A0bf27d878ca693c13cc …



?SECTION 09 96 00High-Performance Coatings – Architectural Powder Coatings for LEED? v4 ProjectsDisplay hidden notes for specifier (under File > Options > Display in MS Word 2016) PART 1 – GENERALSUMMARY This section includes factory applied LEED? v4 compliant powder coatings for architectural metal applications.** NOTE TO SPECIFIER ** Delete any sections below not relevant for project; add others as required.Related sections include, but shall not be limited to, the following:Section 05 73 13 - Glazed Decorative Metal Railings.Section 05 73 16 - Wire Rope Decorative Metal Railings.Section 05 73 00 - Decorative Metal Railings.Section 07 41 13 - Metal Roof Panels.Section 07 42 13 - Metal Wall Panels.Section 07 61 00 - Sheet Metal Roofing.Section 07 62 00 - Sheet Metal Flashing and Trim.Section 07 71 13 - Manufactured Copings.Section 08 30 00 - Specialty Doors and Frames.Section 08 41 13 - Aluminum-Framed Entrances and Storefronts.Section 08 43 26 - All-Glass Storefronts.Section 08 42 29 - Automatic Entrances.Section 08 42 33 - Revolving Door Entrances.Section 08 51 13 - Aluminum Windows.Section 08 63 13 - Domed Metal-Framed Skylights.Section 08 44 13 - Glazed Aluminum Curtain Walls.Section 08 90 00 - Louvers and Vents.Section 10 51 00 - Lockers.Section 13 34 19 - Metal Building Systems. 1.2 REFERENCES** NOTE TO SPECIFIER ** Delete references from below list if not required by text of the edited sectionAmerican Architectural Manufacturers Association (AAMA):AAMA 2603 - Voluntary Specification, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and PanelsAAMA 2604 - Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum ExtrusionsAAMA 2605 - Voluntary Specification, Performance Requirements and Test Procedures for Superior Performing Organic Coatings on Aluminum ExtrusionsAAMA 643 - Voluntary Specification, Performance Requirements and Test Procedures for Solar Reflectance FinishesASTM International (ASTM):ASTM c1549-09 Analysis of color sample for Solar Reflectance;ASTM c1371-15 Analysis of color sample for Thermal Emittance;ASTM E 1980 - Practice for Calculating Solar Reflectance Index of Horizontal and Low-Sloped Opaque SurfacesQualicoat: 15th Edition of Specifications for a Quality label for liquid and powder organic coatings on Aluminium for Architectural specifications:Qualicoat Class 1Qualicoat Class 2Qualicoat Class 3 European Standards (EN):EN 15804:2013 Sustainability of construction works - Environmental product declarations - Core rules for the product category of construction productsInternational Standards Organization (ISO):ISO 2813:2014 Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degreesISO 9001:2015 Quality Management Systems – RequirementsISO 14025:2006 Environmental labels and declarations - Type III environmental declarations -- Principles and proceduresISO 17065:2012 Conformity assessment – Requirements for bodies certifying products, processes and servicesISO 21930:2017 Sustainability in buildings and civil engineering works -- Core rules for environmental product declarations of construction products and servicesUnited States Green Building Council (USGBC):LEED? v4 BD+C Building Design & Construction for New Construction, Core & Shell, Schools, Retail, Data Centers, Warehouses & Distribution Centers, Hospitality and HealthcareSustainable Sites (SS) Credit: Heat Island ReductionMaterials & Resources (MR) Credits:Building Product Disclosure & Optimization – Environmental Product DeclarationBuilding Product Disclosure & Optimization - Material Ingredients1.3 SUBMITTALSSubmit under provisions of Section 01 33 00, Submittal Procedures.Product data: Manufacturer’s current Technical Data Sheets (TDS) and Application Guide (AG) on each product to be used, including, but not limited to the following:Product description and typical usage areasProduct performance and aesthetic data, including gloss value measured per ISO 2813Surface preparation requirements and recommendationsApplication methods and cleaning instructionsStorage and handling requirements and recommendationsGreen building standards contribution statementsSelection samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.Samples for verification: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, color, and patterns. Resubmit until required gloss, color and texture of finish coat are achieved.Cleaning and maintenance instructions for inclusion in project’s operation and maintenance manual.LEED? v4 submittals: For projects pursuing the Building Product Disclosure and Optimization (BPDO) credits within the Materials & Resources (MR) category, USGBC requires submission of the BPDO calculator supported with the following documentation and information:** NOTE TO SPECIFIER ** LEED? v4 requires projects to use at least 20 different permanently installed products sourced from at least 5 different manufacturers. Only a product-specific type III EPD is valued as one whole product. Paints of different gloss levels (not colours) are considered as separate products because each paint type is specified to serve a different function. If manufacturers are separate legal entities, then each one is considered as a different manufacturer.Product-specific Type III Environmental Product Declaration (EPD) conforming to ISO 14025, ISO 21930 and EN 15804 with cradle to gate scope, including third-party verification by an established EPD program operator explicitly recognizing the manufacturer as a participant.Self-declaration by manufacturer on each product’s technical data sheet documenting material ingredient optimization via the International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 ppm and not containing substances on the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH) Authorization list – Annex XIV, the Restriction list – Annex XVII and the SVHC (Substances of Very High Concern) candidate rmation to include in the BPDO calculator such as manufacturer name, material description matching manufacturer naming convention of the product and material costFor projects pursuing SS Credit: Heat Island Reduction - provide product test reports to document compliance with solar reflectance index (SRI) requirements. Product test reportsQualifications: For factory applied coatings applicatorGuarantee: Draft Guarantee agreement; Process Control and Guarantee Information document** NOTE TO SPECIFIER ** Only projects registered for LEED? v3 before the closing date of October 31, 2016 may submit their application until the certification sunset deadline of June 30, 2021.QUALITY ASSURANCEQuality system: Provide the products of a manufacturer who holds valid ISO 9001 certification. Provide architectural powder coatings approved by Qualicoat and/or compliant to AAMA requirements that provide assurance of high quality and durability for Architectural powder coatings. Applicator qualifications: Specified powder coating needs to be applied by a powder coatings manufacturer’s certified applicator that is equipped, trained and approved for application of coatings required for this project, and is approved to provide guarantee specified in this section.** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant it. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.Mockups: Provide a mock-up for evaluation of surface preparation techniques and application quality.Finish areas designated by architect.Do not proceed with remaining work until the mock-up is approved by the architect.Refinish mock-up area as required to produce acceptable work.DELIVERY, STORAGE AND HANDLINGDeliver, unload and store factory-coated items so that they remain free of damage or deformation. Package and protect items during shipping and handling. Protect stored items from water; stack to facilitate drainage. Keep shop-coated items out of contact with materials that may adversely affect the coatingProtect shop-coated items with protective covering until installedHandling: Handle materials with care to avoid damagePROJECT CONDITIONSMaintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by Manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limitsSEQUENCING AND SCHEDULING Ensure that products of this section are supplied according to the agreed project schedule to prevent interruption of construction progress.WARRANTYCoating Warranty: Coating applicator's warranty in which applicator agrees to repair finish or replace coated items that demonstrate deterioration of shop-applied finishes within warranty period indicated.** NOTE TO SPECIFIER ** Jotun Super Durable guarantee provisions. Delete if not required.Qualicoat Class 2/ AAMA 2604 Powder Coatings on Aluminum Extrusions:Guarantee is valid only if the coating is applied by a Jotun’s approved applicatorScope, terms and conditions of a Guarantee are defined in a Draft Guarantee agreement document for a specific product and in Process Control and Guarantee Information document by Jotun which should be submitted as mentioned in Section 1.3 of this documentGuarantee Period: 25 years on the building performance with Chalking resistance, Color retention and Cracking resistance levels defined in the Guarantee document** NOTE TO SPECIFIER ** Jotun Durasol guarantee provisions. Delete if not required.Qualicoat Class 3/ AAMA 2605 Powder Coatings on Aluminum Extrusions:Guarantee is valid only if the coating is applied by a Jotun’s approved applicatorScope, terms and conditions of a Guarantee are defined in a Draft Guarantee agreement document for a specific product and in Process Control and Guarantee Information document by Jotun which should be submitted as mentioned in Section 1.3 of this documentGuarantee Period: 30 years on the building performance with Chalking resistance, Color retention and Cracking resistance levels defined in the Guarantee documentPART 2 – PRODUCTS2.1 MANUFACTURERSAcceptable Manufacturer: Jotun A/S including any of its worldwide manufacturing facilities. See full listing here: ** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.Substitutions: Not permitted.Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements. When submitting request for substitution, provide complete product data specified above under Submittals, for each substitute product.MATERIALSGeneral:Powder coatings for architectural exterior applications primarily for windows, doors and facades on aluminum substrates.System:Pre-treatment: Aluminum components shall receive a full multi-stage chromate conversion coating or suitable chrome-free pretreatment to clean and prepare the substrate for the coating process.Application: Apply powder coating in accordance with coating manufacturer's requirements specified in Technical data sheet (TDS) and Application guidelines (AGs) for each product and Qualicoat/AAMA requirements for indicated finish.Dry Film Thickness (DFT): 50-90 μm depending on specified product defined in Product TDS. Low-Emitting Materials: For interior coatings: Comply with testing and product requirements of California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers." Environmental Product Declaration: Type III Environmental Declarations.Jotun Super Durable 2901: Approval Date - 18/06/2018 (Validity 5 years), Registration Numbers: NEPD -1566-599 (Jotun Boya); NEPD-1567-599 (Jotun Thailand); NEPD-1564-599 (Jotun CZECH) and NEPD-1563-599 (Jotun UAE). Jotun Super Durable 2903: Approval Date - 05/03/2018 (Validity 5 years), Registration Numbers: NEPD-1522-521 (Jotun UAE); Approval date 18-07-2017 (Validity 5 years) NEPD -1366-451 (Jotun Boya); Approval date 05-03-2018 (Validity 5 years) NEPD-1520-521 (Jotun Thailand) and NEPD-1521-521 (Jotun China); Approval date 18-06-2018 (Validity 5 years) NEPD-1565-599 (Jotun CZECH). Jotun Super Durable 2905: Approval Date - 13/12/2018 (Validity 5 years), Registration Number: NEPD-1690-678 (Jotun Indonesia);Jotun Durasol: Approval Date 19.12.2017 (Validity 5 years), Registration Numbers: NEPD-1481-497 (Jotun China); NEPD-1482-497 (Jotun Saudi Arabia); NEPD-1480-497 (Jotun Thailand); Approval Date - 05/03/2018 (Validity 5 years), Registration Number: NEPD -1519-521 (Jotun Boya).Solar Reflective Index (ASTM E1980) – the following Colors of Jotun Super Durable 2901, Jotun Super Durable 2903 and Jotun Super Durable 2905:Sunpath 84Couronne 45Sepia 39Dayspring 53Equinox 40Arc 52Meridian 90Starfall 36Above colors have 3rd party test reports; additional colors can be tested by request.Powder Coating: Jotun Super Durable 2901, Jotun Super Durable 2903 and Jotun Super Durable 2905 as manufactured by Jotun Powder CoatingsPerformance: Qualicoat Class 2/ AAMA 2604Natural Weathering: 3 to 5 years in FloridaFinish: Sahara texture Finish: SmoothGloss: Matt Gloss: SatinColor:Powder Coating: Jotun Durasol as manufactured by Jotun Powder CoatingsPerformance: Qualicoat Class 3/ AAMA 2605Natural Weathering: 10 years in Florida Finish: SmoothGloss: Matt Color:PART 3 – EXECUTIONEXAMINATIONA. Do not begin installation until substrates have been properly prepared.B. If substrate preparation is the responsibility of another installer, notify architect of unsatisfactory preparation before proceeding.PREPARATIONA. Clean surfaces thoroughly prior to installation.B. Prepare surfaces using the methods recommended by the Manufacturer for achieving the best result for the substrate under the project conditions.INSTALLATIONInstall in accordance with manufacturer's instructions and approved submittals.PROTECTIONA. Protect installed products until completion of project.B. Touch-up, repair or replace damaged products before Substantial Completion.END OF SECTION ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download