Riverside Page 1 of 14
Riverside FURNITURE
email: info@riverside-
Modern Gatherings Entertainment
Assembly Instructions
ASSEMBLY INSTRUCTIONS ITEMS NO. & DESCRIPTION 15340 ENTERTAINMENT CONSOLE 15344 BRIDGE & BACK PANEL 15347 LEFT PIER 15348 RIGHT PIER
Page 1 of 14
Made in Viet Nam
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have come loose inside the carton during shipment. Separate and count all parts, comparing to the Parts and Hardware Lists.
Parts List
No. Description
Sketch
Quantity
No. Description
Sketch
Quantity
A1
Left-Hand Pier
1
D
Back Panels
2
A2
Right-Hand Pier
1
E
B
Console
1
F
C
Bridge
1
G
Back Panel Rail
1
Top Back Rail
1
Door
2
Riverside FURNITURE
email: info@riverside-
Modern Gatherings Entertainment
Assembly Instructions
ASSEMBLY INSTRUCTIONS ITEMS NO. & DESCRIPTION 15340 ENTERTAINMENT CONSOLE 15344 BRIDGE & BACK PANEL 15347 LEFT PIER 15348 RIGHT PIER
Page 2 of 14
Made in Viet Nam
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have come loose inside the carton during shipment. Separate and count all parts, comparing to the Parts and Hardware Lists.
Hardware List
No. Description
Quantity No. Description
Quantity No. Description
Quantity
`? Allen Head Bolt
`? Hex Head Bolt
T-Wood Block
`? Allen Head Bolt
`? Allen Head Bolt
`? Connector Nut
`? Hex Head Bolt
`? Hex Head Bolt
`?` Hex Nut
Spacer Block 4 x 40 x 40mm
Door Bar Pull 915 x 25 x 60
Top Door Track 1725 x 35 x 5
`?` Spring Washer
` x 27 long x 12 OD
Bottom Door Track 1725 x 70 x 3
`?` Flat Washer
L-Door Stop 2 x 20 x 30
12mm Open Wrench
`?` Flat Washer
Flat Metal
4 x 100mm Straight Allen Wrench
`?` Flat Washer
`?` Plastic washer
Roller Assembly
4 x 110mm L-Allen Wrench
Furniture Anti-Tipping
Restraint
Riverside FURNITURE
email: info@riverside-
Modern Gatherings Entertainment
Assembly Instructions
ASSEMBLY INSTRUCTIONS ITEMS NO. & DESCRIPTION 15340 ENTERTAINMENT CONSOLE 15344 BRIDGE & BACK PANEL 15347 LEFT PIER 15348 RIGHT PIER
Page 3 of 14
Made in Viet Nam
IMPORTANT
In order to properly set-up and assemble the complete Modern Gathering Entertainment Wall System, the following steps should be followed. Listed directly below are the basic steps but the detailed instructions given on the following pages must be referenced for more complete set-up instructions. Two people are required in order to safely and properly assemble the Wall System.
Note #1: While unpacking each piece check all packaging materials for small parts which may have come loose during shipping. Do not discard any packaging materials until all parts and hardware have been accounted for.
Note #2: In order to simplify performing Step 7 below, as the TV Console and Pier Cabinets are being unpacked, place these pieces on their back and install the Bolts and Washers underneath the bottom front edges, as referenced in Step 7 below.
Step 1:
A. Unpack the TV Console (B) and move it to be near the wall where it will be used in the room. There should be a few inches left between the TV Console and wall.
B. Attach the Top Back Rail (F) for the Back Panel across the top back edge of the Console, using the Allen Head Bolts (H3) and the Flat Washers (H6). Tighten with the L-Allen Wrench (H25).
Step 2:
A: Unpack each Pier Cabinet.
B: Attach a T-Wood Block (H18) to the back of each Pier Cabinet with the Allen Head Bolts (H3) and the Plastic Washer (H9) as shown in the diagram. Tighten snug but not tight, with the Allen Wrench (H25). The T-Block must be able to be pivoted later.
C: Carefully move Pier Cabinets to the ends of the TV Console. Check that the top and base moldings of the Pier and Console are in line with each other. There are levelers mounted underneath the front corners of the TV Console and Pier Cabinets which can be used to align the TV Console and Pier Cabinets if needed.
Step 3: In order to minimize the risk of the Wall System accidentally tipping forward and causing personal injury and damage, it is highly recommended that the Wall System be anchored to the wall behind using the Furniture Tipping Restraints attached to the back of each Pier Cabinet and TV Console. Follow the instructions on the Tip Restraint package for mounting the Brackets but do not connect the straps until the Wall System has been completely set up.
Step 4: Connect the Pier Cabinets to the ends of the TV Console using the Allen Head Bolts (H2), Spring Washers (H5), Flat Washers (H6) and Connector Nuts (H4) as shown in the diagram. Tighten with the L-Allen Wrenches (H25).
Step 5: A. Unpack the Bridge and Back Panels. Carefully stand the Back Panels on their end, leaning the back side against the wall behind the TV Console. Installing the Back Panels will be the last step in setting up the wall system.
B. Attach Flat Metal (H16) to the top of the Bridge using the Allen Head Bolds (H1), Spring Washer (H5), Flat Washer (H7). Tighten with the L-Allen Wrench (H25).
Step 6: Using two people very carefully position the Bridge between the Pier Cabinets, resting the Flat Metal attached on each end of the Bridge on the top of the Piers, and connect units together using the Allen Head Bolts (H2), Spring Washers (H5), Flat Washers (H6) and Connector Nuts (H4) as shown in the diagram. Tighten with the L-Allen Wrench (H25).
Step 7: If not already installed at the beginning of the assembly, partially install the twelve Hex Head Bolts (H10), Spring Washers (H5), and Flat Washers (H7) into the inserts located underneath the front edge of the TV Console and both Pier Cabinets. Only install Bolts a couple turns each until the next step.
Step 8: Install the Bottom Door Track (H22), with the narrow leg of the 'L' pointed up, onto the Hex-Head Bolts, on top of the Flat Washers installed in the previous step as shown. After sliding the Track onto the Bolts, move the Track to the right to lock in position. Tighten Bolts with the Open Wrench (H23).
Step 9: Attach one Upper Door Track (H21) on the left-hand side using the Hex Head Bolts (H12), Flat Washers (H7) and Steel Sleeves (H14) into the four middle holes of the track. Attach one L-Door Stop (H15) at the left-hand end of the track using the same Bolt, Washer and Sleeve as before. Tighten with the Open Wrench.
Step 10: Attach the Door Roller Assemblies (H17) to both Doors (G) using the Hex Head Bolts (H11), Flat Washers (H7), Flat Washers (H8) (Note: The Flat Washers is bigger and puts after the door), Spring Washers (H5) and Nuts (H13) but do not fully tighten these Bolts because adjustments will be made after the doors are hung. Assemble the Door Bar Pulls (H20) to the outside of the Doors using the Allen Head Bolts (H2), Spring Washes (H5), Flat Washers (H7). Tighten with L-Allen Wrench (H25).
Step 11: Slide both Doors (G) onto the Top Door Track and Bottom Door Track, sliding the doors all the way to the left end until they stop.
Step 12: Install the other Top Door Track onto the Right Hand Pier and across the Bridge as in Step 9. Slide the Doors apart.
Step 13: To set the Door tracking, place the two Spacer Blocks (H19) between the top edge of the Left Hand Door and bottom edge of the Top Door Track. Hold down on each Door Roller while also lifting the Door. Tighten the Bolts securing the Door Roller Assembly to the Door. Repeat for the Right Hand Door.
Step 14. Attach the other three L-Door Stops (H15) at the ends of the tracks positioned as shown, using the same Bolts and Washers as used to mount the Upper Door Tracks in Step 9. Slide the two Doors together, adjusting the middle Door Stops where the Doors touch each other at the middle. Slide each Door to the outside end of the completed wall assembly, adjusting the Door Stops so the doors are flush to the outside ends.
Step 15: Slide both Doors together again to check for proper alignment and for uneven gaps between the doors from the top to the bottom. If the Doors are not aligned correctly, loosen the bolts attaching one of the Rollers on one Door, making necessary adjustments and retighten the bolts.
Step 16: Working from the front of the Entertainment Wall System, reach over the TV Console, lift and install one of the lower Back Panels (D) into the Top Back Rail (F) mounted on the back of the TV Console. Pivot the T-Wood Block at each end to be vertical over the top edge of the Back Panel.
Step 17: Place the Back Panel Rail (E) onto the top edge of the Lower Back Panel. Lift the upper Back Panel, placing the top edge into the rail mounted at the lower back edge of the Bridge, pull forward and then lower the bottom edge into the top groove of the Back Panel Rail.
Riverside FURNITURE
email: info@riverside-
Modern Gatherings Entertainment
Assembly Instructions
ASSEMBLY INSTRUCTIONS ITEMS NO. & DESCRIPTION 15340 ENTERTAINMENT CONSOLE 15344 BRIDGE & BACK PANEL 15347 LEFT PIER 15348 RIGHT PIER
Page 4 of 14
Made in Viet Nam
Step 1:
A. Unpack the TV Console (B) and move it to be near the wall where it will be used in the room. There should be a few inches left between the TV Console and wall.
B. Attach the Top Back Rail (F) for the Back Panel across the top back edge of the Console, using the Allen Head Bolts (H3) and the Flat Washers (H6). Tighten with the L-Allen Wrench (H25).
H9
18
A1
A2
H3 H25
B
H6 H3
F
H25
Step 2: A: Unpack each Pier Cabinet. B: Attach a T-Wood Block (H18) to the back of each Pier Cabinet with the Allen Head Bolts (H3) and the Plastic Washer (H9) as shown in the diagram. Tighten snug but not tight, with the Allen Wrench (H25). The T-Block must be able to be pivoted later. C: Carefully move Pier Cabinets to the ends of the TV Console. Check that the top and base moldings of the Pier and Console are in line with each other. There are levelers mounted underneath the front corners of the TV Console and Pier Cabinets which can be used to align the TV Console and Pier Cabinets if needed.
Riverside FURNITURE
email: info@riverside-
Modern Gatherings Entertainment
Assembly Instructions
ASSEMBLY INSTRUCTIONS ITEMS NO. & DESCRIPTION 15340 ENTERTAINMENT CONSOLE 15344 BRIDGE & BACK PANEL 15347 LEFT PIER 15348 RIGHT PIER
Page 5 of 14
Made in Viet Nam
Step 3: In order to minimize the risk of the Wall System accidentally tipping forward and causing personal injury and damage, it is highly recommended that the Wall System be anchored to the wall behind using the Furniture Tipping Restraints attached to the back of each Pier Cabinet and TV Console. Follow the instructions on the Tip Restraint package for mounting the Brackets but do not connect the straps until the Wall System has been completely set up.
Step 4: Connect the Pier Cabinets to the ends of the TV Console using the Allen Head Bolts (H2), Spring Washers (H5), Flat Washers (H6) and Connector Nuts (H4) as shown in the diagram. Tighten with the L-Allen Wrenches (H25).
A2
A1 B
H25 H5
H6 H2
H4 H25
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- discontinued furniture contract
- podc t obsolescence e mouser electronics
- bourns model ci100505 series multilayer chip inductors to be discontinued
- riverside page 3 of 11 riverside furniture
- bl7591 36967 trpt6786 75880 trpt6786 75870 bchh4868 10268
- assembly instructions for discontinued ikea furniture
- riverside page 1 of 4 riverside furniture
- podc t obsolescence e
- rc sscc memo digi key
- riverside page 1 of 3 riverside furniture
Related searches
- step 1 of photosynthesis
- circular 1 of 2016
- full page map of china
- male femininity page 1 the new age
- 1 of water psi
- chapter 1 of the outsiders
- riverside county office of education
- riverside county dept of education
- riverside co office of education
- riverside county school of education
- riverside county department of education
- 1 of a kind