PDF What's the difference betWeen "explosion proof ...
[Pages:1]FAQ
February 19, 2008
What's the difference between
" E x p l o s i o n P r o o f " & " I n t r i n s i c a l ly S a f e "
Electrical equipment sometimes must be installed in areas where combustible vapors and gases are used or may be present. These are commonly referred to as "hazardous locations", and are defined by the National Electrical Code (NEC) in the US, or the Canadian Electrical Code (CEC) in Canada. When equipment must be installed in hazardous locations, there are strict requirements for the construction of the installation, including materials and design requirements. To prevent inadvertent ignition of flammable gases and vapors by electrical equipment, the two most common methods of protection are "Explosion Proof" and "Intrinsically Safe". We will discuss these methods as they relate to gas detection equipment.
Explosion Proof
Generally speaking, "explosion proof" is the more commonly used method for detector/sensor assemblies for fixed gas detection systems, where higher voltages and power requirements may be encountered, and the installation is permanent. Intrinsically safe method can also be used for permanent installations where the detector/sensors are relatively low power devices. Almost all portable instruments use the "intrinsically safe" method.
An "explosion proof " classification for a sensor/transmitter means that the housing has been engineered and constructed to contain a flash or explosion. Such housings are usually made of cast aluminum or stainless steel and are of sufficient mass and strength to safely contain an explosion should flammable gases or vapors penetrate the housing and the internal electronics or wiring cause an ignition. The design must prevent any surface temperatures that could exceed the ignition temperature of the gases or vapors covered by its Group rating (see below). If the sensing element is a high-temperature device (e.g. Catalytic bead or "pellistor"), it may be protected by a flame arrestor to prevent the propagation of high temperature gases to the ambient atmosphere.
Intrinsically Safe
An "intrinsically safe" classification and design means that an electronic circuit and it's wiring will not cause any sparking or arcing and cannot store sufficient energy to ignite a flammable gas or vapor, and cannot produce a surface temperature high enough to cause ignition. Such a design is not explosion proof, nor does it need to be. For permanent installations, such an installation may include "intrinsically safe barriers" that are located outside the hazardous location, and limit the amount of energy available to the device located in the hazardous area.
The North American classifications for hazardous locations as related to flammable gases and vapors:
Class I: Gases and vapors
Division 1: Gases or vapors are usually present and/or may be present at any time in sufficient concentrations for an explosion hazard.
Division 2: Gases or vapors are not normally present and are present only in the event of a leak in some kind of containment vessel or piping, again in potentially hazardous concentrations.
Groups A, B, C, D: Groups of atmospheres categorized by the volatility and/or ignition temperatures. "A" is the most hazardous and "D" is the least hazardous group for gases and vapors.
Group A: Atmospheres containing acetylene.
Group B: Atmospheres containing hydrogen or gases or vapors of equivalent hazard.
Group C: Atmospheres containing ethyl-ether vapors, ethylene, or cyclo-propane.
Group D: Atmospheres containing gasoline, hexane, naptha, benzene, butane, propane, alcohol, acetone, benzol, lacquer solvent vapors, or natural gas (methane).
RKI Instruments, Inc., 33248 Central Ave., Union City, CA 94587 Phone (800) 754-5165 or (510) 441-5656
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- pdf colleagues excellence
- pdf oklahoma children of incarcerated parents toolkit
- pdf git cbt partnership returns new jersey
- pdf advice on non commercial and private gaming and betting
- pdf understanding net positive suction head pump school
- pdf strategic sourcing a step by step practical model adobe
- pdf how can i identify the correct v belt type when the belt is
- pdf intervals between live vaccines and other rules oklahoma
- pdf teacher guide 12 1 gambling home oklahoma state
- pdf lesson 1 idioms from ood everyday english lessons
Related searches
- what s the difference between chose and choose
- what s the difference between your and you re
- what s the difference between anaerobic and aerobic
- what is the difference between influenza a b
- what is the difference between than then
- what is the difference between baking powder
- what is the difference between blood type
- what s the difference between credit and debit
- what s the difference between hispanic and latino
- what s the difference between sign and symptom
- what s the difference between dementia and alzheimer s
- what s the difference between ipad and tablet