REPORT DOCUMENTATION PAGE - DTIC

REPORT DOCUMENTATION PAGE

Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 1 hour per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing this collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to Department of Defense, Washington Headquarters Services, Directorate for Information Operations and Reports (0704-0188), 1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 222024302. Respondents should be aware that notwithstanding any other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS.

1. REPORT DATE (DD-MM-YYYY)

2. REPORT TYPE

3. DATES COVERED (From - To)

30-11-2012

Research Report

05-01-2010 to 30-11-2012

4. TITLE AND SUBTITLE

5a. CONTRACT NUMBER

Ballistics of the 30-06 Rifle Cartridge

6B. AaUlTlHiOsRt(iSc) s of the 30-06 Rifle Cartridge MBicahlaleilsCtoiucrstneoyf, AthmyeC3o0urt-n0ey6 Rifle Cartridge

5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER

7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES)

AND ADDRESS(ES) DFRL U.S. Air Force Academy 2354 Fairchild Drive

USAF Academy, CO 80840

8. PERFORMING ORGANIZATION REPORT NUMBER

9. SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES)

10. SPONSOR/MONITOR'S ACRONYM(S)

12. DISTRIBUTION / AVAILABILITY STATEMENT

Approved for public release; distribution unlimited

11. SPONSOR/MONITOR'S REPORT NUMBER(S)

13. SUPPLEMENTARY NOTES

This paper describes the internal, external, and terminal ballistics of the 30-06 rifle cartridge. With cartridge case capacity of 68-70 grains of water and operating pressures up to 60,000 psi, the 30-06 launches 110-220 grain bullets with muzzle velocities between 3400 fps and 2400 fps, respectively. Low-drag bullets are available which make the 30-06 an effective and capable choice for target and anti-personnel use out to 1000 yards, but longer range applications are challenging due to the sonic transition. With an appropriate bullet choice, the 30-06 penetrates a variety of commonly encountered barriers. It also penetrates soft body armors and can deliver significant wounding effects even when stopped by hard body armor. At shorter ranges, wounding effects in human and deer-sized living targets are impressive and yield rapid incapacitation.

15. SUBJECT TERMS

30-06, bullet, trajectory, muzzle velocity, impact energy, temporary cavity, wound ballistics, hydrostatic shock

16. SECURITY CLASSIFICATION OF:

a. REPORT

unclassified

b. ABSTRACT

unclassified

c. THIS PAGE

unclassified

17. LIMITATION OF ABSTRACT

Same as Report (SAR)

18. NUMBER OF PAGES

8

19a. NAME OF RESPONSIBLE PERSON

Michael Courtney

19b. TELEPHONE NUMBER (include area

code)

719-333-8113

Standard Form 298 (Rev. 8-98)

Prescribed by ANSI Std. Z39.18

Ballistics of the 30-06 Rifle Cartridge

Michael W. Courtney, Ph.D., U.S. Air Force Academy, 2354 Fairchild Drive, USAF Academy, CO, 80840-6210 Michael.Courtney@usafa.edu

Amy C. Courtney, Ph.D., BTG Research, PO Box 62541, Colorado Springs, CO 80962-2541 amy_courtney@post.harvard.edu

Abstract: This paper describes the internal, external, and terminal ballistics of the 30-06 rifle cartridge. With cartridge case capacity of 68-70 grains of water and operating pressures up to 60,000 psi, the 30-06 launches 110220 grain bullets with muzzle velocities between 3400 fps and 2400 fps, respectively. Low-drag bullets are available which make the 30-06 an effective and capable choice for target and anti-personnel use out to 1000 yards, but longer range applications are challenging due to the sonic transition. With an appropriate bullet choice, the 30-06 penetrates a variety of commonly encountered barriers. It also penetrates soft body armors and can deliver significant wounding effects even when stopped by hard body armor. At shorter ranges, wounding effects in human and deer-sized living targets are impressive and yield rapid incapacitation.

Keywords: 30-06, bullet, trajectory, muzzle velocity, impact energy, temporary cavity, wound ballistics, hydrostatic shock

I. Introduction The 30-06 has a long history as an effective cartridge for military applications and still finds occasional use in law enforcement and self-defense. Introduced in 1906 in the 1903 Springfield bolt-action rifle and later chambered in the semi-automatic M1 Garand rifle, it served as the primary rifle cartridge for the US military for nearly 50 years and continued to find use in US Marine sniper rifles (Winchester Model 70 bolt action) until well into the Vietnam war. The M24 sniper rifle (Remington 700 bolt action) in current service by the US Army was originally specified to use the 30-06 cartridge, but was later changed to the 7.62x51mm and .300 Winchester Magnum cartridges.

The United States Air Force Academy Cadet Honor Guard still carries M1 Garand Rifles chambered in 30-06, (1) and rifles chambered in the cartridge also still see wide use in ROTC drill and training. The Civilian Marksmanship Program (CMP), chartered by the U.S. Congress to promote marksmanship among civilians who might be later called to serve in the U.S. Military, distributes surplus Model 1903 Springfield, Model 1917 Enfield, and M1 Garand rifles chambered in 30-06 and sees a considerable demand for these rifles, as well as 30-06 ammunition. (2)

Bullet Hodgdon Speer Hornady Nosler Barnes

Weight (3)

(4)

(5)

(6)

(7)

(grains) velocity velocity velocity velocity velocity

(fps) (fps) (fps) (fps) (fps)

110

3505 3356 3500 N/A 3471

125/130 3334 3129 3200 3258 3278

150

3068 2847 3000 3000 3031

165

2938 2803 2900 3002 2980

180

2798 2756 2800 2872 2799

200

2579 2554 N/A 2688 2680

220

2476

N/A 2500 2602 2415

Table 1: Maximum 30-06 muzzle velocities reported by several reloading manuals for common bullet weights. Hodgdon, Nosler, and Barnes report velocities for 24" barrels. Hornady and Speer report velocoties for 22" barrels. The data are all for barrels with a twist rate of 1 turn in 10" which is needed to stabilize the heaviest bullets. The higher muzzle velocities reported by Nosler for 165 grain and heavier bullets use loads employing a slowburning, double-base powder (Alliant Reloder 22). We have not been able to reproduce these high velocities. Available commercial and peak hand loaded muzzle velocities are also shown in Figure 2.

The ballistics of the 30-06 make it popular target cartridge and an effective hunting round for

1

Ballistics of the 30-06 Rifle Cartridge

everything from groundhogs to deer to elk to bear. (4) With 150-180 grain bullets it typically offers 100 fps more velocity than the .308 Winchester and 200-250 fps less than the .300 Winchester Magnum. In the M1 Garand, the 30-06 is regarded as effective to 440 yards for military use, and the challenge of hitting game animals at longer ranges makes this a sensible maximum hunting range in the hands of most hunters. With care and skill it can be employed at longer ranges in special purpose long-range rifles. Gunnery Sgt. Carlos Hathcock had numerous kills at longer ranges using a Winchester Model 70 chambered in 30-06 while serving in Vietnam. (8) With quality expanding bullets that transfer energy effectively, it provides devastating terminal performance on small to medium sized game including good penetration, large wound channels, and remote wounding effects known as hydrostatic shock. Wide availability of ammunition and rifles, combined with excellent ballistics and terminal performance, make the 30-06 rifle cartridge among the most popular in the world. (9) (10)

bullet was loaded to 2700 fps ("Ball, caliber 30, M1"). Velocity was later reduced to 2640 fps because of difficulties maintaining the pressure specifications at the higher velocity with available powders. A new 152 grain load was introduced in 1940 ("Cartridge Ball, caliber 30, M2") which was widely used in World War II because of good functioning in the M1 Garand rifle. (11)

The maximum pressure allowed by Sporting Arms and Ammunition Manufacturer's Institute (SAAMI) specifications is 60,000 psi or 50,000 cup. With modern powders, many commercial loads are available that provide 2900 fps for 150 grain bullets, 2800 fps for 165 grain bullets, and 2700 fps for 180 grain bullets (in a 24 inch barrel). 125 grain bullets can be pushed to 3150 fps. 220 grain loads typically achieve 2400 fps. Lighter, lower velocity loads are also available to provide reduced recoil.

Figure 3: Drawing showing the dimensions of the 30-06 brass cartridge case (all dimensions in inches). (12)

Figure 2: Maximum muzzle velocities reported by several reloading manuals together with typical velocities reported for commercially available loads in common bullet weights. Some well-known military loads are also shown. Background shows assortment of .308" bullets from 110 grains (left) up through 220 grains (right).

II. Internal Ballistics The 30-06 cartridge case has an internal capacity of 68-69 grains of water. Early military loads propelled a 150 grain bullet at 2700 fps ("Ball Cartridge, caliber 30, Model of 1906"). In 1926, a 172 grain boat tail

Hand loading the 30-06 provides a broader variety of bullet weights and sometimes slightly higher muzzle velocities. Table 1 shows peak muzzle velocities listed by several reloading manuals for various bullet weights. Most 30-06 loads use large rifle or large magnum rifle primers. Both ball (spherical) and cylindrical (extruded) powders are commonly used, as well as single-base (nitrocellulose only) and double-base (nitrocellulose and nitroglycerine) powders. Powders with a wide range of powder burn rates are commonly employed, including powders with burn rates as fast as Reloder 7 and IMR 4198 and as slow as VihtaVuori N165 and Reloder 22. Hodgdon has also published several low-recoil loads

2

Ballistics of the 30-06 Rifle Cartridge

for youth use and target practice using H4198 and 125-135 grain bullets. (13)

According to the Barnes Reloading Manual Number 2, the 30-06 cartridge case capacity of 68.0 grains of water falls between the 7.62x51mm (.308 Winchester) with a capacity of 53.5 grains of water and the .300 Winchester Magnum with a capacity of 90.4 grains of water. (7) Other sources give slightly different case capacities, so case capacities we have measured are shown in Table 2. Case capacity varies slightly by manufacturer and lot number of the brass cartridge case, as well as whether it is determined in new brass or brass that has been fired.

Cartridge

7.62x51mm/ .308

Winchester (grains)

30-06 (grains)

.300 Winchester

Magnum (grains)

Barnes

53.5

Manual

68

90.4

Remington

56.82

69.86

N/A

Brass

Hornady

N/A

70.69

N/A

Brass

Federal

55.51

69.17

N/A

Brass

Lapua

56.25

70.20

N/A

Brass

Nosler

N/A

Brass

N/A

94.6

Table 2: Measured internal cartridge case capacities of fired brass compared with measurements reported in Barnes Reloading Manual Number 2.

Figure 3: A comparison of available muzzle velocities in 7.62x51mm, 30-06, and .300 Winchester Magnum in commonly available bullet weights. Background shows photograph of .308 Winchester (left), 30-06 (middle), and .300 Win Mag (right) rifle cartridges.

III. External Ballistics External ballistics is dominated by a bullet's muzzle velocity and ballistic coefficient, with rifle twist and bullet length also playing a role. This section discusses the issues of twist rates and bullet stability, bullet drop and wind drift, spin drift, and the velocity and kinetic energy retained by a bullet downrange. The broad selection of bullet weights and profiles available for the 30-06 provide a wide range of performance in the area of exterior ballistics.

Figure 3 compares muzzle velocities commonly available in commercial loads for the 7.62x51mm NATO (.308 Winchester), the 30-06, and the .300 Winchester Magnum in typical bullet weights. As with the 30-06, slightly higher (3-5%) muzzle velocities are often available by hand loading. The availability of a military .300 Winchester Magnum load of a 220 grain bullet at 2850 fps is also notable, but this load exceeds the SAAMI peak pressure (62,000 psi) for this cartridge at 68,100 psi. (14)

Figure 4: An assortment of 0.308" diameter bullets available for the 30-06. Left to right: Hornady 110 VMAX, Nosler 125 Ballistic Tip, Hornady 130 SP, Speer 130 FP, Barnes 150 XFP, Speer 150 FP, Hornady 150 RN, Hornady 150 FMJBT, Nosler 150 Ballistic Tip, Nosler 150 E-Tip, Berger 155.5 FBBT, Hornady 165 BTSP, Nosler 165 Ballistic Tip, Nosler 165 Accubond, Barnes 168 TTSX, Speer 200 SP, Nosler 220 Partition SP. Numbers give bullet weight in grains.

3

Ballistics of the 30-06 Rifle Cartridge

1. Rifling Twist Rates and Bullet Stability Just as a football must spin in a spiral to fly point forward rather than tumbling end-over-end, a bullet in flight requires a specific rate of spin to prevent tumbling. This spin is imparted by the barrel's rifling, and the rate of spin required for stability depends on a number of complex factors related to air drag and the bullet's moments of inertia about the axes parallel and perpendicular to its symmetry axis. A bullet's stability in flight is analogous to a spinning top. Just as a top that spins too slowly or not at all will fall over due to the force of gravity a bullet that spins too slowly or not at all will tumble end over end due to the force of air drag.

Conservation of angular momentum gives a bullet a certain amount of gyroscopic stability that makes its axis rigid or resistant to being affected by the overturning aerodynamic torque. Just as a bicycle is easier to balance when the wheels are spinning faster, a bullet spinning faster is harder to upset. A bullet's stability, Sg, is the ratio of the rigidity of the axis of rotation to the magnitude of the overturning aerodynamic torque. (15) More simply stated, stability is the ratio of the tendency to remain point forward to the tendency to tumble in flight. In a perfect world, any stability greater than 1.0 would ensure stable flight. Owing to imperfections in bullet construction, barrel manufacturing, knowledge of atmospheric conditions, and the uncertainty of the formulas, experts recommend selecting a twist rate that provides Sg greater than or equal to 1.4 to ensure stable flight.

Because a bullet's moments of intertia are not

generally known or easily obtainable, a number of

formulas have been offered in attempts to reliably

estimate bullet stability (or required rifling twist rate)

from easily available bullet parameters such as

weight, length, and muzzle velocity. The Greenhill

formula was widely used for many decades, but the

Miller formula for bullet stability has been shown to

be more accurate and widely applicable for

supersonic flight. (16) (17) The Miller formula for

bullet stability is

1

Sg

30m t 2d 3l(1 l 2 )

V

3

2800

(FT 460) (59 460)

29.92 , PT

where m is the mass of the bullet in grains, t is the twist of the barrel in calibers per turn, d is the diameter (caliber) of the bullet in inches, l is the length of the bullet in calibers, V is the muzzle velocity of the bullet in feet per second, FT is the ambient temperature in degrees Fahrenheit, and PT is the air pressure in inches of mercury. The first

30m factor in this complex equation, t 2d 3l(1 l 2 ) , is

simply the uncorrected stability, or the stability at a muzzle velocity of 2800 fps and a standard atmosphere of 59 degrees F and 29.92" of mercury. This part of the formula shows that other factors being equal, stability decreases with bullet length, increases with mass, and that a faster twist rate (smaller t, fewer calibers per turn) increases stability.

1

The second factor in the equation, V 3 , is the 2800

velocity correction factor, describing how stability changes for muzzle velocities other than 2800 fps.

The last factor, (FT 460) 29.92 , is the (59 460) PT

atmospheric correction factor. This factor describes how stability changes with atmospheric density and incorporates effects as temperature deviates from 59 degrees F and pressure 29.92 inches of Hg. The most significant effects here come from the variations in atmospheric pressure with altitude. For example, PT = 24.90" Hg at 5000 ft, and 20.58" Hg at 10,000 ft. (15)[pp. 533-539].

For any given bullet, muzzle velocity, and

atmospheric conditions, stability depends on the

rifling twist rate. Longer bullets require higher twist

rate than shorter bullets. Since the Miller stability

formula is somewhat complicated, the best approach

is to use a spreadsheet or to enter all the parameters

into an available ballistics program, such as the Litz

Point Mass Ballistics Solver (included with the book,

Applied Ballistics of Long Range Shooting) or the

JBM

stability

calculator

(

). A spreadsheet is also available for download at

.

Any of these tools can be used to compute the

stability for a given bullet, barrel twist, and other

conditions.

4

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download