ARCAT, Inc.

 SECTION 11 19 00DETENTION FURNITUREDisplay hidden notes to specifier. (Don't know how? Click Here) Copyright 2014 - 2015 ARCAT, Inc. - All rights reserved** NOTE TO SPECIFIER ** PSI LLC; Prison Equipment products..This section is based on the products of PSI LLC, which is located at:2323 N. 2nd St.Minneapolis, MN 55411Tel: 612-789-0925Fax: 612-789-0196Email: request info (sales@)Web: [ Click Here ] for additional information.PSI LLC has designed, supplied, and manufactured steel and stainless steel equipment and industrial-use furnishings since 1985. We offer a complete line of Access Doors, Pass Thrus, Tables, Benches, Stools, Desks, Cabinets, Shelves, Grab bars, and additional Accessories. We specialize in custom manufacturing any of our products to meet the unique needs of your facility.Our products are high-quality, custom-made steel and stainless steel furnishings, equipment, and accessories designed for use in Hospitals, Clinics, Institutions, Schools, Cafeterias, Municipalities, Libraries, Parks & Recreation Departments, Hotels, Casinos, Restaurants, Food Service, Food Preparation, Oil Rig and Drilling Sites, Industrial and Manufacturing, Waste Management, Water Treatment, Home and Office, Television and Film props, Sports and Exercise facilities, Military and Military Contractors, Homeless shelters, Charity Organizations, Airports, Nuclear, Coal, Natural Gas Power Plants, Medical Research Facilities, and Clean Rooms.Our products are custom-made to meet your specifications including including wood tops and all stainless steel construction, as well as laser cutting and laser etching, and finishes in powder coating, painting, and chemical treatment (stainless steel only) available. Our experienced engineering department is ready to assist you in fitting our products to your facility or designing products that meet the strength, safety and security standards you are looking for. Contact PSI today for more information about custom made steel & stainless steel furnishings, equipment, and accessories!

GENERAL

SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

Tables and Seating.

Accessories.

Cabinets and Lockers.

Doors and Access Points.

Bunks.

Desks.

Shelving.

RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

Section 04 20 00 - Unit Masonry.

Section 05 40 00 - Cold-Formed Metal Framing.

Section 06 10 00 - Rough Carpentry.

Section 07 91 26 - Joint Fillers.

Section 09 26 13 - Gypsum Veneer Plastering.

REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

ASTM A 123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products.

ASTM A 167 - Stainless and Heat-Resisting Chromium-Nickel Steel Plate.

ASTM A 283/283M - Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates.

ASTM A 307 - Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength.

ASTM A 325 - Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength.

ASTM A 366/A 366M - Standard Specification for Steel, Sheet, Carbon, Cold-Rolled, Commercial Quality.

ASTM A 480 - Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip.

ASTM A 627 - Standard Test Methods for Tool-Resisting Steel Bars, Flats, and Shapes for Detention and Correctional Facilities.

ASTM A 653/A 653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.

ASTM A 924/A 924M - Standard Specification for General Requirements for Sheet Steel, Metallic-Coated by the Hot-Dip Process.

ASTM AWS D1.1 - Welding Code.

SUBMITTALS

Submit under provisions of Section 01 30 00 - Administrative Requirements.

Product Data: Manufacturer's data sheets on each product to be used, including:

Preparation instructions and recommendations.

Storage and handling requirements and recommendations.

Installation methods.

Shop Drawings: Shop drawings for each product specified, showing fabrication details, composite structure, and materials to be used as well as outlining installation procedures with no exposed fastenings, caulking, etc.

** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.

Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

Manufacturer's Certificates: Certify products meet or exceed specified requirements.

Maintenance Instructions: Complete maintenance instructions for preventative maintenance and repairs of the units shall be submitted for incorporation in Project Data Book.

Closeout Submittals: Provide manufacturer's maintenance instructions that include recommendations for periodic checking and adjustment of cable tension and periodic cleaning and maintenance of all railing and infill components.

QUALITY ASSURANCE

Manufacturer Qualifications: A manufacturer engaged in the manufacture of the product for a minimum of 10 years.

Installer Qualifications: An installer engaged in the installation of the product for a minimum of 5 years or as recommended by the manufacturer.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

Finish areas designated by Architect.

Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.

Refinish mock-up area as required to produce acceptable work.

Preinstallation Meetings: Conduct meetings to verify project requirements, substrate conditions, manufacturer's installation instructions, and warranty requirements. Comply with Division 1 requirements.

DELIVERY, STORAGE, AND HANDLING

Delivery and Storage:

Deliver and store in manufacturer's original, unopened, undamaged containers, identification labels intact.

Handle and store products according to manufacturer's recommendations. Store off the ground and leave products wrapped or otherwise protected and under clean and dry storage conditions until required for installation.

SEQUENCING

Ensure that locating templates and other information required for installation of products of this section are furnished to affected trades in time to prevent interruption of construction progress.

Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

PROJECT CONDITIONS

Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

WARRANTY

?? Extended beyond 1 year??

PRODUCTS

MANUFACTURERS

Acceptable Manufacturer: PSI LLC, which is located at: 2323 N. 2nd St.; Minneapolis, MN 55411; Tel: 612-789-0925; Fax: 612-789-0196; Email: request info (sales@); Web:

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

Substitutions: Not permitted.

Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

MATERIALS - GENERAL

** NOTE TO SPECIFIER ** Edit the following General paragraphs as required and applicable to project requirements.

Carbon Steel:

Tool resistant Steel: ASTM A 627.

Cold rolled steel sheet: ASTM A 366.

Plates: ASTM A 283/A 283M.

Stainless Steel:

Sheet ASTM A 480 Type 304 with #4 finish.

Plate ASTM A 167 Type 304 with #4 finish.

Fasteners: Minimum 3/4 inch (unless otherwise indicated) conforming to ASTM A 307, A 325.

Weld Nuts: Minimum 3/4 inch (unless otherwise indicated) conforming to ASTM A 307, A 325.

Primer Materials: Prime paint all steel surfaces except for product to receive powder coating and those fabricated of stainless steel.

Powder Coating: Polyester or epoxy powder coating to a 2 mil DFT oven cured at 400 degrees F (205 degrees C).

Color Paint Material: Manufacturer's standard finish and color.

Galvanized Steel: Where specified, galvanize products after fabrication to ASTM A 123. Furnish a minimum galvanized coating of 1.25 oz/sq ft (380 g/sq m).

Welding Materials: AWS D1.1; type required for materials being welded.

TABLES AND SEATING

CB-200 Contoured Bench:

Overall Height: 33-3/4 inches

Seat Height: 17-3/4 inches

Overall Depth 29 inches

** NOTE TO SPECIFIER ** Insert length required. Standard lengths up to 10 feet. Custom lengths are also available with splices required for lengths over 10 feet.

Length: ______

Top and Sides:

10 gauge stainless steel top and sides.

12 gauge stainless steel top and sides.

Construction: Top and sides fully welded on all seams and ground for a seamless surface. Holes are drilled along the top and bottom edges of the bench to allow for fastening to angle iron rails mounted on the wall and floor.

Dampening Material: 1/2 inch thick material along the interior, covering the full length of the bench.

Finish: Chemically degreased with a #4 finish.

Options:

** NOTE TO SPECIFIER ** Select the option if required from the following paragraph and delete if not required.

Detention Handcuff rings or rails

FB-200 Floor Mount Pedestal Bench:

Overall Height: 18 inches

Seat Depth: 12 inches

** NOTE TO SPECIFIER ** Insert length required. Standard lengths are 6 feet and 8 feet. Custom lengths are also available with splices required for lengths over 10 feet.

Length: ______

Top:

** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the one not required.

10 gauge formed steel with 1-1/2 inch deep flanges on all sides.

12 gauge stainless steel with 1-1/2 inch deep flanges on all sides.

Support Pedestals: 2 inch Schedule 40 (2-3/8 inch o.d.) steel pipe, 18 inches high with 10 gauge steel reinforcing top plate, 8 inch by 8 inch by 7 gauge steel base plate with 1/2 inch bolt holes. Provide on 36 inch maximum spacing.

Construction: All joints fully welded and ground smooth.

Finish:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Steel: Chemically degreased and coated with rust inhibitive primer.

Stainless Steel: #4 finish on face, satin finish inside.

Options:

** NOTE TO SPECIFIER ** Select the option if required from the following paragraph and delete if not required.

Handcuff rings or rails.

Full length hand cuff bar.

FMS-200 Floor Mount Stool:

Overall Height: 18 inches

Seat Diameter: 12 inches

Seat top: 14 gauge type 304 stainless steel top, 12 inch diameter by 1-1/2 inches deep with a spun #4 finish.

Reinforcement: full surface 7 gauge steel reinforcement plate, stitch welded to underside of seat and welded to pedestal.

Pedestal: 2 inch Schedule 40 (2-3/8 inch o.d.) steel pipe pedestal, with overall height of 18 inches from floor to top of seat.

Base plate: 8 inches by 8 inches by 7 gauge steel base plate, welded to bottom of pedestal with four 1/2 inch diameter holes for bolting to the floor.

All joints welded and ground smooth.

Finish:

Steel: Chemically degreased and coated with rust inhibitive primer.

Stainless Steel: #4 finish on face, satin finish inside.

Options:

** NOTE TO SPECIFIER ** Select the option if required from the following paragraph and delete if not required.

Handcuff rings.

FMWB-200 Floor Mount Wood Bench:

Size:

** NOTE TO SPECIFIER ** Insert length required. Custom lengths are available with splices required for lengths over 10 feet.

Length: ______

Height/Width: 18 inches high by 19-1/2 inches deep.

Top: Two Laminated hardwood planks each 1-1/4 inches thick by 9-1/2 inches wide with two boards bolted side by side for a total width of 19-1/2 inches.

Frame: 3/8 inch by 2-1/4 inch steel flat bar, cross braced, floor brackets with 1/2 inch holes at floor flanges.

Construction: Planks fastened with 1/4 inch machine threaded carriage screws with lock nuts.

Finish: 2 coats of polyurethane finish on wood top. Rust inhibitive primer finish on steel brackets.

Options:

** NOTE TO SPECIFIER ** Select the option if required from the following paragraph and delete if not required.

7 gauge steel brackets for wall mounting. Embedment plates required.

PB-200 Bench Table:

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom lengths are available with splices required for lengths over 10 feet.

PB-200-4: 4 Person Bench Table 24 inches by 48 inches.

PB-200-6: 6 Person Bench Table 24 inches by 72 inches.

PB-200-8: 8 Person Bench Table 24 inches by 96 inches.

Table top:

** NOTE TO SPECIFIER ** Select table top material required and delete the one not required.

10 gauge steel table top with 2 inch flange each side.

12 gauge stainless steel table top with 2 inch flange each side.

Seats:

** NOTE TO SPECIFIER ** Select seat material required and delete those not required.

10 gauge formed steel channels with 2 inch by 2 inch angle reinforcement under sides, 12 inches by length of table each side.

12 gauge stainless steel 12 inches by length of table each side.

Horizontal braces: 5 inches by 50 inches by 7 gauge steel channels.

Vertical braces: 21-1/2 inches by 30 inches by 7 gauge vertical channel, with 2 inches by 3/8 inch base plate field weld to table top and seat base.

All joints welded and ground smooth.

Finish:

** NOTE TO SPECIFIER ** Select finish required and delete the one not required.

Steel: Chemically degreased and 1 coat universal rust inhibitive primer.

Stainless Steel: #4 finish

Shipped knocked down, field welding required.

SP-200 Pedestal Table

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom lengths are available with splices required for lengths over 10 feet.

SP-200-4-person pedestal table.

SP-200-6 6-person pedestal table .

SP-200-8 8-person pedestal table.

SP-200-HC: With removable seat for ADA handicap access.

Table Top: Underside reinforcement plate, with gussets welded to underside.

** NOTE TO SPECIFIER ** Select table top material required and delete the one not required.

10 gauge steel table top with 2 inch flange each side.

12 gauge stainless steel table top with 2 inch flange each side.

Seats: Seats: 14 gauge stainless steel seat, 12 inch diameter by 1-1/2 inches deep with a 7 gauge steel plate welded to underside.

Base: 3 inches by 3 inches by 1/8 inch steel tube seat base, welded to center post.

Post: 4 inches by 4 inches by 3/16 inch steel center post.

Floor plate: 18 inches by 18 inches by 3/8 inch steel base plate with 5/8 inch holes.

All joints welded and ground smooth.

Finish:

** NOTE TO SPECIFIER ** Select finish required and delete the one not required.

Steel: Chemically degreased and 1 coat universal rust inhibitive primer.

Stainless Steel: #4 finish

Shipped knocked down, field welding required.

WB-200 Wall Mount Bench

Length:

** NOTE TO SPECIFIER ** Select length required. Standard lengths are 6 feet and 8 feet. Custom lengths are also available with splices required for lengths over 120 inches.

6 feet.

8 feet.

Custom:

Top:

** NOTE TO SPECIFIER ** Select table top material required and delete the one not required.

10 gauge formed steel top, 18 inches wide by 1-1/2 inches deep flanges on all sides.

12 gauge stainless steel table top with 2 inch flange each side.

Leg Brackets: 18 inches deep by 12 inches high 7 gauge steel end brackets, welded to bench.

All joints fully welded and ground smooth.

Finish:

** NOTE TO SPECIFIER ** Select finish required and delete the one not required.

Steel: Chemically degreased and 1 coat universal rust inhibitive primer.

Stainless Steel: #4 finish

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraph and delete if not required.

Handcuff rings.

Full length hand cuff bar, as displayed above.

WDK-200 Wall Mount Desk

Top:

** NOTE TO SPECIFIER ** Select table top material required and delete the one not required.

10 gauge formed steel top, 30 inches wide by 16 inches deep with 2 inch flange formed front and back.

12 gauge stainless steel table top 30 inches wide by 16 inches deep with 2 inch flange formed front and back.

Sides: 10 gauge steel sides, formed down from top, 8 inches high, creating a one piece structure with the top, sloping to 2 inches at the front edge.

All corners fully welded and ground smooth.

Finish:

** NOTE TO SPECIFIER ** Select finish required and delete the one not required.

Steel: Chemically degreased and 1 coat universal rust inhibitive primer.

Stainless Steel: #4 finish

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete if not required.

15 inches wide by 18 inches deep with 12 inch by 18 inch seat.

Embed plates available.

WMS-200 Wall Mount Swing Stool

Seat: 12 inches diameter by 1-1/2 inches deep by 14 gauge stainless steel seat, with a 7 gauge steel plate welded to underside.

Swivel Arm: 3/8 inch steel plate bracket, welded to seat reinforcement plate & to swivel pin.

Swivel Pin: 1 inch diameter steel pin.

Swing stop: Prevents seat from swinging into wall.

Mounting Plate: 6 inches by 16 inches by 3/8 inch steel, pre-drilled to bolt directly to a wall or field welded to an embedded plate cast into concrete.

Construction: All seams fully welded and ground smooth for strength and safety.

Finish:

** NOTE TO SPECIFIER ** Select finish required and delete the one not required.

Steel: Chemically degreased and 1 coat universal rust inhibitive primer.

Stainless Steel: #4 finish

Options:

** NOTE TO SPECIFIER ** Select the option required from the following paragraph and delete if not required.

Provide with heavier gauge steel and steel brackets for wall mounting

** NOTE TO SPECIFIER ** Select the Accessories required from the following paragraphs and delete those not required. Note that the material specified are available in custom sizes, contact PSI for additional information.

ACCESSORIES

** NOTE TO SPECIFIER ** PSI Bar Grille features double-ribbed, tool-resistant Security Bar ideal for security doors, partitions, access points, and jail doors.

BAR-600 Bar Grille: Double-ribbed, Tool-Resistant Steel Bar Grille.

Bars:

** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the one not required.

7/8 inch diameter double ribbed jail bar, 5 inches o.c..

7/8 inch diameter double ribbed jail bar, 4 inches o.c..

Cross Bars:

** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the one not required.

3/8 inch by 2-1/4 inches mild steel flat bar 18 inches o.c., with punched holes for ribbed bars 5 inches o.c..

3/8 inch by 2-1/4 inches mild steel flat bar 12 inches o.c., with punched holes for ribbed bars 5 inches o.c..

Assembly: Notch each side of the ribbed bar at cross bars and pass the ribbed bars through the cross bars and rotate 90 degrees to lock the bars together.

Anchorage: Anchor to walls with a 3 inches by 2 inches by 3/16 inches angle bolted to wall, and field weld.

Finish: Chemically degrease and 1 coat of rust inhibitive primer.

** NOTE TO SPECIFIER ** PSI Duct Grille features double-ribbed, tool-resistant Security Bar for security duct access points,

BAR-600 Duct Grille: Double-ribbed, Tool-resistant Bar Grille.

Body: Formed 12 ga. steel body.

Bars:

** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the one not required.

7/8 inch diameter double ribbed jail bar, 5 inches o.c..

7/8 inch diameter double ribbed jail bar, 4 inches o.c..

Cross Bars:

** NOTE TO SPECIFIER ** Select one of the following paragraphs and delete the one not required.

3/8 inch by 2-1/4 inches mild steel flat bar 18 inches o.c., with punched holes for ribbed bars 5 inches o.c..

3/8 inch by 2-1/4 inches mild steel flat bar 12 inches o.c., with punched holes for ribbed bars 5 inches o.c..

Assembly: Notch each side of the ribbed bar at cross bars and pass the ribbed bars through the cross bars and rotate 90 degrees to lock the bars together.

Finish: Chemically degrease and 1 coat of rust inhibitive primer.

GB-600 Safety Grab Bar

Bar: 1-1/2 inch diameter by 18 gauge stainless steel tubing with formed ends to hold bar 1-1/2 inch from wall.

Length:

** NOTE TO SPECIFIER ** Select one of the following length paragraphs and delete the ones not required.

18 inches

24 inches

30 inches

36 inches

42 inches

54 inches

Brackets: 3 inch diameter by 11 gauge stainless steel bracket, welded to bar return at each end.

Fasteners: Holes in mounting flange sized for 1/4 inch screws to mount to wall or embeds.

SS Finish: #4 brushed finish.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Closure plate: 12 gauge stainless steel enclosure plate.

Drain Holes: 1/4 inch diameter drain holes 12 inches o.c.

GB-600-L L-shape Safety Grab Bar

Bar: 1-1/2 inch diameter by 18 gauge stainless steel tubing with formed ends to hold bar 1-1/2 inch from wall.

Length:

** NOTE TO SPECIFIER ** Select one of the following length paragraphs and delete the ones not required.

18 inches by 30 inches

18 inches by 36 inches

24 inches by 30 inches

24 inches by 36 inches

Brackets: 3 inch diameter by 11 gauge stainless steel bracket, welded to bar return at each end.

Fasteners: Holes in mounting flange sized for 1/4 inch screws to mount to wall or embeds.

SS Finish: #4 brushed finish.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Closure plate: 12 gauge stainless steel enclosure plate.

Drain Holes: 1/4 inch diameter drain holes 12 inches o.c.

HCGB-600 Hand Cuff Bar

Bar: 1-1/2 inch diameter by 18 gauge stainless steel tubing with formed ends to hold bar 1-1/2 inch from wall.

Length:

** NOTE TO SPECIFIER ** Select one of the following length paragraphs and delete the ones not required.

18 inches by 30 inches

18 inches by 36 inches

24 inches by 30 inches

24 inches by 36 inches

Brackets: 3 inch diameter by 11 gauge stainless steel bracket, welded to faceplate with 1/4-20 SS weld nuts.

Fasteners: 1/4-20 stainless steel architectural sex bolts, 1/4-20 thru bolts and 1/4-20 nylon nuts.

SS Finish: #4 brushed finish.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Hand Cuff Rings.

** NOTE TO SPECIFIER ** Safety hooks are designed to allow the hooks to hold clothing, but collapse under heavier weight.

SH-600 Single Safety Hook:

Size: 4-5/16 inches high by 1 inch wide and extending 3 inches.

Body: 11 gauge formed stainless steel bracket with 2 mounting holes.

Hook: 8 gauge stamped stainless steel hook.

Assembly: Sandwich hook between 2 neoprene washers and secure with 1/4 inch-20 button head tamper resistant screw. Tighten screw to proper tension.

Finish: Stainless Steel.

SH-601 Safety Hook Strip

Backplate: 7 gauge steel, 16 inches long 5-1/2 inches high.

Hooks:

4-5/16 inches high by 1 inch wide and extending 3 inches.

Body: 11 gauge formed steel bracket with 2 mounting holes.

Hook: 8 gauge stamped steel hook.

Assembly: Sandwich hook between 2 neoprene washers and secure with 1/4 inch-20 button head tamper resistant screw. Tighten screw to proper tension.

Fasteners: Tamper-resistant security screws fasten the hook strip to the wall or plate.

Finish: chemically degreased and finished with a coat of rust-inhibitive primer; the hooks have zinc plating.

SHB-600 Ball and Socket Single Safety Hook

Body: 14 gauge formed stainless steel body, 4 inches wide by 4 inches high by 1 inch deep.

Hooks: Stainless steel ball in socket hooks, fastened from behind with an adjustable tensioner plate.

Finish: Polish stainless steel to a uniform #4 finish.

Fasteners: Fasten to wall or embed plate with 6- 1/4-20 tamper resistant security screws.

SHB-601 Ball & Socket Safety Hook Strip

Body: 14 gauge formed stainless steel body, 18 inches wide by 6-1/2 inches high by 1 inch deep.

Hooks: Stainless steel ball in socket hooks, fastened from behind with an adjustable tensioner plate.

Finish: Polish stainless steel to a uniform #4 finish.

Fasteners: Fasten to wall or embed plate with 6- 1/4-20 tamper resistant security screws.

TPH-600 Recessed Stainless Steel Toilet Paper Holder

Material: Type 304, 14 ga stamped stainless steel.

Size: 5-3/8 inch i.d. by 4-1/4 inches deep, with 3/4 inch flange and perimeter.

Anchorage: Two 1/4-20 weld nuts welded to back side of can fastened with two 1/4-20 threaded rod, sized to extend 1 inch from back side of wall.

Back bar: 7 gauge by 1-1/2 inches by 8 inches steel bar.

Finish: #4 finish on face, satin finish inside.

** NOTE TO SPECIFIER ** Select the option if required from the following paragraph and delete if not required.

Option: Cast into concrete anchorage.

** NOTE TO SPECIFIER ** Woven rod doors and partitions are the kinds of jail doors PSI creates for individual law enforcement sites.

WOV-600 Woven Rod Doors & Partitions

Frame:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Tubular shaped frame fabricated of a 12 gauge steel channel, 1-3/4 inches wide by 3 inches high, notched every 2-1/4 inches to receive woven rod. Cap channel with a 2-3/4 inch by 12 gauge steel plate, and stitch weld 9 inches o.c.

Tubular shaped frame fabricated of a 10 gauge steel channel, 1-3/4 inches wide by 3 inches high, notched every 2-1/4 inches to receive woven rod. Cap channel with a 2-3/4 inch by 12 gauge steel plate, and stitch weld 9 inches o.c.

Tubular shaped frame fabricated of a 12 gauge stainless steel channel, 1-3/4 inches wide by 3 inches high, notched every 2-1/4 inches to receive woven rod. Cap channel with a 2-3/4 inch by 12 gauge stainless steel plate, and stitch weld 9 inches o.c.

Mesh:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

1/4 inch diameter, mild steel rod, woven 2-1/4 inches o.c. each way, double crimped, and welded at ever other rod where it intersects the channel frame.

3/8 inch diameter, mild steel rod, woven 2-1/4 inches o.c. each way, double crimped, and welded at ever other rod where it intersects the channel frame.

1/4 inch diameter, stainless steel rod, woven 2-1/4 inches o.c. each way, double crimped, and welded at ever other rod where it intersects the channel frame.

Mounting: Mount frame into a 10 gauge formed steel channel, expansion anchored to the wall, and field welded to the mount channel.

Finish:

** NOTE TO SPECIFIER ** Select the finish required from the following paragraphs and delete the one not required.

Steel: Chemically degreased and coated with rust inhibitive primer.

Stainless Steel: #4 finish on face, satin finish inside.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

10 gauge steel frame.

3/8 inch diameter woven wire 2-1/4 inches o.c. each way.

Stainless steel frame and wire

CABINETS AND LOCKERS

GC-400 Pistol & Rifle Security Locker

Mount:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

In-Wall.

On-Wall.

Custom.

Body: Formed 10 gauge steel body, 54-1/2 inches wide by 58-1/2 inches high by 12 inches deep.

Doors: 15-3/8 inches wide by 8-1/8 inches high by 10 gauge steel pistol door and 7-7/8 inches wide 55-3/8 inches high by 10 gauge steel rifle door lined with 1/8 inch thick felt on bottom.

Hinge: 16 gauge steel continuous piano hinge.

Locks: Individually keyed and master keyed pin tumbler snap lock with 2 keys per compartment.

Mounting Frame: 2 inch by 2 inch by 3/16 inch steel angle frame, welded to body exterior

All joints welded and ground smooth.

Finish: Chemically degreased with 1 coat universal rust inhibitive primer.

KC-400 Detention Key Cabinet

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom capacity, sizes, arrangements, and inserts available by request.

KC-400-060; Key capacity, 60.

KC-400-180; Key capacity, 180.

KC-400-300; Key capacity, 300.

Door: 10 gauge formed steel, 1-1/4 inches deep.

Lock: Prepped for a high security mechanism.

Hinge: 16 gauge steel continuous piano hinge.

Panels: 10 gauge steel plate with key racks.

** NOTE TO SPECIFIER ** Select rack required and delete those not required.

Paracentric key rack holding 4 keys per hook, 16 keys per strip

Mogul key rack containing 3 keys per hook, with 24 keys per strip

Construction: All joints welded and ground smooth.

Finish: Chemically degreased and coated with a universal rust inhibitive primer.

PC-400 Multi-compartment Locking Cabinet

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom capacity, sizes, arrangements, and inserts available by request. Custom sized lockers can be assembled into any number of compartments.

PC-400-3; Security locker with 3 compartments.

PC-400-6; Security locker with 6 compartments.

PC-400-9; Security locker with 9 compartments.

PC-400-X; Custom

Body: Formed 10 gauge steel body, 20 inches wide x 24-1/8 inches high by 10 inches deep.

Mounting Frame: 2 inches by 2 inches by 3/16 inch steel angle frame, welded to body.

** NOTE TO SPECIFIER ** Select mount required and delete those not required. Surface, recessed, or custom mounting depths up to 10 inches.

Surface mount

Semi-Recessed mount

Recessed mount.

Hinge: 16 gauge steel continuous piano hinge.

Door: 9-9/16 inches wide by 7-1/2 inches high by 10 gauge steel.

Lock: Individually keyed and master keyed pin tumbler snap mechanism with 2 keys per compartment.

Compartment: 10 inches deep by 9 9/16 inches wide by 7-1/2 inches high and shelf covered with 1/8 inch thick felt.

Construction: All joints welded and ground smooth.

Finish: Chemically degreased and coated with a universal rust inhibitive primer.

PD-400 Pass Drawer

Frame:

** NOTE TO SPECIFIER ** Select steel or stainless steel as required and delete the one not required.

12 gauge formed steel body.

12 gauge formed stainless steel body.

Door:

** NOTE TO SPECIFIER ** Select steel or stainless steel as required and delete the one not required.

12 gauge steel Interior door, 17-5/8 inches wide by 9 inches deep.

12 gauge stainless steel Interior door, 17-5/8 inches wide by 9 inches deep.

Drawer:

** NOTE TO SPECIFIER ** Select steel or stainless steel as required and delete the one not required.

12 gauge formed steel with stainless steel exterior.

12 gauge formed stainless steel with stainless steel exterior.

Hardware: Zinc plated ball bearing drawer slides. Steel continuous 16 gauge piano hinge.

Construction: All joints welded and ground smooth.

Finish:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Steel: Chemically degreased and coated with rust inhibitive primer.

Stainless Steel: #4 finish on face, satin finish inside.

PL-408 Locking Cabinet With Multiple Tip-out Compartments

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom capacity, sizes, arrangements, and inserts available by request. Custom sized lockers can be assembled into any number of compartments.

PL-408-3; A 3 compartment locker.

PL-408-6; A 6 compartment locker.

PL-408-9; A 9 compartment locker.

PL-408-X; Custom

Body: Formed 10 gauge steel body, 35 inches wide by 29-1/2 inches high by 6 inches deep.

Mounting Frame: 2 inches by 2 inches by 3/16 inch steel angle frame, welded to body.

** NOTE TO SPECIFIER ** Select mount required and delete those not required. Surface, recessed, or custom mounting depths up to 6 inches.

Surface mount

Semi-Recessed mount

Recessed mount.

Hinge: 16 gauge steel continuous piano hinge.

Drawers: 15-1/4 inches wide x 8-7/16 inches high 10 gauge steel, lined with 1/8 inch think felt.

Locks: Individually and master keyed pin tumbler snap lock with 2 keys per compartment.

Construction: All joints welded and ground smooth.

Finish: Chemically degreased and coated with a universal rust inhibitive primer.

DOORS AND ACCESS POINTS

CAD-100 Chase Access Door

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom capacity, sizes, arrangements, and inserts available by request.

12 inches by 12 inches

16 inches by 16 inches

24 inches by 24 inches

30 inches by 30 inches

24 inches by 36 inches

Custom

Door: 10 gauge flat steel plate.

Frame: 2 inches by 2 inches by 3/16 inch steel angle, 4 sides, cut and notched at each corner to create a smooth square corner.

Door stop: 1 inches by 1 inches by 1/8 inch steel angle, recessed so door face fits flush with the angle frame.

Hinges: #3 high security detention hinges 3 inches by 4 inches with non-removable pins.

Lock: Prepped for high security detention deadbolt lock, concealed bolt receiver.

Finish: Chemically degreased, with one coating of rust inhibitive primer.

Mounting option: 2 inches by 6 inches by 10 gauge steel masonry anchors.

Finish: Chemically degreased and coated with rust inhibitive primer.

CAD-101 Chase Access Door

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom capacity, sizes, arrangements, and inserts available by request.

24 inches by 24 inches

24 inches by 36 inches

24 inches by 48 inches

16 inches by 36 inches

24 inches by 60 inches

Custom

Door: 7 gauge formed steel plate, with 1-1/4 inch flange, 4 sides.

Frame: 3 inches by 2 inches by 3/16 inch steel angle, manufactured with a smooth square corner.

Doorstop: 1 inch by 1 inch by 1/8 inch steel angle, recessed so door face fits flush with the angle frame.

Hinges:

** NOTE TO SPECIFIER ** Select hingle required and delete the one not required.

#3 high security detention hinges, 3 inches by 4 inches, with non-removable pins.

Continuous piano hinge.

Lock: Prepped for high security detention deadbolt lock, concealed bolt receiver.

Finish: Chemically degreased, with a coating of rust inhibitive primer.

Mounting option: 2 inches by 6 inches by 10 gauge steel masonry anchors.

** NOTE TO SPECIFIER ** FP-103 Retrofit Food Pass mounts into a hole cut into an cell existing door.

FP-103 Food Pass Door Retrofit

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom available by request.

5 inches by 15-1/2 inch opening.

Custom.

Door: 7 gauge flat door and reinforcement detention security plate.

Frame: 7 gauge steel face frame with 2 inch by 2 inch by 10 gauge steel angle frame to enclose the backside of the opening. Accommodates 1-3/4 inch and 2 inch thick doors.

Hinges:

** NOTE TO SPECIFIER ** Select hinge required and delete the one not required. Custom available by request.

#3 detention security hinges, 3 inches by 4 inches, with non-removable pins that open to 90 degrees.

Continuous piano hinge.

Lock: Prepped for high security detention deadbolt lock, concealed bolt receiver.

Finish: Chemically degreased, with a coating of rust inhibitive primer.

** NOTE TO SPECIFIER ** Select options required from the following paragraphs and delete those not required.

Mounting: 3/8 inch diameter holes for 1/4-20 screws.

Latch: Finger Pull

FP-120 Food Pass Door

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom available by request.

5 inches by 15-1/2 inch opening.

Custom.

Door: 7 gauge flat door and reinforcement detention security plate.

Frame: 2 inch by 7 gauge steel frame.

Hinges:

** NOTE TO SPECIFIER ** Select hinge required and delete the one not required. Custom available by request.

#3 detention security hinges, 3 inches by 4 inches, with non-removable pins that open to 90 degrees.

Continuous piano hinge.

Lock: Prepped for high security detention deadbolt lock, concealed bolt receiver.

Finish: Chemically degreased, with a coating of rust inhibitive primer.

** NOTE TO SPECIFIER ** Select options required from the following paragraphs and delete those not required.

Mounting: 3/8 inch diameter holes for 1/4-20 screws.

Latch: Finger Pull

PH-100 Pass Hopper

Size:

** NOTE TO SPECIFIER ** Select size required and delete those not required. Custom available by request.

12 inches deep by 16 inches high.

9 inches deep by 11 inches high.

9 inches deep by 11 inches high by 40 inches inches long.

Custom

Frame: Formed steel construction, assembled to fit a standard 16 inch block width.

** NOTE TO SPECIFIER ** Select material required and delete the one not required.

10 gauge stainless steel.

10 gauge steel.

Hopper: Rolled stainless steel hopper with pull handle and 1/2 inch diameter pivot pins on Oilite bushings.

** NOTE TO SPECIFIER ** Select material required and delete the one not required.

Stainless steel.

Steel.

Latch: Slide bolt latch only on secured side of hopper.

Finish:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Stainless Steel: #4 finish.

Steel: Chemically degreased and coated with rust inhibitive primer.

PS-100 Package Pass Thru

Size:

** NOTE TO SPECIFIER ** Select size required and delete the one not required.

15-1/4 inch by 14-3/4 inch opening.

Custom

Door: 10 gauge. formed stainless steel.

Body: 10 gauge steel top, bottom, and sides.

Frame: 2 inch by 7 gauge steel frame. Field welded after installation.

Hinge: 14 gauge piano hinge, concealed under door.

Latch: Paddle latch on secured side, internal latch controls on unsecured side.

Construction: All joints Fully welded and ground smooth.

Finish:

Stainless Steel: #4 finish.

Steel: Chemically degreased and coated with rust inhibitive primer.

BUNKS

FSB-300 Free Standing Single Bunk

Size: Bunk has a pan of 10-gauge steel, measuring 27 inches by 79-3/8 inches. Front and rear flanges are formed up 2 inches, with a 1 inch hem.

Legs: 2 inches by 2 inches by 1/8 inch steel angle iron, by 18 inches in height.

Anchor Plates: 2 inches by 2 inches by 10 gauge steel plate with 1/2 inch diameter holes for bolting to floor.

All joints welded and ground smooth.

Finish: Chemically degreased and 1 coat universal rust inhibitive primer.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Open front shelf.

Under bunk drawer.

Perforated with 1 inch diameter holes for ventilation.

FSB-300-D Free Standing Double Bunk

Size: Bunk has a pans of 10 gauge steel, measuring 27 inches by 79-3/8 inches. Front and rear flanges are formed up 2 inches, with a 1 inch hem.

Legs: 2 inches by 2 inches by 3/16 inches steel angle iron, by 53 inches height.

Anchor Plates: 2 inches by 2 inches by 10 gauge steel plate with 1/2 inches diameter hole for bolting to floor, anchors not by PSI.

Assembly: Units are shipped knocked down, field welding required.

All joints welded and ground smooth.

Finish: Chemically degreased and 1 coat universal rust inhibitive primer.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Open front shelf.

Under bunk drawer.

Perforated with 1 inch diameter holes for ventilation.

Ladder.

UBD-300 Under Bunk Drawers

Size:

** NOTE TO SPECIFIER ** Select size required and delete the one not required.

Overall: 24 inches D by 23 inches W by 10 inches H

Custom

Body: Formed 14 gauge steel body, front and flanges for slides.

Slides: 10 gauge steel slides, welded to underside of bunk pan, 2 per drawer.

Hasp: 1 inch by 2 inch by 10 gauge steel with lock hole welded to face of bunk pan so hasp slides through slot in front plate of drawer.

Pull: 1/2 inch lip at underside of drawer forms a drawer pull.

Fully welded construction.

Stop: 2 inches by 2 inches by 3/16 inches steel angle bolted to underside of pan so drawer is not removable.

Finish: Chemically degreased and 1 coat rust inhibitive primer.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Combination lock.

Bolt on application.

Wall-Mount Single Bunk

Size:

** NOTE TO SPECIFIER ** Select size required and delete the one not required.

Bunk has pan of 10 gauge steel, front and rear flanges formed up 2 inches, with 1 inch hem., 27 inches by 79-5/8 inches pan size.

Custom

End Brackets: 7 gauge steel end brackets, welded to pan. 29 inches deep by 12 inches high with 2 inches wall flange. Bracket holds bunk pan 2 inches off wall.

Embed plates: Field weld brackets to 7 gauge by 4 inches by 14 inches steel plates, cast into wall with 10 gauge by 2 inches by 4 1/2 inches anchors. 2 embeds per bunk.

All joints welded and ground smooth.

Finish: Chemically degreased and 1 coat universal rust inhibitive primer.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Open front shelf.

Under bunk drawer.

Perforated with 1 inch diameter holes for ventilation.

DESKS

IDK-200 Floor Mounted Desk

Top: 30 inches wide by 15 inches deep with a 1-1/2 inches flange formed up in back, and down in front and sides.

** NOTE TO SPECIFIER ** Select the top material required from the following paragraphs and delete the one not required.

10 gauge formed steel.

10 gauge formed stainless steel.

Sides: 10 gauge formed steel sides, 15 inches deep by 30 inches high, with 1 1/2 inches flange formed front and back. Each leg has a 1-3/4 inches by 1-3/4 inches by 10 gauge steel mount plate with a 1/2 inches diameter hole for bolting to floor, 1 inch diameter pipe foot rest.

Shelf: Two 10 gauge steel shelves, 10 inches deep, by 10 inches high by 10 inches wide.

Seat: 12 inches diameter by 1-1/2 inches deep, 14 gauge stainless steel with a 7 gauge plate welded to underside.

Swing Bracket: Swivel pin 1 inch diameter steel, rotating inside two 1-1/2 inch diameter cylinders at each end.

Swing Arm: 3/8 inches thick steel plate, welded to pivot pin, and seat reinforcing plate.

Finish:

Stainless Steel: #4 finish.

Steel: Chemically degreased and coated with rust inhibitive primer.

Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete the ones not required.

Towel Bar: 3/8 inches by 2-1/4 inches by 12 inches long steel towel bar.

SHELVING

RS-515 Recessed Stainless Steel Shelf

Body: 14 gauge type 304 stainless steel.

Size:

Interior dimensions: 16 inches wide by 5 inches high by 4 inches deep.

Custom.

Anchorage:

** NOTE TO SPECIFIER ** Select the anchorage required from the following paragraph and delete the one not required.

Wall anchorage, 1/4-20 weld nuts welded to back side of can, fastened with 4-1/4 inch 20 threaded rod, sized to extend 1 inch from back side of wall.

Cast-In-Place anchorage.

Back bar: 7 gauge by 1-1/2 inch- by 8 inch- steel bar.

Finish: #4 finish on face, satin finish inside.

Options:

** NOTE TO SPECIFIER ** Select the option required from the following paragraph and delete if not required.

Front Mounting.

Wall Mount Cantilevered TV Shelf:

Size:

** NOTE TO SPECIFIER ** Select size required and delete the one not required. Custom sizes and Flat Screen sizing are also available options as well as, a swivel-type mount.

24 inches wide by 16 inches deep, with 1 inch high flanges on all four sides for up to 27 inches TV set.

36 inches wide by 30 inches deep, with 1 inch high flanges on all four sides for up to 35 inches sets.

Custom

Body: 12 gauge Mild steel pan, 24 inches wide by 16 inches deep by 1 inch high flanges on 4 sides

Cantilever Arm: 2 inches by 3 inches by 1/8 inch steel tubing, welded to wall plate and underside of pan

Length: 16-3/4 inches to hold back of pan 2 inches off wall

Mount plate: 6 inches by 14 inches by 1/4 inch back plate, with 3/8 inch diameter holes for bolting to wall, or field weld to embed.

Fully welded construction.

Finish: Chemically degreased and 1 coat rust inhibitive primer.

Options:

** NOTE TO SPECIFIER ** Select the option required from the following paragraph and delete if not required.

Swivel type mount.

WSS-500 Steel Safety Shelf

Size:

** NOTE TO SPECIFIER ** Select size required and delete the one not required.

18 inches wide by 8 inches deep 10 gauge steel shelf with sloped sides and a 1 inch hemmed front edge.

Custom

Back plate: 12 inches by 18 inches by 10 gauge steel plate with 7-3/8 inches diameter mounting holes.

Hooks: Four friction type collapsible safety hooks, fillet welded to back plate.

Finish: Chemically degreased and coated with 1 coat rust inhibitive primer.

WSSB-500 PSI Steel Safety Shelf:

Size:

** NOTE TO SPECIFIER ** Select size required and delete the one not required.

18 inches wide by 8 inches deep 14 gauge stainless steel shelf with sloped sides and a 1 inch hemmed front edge.

Custom

Back plate: 18 inches by 12 inches by 1 inch by 14 gauge stainless steel plate.

Hooks: 4- stainless steel, ball/peg type safety hooks.

Anchorage: 1/4-20 BH high security detention screws.

Finish: #4 finish on exposed stainless steel.

EXECUTION

EXAMINATION

Do not begin installation until substrates have been properly prepared.

If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

PREPARATION

Clean surfaces thoroughly prior to installation.

Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

INSTALLATION

Install in accordance with manufacturer's instructions.

Protect elements surrounding work of this section from damage or disfiguration.

Secure anchorages and connections to adjacent construction.

Finish exposed field welds to present a smooth uniform surface.

ADJUSTING AND CLEANING

Touch-up exposed surfaces scratched or marred during shipment, installation, or handling.

Remove temporary coverings and protection of adjacent work areas. Repair or replace damaged installed products. Clean installed products in accordance with manufacturer's instructions before owner's acceptance.

Remove from project site and legally dispose of construction debris associated with this work.

PROTECTION

Protect installed products until completion of project.

Touch-up, repair or replace damaged products before Substantial Completion.

SCHEDULES

** NOTE TO SPECIFIER ** Retain Paragraph below if required to suit project requirements. Identify products by name on the Drawings or use this paragraph to define the location of each type of material to be used. The following are some examples of schedule references. Edit as required to suit project or delete and identify products on the Drawings.

:

:

END OF SECTION ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download