JustAnswer
|Trouble Code: U0105 (6.6L V8 VIN 2 Auto) |Print this code data[pic] |
|Lost Communication With Fuel Injector Control Module (FICM) | |
OBD II Monitor Type: CCM Details
Indicators: MIL Details
Trouble Code Conditions:
• Voltage supplied to the modules is in the normal operating voltage range.
• The engine is running.
Possible Causes:
• A poor connection at the inoperative module may cause this code to set.
• An improperly powered module may cause this code to set.
2005 GMC Sierra 3500 - Communications - Computer/Integrating Systems - DTC U0100-U0299 (Diesel Engine)2005 GMC Sierra 3500 - Communications - Computer/Integrating Systems - DTC U0100-U0299 (HP2)
Top of Form
[pic]
[pic][pic]PATH: Diagnostics > Diagnostic Routines > Communications > Computer/Integrating Systems > DTC U0100-U0299 (Diesel Engine)
DTC U0100-U0299 (Diesel Engine)
|NOTE |
|Applicable vehicles: |
|Sierra, Silverado (VIN C/K) |
DTC U0100-U0299 (Diesel Engine)
Circuit Description
Modules connected to the high speed GMCAN serial data circuits monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an availability indication of the transmitter module. Each message contains the identification number of the transmitter module. A module with a high speed GMCAN serial data circuits malfunction or which loses power during the current ignition cycle will have a Loss of Communication DTC set by other modules that depend on information from that failed module. If any of the high speed GMCAN circuits are shorted to battery voltage, ground or between them, no communication is possible on high speed GMCAN serial data bus, and a DTC U0073 is set.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
• DTC U0100 Lost Communication With Engine Control Module (ECM)
• DTC U0101 Lost Communication With Transmission Control Module (TCM)
• DTC U0106 Lost Communication With Glow Plug Control Module (GPCM)
• DTC U0105 Lost Communication With Fuel Injector Control Module (FICM)
Conditions for Running the DTCs
• Voltage supplied to the modules is in the normal operating voltage range.
• The engine is running.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received.
Action Taken When the DTC Sets
• The module uses a default value for the missing parameter.
• The malfunction indicator lamp (MIL) will illuminate on the second consecutive ignition cycle that the diagnostic runs and fails, for the type B DTCs. For a detailed description about DTC types, refer to Diagnostic Trouble Code (DTC) Type Definitions for the 6.6L (LLY) engine.
Conditions for Clearing the MIL/DTC
The MIL/DTC clearing depends on DTC type. For information about DTC types, refer to Diagnostic Trouble Code (DTC) Types for the 6.6L (LLY) engine.
• DTC type B
o The MIL clears after 3 ignition cycles when the malfunction is no longer present.
o A current DTC clears when the malfunction is no longer present.
o A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.
• DTC type C
o A current DTC clears when the malfunction is no longer present.
o A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.
Diagnostic Aids
• A poor connection at the inoperative module may cause this code to set.
• An improperly powered module may cause this code to set.
Test Description
The numbers below refer to the step numbers on the diagnostic table:
9. The modules which can communicate indicate the module which cannot communicate. You must clear the DTC from these modules to avoid future misdiagnosis.
|Step |Action |Yes |No |
|Schematic Reference: Data Link Connector Schematics |
|Connector End View Reference: Master Electrical Component List |
|1 |Did you perform the Diagnostic System Check - Vehicle? |Go to Step 2 |Go to Diagnostic |
| | | |System Check - |
| | | |Vehicle |
|2 |WARNING |Go to Step 8 |Go to Step 3 |
| | | | |
| |Important: Use the DTC descriptor list in order to determine which module is| | |
| |not communicating on high speed GMCAN serial data bus. | | |
| | | | |
| |Turn the ignition ON, with the engine OFF. | | |
| |Test the following circuits of the module that is not communicating on high | | |
| |speed GMCAN serial data bus for an open or a short to ground: | | |
| |The battery positive voltage input circuits | | |
| |The battery positive voltage output circuits | | |
| |The ignition voltage input circuits | | |
| |The ignition voltage output circuits | | |
| |The switched battery positive voltage circuits | | |
| |Refer to the following: | | |
| |Control Module References for the applicable schematic | | |
| |Circuit Testing | | |
| |Wiring Repairs | | |
| |Did you find and correct the condition? | | |
|3 |Turn OFF the ignition. |Go to Step 8 |Go to Step 4 |
| |Test the ground circuits of the module that is not communicating on high | | |
| |speed GMCAN serial data bus for an open. | | |
| |Refer to the following: | | |
| |Control Module References for the applicable schematic | | |
| |Circuit Testing | | |
| |Wiring Repairs | | |
| |Did you find and correct the condition? | | |
|4 |Test the high speed GMCAN serial data circuits of the module that is not |Go to Step 8 |Go to Step 5 |
| |communicating on high speed GMCAN serial data bus for an open. Refer to | | |
| |Circuit Testing and Wiring Repairs . | | |
| |Did you find and correct the condition? | | |
|5 |Inspect the harness connectors of the module that is not communicating on |Go to Step 8 |Go to Step 6 |
| |high speed GMCAN serial data bus for poor connections and terminal tension | | |
| |at the following circuits: | | |
| |The battery positive voltage input circuits | | |
| |The battery positive voltage output circuits | | |
| |The ignition voltage input circuits | | |
| |The ignition voltage output circuits | | |
| |The switched battery positive voltage supply circuits | | |
| |The ground circuits | | |
| |The high speed GMCAN serial data circuits | | |
| |Refer to the following: | | |
| |Control Module References for the applicable schematic | | |
| |Testing for Intermittent Conditions and Poor Connections | | |
| |Connector Repairs | | |
| |Did you find and correct the condition? | | |
|6 |Replace the module that is not communicating on high speed GMCAN serial data|Go to Step 7 |-- |
| |bus. Refer to Control Module References for replacement, setup, and | | |
| |programming. | | |
| |Did you complete the replacement? | | |
|7 |Install a scan tool. |Go to Diagnostic |Go to Step 8 |
| |Turn ON the ignition with the engine OFF. |Trouble Code (DTC) | |
| |Select the Display DTCs function for the module which was not communicating.|List - Vehicle | |
| |Does the scan tool display any DTCs which do not begin with a "U"? | | |
|8 |Select the Display DTCs function for the modules which had the Loss of |Go to Diagnostic |Go to Step 9 |
| |Communications DTC set. |Trouble Code (DTC) | |
| |Does the scan tool display any DTCs which do not begin with a "U"? |List - Vehicle | |
|9 |Use the scan tool in order to clear the DTCs. |System OK |-- |
| |Continue diagnosing or clearing the DTCs until all the modules have been | | |
| |diagnosed and all the DTCs have been cleared. | | |
| |Did you complete the action? | | |
Bottom of Form
Top of Form
[pic]
[pic][pic]PATH: Diagnostics > Diagnostic Routines > Communications > Computer/Integrating Systems > DTC U0100-U0299 (HP2)
DTC U0100-U0299 (HP2)
|NOTE |
|Applicable vehicles: |
|Sierra, Silverado (VIN C/K) |
DTC U0100-U0299 (HP2)
Circuit Description
Modules connected to the high speed GMLAN serial data circuits monitor for serial data communications during normal vehicle operation. There are two 120 ohm resistors between the GMLAN serial data (+) and (-) circuits. One is internal to the powertrain control module (PCM) and the other is internal to the energy storage control module (ESCM). When tested between the GMLAN serial data (+) and (-) circuits at the data link connector (DLC) with the ignition key OFF, normal resistance is 55-65 ohms.
Operating information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be exchanged on the serial data circuits. The messages are supervised and also, some periodic messages are used by the receiver module as an availability indication of the transmitter module. Each message contains the identification number of the transmitter module. When a message that indicates the availability of the transmitter module is not received, the receiver module sets a DTC.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
• DTC U0111 Lost Communication With Energy Storage Control Module (ESCM)
• DTC U0120 Lost Communication With Starter/Generator Control Module (SGCM)
• DTC U0131 Lost Communication With Electro-Hydraulic Power Steering (EHPS) Module
• DTC U0293 Lost Communication With Hybrid Control Module (HCM)
Conditions for Running the DTCs
Voltage supplied to the modules is in the normal operating voltage range.
Conditions for Setting the DTC
A supervised periodic message that includes the transmitter module availability has not been received by powertrain control module (PCM) from 1 or more of the high speed GMLAN modules.
Action Taken When the DTC Sets
• The malfunction indicator lamp (MIL) may illuminate.
• The Hybrid Engine Idle Off feature may not operate properly.
Conditions for Clearing the MIL/DTC
• The MIL clears after 3 ignition cycles when the malfunction is no longer present.
• A current DTC clears when the malfunction is no longer present.
• A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.
Diagnostic Aids
The following conditions may cause the DTC to set:
• A poor connection or terminal tension at a GMLAN module
• An intermittent open on either high speed GMLAN serial data circuit
• An open voltage or ground circuit to a module
• An internal module malfunction
• A short between the GMLAN serial data circuits
• A short to voltage or ground on either of the GMLAN serial data circuits
Test Description
The number below refers to the step number on the diagnostic table.
13. A resistance out of range will indicate 1 of several specific faults as follows:
o A high resistance indicates an open or high resistance in either of the high speed GMLAN serial data circuits between C 206 and the modules, including all module internals, circuits between, and module terminal tension.
o A low resistance indicates a short between the high speed GMLAN serial data circuits, including module internals.
o Infinite resistance indicates an open between the DLC and C 206 in either of the high speed GMLAN serial data circuits.
|Step |Action |Values |Yes |No |
|Schematic Reference: Data Link Connector Schematics |
|Connector End View Reference: Master Electrical Component List and Inline Harness Connector End Views in Wiring Systems |
|1 |Did you perform the Diagnostic System Check - Vehicle? |-- |Go to Step 2 |Go to Diagnostic |
| | | | |System Check - |
| | | | |Vehicle in Vehicle|
| | | | |DTC Information |
|2 |WARNING |55-65 ohms |Go to Step 3 |Go to Step 13 |
| | | | | |
| |Important: Use the DMM MIN/MAX function to capture intermittent | | | |
| |conditions. | | | |
| | | | | |
| |Ignition OFF. | | | |
| |Test the resistance between data link connector (DLC) pins 14 and 6. | | | |
| |Is the resistance within the specified range? | | | |
|3 |Turn ON the ignition, with the engine OFF. |-- |Go to Step 9 |Go to Step 4 |
| |Install the scan tool with the CANdi module attached to it. | | | |
| |Attempt to communicate with the following modules: | | | |
| |Energy storage control module (ESCM) | | | |
| |Starter/generator control module (SGCM) | | | |
| |Electro-hydraulic power steering (EHPS) module | | | |
| |Does the scan tool communicate with any of the listed modules? | | | |
|4 |WARNING |-- |Go to Step 5 |Go to Step 9 |
| | | | | |
| |Important: Turn ON the ignition, with the engine OFF, when testing for | | | |
| |a short to voltage. Use the DMM MIN/MAX function to capture | | | |
| |intermittent conditions. | | | |
| | | | | |
| |Test the high speed GMLAN serial data circuits at the DLC for: | | | |
| |A short to ground | | | |
| |A short to voltage | | | |
| |Refer to the following in Wiring Systems: | | | |
| |Testing for Intermittent Conditions and Poor Connections | | | |
| |Circuit Testing | | | |
| |Did you find any of the above conditions? | | | |
|5 |Disconnect the high speed GMLAN modules, one at a time, in the |-- |Go to Step 8 |Go to Step 6 |
| |following order testing for the short found in the previous step after | | | |
| |each disconnect: | | | |
| |powertrain control module (PCM) | | | |
| |Hybrid control module (HCM) | | | |
| |EHPS | | | |
| |SGCM | | | |
| |ESCM | | | |
| |Test the high speed GMLAN serial data circuits at the DLC for the short| | | |
| |found at step 4. | | | |
| |Does the short found at step 4 at DLC still exist? | | | |
|6 |WARNING |-- |Go to Step 15 |Go to Step 7 |
| | | | | |
| |Important: If only PCM was disconnected on step 5, answer No at this | | | |
| |step. | | | |
| | | | | |
| |Test the high speed GMLAN serial data circuits between the last 2 | | | |
| |disconnected modules for the short found at step 4. | | | |
| |Did you find and correct the condition? | | | |
|7 |Consider the last disconnected module as the non-communicating module |-- |Go to Step 12 |-- |
| |for the following steps. | | | |
|8 |Repair the high speed GMLAN serial data circuits between DLC and |-- |Go to Step 15 |-- |
| |ESCM/SGCM for the short found in step 4. | | | |
| |Refer to the following in Wiring Systems: | | | |
| |Connector Repairs | | | |
| |GMLAN Wiring Repairs | | | |
| |Did you complete the repair? | | | |
|9 |WARNING |-- |Go to Step 15 |Go to Step 10 |
| | | | | |
| |Important: Use the DTC Descriptors list in order to determine which | | | |
| |module is not communicating. | | | |
| | | | | |
| |Test the following circuits of the module that is not communicating for| | | |
| |an open or a short to ground: | | | |
| |The battery positive voltage input circuits | | | |
| |The battery positive voltage output circuits | | | |
| |The ignition voltage input circuits | | | |
| |The ignition voltage output circuits | | | |
| |The switched battery positive voltage circuits | | | |
| |Refer to the following: | | | |
| |Control Module References for the applicable schematic | | | |
| |Circuit Testing in Wiring Systems | | | |
| |Wiring Repairs in Wiring Systems | | | |
| |Did you find and correct the condition? | | | |
|10 |Turn OFF the ignition. |-- |Go to Step 15 |Go to Step 11 |
| |Test the ground circuits of the module that is not communicating for an| | | |
| |open. | | | |
| |Refer to the following: | | | |
| |Control Module References for the applicable schematic | | | |
| |Circuit Testing in Wiring Systems | | | |
| |Wiring Repairs in Wiring Systems | | | |
| |Did you find and correct the condition? | | | |
|11 |Test the high speed GMLAN serial data circuits of the module that is |-- |Go to Step 15 |Go to Step 12 |
| |not communicating for an open. Refer to Circuit Testing and Wiring | | | |
| |Repairs in Wiring Systems. | | | |
| |Did you find and correct the condition? | | | |
|12 |Inspect the harness connectors of the module that is not communicating |-- |Go to Step 15 |Go to Step 14 |
| |or is causing the malfunction for poor connections and terminal tension| | | |
| |at the following circuits: | | | |
| |The battery positive voltage input circuits | | | |
| |The battery positive voltage output circuits | | | |
| |The ignition voltage input circuits | | | |
| |The ignition voltage output circuits | | | |
| |The switched battery positive voltage supply circuits | | | |
| |The ground circuits | | | |
| |The high speed GMLAN serial data circuits | | | |
| |Refer to the following: | | | |
| |Control Module References for the applicable schematic | | | |
| |Testing for Intermittent Conditions and Poor Connections in Wiring | | | |
| |Systems | | | |
| |Connector Repairs in Wiring Systems | | | |
| |Did you find and correct the condition? | | | |
|13 |WARNING |-- |Go to Step 15 |Go to Step 12 |
| | | | | |
| |Important: A circuit or module terminal tension is the likely fault. If| | | |
| |a module does cause the malfunction, proceed to step 12. | | | |
| | | | | |
| |Repair the high speed GMLAN serial data (+) or (-) circuit as | | | |
| |necessary. | | | |
| |Did you find and correct the condition with a wiring repair? | | | |
|14 |Replace the module that is not communicating. Refer to Control Module |-- |Go to Step 15 |-- |
| |References for replacement, setup, and programming. | | | |
| |Did you complete the replacement? | | | |
|15 |Install a scan tool. |-- |Go to Diagnostic |Go to Step 16 |
| |Turn ON the ignition with the engine OFF. | |Trouble Code (DTC)| |
| |Select the Display DTCs function for the module which was not | |List - Vehicle in | |
| |communicating. | |Vehicle DTC | |
| |Does the scan tool display any DTCs which do not begin with a "U"? | |Information | |
|16 |Select the Display DTCs function for the modules which had the Loss of |-- |Go to Diagnostic |Go to Step 17 |
| |Communications DTC set. | |Trouble Code (DTC)| |
| |Does the scan tool display any DTCs which do not begin with a "U"? | |List - Vehicle in | |
| | | |Vehicle DTC | |
| | | |Information | |
|17 |Use the scan tool in order to clear the DTCs. |-- |System OK |-- |
| |Continue diagnosing or clearing the DTCs until all the modules have | | | |
| |been diagnosed and all the DTCs have been cleared. | | | |
| |Did you complete the action? | | | |
Bottom of Form
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.