technician A nor BMost manufacturers specify a maximum axial play for ball joints of about ____________. 0.003 in. (0.076 mm)0.010 in. (0.25 mm)0.030 in. (0.76 mm)0.050 in. (1.27 mm) XThe preferred method to separate tapered chassis parts is to use ____________. A pickle fork toolA torch to heat the joint until it separatesA puller tool or two hammers to shock and deform the taper XA drill to drill out the tapered partA light film of oil is observed on the upper area of a shock absorber. Technician A says that this condition should be considered normal. Technician B says that a rod seal may bleed fluid during cold weather, causing the oil film. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BBefore the strut insert can be removed from a typical MacPherson strut assembly, which operation is necessary to prevent possible personal injury? The brake caliper and/or brake hose should be removed from the strut housingThe coil spring should be compressed XThe upper strut mounting bolts should be removedThe lower attaching bolts should be removedWhat should the technician do when replacing stabilizer bar links? a. The stabilizer bar should be removed from the vehicle before replacing the links.b. The links can be replaced individually, yet the manufacturer often recommends that the links at both ends be replaced together. Xc. The stabilizer bar must be compressed using a special tool before removing or installing stabilizer bar links.d. Both b and c are correct.A noise and a pull toward one side during braking is a common symptom of a worn or defective _______________. Shock absorberStrut rod bushing XStabilizer bar linkTrack rod bushingTo help prevent vehicle wandering on a vehicle with torsion bars, the ride height should be within __________ side to side. 0.003 in. (0.076 mm)0.050 in. (1.27 mm)0.100 in. (2.5 mm)0.125 in. (3.2 mm) XTwo technicians are discussing suspension bushings. Technician A says that replacing control arm bushings usually requires special tools. Technician B says using high-performance urethane bushings may cause excessive noise to be transferred to the passenger compartment. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B X d. Neither Technician A nor BCHAPTER 24Rear Suspension and Service ANSWERS TO REVIEW QUESTIONS1. What are the disadvantages of a solid rear axle? Solid rear axles have the following disadvantages: high unsprung weight, side-to-side shock transference, and reduced tire adhesion.2. What is the purpose of a torque arm? A torque arm absorbs engine torque and reduces axle windup.3. What must be done to ensure safety when replacing the rear shock absorbers? When replacing rear shock absorbers, the rear axle must be supported by tall safety standards to prevent the rear axle from dropping when the shocks are removed.ANSWERS TO CHAPTER QUIZA vehicle equipped with a coil spring front suspension and a leaf spring rear suspension “dog tracks” while driving on a straight, level road. Technician A says that a broken center bolt could be the cause. Technician B says defective rear shock absorbers could be the cause. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BWhen axle windup is controlled by the rear-leaf spring during acceleration, this system is called ____________. Trailing armSemi-trailing armTorque arm Hotchkiss drive XA loud “bang” is heard and felt every time the accelerator is depressed or released on a rear-wheel-drive vehicle. Technician A says that a leaking shock absorber could be the cause. Technician B says a broken torque arm could be the cause. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and B Neither Technician A nor BTechnician A says that leaf springs are mounted lengthwise on the rear of many vehicles. Technician B says that some vehicles use a transversely mounted leaf spring on the rear. Which technician is correct? Technician A onlyTechnician B onlyBoth Technicians A and B XNeither Technician A nor BA strut-type suspension is used ________________. In the front onlyIn the rear onlyIn both the front and rear XIn rare vehicles no longer in productionTwo technicians are discussing rear shock absorbers. Technician A says that if one shock is leaking, then both rear shock absorbers should be replaced. Technician B says that the rear axle should be supported before removing rear shock absorbers. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B X d. Neither Technician A nor BA "witness mark" is a______. a. Type of fastener b. Type of tool c. Mark where two parts have rubbed or touched X d. Identification markThe left front of the vehicle is higher than the right front and the right rear is lower than the left rear. What is the most likely cause of this problem? a. A weak right-rear shock absorber b. A broken track rod c. A broken left-front shock absorber d. A sagging right rear spring XOne rear leaf spring is broken. Technician A says that both rear leaf springs should be replaced. Technician B says that only the broken spring needs to be replaced. Which technician is correct? a. Technician A only X b. Technician B only c. Both Technicians A and B d. Neither Technician A nor BA track rod is also called a ______. a. Panhard rod X b. Control rod c. Handing link d. Semi-independent rodCHAPTER 25Electronic Suspension SystemsANSWERS TO REVIEW QUESTIONS1. What type of sensor is usually used on electronically controlled suspensions to sense the height of the vehicle? A photo-cell-type sensor, Hall-effect or a potentiometer-type sensors are usually used to sense the height of the vehicle.2. Why is the vehicle speed sensor used as input for many electronic suspension systems? Vehicle speed and throttle position sensors are inputs to the suspension electronic control module so the suspension can be made firm during high speed operation or during rapid acceleration.3. What is a lateral accelerometer sensor and why is it used? A G-force sensor is used to measure the acceleration, braking, and cornering forces so the suspension control module can control the suspension to become firmer during rapid vehicle movements.4. Why does the output side of the suspension air compressor contain a desiccant? A desiccant is used on the outlet of the suspension air compressor to remove water from the system, which could cause rust or an inoperative suspension system in freezing weather.ANSWERS TO CHAPTER QUIZWhat type of sensor is used as a height sensor on vehicles equipped with an electronically controlled suspension? a. Hall-effectb. Photo cellc. Potentiometerd. All of the above XWhich sensors do most vehicles use if equipped with electronic suspension? a. Height sensorsb. Steering wheel position sensorsc. Lateral accelerometer sensorsd. All of the above XA lateral acceleration sensor is used to provide the suspension control module with feedback regarding ________ force. a. Cornering Xb. Accelerationc. Brakingd. All of the aboveA steering wheel position sensor is being discussed. Technician A says that the sensor is used to determine the direction the steering wheel is turned. Technician B says that the sensor detects how fast the steering wheel is turned. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor BTechnician A says that an electronic control unit (ECU) used in the suspension system is the same as that used for engine control. Technician B says that most electronically controlled suspension systems use a separate electronic control module. Which technician is correct? a. Technician A onlyb. Technician B only Xc. Both Technicians A and Bd. Neither Technician A nor BWhat type of actuator is used on electronically controlled suspensions? a. Solenoidb. Electric motorc. Either a or b Xd. Neither a nor bWhy is the typical rear load-leveling system connected to the ignition circuit? a. To keep the system active for a given time after the ignition is switched offb. To prevent the system from working unless the ignition key is onc. To keep the compressor from running for an extended period of timed. All of the above XWhich sensor can be tested by unbolting the sensor and with the ignition on, engine off (KOEO), looking at the scan tool data? a. “G” sensor Xb. Wheel speed sensorc. Vehicle speed sensord. Suspension sensorThe firm setting is usually selected by the electronic suspension control module whenever which of the following occurs? a. High speedb. Rapid brakingc. Rapid accelerationd. All of the above XWhich of the following is the least likely sensor to cause an electronic suspension fault? a. Yaw sensorb. Throttle position sensor Xc. Steering wheel position sensord. Vehicle speed sensorES OF VARIOUS ESC SYSTECHAPTER 26Steering Columns and GearsANSWERS TO REVIEW QUESTIONSWhat components are included in a typical steering column assembly? A typical steering column includes the steering shaft, universal joint, flexible coupling, and column cover.When the driver turns the steering wheel, how is the motion transferred to the front wheels through a conventional steering gear? When the driver rotates the steering wheel, the steering shaft rotates, which rotates the input gear inside the steering gear. The worm gear inside the steering gear then moves the sector gear, which is part of the pitman arm, which in turn is connected to the steering linkage.Why are recirculating balls used in the recirculating ball steering gear? Recirculating balls are used in a recirculating ball steering gear to reduce friction.What steering gear adjustments are possible on a conventional recirculating-ball-type steering gear? Worm bearing preload and sector lash are two of the adjustments possible on a conventional ball-type steering gear.What steering gear adjustments are possible on a typical rack-and-pinion steering gear? The rack support and pinion bearing preload can be adjusted on a rack and pinion steering gear assembly.ANSWERS TO CHAPTER QUIZThe circuit to the airbag inflation module is connected from the steering column to the steering wheel through what component? Slip ring and carbon brushesClockspring (coil) XMagnetic field sensorHall-effect switchWhich part in the steering column allows for changes in the angle between the upper and lower shafts? Flexible couplingColumn coverUniversal joint XCollapsible sectionThe rotation of the steering wheel causes which part to move the actual steering linkage in a conventional steering gear? a. Sector shaft b. Pitman arm X c. Worm gear d. Gear nutThe pitman shaft is also called the ________________. Sector XInputWormSplineThe driver rotates the steering wheel one-half of one revolution (180 degrees) on a vehicle equipped with a steering gear with a 20:1 gear ratio. How many degrees will the front wheels be rotated? a. 9 degrees Xb. 0.1 degreec. 90 degreesd. 11.1 degreesWhat causes a variable-ratio steering gear to be able to change the ratio as the steering wheel is turned? a. Using two or three different sector gears depending on designb. Using a variable-length pitman armc. Changing the number of teeth on the worm geard. Changing the length of the teeth on the sector gear XRecirculating steel balls are used in most conventional steering gears because they _______. a. Provide for a variable ratiob. Keep the steering wheel centeredc. Reduce friction Xd. Help provide feedback to the driver regarding the road surfaceWhich conventional steering gear adjustment should be the first performed? a. Worm bearing preload Xb. Tolerance adjustmentc. Gear mesh preloadd. Sector shaft endplayThe two rack-and-pinion steering gear adjustments include ____________________. a. Worm bearing preload and tolerance adjustmentb. Pinion bearing preload and rack support Xc. Sector shaft and stub shaft preloadd. Stub shaft endplay and sector shaft preloadOn a rack and pinion steering gear which adjustment is the last to be made?a. Pinion bearing preloadb. Rack-to-pinion gear preloadXc. Spline preload d. Rolling resistanceCHAPTER 27Steering Linkage and ServiceANSWERS TO REVIEW QUESTIONSDescribe how to perform a dry park test. A dry park test is performed with the vehicle on the ground, or on a drive-on-type lift, and the steering column unlocked. While an assistant moves the steering wheel, look and feel for any movement in the steering linkage connections.List the steering parts that should be replaced in pairs. The steering parts that should be replaced in pairs include the inner and outer tie rod ends.3. What test procedure can be used to check that the steering linkage is straight and level? A bounce test can be used to check that the steering linkage is straight and level.4. What is the difference between a wear and nonwear center link? A wear-type center link uses ball joints, whereas a non-wear-type center link uses holes where the tapered part of the ball-joint-type link is inserted.ANSWERS TO CHAPTER QUIZA “dry park” test to determine the condition of the steering components and joints should be performed with the vehicle ___________________. On level ground or a drive-on lift X On turn plates that allow the front wheels to move On a frame contact lift with the wheels off the ground Lifted off the ground about 2 in. (5 cm)Two technicians are discussing bump steer. Technician A says that an unlevel steering linkage can be its cause. Technician B says that if the steering wheel moves when the vehicle is bounced up and down, the steering linkage may be bent. Which technician is correct? Technician A only Technician B only Both Technicians A and B X Neither Technician A nor BA vehicle has an excessive amount of freeplay in the steering wheel and it is difficult to keep it traveling straight on a straight and level road. Which is the least likely cause? Worn tie rod ends Excessive play in the ball socket assemblies Worn idler arms Loose pitman arm retaining nut XHow are the inner tie rods attached to the rack on a center-take-off-type rack-and-pinion steering gear? Staked Bolted X Riveted PinnedWhat is the most likely cause of bump steer? Worn outer tie rod ends A worn center link Worn or oil-soaked rack bushings X A lack of proper lubrication of all ball-and-socket jointsHow much endplay is usually acceptable in tie rod ends? Zero X 0.0010 to 0.030 in. 0.030 to 0.050 in. 0.050 to 0.100 in.Technician A says that outer tie rod ends should be replaced in pairs, even if only one is worn. Technician B says that inner tie rod ends should be replaced in pairs, even if only one is worn. Which technician is correct? Technician A only Technician B only Both Technicians A and B X Neither Technician A nor BWhich tool is not recommended to be used to separate tapered steering components because it can do harm? Taper breaker Pickle fork X Tie rod removal puller Two hammersTechnician A says that torque prevailing nuts can be reused unless damaged. Technician B says that a new cotter key should always be used. Which technician is correct? Technician A only Technician B only X Both Technicians A and B Neither Technician A nor BNew tie rods are being installed. Technician A says to tighten the retaining nuts to specification and then loosen, if needed to align the cotter pin hole. Technician B says to tighten further to align the cotter key hole. Which technician is correct? Technician A only Technician B only X Both Technicians A and B Neither Technician A nor B CHAPTER 28Power-Assisted Steering Operation and ServiceANSWERS TO REVIEW QUESTIONSList five possible causes for hard steering. Five possible causes of hard steering include:a. Too tight an adjustment of the rack bushing or over-center adjustmentb. Under-inflated tiresc. Internal steering gear mechanical bendingd. Loose, worn or defective power steering pump drive belte. Low or contaminated power steering fluidExplain the procedure for flushing a power steering system. Flushing a power steering system includes the following steps:Step 1 - Remove the low pressure hose from the pump (plug fitting) and direct the return line to an empty container. With the front wheels off the ground, fill the power steering pump reservoir and start the engine.Step 2 - As the old power steering fluid is being pumped into the container, keep the reservoir full of clean fluid as an assistant turns the steering wheel.Step 3 - When the fluid is clean going into the container, stop the engine and reconnect the low pressure line to the pump. Describe how to pressure test a power steering system. Connect the pressure tester hoses to the power steering system following the manufacturer’s instructions. Start the engine and close the shut off valve for a maximum of 15 seconds and observe the maximum pressure. Open the shutoff valve and then repeat the test checking to see if the maximum pressures are all the same. Check service information for the procedures to follow if the pressures are not within specifications.Briefly describe adjustment and service procedures for a power rack-and-pinion steering unit. Lock the steering wheel, remove the tie rod ends from the steering knuckle; disconnect the steering shaft from the steering gear stub shaft; disconnect the hydraulic lines and any wiring connectors. Lower the subframe and remove the rack mounting bolts. Remove the rack and pinion assembly from the side of the vehicle.ANSWERS TO CHAPTER QUIZTwo technicians are discussing the proper procedure for bleeding air from a power steering system. Technician A says that the front wheels of the vehicle should be lifted off the ground before bleeding. Technician B says that the steering wheel should be turned left and right with the engine off during the procedure. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B X d. Neither Technician A nor BA power steering pressure test is being performed, and the pressure is higher than specifications with the engine running and the steering wheel stationary in the straight-ahead position. Technician A says that a restricted high-pressure line could be the cause. Technician B says that internal leakage inside the steering gear or rack-and-pinion unit could be the cause. Which technician is correct? a. Technician A only Xb. Technician B onlyc. Both Technicians A and B d. Neither Technician A nor BWhen pressure testing an hydraulic assisted power steering system, the highest pressures were greater than 50 PSI of each other. This indicates a problem with_____. a. Pump rotorb. Pump vanesc. Flow control valve Xd. Defective hoseIntegral power steering gears use _____________ for lubrication of the unit. SAE 80W-90 gear lubeChassis grease (NLGI #2)Power steering fluid in the system XMolybdenum disulfideWhat can cause hard steering on a vehicle equipped with hydraulic power assisted steering system? a. Low tire pressureb. Slipping P.S. pump drive beltc. Low or contaminated power steering fluidd. Any of the above XHigh-pressure hoses have to be used on the high-pressure side of the power steering system because pressures can reach as high as _________. a. 200 PSIb. 750 PSIc. 1,500 PSI Xd. 2,500 PSISome vehicles are equipped to signal the computer whenever the power steering pressures increase so that the idle speed can be increased to prevent stalling during turns at low speeds. What component signals the computer? a. Pressure-relief valve b. Power steering pressure switch Xc. Rotary valved. Flow control valveWhat type of motor is used in most electric power steering (EPS) systems? a. AC brush typeb. DC brushless Xc. Stepper d. DC capacitor startElectronically controlled variable-assist power steering systems vary the amount of boost by __________. a. Varying the pump output orifice size Xb. Speeding up or slowing down the power steering pumpc. Changing the flow of fluid through the steering geard. Bypassing some of the fluid back into the reservoirTwo technicians are discussing electric power steering (EPS) systems. Technician A says that some systems operate on 12 volts. Technician B says that some systems operate on 42 volts such as some hybrid electric vehicles. a. Technician A only b. Technician B onlyc. Both Technicians A and B Xd. Neither Technician A nor B CHAPTER 29Wheel Alignment PrinciplesANSWERS TO REVIEW QUESTIONSExplain the three basic alignment angles of camber, caster, and toe. Camber is the tilt of the wheel from true vertical as viewed from the front or rear of the vehicle.Caster is the forward or rearward tilt of the steering axis. Toe is the difference in distance between the front and rear of the tires.Describe what happens to tire wear and vehicle handling if toe, camber, and caster are out of specification or not equal side-to-side. If toe is incorrect, excessive tire wear occurs. If toe is unequal side to side, the steering wheel will notbe straight when the vehicle is driven straight on a level road. Camber can cause a pull if unequalside to side and tire wear if out of specification. Caster can cause a pull only if the caster is different side to side.Explain how knowing SAI, TOOT, and included angle can help in the correct diagnosis of an alignment problem. SAI, TOOT and included angle are all considered to be diagnostic angles. Bent or damaged chassis parts are the result of angles not within specification and must be corrected to assure a proper alignment.Explain what thrust angle means. Thrust angle is the total toe angle of the rear wheels.ANSWERS TO CHAPTER QUIZWhen performing an alignment, which angle is the most important for tire wear? Toe XCamberCasterSAI (KPI)Positive camber means_______. a. The top of the tire is tilted outward at the top. Xb. The top of the tire is tilted inward at the topc. The fronts of the tires on the same axle are closer together at the front than the reard. Either a or bWhich alignment angle is adjustable on all vehicles? CamberCasterToe XSAI (KPI)Positive (+) toe is ________________________. Toe-in XToe-outIf the top of the steering axis is tilted 2 degrees toward the rear of the vehicle, this is _________. Positive camberNegative camberNegative casterPositive caster XA steering dampener may be needed to reduce shimmy on vehicles that have high positive_____. a. Camberb. Caster Xc. Toed. Included angleIf the turning radius (toe-out on turns, or TOOT) is out of specification, what part or component is defective? The strut is bent.The steering arm is bent. XThe spindle is bent.The control arm is bent.Which angle determines the thrust angle? Front toeRear toe XRear camber d. Front caster, SAI, and included angleIncluded angle is ______. a. SAI + casterb. Camber + casterc. Camber + SAI Xd. Toe + camberTwo technicians are discussing scrub radius. Technician A says that scrub radius cannot be measured. Technician B says that scrub radius cannot be adjusted. Which technician is correct? a. Technician A onlyb. Technician B onlyc. Both technicians A and B Xd. Neither technician A nor B CHAPTER 30Alignment Diagnosis and ServiceANSWERS TO REVIEW QUESTIONSList 10 prealignment checks that should be performed before the wheel alignment is checked and/or adjusted. Ten pre-alignment inspections include the following items:a. Tire pressuresf. Ride heightb. Wheel bearingsg. Steering gear loosenessc. Tie rod endsh. Control arm bushingsd. Center linksi. Idler arm e. Stabilizer bar links and bushings j. Excessive or unequal loadsDescribe the difference between a lead (drift) and a pull. A pull is a condition that causes a definite "tug" on the steering wheel toward one side while driving straight on a level road. A lead or drift is the movement of a vehicle toward one side when the driver's hands are temporarily removed from the steering wheel, but is not enough to cause corrective counter steering pressure.Explain the causes and possible corrections for torque steer. Torque steer is the pulling of a vehicle during acceleration only on a front-wheel drive vehicle. If severe, the technician should carefully inspect and replace, if necessary, the engine and/or transaxle mounts or any other component that has failed to keep the engine and drive train level.Explain the causes and possible corrections for memory steer. Memory steer is usually caused by binding in the steering or suspension system. By disconnecting the tie rods from the steering knuckles, a technician can check to see if the front wheels rotate through their steering axis smoothly. To prevent "installing" a memory steer into a vehicle, all steering and suspension components should be tightened only after the vehicle is on the ground with the wheels in the straight ahead position.List the necessary steps to follow for a four-wheel alignment. A proper four-wheel alignment should be done in the following sequence: rear camber, rear toe, front caster and camber, then front toe.ANSWERS TO CHAPTER QUIZIf the tie rod ends become worn, which angle is most affected? a. Camberb. Casterc. Toe Xd. SAI Technician A says that a vehicle will pull (or lead) to the side with the most camber (or least negative camber). Technician B says that a vehicle will pull (or lead) to the side with the most positive caster. Which technician is correct? Technician A only XTechnician B onlyBoth Technicians A and BNeither Technician A nor BTechnician A says that the front toe determines the thrust angle. Technician B says that the rear toe angle determines the thrust angle. Which technician is correct? Technician A onlyTechnician B only XBoth Technicians A and B Neither Technician A nor BStrut rods, if they are adjustable, can be used to adjust which angle? ToeCamberCaster XToe-out on turnsIf metal shims are used for alignment adjustment in the front, they adjust _____________. CamberCasterToeBoth a and b XWhich angle is largest?0.55 degrees? degree45 minutes X? degreeUse the following information to answer question 7:Specifications: Min. Preferred Max. Camber (degree) 0 1.0 1.4 Caster (degree) .8 1.5 2.1 Toe (degree) .10 .06 .15 Results: L R Camber (degree) .1 .6 Caster (degree) 1.8 1.6 Toe (degree) 1.12 +.12The vehicle above will ____________________________. Pull toward the right and feather-edge both tires XPull toward the leftWear the outside of the left tire and the inside of the right tire d. None of the aboveUse the following information to answer questions 8 and 9: Specifications: Min. Preferred Max. Camber (degree) 1/4 +1/2 1 Caster (degree) 0 +2 +4 Toe (inch) 1/16 1/16 3/16 Results: L R Camber (degree) 0.3 0.1 Caster (degree) 3.6 1.8 Toe (inch) .16 +.32The vehicle above will _________________________. Pull toward the leftPull toward the right XWanderLead to the left slightlyThe vehicle above will _________________________. WanderWear tires, but will not pullWill pull, but not wear tires XPull toward the left and cause feather-edge tire wearWhich alignment angle is most likely to need correction and cause the most tire wear? a. Toe XCamberCasterSAI/KPICHAPTER 31Vibration and Noise Diagnosis and CorrectionANSWERS TO REVIEW QUESTIONSDescribe how you can tell if the source of a vibration is at the front or the rear of a vehicle during a test drive. If the driver feels the vibration in the steering wheel or sees the hood or dash vibrate, the cause is usually due to front wheels or tires. If the vibration is felt in the seat of the pants or the entire vehicle seems to be vibrating, the cause is usually due to rear wheels or tires or drive shaft, if rear-wheel drive.Explain the terms cycle and Hertz.The number of times a complete motion cycle takes place during a period of one second is called frequency and is measured in Hertz (Hz), formerly called cycles per second.List two types of frequency-measuring instruments.Two commonly used instruments to measure frequency are the reed tachometer and the electronic vibration analyzer (EVA).Discuss why the balance of a drive shaft on a rear-wheel-drive vehicle is more important than the balance of a front-wheel-drive axle shaft. The balance of a drive shaft is more important on a rear-wheel drive vehicle because the drive shaft rotates about three times faster than the drive wheels because of the gear reduction that occurs in the differential. On a front-wheel drive vehicle, the drive axle shafts revolve at the same speeds as the drive wheels. The lower speed makes balancing less critical.Explain how to check and balance a drive shaft on a rear-wheel-drive vehicle.A drive shaft should be checked for runout using a dial indicator at three locations along the length of the drive shaft. A strobe balancer can be used to locate the heavy part of a drive shaft and stainless steel hose clamps can be used to balance the shaft.ANSWERS TO CHAPTER QUIZA vibration that is felt in the steering wheel at highway speeds is usually due to __________. Defective or out-of-balance rear tiresDefective or out-of-balance front tires XOut-of-balance or bent drive shaft on a RWD vehicled. Out-of-balance drive axle shaft or defective outer CV joints on a FWD vehicleA vibration during braking is usually caused by ________________. Out-of-balance tiresWarped front brake rotors XA bent wheelAn out-of-balance or bent drive shaftThe rolling circumference of both tires on the same axle of a four-wheel-drive vehicle should be within ____________________. 0.1 in. (2.5 mm)0.3 in. (7.6 mm)0.6 in. (15 mm) X1.2 in. (30 mm)The maximum allowable drive shaft runout is ________________. 0.030 in. (0.8 mm) X0.10 in. (2.5 mm)0.50 in. (13 mm)0.015 in. (0.4 mm)A drive shaft can be checked for proper balance by marking the circumference of the shaft in four places and running the vehicle drive wheels to spot the point of imbalance using a __________.Reed tachometerStrobe light X Electronic vibration analyzer (EVA)Scan toolA defective clutch release (throw-out) bearing is usually heard when the clutch is ________. Engaged in neutralDisengaged in a gearDepressed to take up any freeplay XEngaged in first gear or reverseWheel-tire imbalance is the most common source of vibrations that occur in what frequency range?5-20 Hz X20-50 Hz50-100 Hz100-150 HzDrive line vibrations due to a bent or out-of-balance drive shaft on a rear-wheel-drive vehicle usually produce a vibration that is __________________.Felt in the steering wheelSeen as a vibrating dash or hoodFelt in the seat or all over the vehicle XFelt by the rear passengers onlyRubber is used for exhaust system hangers because the exhaust system gets longer as it gets hot and rubber helps isolate noise and vibration from the passenger compartment.True XFalseA vibration is felt in the steering wheel during braking only. A common cause of the vibration is ____________________.Worn idler armOut-of-balance front tiresLoose or defective wheel bearing(s)Warped or nonparallel front disc brake rotors X ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download