“The Fitting People”

[Pages:149]Established 1992

FOR ALL YOUR AIR BRAKE FITTINGS AND ANCILLARY ITEMS

"The Fitting People"

Section

1

Page 1/1 - 1/31

TUV MODULAR AIR BRAKE FITTINGS

Section

2

Page 2/1 - 2/8

FLEETFIT AIR BRAKE FITTINGS

Section

3

Page 3/1 - 3/8

PNEUFIT INDUSTRIAL FITTINGS

Section

4

Page 4/1 - 4/6

PLASTIC & COMPOSITE INDUSTRIAL FITTINGS

Section

5

Page 5/1 - 5/9

PLASTIC INDUSTRIAL FITTINGS

Section

6

Page 6/1 - 6/17

COMPRESSION AIR BRAKE FITTINGS

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

C1

Section

7

Page 7/1 - 7/5

BRASS COMPRESSION FITTINGS

Section

8

Page 8/1 - 8/3

MALLEABLE IRON / STEEL / SEALANTS

Section

9

Page 9/1 - 9/3

BRAKE PIPE FITTINGS & BLEED SCREWS

Section

10

Page 10/1 - 10/3

GREASE NIPPLES & ACCESSORIES

Section

11

Page 11/1 - 11/7

PCL GARAGE / WORKSHOP FITTINGS & ACCESSORIES

Section

12

Page 12/1 - 12/8

COUPLINGS / TEST EQUIP / GAUGES PALMS / FILTERS / VALVES / LOCKS

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

C2

Section

13

Page 13/1 - 13/4

AIR BRAKE COILS & ADAPTORS

Section

14

Page 14/1 - 14/3

ELECTRICAL / ABS / EBS COILS & PLUGS / SOCKETS

Section

15

Page 15/1 - 15/9

AIR BRAKE NYLON TUBING DIN & BS / PVC / RUBBER DIN & BS / HEATER HOSE/ FUEL HOSE / CUPRO NICKEL / CONDUIT / SPIRAL WRAP & ACCESSORIES

Section

16

Page 16/1 - 16/3

AIR RESERVOIRS & ACCESSORIES

Section

17

Page 17/1 - 17/4

REAR MARKER BOARDS / CONSPICUITY TAPE / REFLECTORS

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

C3

Section 1

TUV SIRIT Modular Air Brake Fittings

............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................ ............................................................

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

1 / 1

Scope of use

The SIRIT brass instantaneous push-in fitting has been designed to be used with (Rilsan) 11/12 polyamide or (Hytrel) elastomeric polyester tubings on the pneumatic circuits of auxiliary and braking systems on trucks and trailers.

It is a ready-to-use safety fitting that does not require additional tools or equipment for coupling with the tubing's.

The only operation required is the manual insertion of the tubing in the seat of the fitting.

This makes for a much shorter assembly time than with traditional cutting ring-type couplings.

Assembly time are estimated to be 70%?80% shorter.

The tolerance of the used tubing must comply strictly with those set forth in ISO standard 7628 and DIN standard 74324/73378.

The operating heat range for the SIRIT instantaneous fitting is : +100?C / -40?C.

The seal in these conditions is ensured by means of a specific design mix selected for the SIRIT O-Ring.

The SIRIT fittings for braking systems comply with DIN 2353 regulation. The types of fittings shown in this catalogue are based on the requests made by the main European braking systems installers.

The range which is particularly extensive, is able to satisfy the requirements of truck, trailers and semi-trailers builders as well as those of transformers and spare parts dealers. The working pressures are within the average - low pressure values and correspond to those stated for the light series (L) of DIN 2353. The SIRIT fittings for braking systems can also be used on oil-pressure circuits as long as the pressure does not exceed 250 atm.

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

1 / 2

Assembly Instructions

The seal of the stud coupling is specified by what is laid down in ISO standard 6149-80 and DIN standard 3482. To obtain the correct assembly on all terminal fittings it is essential to adhere to the tightening torques shown in the following table:

Thread

M10 x 1 M12 x 1.5 M14 x 1.5 M16 x 1.5 M18 x 1.5 M22 x1.5 M26 x 1.5

Tightening Torque (Nm) ? 10 22 24 30 35 36 40 45

The tubing must be cut at the right angles with a maximum tolerance of 15?. Correct assembly is performed only when the tubing is inserted touches the end of the tube seat. To be absolutely certain that this is the case it is advisable to mark the depth of the tubing coupling (distance H).

? Pipe (mm) 6 x 4 8 x 6 10 x 7

10 x 7.5 10 x 8 12 x 9 15 x 12 16 x 12 18 x 14

Depth of Coupling (H) 19,8 20,5 24 24 24 25 27 27 27

The tubing/fitting coupling does not require tools. To make the operation easier it is sufficient to slightly turn the tubing. The force required for the fitting is shown in the following table.

? Pipe (mm) M10 x 1 M12 x 1.5 M14 x 1.5 M16 x 1.5 M18 x 1.5 M22 x1.5 M26 x 1.5

Fitting Force (H) 22 24 30 35 36 40 45

Screw the swivel Coupling into the thread ensuring the correct

torque (Over-tightening can cause damage to both the fitting and

the component).

The fit the component by means of push and twist .

IMPORTANT: Check the component is coupled correctly and securely. Pull the component to ensure

The Dimensions shown in the tables in the catalogue are only shown as a guide. We reserve the right to make any due alteration when required for technical reasons.

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

1 / 3

TUV Certificate

TEL: 01474 535456 / FAX: 01474 537323 sales@airbrakeconnections.co.uk

1 / 4

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download