LT1355/LT1356 - Dual and Quad 12MHz, 400V/µs Op Amps - Analog Devices
[Pages:16]FEATURES
n 12MHz Gain Bandwidth n 400V/?s Slew Rate n 1.25mA Maximum Supply Current per Amplifier n Unity-Gain Stable n C-LoadTM Op Amp Drives All Capacitive Loads n 10nV/Hz Input Noise Voltage n 800?V Maximum Input Offset Voltage n 300nA Maximum Input Bias Current n 70nA Maximum Input Offset Current n 12V/mV Minimum DC Gain, RL = 1k n 230ns Settling Time to 0.1%, 10V Step n 280ns Settling Time to 0.01%, 10V Step n ?12V Minimum Output Swing into 500 n ?2.75V Minimum Output Swing into 150 n Specified at ?2.5V, ?5V, and ?15V
APPLICATIONS
n Wideband Amplifiers n Buffers n Active Filters n Data Acquisition Systems n Photodiode Amplifiers
LT1355/LT1356
Dual and Quad 12MHz, 400V/?s Op Amps
DESCRIPTION
The LT?1355/LT1356 are dual and quad low power high speed operational amplifiers with outstanding AC and DC performance. The amplifiers feature much lower supply current and higher slew rate than devices with comparable bandwidth. The circuit topology is a voltage feedback amplifier with matched high impedance inputs and the slewing performance of a current feedback amplifier. The high slew rate and single stage design provide excellent settling characteristics which make the circuit an ideal choice for data acquisition systems. Each output drives a 500 load to ?12V with ?15V supplies and a 150 load to ?2.75V on ?5V supplies. The amplifiers are stable with any capacitive load making them useful in buffer applications.
The LT1355/LT1356 are members of a family of fast, high performance amplifiers using this unique topology and employing Linear Technology Corporation's advanced bipolar complementary processing. For a single amplifier version of the LT1355/LT1356 see the LT1354 data sheet. For higher bandwidth devices with higher supply currents see the LT1357 through LT1365 data sheets. Bandwidths of 25MHz, 50MHz, and 70MHz are available with 2mA, 4mA, and 6mA of supply current per amplifier. Singles, duals, and quads of each amplifier are available.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. C-Load is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
100kHz, 4th Order Butterworth Filter
6.81k 100pF
5.23k 47pF
6.81k VIN
11.3k 330pF
?
1/2 LT1355
+
5.23k
10.2k 1000pF
?
1/2 LT1355
+
VOUT
1355/1356 TA01
AV = ?1 Large-Signal Response
13556 TA01B
13556fc
1
LT1355/LT1356
ABSOLUTE MAXIMUM RATINGS (Note 1)
Total Supply Voltage (V+ to V?)..................................36V Differential Input Voltage (Transient Only) (Note 2).................................................................... ?10V Input Voltage.............................................................. ?VS Output Short-Circuit Duration (Note 3)............. Indefinite Operating Temperature Range (Note 7)
LT1355C/LT1356C/LT1356I..................?40?C to 85?C LT1356H (TC)...................................... ?40?C to 125?C
Specified Temperature Range (Note 8) LT1355C/LT1356C.................................... 0?C to 70?C LT1356I.................................................?40?C to 85?C LT1356H (TC)...................................... ?40?C to 125?C
Maximum Junction Temperature .......................... 150?C Storage Temperature Range...................? 65?C to 150?C Lead Temperature (Soldering, 10 sec).................... 300?C
PIN CONFIGURATION
LT1355
OUT A 1 ?IN A 2 +IN A 3
V? 4
TOP VIEW
A B
8 V+ 7 OUT B 6 ?IN B 5 +IN B
LT1356
N8 PACKAGE 8-LEAD PDIP
TJMAX = 150?C, JA = 130?C/W
TOP VIEW
OUT A 1
?IN A 2 A
+IN A 3 V+ 4
+IN B 5 B
?IN B 6
OUT B 7
14 OUT D
13 ?IN D D
12 +IN D 11 V?
10 +IN C C
9 ?IN C
8 OUT C
N PACKAGE 14-LEAD PDIP
TJMAX = 150?C, JA = 110?C/W
LT1355 LT1356
OUT A 1 ?IN A 2 +IN A 3
V? 4
TOP VIEW
A B
8 V+ 7 OUT B 6 ?IN B 5 +IN B
S8 PACKAGE 8-LEAD PLASTIC SO
TJMAX = 150?C, JA = 190?C/W
OUT A 1 ?IN A 2 +IN A 3
V+ 4 +IN B 5 ?IN B 6 OUT B 7
NC 8
TOP VIEW
16 OUT D
15 ?IN D
A
D
14 +IN D
13 V?
12 +IN C
B
C
11 ?IN C
10 OUT C
9 NC
S PACKAGE 16-LEAD PLASTIC SO
TJMAX = 150?C, JA = 150?C/W, JC = 30?C/W
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING
PACKAGE DESCRIPTION
LT1355CN8#PBF
LT1355CN8#TRPBF
LT1355CN8
8-Lead PDIP
LT1355CS8#PBF
LT1355CS8#TRPBF
1355
8-Lead Plastic SO
LT1356CN#PBF
LT1356CN#TRPBF
LT1356CN
14-Lead PDIP
LT1356CS#PBF
LT1356CS#TRPBF
LT1356CS
16-Lead Plastic SO
LT1356IS#PBF
LT1356IS#TRPBF
LT1356S
16-Lead Plastic SO
LT1356HS#PBF
LT1356HS#TRPBF
LT1356S
16-Lead Plastic SO
Consult LTC Marketing for parts specified with wider operating temperature ranges. Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: For more information on tape and reel specifications, go to:
2
SPECIFIED TEMPERATURE RANGE 0?C to 70?C 0?C to 70?C 0?C to 70?C 0?C to 70?C ?40?C to 85?C ?40?C < TC < 125?C
13556fc
LT1355/LT1356
ELECTRICAL CHARACTERISTICS TA = 25?C, VCM = 0V unless otherwise noted.
SYMBOL PARAMETER
VOS
Input Offset Voltage
IOS
Input Offset Current
IB
Input Bias Current
en
Input Noise Voltage
in
Input Noise Current
RIN
Input Resistance
Input Resistance
CIN
Input Capacitance
Input Voltage Range+
Input Voltage Range?
CONDITIONS
f = 10kHz f = 10kHz VCM = ?12V Differential
CMRR Common Mode Rejection Ratio
PSRR AVOL
Power Supply Rejection Ratio Large-Signal Voltage Gain
VOUT
Output Swing
IOUT
Output Current
ISC
Short-Circuit Current
SR
Slew Rate
Full-Power Bandwidth
GBW
Gain Bandwidth
tr, tf
Rise Time, Fall Time
Overshoot
Propagation Delay
ts
Settling Time
VCM = ?12V VCM = ?2.5V VCM = ?0.5V VS = ?2.5V to ?15V VOUT = ?12V, RL = 1k VOUT = ?10V, RL = 500 VOUT = ?2.5V, RL = 1k VOUT = ?2.5V, RL = 500 VOUT = ?2.5V, RL = 150 VOUT = ?1V, RL = 500 RL = 1k, VIN = ?40mV RL = 500, VIN = ?40mV RL = 500, VIN = ?40mV RL = 150, VIN = ?40mV RL = 500, VIN = ?40mV VOUT = ?12.0V VOUT = ?2.75V VOUT = 0V, VIN = ?3V AV = ?2 (Note 4)
10V Peak (Note 5) 3V Peak (Note 5) f = 200kHz, RL = 2k
AV = 1, 10% to 90%, 0.1V
AV = 1, 0.1V
50% VIN to 50% VOUT, 0.1V
10V Step, 0.1%, AV = ?1 10V Step, 0.01%, AV = ?1 5V Step, 0.1%, AV = ?1 5V Step, 0.01%, AV = ?1
VSUPPLY
MIN
?15V ?5V ?2.5V
?2.5V to ?15V
?2.5V to ?15V
?2.5V to ?15V
?2.5V to ?15V
?15V
70
?15V
?15V
?15V
12.0
?5V
2.5
?2.5V
0.5
?15V ?5V ?2.5V
?15V
83
?5V
78
?2.5V
68
92
?15V
12
?15V
5
?5V
12
?5V
5
?5V
1
?2.5V
5
?15V
13.3
?15V
12.0
?5V
3.5
?5V
2.75
?2.5V
1.3
?15V
24.0
?5V
18.3
?15V
30
?15V
200
?5V
70
?15V ?5V
?15V
9.0
?5V
7.5
?2.5V
?15V ?5V
?15V ?5V
?15V ?5V
?15V ?15V ?5V ?5V
TYP
0.3 0.3 0.4
20
80
10
0.6
160
11
3
13.4 3.5 1.1
?13.2 ?3.4 ?0.9
97 84 75
106
36 15 36 15 4 20
13.8 13.0 4.0 3.3 1.7
30 25
42
400 120
6.4 6.4
12.0 10.5 9.0
14 17
20 18
16 19
230 280 240 380
MAX 0.8 0.8 1.0 70 300
?12.0 ?2.5 ?0.5
UNITS
mV mV mV
nA
nA
nV/Hz
pA/Hz
M
M
pF
V V V
V V V
dB dB dB
dB
V/mV V/mV V/mV V/mV V/mV V/mV
?V ?V ?V ?V ?V
mA mA
mA
V/?s V/?s
MHz MHz
MHz MHz MHz
ns ns
% %
ns ns
ns ns ns ns
13556fc
3
LT1355/LT1356
ELECTRICAL CHARACTERISTICS TA = 25?C, VCM = 0V unless otherwise noted.
SYMBOL PARAMETER Differential Gain
CONDITIONS f = 3.58MHz, AV = 2, RL = 1k
VSUPPLY
?15V ?5V
MIN TYP MAX
2.2 2.1
Differential Phase
f = 3.58MHz, AV = 2, RL = 1k
?15V
3.1
?5V
3.1
RO
Output Resistance
Channel Separation
IS
Supply Current
AV = 1, f = 100kHz
VOUT = ?10V, RL = 500
Each Amplifier Each Amplifier
?15V
?15V
?15V ?5V
0.7
100
113
1.0
1.25
0.9
1.20
UNITS
% %
Deg Deg
dB
mA mA
The l denotes the specifications which apply over the temperature range 0?C TA 70?C, VCM = 0V, unless otherwise noted.
SYMBOL PARAMETER
VOS
Input Offset Voltage
CONDITIONS
VSUPPLY
?15V ? 5V ?2.5V
MIN TYP MAX
l
1.0
l
1.0
l
1.2
IOS IB CMRR
Input VOS Drift Input Offset Current Input Bias Current Common Mode Rejection Ratio
PSRR AVOL
Power Supply Rejection Ratio Large-Signal Voltage Gain
VOUT
Output Swing
IOUT
Output Current
ISC
Short-Circuit Current
SR
Slew Rate
(Note 6)
VCM = ?12V VCM = ?2.5V VCM = ?0.5V VS = ?2.5V to ?15V VOUT = ?12V, RL = 1k VOUT = ?10V, RL = 500 VOUT = ?2.5V, RL = 1k VOUT = ?2.5V, RL = 500 VOUT = ?2.5V, RL = 150 VOUT = ?1V, RL = 500 RL = 1k, VIN = ?40mV RL = 500, VIN = ?40mV RL = 500, VIN = ?40mV RL = 150, VIN = ?40mV RL = 500, VIN = ?40mV VOUT = ?11.5V VOUT = ?2.5V VOUT = 0V, VIN = ?3V AV = ? 2, (Note 4)
?2.5V to ?15V l
5
8
?2.5V to ?15V l
100
?2.5V to ?15V l
450
?15V ?5V ?2.5V
l 81 l 77 l 67
l 90
?15V ?15V ?5V ?5V ?5V ?2.5V
l 10.0 l 3.3 l 10.0 l 3.3 l 0.6 l 3.3
?15V ?15V ? 5V ?5V ?2.5V
l 13.2 l 11.5 l 3.4 l 2.5 l 1.2
?15V
l 23.0
?5V
l 16.7
?15V
l 24
?15V ?5V
l 150 l 60
GBW
Gain Bandwidth
f = 200kHz, RL = 2k
?15V
l 7.5
?5V
l 6.0
Channel Separation
IS
Supply Current
VOUT = ?10V, RL = 500
?15V
l 98
Each Amplifier Each Amplifier
?15V
l
1.45
?5V
l
1.40
UNITS
mV mV mV
?V/?C
nA
nA
dB dB dB
dB
V/mV V/mV V/mV V/mV V/mV V/mV
?V ?V ?V ?V ?V
mA mA
mA
V/?s V/?s
MHz MHz
dB
mA mA
13556fc
4
LT1355/LT1356
ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the ?40?C TA 85?C
and ?40?C TC 125?C temperature ranges, VCM = 0V unless otherwise noted. (Note 8)
SYMBOL PARAMETER
VOS
Input Offset Voltage
CONDITIONS
VSUPPLY
?15V ?5V ?2.5V
MIN TYP MAX
l
1.8
l
1.8
l
2.0
UNITS
mV mV mV
IOS IB CMRR
Input Offset Current Input Bias Current Common Mode Rejection Ratio
PSRR AVOL
Power Supply Rejection Ratio Large-Signal Voltage Gain
VOUT
Output Swing
IOUT
Output Current
ISC
Short-Circuit Current
SR
Slew Rate
VCM = ?12V VCM = ?2.5V VCM = ?0.5V VS = ?2.5V to ?15V VOUT = ?12V, RL = 1k VOUT = ?2.5V, RL = 1k VOUT = ?2.5V, RL = 500 VOUT = ?1V, RL = 500 RL = 1k, VIN = ?40mV RL = 500, VIN = ?40mV RL = 500, VIN = ?40mV VOUT = ?12.7V VOUT = ?3.3V VOUT = 0V, VIN = ?3V AV = ?2, (Note 4)
?2.5V to ?15V l
?2.5V to ?15V l
?15V ?5V ?2.5V
l 80 l 76 l 66
l 90
?15V ?5V ?5V ?2.5V
l 6.0 l 4.0 l 1.7 l 1.7
?15V ?5V ?2.5V
l 12.7 l 3.3 l 1.2
?15V ?5V
l 12.7 l 6.6
?15V
l 16
?15V ?5V
l 110 l 43
250
nA
600
nA
dB dB dB
dB
V/mV V/mV V/mV V/mV
?V ?V ?V
mA mA
mA
V/?s V/?s
GBW
Gain Bandwidth
f = 200kHz, RL = 2k
?15V
l 6.0
MHz
?5V
l 4.6
MHz
Channel Separation
IS
Supply Current
VOUT = ?10V, RL = 500
Each Amplifier Each Amplifier
?15V
?15V ?5V
l 96 l l
dB
1.55
mA
1.50
mA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.
Note 2: Differential inputs of ?10V are appropriate for transient operation only, such as during slewing. Large, sustained differential inputs will cause excessive power dissipation and may damage the part. See Input Considerations in the Applications Information section of this data sheet for more details.
Note 3: A heat sink may be required to keep the junction temperature below absolute maximum when the output is shorted indefinitely.
Note 4: Slew rate is measured between ?10V on the output with ?6V input for ?15V supplies and ?1V on the output with ?1.75V input for ?5V supplies.
Note 5: Full power bandwidth is calculated from the slew rate measurement: FPBW = (SR)/2VP.
Note 6: This parameter is not 100% tested.
Note 7: The LT1355C/LT1356C/LT1356I are guaranteed functional over the operating temperature range of ?40?C to 85?C. The LT1356H is guaranteed functional over the operating temperature range of ?40?C to 125?C case temperature (TC).
Note 8: The LT1355C/LT1356C are guaranteed to meet specified performance from 0?C to 70?C. The LT1355C/LT1356C are designed, characterized and expected to meet specified performance from ?40?C to 85?C, but are not tested or QA sampled at these temperatures. The LT1356I is guaranteed to meet specified performance from ?40?C to 85?C. The LT1356H is guaranteed to meet specified performance from ?40?C to 125?C case temperature (TC). The parts are pulse tested at these temperatures. Internal warm-up drift must be taken into account separately. Care must be taken not to exceed the maximum junction temperature.
13556fc
5
LT1355/LT1356 TYPICAL PERFORMANCE CHARACTERISTICS
Supply Current vs Supply Voltage and Temperature
1.4
1.2 125?C
1.0
25?C
Input Common Mode Range
vs Supply Voltage
V+
?0.5
TA = 25?C VOS < 1mV
?1.0
?1.5
?2.0
Input Bias Current vs Input Common Mode Voltage
200
VS = ?15V
150
TA = IB =
25?C --IB--+ +--IB--?
2
100
INPUT BIAS CURRENT (nA)
COMMON MODE RANGE (V)
SUPPLY CURRENT (mA)
0.8 0.6 0.4
0
?55?C
5
10
15
20
SUPPLY VOLTAGE (?V)
1355/1356 G01
2.0 1.5 1.0 0.5 V?
0
5
10
15
20
SUPPLY VOLTAGE (?V)
1355/1356 G02
50
0
?50 ?15 ?10 ?5 0
5 10 15
INPUT COMMON MODE VOLTAGE (V)
1355/1356 G03
INPUT BIAS CURRENT (nA)
Input Bias Current vs Temperature
200
175
150
VS = IB =
?15V --IB--+ +--IB--?
2
125
100
75
50
25
0 ?50 ?25
0 25 50 75 TEMPERATURE (?C)
100 125
1355/1356 G04
INPUT VOLTAGE NOISE (nV/Hz)
Input Noise Spectral Density
100
10
VS = ?15V
TA = 25?C
AV = 101
RS = 100k
in
en
10
1
1
0.1
10
100
1k
10k
100k
FREQUENCY (Hz)
1355/1356 G05
INPUT CURRENT NOISE (pA/Hz)
OPEN-LOOP GAIN (dB)
Open-Loop Gain
vs Resistive Load
100 TA = 25?C
VS = ?15V
90
VS = ?5V
80
70 60
50 10
100
1k
10k
LOAD RESISTANCE ()
1355/1356 G06
OPEN-LOOP GAIN (dB)
Open-Loop Gain vs Temperature
97 VS = ?15V
96 RL = 1k VO = ?12V
95
94
93
92
91
90
89
88 ?50 ?25
0 25 50 75 100 125 TEMPERATURE (?C)
1355/1356 G07
6
OUTPUT VOLTAGE SWING (V)
Output Voltage Swing
vs Supply Voltage
V+ TA = 25?C
?1
RL = 1k
?2 RL = 500
?3
3 RL = 500
2
1 V?
0
RL = 1k
5
10
15
20
SUPPLY VOLTAGE (?V)
1355/1356 G08
Output Voltage Swing
vs Load Current
V+?0.5 ?1.0
VS = ?5V VIN = 100mV
85?C
?1.5
?40?C
?2.0
?2.5
25?C
OUTPUT VOLTAGE SWING (V)
85?C 2.5
2.0
25?C
?40?C 1.5
1.0 V? + 0.5
?50 ?40 ?30 ?20 ?10 0 10 20 30 40 50 OUTPUT CURRENT (mA)
1355/1356 G09
13556fc
TYPICAL PERFORMANCE CHARACTERISTICS
LT1355/LT1356
OUTPUT SHORT-CIRCUIT CURRENT (mA)
OUTPUT IMPEDANCE ()
Output Short-Circuit Current vs Temperature
65 VS = ?5V
60
55
50
45 SINK
40 SOURCE
35
30
25
20 ?50 ?25
0 25 50 75 100 125 TEMPERATURE (?C)
1355/1356 G10
OUTPUT SWING (V)
Settling Time vs Output Step (Noninverting)
10 VS = ?15V
8 AV = 1
6
4
10mV
1mV
2
0
?2
?4
10mV
1mV
?6
?8
?10 50
100 150 200 250 300 350 SETTLING TIME (ns)
1355/1356 G11
OUTPUT SWING (V)
Settling Time vs Output Step (Inverting)
10 VS = ?15V
8 AV = ?1
6
4
10mV
2
1mV
0
?2 1mV
?4
?6
10mV
?8
?10 50
100 150 200 250 300 350 SETTLING TIME (ns)
1355/1356 G12
PHASE MARGIN (DEG) PHASE MARGIN (DEG)
Output Impedance vs Frequency
1k 100 AV = 100
VS = ?15V TA = 25?C
10
AV = 10 1
AV = 1
0.1
0.01 10k
100k
1M
10M
FREQUENCY (Hz)
100M
1355/1356 G13
VOLTAGE MAGNITUDE (dB)
Frequency Response vs Capacitive Load
10 VS = ?15V
8 TA = 25?C 6 AV = ?1
C = 1000pF
4
C = 500pF
2
C = 100pF
0
C = 50pF
?2
?4
C = 0
?6
?8
?10 100k
1M
10M
FREQUENCY (Hz)
100M
1355/1356 G19
GAIN BANDWIDTH (MHz)
Gain Bandwidth and Phase
Margin vs Supply Voltage
18 TA = 25?C
17 16
50
48 PHASE MARGIN
46
15
44
14
42
13
40
12
38
11
GAIN BANDWIDTH
36
10
34
9
32
8
30
0
5
10
15
20
SUPPLY VOLTAGE (?V)
1355/1356 G15
Gain Bandwidth and Phase Margin vs Temperature
18
52
PHASE MARGIN
17
VS = ?15V
50
16
PHASE MARGIN 48
15
VS = ?5V
46
14
44
13
GAIN BANDWIDTH 42
12
VS = ?15V
40
11
38
10 GAIN BANDWIDTH
36
9 VS = ?5V
34
8 ?50 ?25
32 0 25 50 75 100 125 TEMPERATURE (?C)
1355/1356 G16
GAIN (dB) GAIN (dB)
Frequency Response vs Supply Voltage (AV = 1)
5 TA = 25?C
4 AV = 1 3 RL = 2k
2
1
?15V
0
?1
?2
?5V
?3 ?2.5V
?4
?5 100k
1M
10M
FREQUENCY (Hz)
100M
1355/1356 G17
Frequency Response vs Supply Voltage (AV = ?1)
5 TA = 25?C
4 AV = ?1 3 RF = RG = 2k
2
1
0
?1
?2
?5V
?3 ?4 ?5
100k
?2.5V ?15V
1M
10M
FREQUENCY (Hz)
100M
1355/1356 G18
13556fc
7
GAIN BANDWIDTH (MHz)
LT1355/LT1356 TYPICAL PERFORMANCE CHARACTERISTICS
GAIN (dB)
SLEW RATE (V/?s)
Gain and Phase vs Frequency
70
120
60
PHASE
100
50
VS = ?15V 80
VS = ?15V
40
60
GAIN 30
VS = ?5V
40
20
VS = ?5V
20
10
TA = 25?C 0 AV = ?1
RF = RG = 2k
?10
10k
100k
1M
10M
FREQUENCY (Hz)
0 100M
1355/1356 G14
Slew Rate vs Supply Voltage
600
TA = 25?C
AV = ?1
500
RF SR
= =
RSGR=+2+k SR? ----------
400
2
300
200
100
PHASE (DEG)
SLEW RATE (V/?s)
COMMON MODE REJECTION RATIO (dB)
POWER SUPPLY REJECTION RATIO (dB)
Power Supply Rejection Ratio vs Frequency
100
80
+PSRR
VS = ?15V TA = 25?C
?PSRR 60
40
20
Common Mode Rejection Ratio vs Frequency
120 VS = ?15V TA = 25?C
100
80
60
40
20
0 100 1k 10k 100k 1M 10M 100M
FREQUENCY (Hz)
1355/1356 G20
0
1k
10k 100k 1M 10M 100M
FREQUENCY (Hz)
1355/1356 G21
Slew Rate vs Temperature
350
300
250
200
AV SR
= =
?2 --S--R+--+ --SR--?
2
150
VS = ?15V
Slew Rate vs Input Level
500
TA = 25?C
VS = ?15V
400 AV = ?1
RF SR
== R--SGR--=+--2+kS--R--?
300
2
200
SLEW RATE (V/?s)
100
VS = ?5V
100
0
0
5
10
15
SUPPLY VOLTAGE (?V)
1355/1356 G22
Total Harmonic Distortion vs Frequency
0.1 TA = 25?C VO = 3VRMS RL = 2k
0.01
0.001 0.0001
10
AV = ?1 AV = 1
100
1k
10k
100k
FREQUENCY (Hz)
1355/1356 G25
OUTPUT VOLTAGE (VP-P)
50 ?50 ?25
0 25 50 75 100 125 TEMPERATURE (?C)
1355/1356 G23
Undistorted Output Swing vs Frequency (? 15V)
30
AV = ?1 25
20 AV = 1
15
10
VS = ?15V RL = 5k
AV = 1,
5 1% MAX DISTORTION
AV = ?1,
4% MAX DISTORTION
0
100k
1M
FREQUENCY (Hz)
10M
1355/1356 G26
OUTPUT VOLTAGE (VP-P)
0 0 2 4 6 8 10 12 14 16 18 20 INPUT LEVEL (VP-P)
1355/1356 G24
Undistorted Output Swing vs Frequency (? 5V)
10
8
AV = ?1
AV = 1 6
4
VS = ?5V
RL = 5k
2
AV = 1, 2% MAX DISTORTION
AV = ?1,
3% MAX DISTORTION
0
100k
1M
FREQUENCY (Hz)
10M
1355/1356 G27
TOTAL HARMONIC DISTORTION (%)
13556fc
8
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- th st congress session h r 1356
- draft statewide rail plan
- geometric inconsistencies and accident experience on two lane rural
- safety effects of geometric improvements on horizontal curves
- roadway design standards to accommodate low clearance vehicles
- house bill 22 1356 by representative s herod and hooton colorado
- th st congress session s 1356
- summary of us dot national crossing inventory requirements for the rail
- administration for children and families 45 cfr part 1356 hhs
- sb 1356 arizona state legislature
Related searches
- tracking devices for tools and equipment
- securities and exchange commissions filing s page
- ed devices and aids
- volt amps to amps calculator
- upper case and lower case abc s printables
- ace and arb dual therapy
- electronic devices and circuits
- electronic devices and circuit theory pdf
- electronic devices and circuits book
- electronics devices and circuits pdf
- pros and cons of trump s presidency
- 400v dc power supply