Chapter 2 Thermodynamics of Combustion
Chapter 2
Thermodynamics of Combustion
2.1
Properties of Mixtures
The thermal properties of a pure substance are described by quantities including
internal energy, u, enthalpy, h, specific heat, cp, etc. Combustion systems consist of
many different gases, so the thermodynamic properties of a mixture result from a
combination of the properties of all of the individual gas species. The ideal gas law
is assumed for gaseous mixtures, allowing the ideal gas relations to be applied to
each gas component. Starting with a mixture of K different gases, the total mass, m,
of the system is
m?
K
X
mi ;
(2.1)
i?1
where mi is the mass of species i. The total number of moles in the system, N, is
N?
K
X
Ni ;
(2.2)
i?1
where Ni is the number of moles of species i in the system. Mass fraction, yi, and
mole fraction, xi, describe the relative amount of a given species. Their definitions
are given by
yi
mi
m
and xi
Ni
;
N
(2.3)
where i ? 1,2,. . .,K. By definition,
K
X
i?1
yi ? 1
and
K
X
xi ? 1:
i?1
S. McAllister et al., Fundamentals of Combustion Processes,
Mechanical Engineering Series, DOI 10.1007/978-1-4419-7943-8_2,
# Springer Science+Business Media, LLC 2011
15
16
2 Thermodynamics of Combustion
With Mi denoting the molecular mass of species i, the average molecular mass, M,
of the mixture is determined by
P
Ni Mi X
m
?
M? ? i
xi M i :
(2.4)
N
N
i
From Dalton¡¯s law of additive pressures and Amagat¡¯s law of additive volumes
along with the ideal gas law, the mole fraction of a species in a mixture can be found
from the partial pressure of that species as
Pi Ni Vi
? ? ? xi ;
P
N
V
(2.5)
where Pi is the partial pressure of species i, P is the total pressure of the gaseous
mixture, Vi the partial volume of species i, and V is the total volume of the mixture.
The average intrinsic properties of a mixture can be classified using either a molar
base or a mass base. For instance, the internal energy per unit mass of a mixture, u,
is determined by summing the internal energy per unit mass for each species
weighted by the mass fraction of the species.
P
mi ui X
U
i
u? ?
?
y i ui ;
(2.6)
m
m
i
where U is the total internal energy of the mixture and ui is the internal energy per
mass of species i. Similarly, enthalpy per unit mass of mixture is
X
h?
y i hi
i
and specific heat at constant pressure per unit mass of mixture is
cp ?
X
yi cp;i :
i
A molar base property, often denoted with a ^ over bar, is determined by the sum
of the species property per mole for each species weighted by the species mole
fraction, such as internal energy per mole of mixture
X
u^ ?
xi u^i ;
i
enthalpy per mole of mixture
h^ ?
X
i
xi h^i ;
2.2 Combustion Stoichiometry
17
and entropy per mole of mixture
s^ ?
X
xi s^i :
i
Assuming constant specific heats during a thermodynamic process, changes of energy,
enthalpy, and entropy of an individual species per unit mass are described as follows:
Dui ? cv;i ?T2 T1 ?
(2.7)
Dhi ? cp;i ?T2 T1 ?
(2.8)
Dsi ? cp;i ln
T2
Pi;2
Ri ln
T1
Pi;1
(2.9)
Pi,1 and Pi,2 denote the partial pressures of species i at state 1 and state 2, respectively.
Ri is the gas constant for species i (Ri ? R^u =Mi ? universal gas constant/molecular
mass of species i). The overall change of entropy for a combustion system is
DS ?
X
mi Dsi :
i
A summary of the thermodynamic properties of mixtures is provided at the end
of the chapter.
2.2
Combustion Stoichiometry
For a given combustion device, say a piston engine, how much fuel and air should
be injected in order to completely burn both? This question can be answered by
balancing the combustion reaction equation for a particular fuel. A stoichiometric
mixture contains the exact amount of fuel and oxidizer such that after combustion is
completed, all the fuel and oxidizer are consumed to form products. This ideal
mixture approximately yields the maximum flame temperature, as all the energy
released from combustion is used to heat the products. For example, the following
reaction equation can be written for balancing methane-air combustion
79
CH4 ? ? O2 ? N2 ! ?CO2 ? ?H2 O ? ?N2 ;
(2.10)
21
where air consisting of 21% O2 and 79% N2 is assumed.1 The coefficients associated
with each species in the above equation are unknown. By balancing the atomic
18
2 Thermodynamics of Combustion
abundance on both the reactant and product sides, one can find the coefficient
for each species. For instance, let¡¯s determine the coefficient for CO2: on the reactant
side, we have 1 mol of C atoms; hence the product side should also have 1 mol of
C atoms. The coefficient of CO2 is therefore unity. Using this procedure we can
determine all the coefficients. These coefficients are called the reaction stoichiometric
coefficients. For stoichiometric methane combustion with air, the balanced reaction
equation reads:
CH4 ? 2?O2 ? 3:76N2 ? ! 1CO2 ? 2H2 O ? 7:52N2 :
(2.11)
Note that on the reactant side there are 2¡¤(1 + 3.76) or 9.52 mol of air and
its molecular mass is 28.96 kg/kmol. In this text, the reactions are balanced using
1 mol of fuel. This is done here to simplify the calculations of the heat of reaction
and flame temperature later in the chapter. Combustion stoichiometry for a general
hydrocarbon fuel, Ca Hb Og , with air can be expressed as
b g
b
b g
Ca Hb Og ? a? ?O2 ?3:76N2 ?!aCO2 ? H2 O?3:76 a? N2 : (2.12)
4 2
2
4 2
The amount of air required for combusting a stoichiometric mixture is called
stoichiometric or theoretical air. The above formula is for a single-component fuel
and cannot be applied to a fuel consisting of multiple components. There are two
typical approaches for systems with multiple fuels. Examples are given here for a
fuel mixture containing 95% methane and 5% hydrogen. The first method develops
the stoichiometry of combustion using the general principle of atomic balance,
making sure that the total number of each type of atom (C, H, N, O) is the same in
the products and the reactants.
0:95CH4 ? 0:05H2 ? 1:925?O2 ? 3:76N2 ? !
0:95CO2 ? 1:95H2 O ? 7:238N2 :
The other method of balancing a fuel mixture is to first develop stoichiometry
relations for CH4 and H2 individually:
CH4 ? 2?O2 ? 3:76N2 ? ! CO2 ? 2H2 O ? 2 3:76N2
H2 ? 0:5?O2 ? 3:76N2 ? ! H2 O ? 0:5 3:76N2
Then, multiply the individual stoichiometry equations by the mole fractions of the
fuel components and add them:
2.2 Combustion Stoichiometry
19
0:95 fCH4 ? 2?O2 ? 3:76N2 ? ! CO2 ? 2H2 O ? 2 3:76N2 g
0:05 fH2 ? 0:5?O2 ? 3:76N2 ? ! H2 O ? 0:5 3:76N2 g
)0:95CH4 ? 0:05H2 ? 1:925?O2 ? 3:76N2 ? !
0:95CO2 ? 1:95H2 O ? 7:238N2
2.2.1
Methods of Quantifying Fuel and Air Content
of Combustible Mixtures
In practice, fuels are often combusted with an amount of air different from the
stoichiometric ratio. If less air than the stoichiometric amount is used, the mixture is
described as fuel rich. If excess air is used, the mixture is described as fuel lean. For
this reason, it is convenient to quantify the combustible mixture using one of the
following commonly used methods:
Fuel-Air Ratio (FAR): The fuel-air ratio, f, is given by
f ?
mf
;
ma
(2.13)
where mf and ma are the respective masses of the fuel and the air. For a stoichiometric mixture, Eq. 2.13 becomes
mf
Mf
?
;
fs ?
ma stoichiometric ?a ? b4 2g? 4:76 Mair
(2.14)
where Mf and Mair (~28.84 kg/kmol) are the average masses per mole of fuel and air,
respectively. The range of f is bounded by zero and 1. Most hydrocarbon fuels have
a stoichiometric fuel-air ratio, fs, in the range of 0.05¨C0.07. The air-fuel ratio (AFR) is
also used to describe a combustible mixture and is simply the reciprocal of FAR, as
AFR ? 1/f. For instance, the stoichiometric AFR of gasoline is about 14.7. For most
hydrocarbon fuels, 14¨C20 kg of air is needed for complete combustion of 1 kg of fuel.
Equivalence Ratio: Normalizing the actual fuel-air ratio by the stoichiometric fuelair ratio gives the equivalence ratio, f.
f?
f
mas Nas
NO2s
?
?
?
fs
ma
Na
NO2;a
(2.15)
The subscript s indicates a value at the stoichiometric condition. f 1 is a rich mixture. Similar to f,
the range of f is bounded by zero and 1 corresponding to the limits of pure air and
fuel respectively. Note that equivalence ratio is a normalized quantity that provides
the information regarding the content of the combustion mixture. An alternative
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- mole tables nova blogs
- mole calculations multiple choice review psi chemistry name
- mole ratios seattle public schools
- calculating empirical and molecular formulas
- moles stoichiometry cheat sheet
- molar ratios and mass relationships in chemical equations
- mole calculation worksheet everett community college
- chapter 13 stoichiometry
- topic 9 chemical calculations iii stoichiometry
- stoichiometry calculations with chemical formulas and
Related searches
- chapter 2 developmental psychology quizlet
- medical terminology chapter 2 terms
- physics chapter 2 practice test
- psychology chapter 2 quizlet
- medical terminology chapter 2 test
- medical terminology chapter 2 review
- chapter 2 medical terminology quiz
- chapter 4.2 overview of photosynthesis
- chapter 4 2 overview of photosynthesis
- future of combustion engines
- inventor of combustion engine
- chapter 2 of genesis