TRIGGER INSTALLATION INSTRUCTIONS - Timney Triggers
Release Date: 7/15/2019
Ruger Precision Rimfire
The World's Finest Triggers
TRIGGER INSTALLATION INSTRUCTIONS
Thank you for purchasing this Timney Trigger. It has been designed and manufactured to provide you with a lifetime of dependable service. Each trigger is hand tested and calibrated on a rifle action before leaving our factory. Please read these instructions fully before you begin installing the trigger, you'll be glad you did.
Installation Instructions
1. Before beginning work on any firearm, remove the ammunition source and double check to ensure the chamber is empty.
2. To install the Ruger Rimfire Precision trigger the following tools are required: -1/8" Allen key. -5/64" Allen-key -Small screwdriver
3. Remove the Chassis Coring Cover. 4. To remove the bolt, press the bolt stop and pull back the bolt simultaneously. 5. Remove the 2 action screws on the bottom with a 1/8" hex key and with the safety selector on safe lift the
barreled-action out of the stock to gain access to the stock trigger. 6. Release the cocking guide spring by depressing the pin and allowing it to move into the long portion of the
"J" shaped slot. 7. Push in the cocking piece guide and slide the factory trigger assembly back and out. 8. Remove the cocking guide, cocking guide spring and plunger and install these components into your new
Timney Ruger Precision Rimfire trigger. 9. Take your new Timney Trigger and make sure the trigger is in the safe position. If the trigger is not in the
safe position the upper receiver will not fit in the lower receiver. Slide the trigger up and in. *If you have a gen.1 model RPR-22 you will need to install the shim that is provided with the trigger between the rear action screw and the trigger mounting hole. Don`t forget to preload the cocking guide piece spring by putting the plunger back into the top of the "J" shaped slot. 10. With the safety selector switch in the "SAFE" position, install the lower receiver back onto the rifle. Next tighten the two bedding screws in the bottom of the stock to torque specs recommended by the manufacturer. 11. Reinstall the bolt and chassis coring cover. 12. The Timney Ruger Precision Rimfire`s pull weight for the first stage (8oz-1lbs) and second stage (1lbs-2lbs) is fully adjustable by adjusting the setscrews as shown below with a 5/64" Allen key. Turn clockwise to increase pull weight and counterclockwise to decrease pull weight. 13. Perform a function check and enjoy your new Timney Trigger.
PHONE ? 623-223-1111 FAX ? 623-223-1112
2020 W QUAIL AVE, PHOENIX AZ. 85027
TECHNICALSUPPORT@
3
4
5
Chassis Coring Cover
Remove bolt
Action Screws
6
7
8
Cocking piece guide
9
9
10
0
Note the safe position
Shim
11
12
12
First stage adjustment
Second stage adjustment
PHONE ? 623-223-1111 FAX ? 623-223-1112
2020 W QUAIL AVE, PHOENIX AZ. 85027
TECHNICALSUPPORT@
NOTE: If you have trouble, contact Timney or check out the troubleshooting steps on the Timney web site. Timney will also install your trigger for $ 40.00 plus $ 35.00 shipping and handling.
TIMNEY TRIGGER GUARANTEE
Material and workmanship: This Timney trigger has been carefully inspected, tested and adjusted to give a lifetime of dependable service. Every possible care has been exercised in its design and construction. If any defect in workmanship or material should develop under conditions of normal use and service, any necessary repairs, including parts and labor will be made at NO CHARGE to the purchaser providing that our inspection reveals parts were not damaged through accident, alteration, misuse, abuse or other causes beyond our control. We neither assume nor imply any oral or statutory warranties, and we neither assume nor authorize any person to assume for us any obligation or liability in connection with this trigger. Repairs or disassembly of this trigger in any manner without specific authorization, voids the guarantee.
PHONE ? 623-223-1111 FAX ? 623-223-1112
2020 W QUAIL AVE, PHOENIX AZ. 85027
TECHNICALSUPPORT@
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- ruger mark ii price guide 22 precision ammo prices
- trigger installation instructions timney triggers
- c39v2 century arms
- glock pistol disassembly assembly
- p365 pistols sig sauer p239
- nra silhouette rifle rulebook
- fastfire 3 user guide layout 1 10 2 15 8 55 am page 1 burris optics
- p i s to l t a r g ets pew pew tactical
- silent captured spring selection guide jp rifles
- making precise windage and using the illuminated reticle leupold