Mold Spec Guidelines
Mold SpecGuidelinesTable of Contents Page # Introduction2 Considerations2 Mold Classification Guidelines 3Mold Buyers Specification Checklist3-4Material Standards5Hot Runner and Valve Gate Systems5Electrical Systems6Hydraulic Core Pull Systems6Automation6Mold Safety Guidelines6Mold Numbering7Date Code7Alignment7Cycle Counting7Cavity ID Numbering8Steel Treating and Lubrication8Documentation9Mold Shipping9Mold Approval10Approved Mold Component and Material Suppliers11Addendum ‘A’: Mold Classification Description12-24A)IntroductionThese Mold Spec Guidelines have been developed to meet or exceed customer expectations, and the demands that will be upon the tool.These guidelines will further evolve, therefore communication between mold builder and mold buying Tooling Engineer is essential.B)ConsiderationsUnderstand and incorporate customer requirementsMatch the mold to the overall project requirementsDetermine the optimal mold designStandardize wherever possibleMold Classification GuidelinesOverview:These different classifications will dictate differences in design, construction, materials, and components of molds. Any deviations must be communicated to the Tooling Engineer prior to mold construction, in writing. Class 1: Extremely High VolumeExtremely high volume production injection molds built for lifetime cycles exceeding one million.Class 2: High VolumeMedium to high volume production injection molds built for lifetime cycles not to exceed one million.Class 3: Medium VolumeMedium volume production injection molds built for lifetime cycles not to exceed 500,000.Class 4: Low VolumeLow volume production injection molds built for lifetime cycles not to exceed 100,000.Class 5: Prototype OnlyPrototype only molds are built for lifetime cycles not to exceed 5,000. Mold Classification CategoryExtremely High VolumeHigh VolumeMedium VolumeLow VolumePrototype OnlyTotal Runnerless Design (If Part Allows)XStainless Steel or Electroless Nickel Plated Mold BaseXSpare Parts for ToolingXXStainless Steel or Electroless Nickel Plated Water PlatesXXAutomatic Molding Cycles & Part De-gatingXXXFull Detailed Mold DesignXXXHeat Treated Cavity & Core InsertsXXXAlignment LocksXXXGuided EjectionXXXWear Plates on all SlidesXXXAutomatic Side ActionsXXXSpring Loaded or Mechanically Operated KO SystemXXXXCycle CounterXXXXPre-Hardened Cavity & Core InsertsXXAluminum Cavity & Core Inserts or Aluminum MoldXD)Mold Buyers Specification ChecklistWhen issuing a RFQ, the specification check list on the following page is to be supplied. Mold Buyers Specification ChecklistTo: FORMTEXT _________________________????RFQ Number FORMTEXT ?????_____From: FORMTEXT ????? Date: FORMTEXT ?????Customer Name: FORMTEXT ?????CAD filename: FORMTEXT ?????Part Name: FORMTEXT ?????Part Number: FORMTEXT ?????Resin Type: FORMTEXT ?????Shrinkage: FORMTEXT ????? FORMCHECKBOX Uniform / FORMCHECKBOX SpecifiedMold Base Size: FORMTEXT ?????Number of Cavities: FORMTEXT ?????Press Tonnage: FORMTEXT ?????Press Brand: FORMTEXT ?????Mold Type: FORMCHECKBOX 2 Plate FORMCHECKBOX 3 Plate FORMCHECKBOX Vertical FORMCHECKBOX Unscrewing FORMCHECKBOX Insert (Pick-Outs) FORMCHECKBOX Other: FORMCHECKBOX Stack FORMCHECKBOX Quick Change Insert FORMCHECKBOX Collapsible Core/Expandable Cavity FORMCHECKBOX ShuttleGate Type:Runner Type:Cavity Finish:Core Finish: FORMCHECKBOX Pin FORMCHECKBOX Cold FORMCHECKBOX SPI/SPE# FORMCHECKBOX SPI/SPE# FORMCHECKBOX Tunnel FORMCHECKBOX Hot Runner System FORMCHECKBOX EDM FORMCHECKBOX EDM FORMCHECKBOX Edge FORMCHECKBOX Hot Sprue Bushing FORMCHECKBOX Texture/Plating FORMCHECKBOX Texture/Plating FORMCHECKBOX Direct Sprue FORMCHECKBOX Hot Drops FORMCHECKBOX Describe: FORMTEXT ????? FORMCHECKBOX Describe: FORMTEXT ????? FORMCHECKBOX Hot Runner Valve FORMCHECKBOX Other: FORMTEXT ????? FORMCHECKBOX Hot Runner Hot Tip FORMCHECKBOX Supplier: FORMTEXT ?????________ FORMCHECKBOX Other: FORMTEXT ?????Ejection:“A” Side “B” SideSide ActionsComponent Standards Miscellaneous:Pin FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Angle Pin FORMCHECKBOX Inch FORMCHECKBOX Date Code InsertBlade FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Hydraulic FORMCHECKBOX JIS FORMCHECKBOX Pressure TransducerStripper-plate/Ring FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Pneumatic FORMCHECKBOX DIN FORMCHECKBOX Customer Logo (Molded)Lift FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Electric FORMCHECKBOX Supplier: ___________ FORMCHECKBOX Customer Mold IDDouble Stage FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Other: FORMTEXT ????? FORMCHECKBOX Mold builder Info on MoldAir FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Early Return Ejector SystemDelayed FORMCHECKBOX FORMCHECKBOX Alignment FORMCHECKBOX Cycle CounterManual FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Straight Locks FORMCHECKBOX Cycle MonitorSleeves FORMCHECKBOX FORMCHECKBOX FORMCHECKBOX Taper Locks FORMCHECKBOX Other: __________Mold Classification: Refer to Mold Buyers Specification for details FORMCHECKBOX Extremely High VolumeCavity & Core Steel: FORMCHECKBOX Stainless Steel FORMCHECKBOX Hardened Tool Steel FORMCHECKBOX High VolumeCavity & Core Steel: FORMCHECKBOX Stainless Steel FORMCHECKBOX Hardened Tool SteelAssociated Inserts: FORMCHECKBOX Stainless Steel FORMCHECKBOX Hardened Tool Steel FORMCHECKBOX Inserted Cavity & Cores FORMCHECKBOX Inserted Runner Plate FORMCHECKBOX Alignment Locks FORMCHECKBOX Guided Ejector System FORMCHECKBOX Side Action Wear Plate FORMCHECKBOX Plate Water Lines FORMCHECKBOX Mold Temperature will exceed 250 deg F. FORMCHECKBOX Other: Describe: FORMCHECKBOX Medium VolumeCavity & Core Steel: FORMCHECKBOX Stainless Steel FORMCHECKBOX Hardened Tool SteelAssociated Inserts: FORMCHECKBOX Stainless Steel FORMCHECKBOX Hardened Tool Steel FORMCHECKBOX Inserted Cavity & Cores FORMCHECKBOX Inserted Runner Plate FORMCHECKBOX Alignment Locks FORMCHECKBOX Guided Ejector System FORMCHECKBOX Side Action Wear Plate FORMCHECKBOX Plate Water Lines FORMCHECKBOX Mold Temperature will exceed 250 deg F. FORMCHECKBOX Other: Describe: FORMTEXT ????? FORMCHECKBOX Low VolumeAlignment LocksOther: Describe: FORMTEXT ????? FORMCHECKBOX Prototype Other: Describe: FORMTEXT ????? FORMCHECKBOX Mold Build Standards and Component Usage, to be in accordance with current Mold Designer Specification Book.E)Material StandardsProduction tooling shall be constructed using standard materials. Use quality named sources for mold steels and mold components. Quality mold steel suppliers will provide steel certifications per request; keep all steel certifications on file. Utilize standard Lift Actions, Side Actions and Mold Components wherever possible. Exceptions must be approved by the Tooling Engineer in writing. See “R) Approved Supplier Standards”. F)Hot Runner and Valve Gate SystemsAll hot runner or valve gate hot runner molds shall be designed using preferred systems specified by Tooling Engineer. The type/design of the hot runner or valve gate system will be determined by the part/mold design. Use of non-preferred hot runner or valve gate systems must be approved in writing by Tooling Engineer and Engineering Manager.Considerations when selecting the hot runner or valve gate system should be:Standardization with existing systems wherever possibleUniform plastic material heating throughout system Ease of maintenance and disassemble/assemblySpares parts and service availabilityHot runner and valve gate control system compatibility and availabilityIndividual part cavity filling, cavity sealing, and gate aesthetics Standardization and ease of wiringStandardization of electrical connectionsWiring and components compatible with local power requirements.All electrical connectors in junction box shall be XXXX pin connectors or Equivalent. Both power and thermocouple connectors are ‘male’ type on the mold junction box and are ‘female’ type on the temperature controller cables. Heater and thermocouple wires shall not be exposed and shall be secured in wire channels. Prefer wire channels to be in the cavity-side face of the hot runner plate assembly wherever possible. All wires should be easily accessible and not threaded through the mold wherever possible.All heater and thermocouple junction boxes shall be securely mounted to the “top” half of the mold wherever possible. The hot runner manifold shall have a 4 inch diameter locating ring and a 1/2 inch spherical radius sprue bushing unless otherwise noted by Tooling Engineer.All hot runner or valve gate molds shall have Manifold and Cavity Zone Layout engraved on operator side of mold or identified on a plate attached to operator side of mold.All hot runner or valve gate systems molds shall have an insulation plate securely attached to front face of mold.Prefer manifolds to have leader pins for ease of assemble wherever possible. G)Electrical SystemsAll heater and thermocouple junction boxes shall be securely mounted on the “top” of mold wherever possible. The junction box shall have a removable front panel to allow wiring access without disturbing the connectors wherever possible. All wiring shall be connected into terminal strips inside the junction box, with short runs to connectors wherever possible. All connections to the mold hot runner systems shall be made using standard type connectors. All connections shall be routed and installed into single connection plate box wherever possible. All mold designs shall contain a detailed electrical connection diagram.H)Hydraulic Core Pull Systems All molds with core pull and unscrewing mechanisms shall conform to the following guidelines unless otherwise noted by the Tooling Engineer: Hydraulic motors shall be specified by the Tooling Engineer. Motors shall be marked to identify “in” and “out” rotation ports except where an approved rack drive unscrewing is used. Preferred hydraulic cylinders shall be 3000 PSI with proximity switches as required. Hydraulic cylinders shall be Parker, Miller Brand or equivalent. All core pull or unscrewing molds shall have the mold mechanism sequence clearly stamped on operator side of mold. All unscrewing cores shall be of H-13 or 440 Stainless Steel materials and shall be heat treated to 52 Rockwell “C” hardness. For maximum wear also Nitride H-13 .005 / .007” Deep / side. All unscrewing molds shall be designed with a standard replaceable bushing housing on all unscrewing core details wherever possible to prevent wear to unwinding cores.I)Automation All Class 1: Extremely High Volume, Class 2: High Volume and Class 3: Medium Volume production molds must run fully automatic molding cycles. Full automatic molding cycles can be accomplished by automatic ejection of parts that free-fall to conveyer or by removal of parts from mold using robot. All Class 1, Class 2 and Class 3 molds shall be designed to best accommodate the selected method of automated part removal from the mold.J)Mold Safety GuidelinesConsideration should be given at the mold design stage to reduce potential safety issues for tool room and molding room personnel.Break sharp corners and edges wherever possible.Guard pinch points such as in unscrewing mold cylinder structures.Locate eyebolt holes in large plates and large inserts.Provide a lift hole at the center of the mold’s gravity.Provide a mold strap to prevent unintended opening of the tool.All eyebolt holes should be inch standard. Stamp MM next to any metric eyebolt holes.K)Mold Numbering The designated mold number shall be supplied by Tooling Engineer. All Class 1: Extremely High Volume, Class 2: High Volume, Class 3: Medium Volume and Class 4: Low Volume production molds shall be identified with the following information engraved/stamped onto side or top of mold or by an identification plate attached to the side or top of mold:CorporationPart Number, (s)Mold Number Number of Mold CavitiesMold Manufacturer NameMold Manufacture DateMold Weight, (pounds) L)Date Code All Part Numbering and Date Code identification in mold cavities shall be according to the approved Part Drawing when available.Size and location of all Part Numbering and Date Code identification in mold cavities shall be identified according to the approved Part Drawing when available.Use quality, approved, standard Date Codes and Plugs. See Approved Mold Standards. All methods to establish the Part Numbering and Date Code identification in mold cavities shall be approved by the Tooling Engineer prior to start of mold construction.Any deviation of Part Numbering or Date Code identification as supplied by the approved Part Drawing must be approved by the Tooling Engineer prior to start of mold construction.M)Alignment For telescoping shut-offs or critical parting line watch, straight interlocks are required.Supplier to provide Progressive Components Z-series locks.N)Cycle Counting Progressive Components’ mechanical cycle counters are acceptable.Progressive Components’ CVe monitor for potential connectivity, file storage, etc., is also acceptable.O)Cavity ID NumberingCavity identification locations must be document on the mold layout and approved by the Tooling Engineer. The layout will be based on the following chart, using the zero corner of the mold as a reference. P)Steel Treating and LubricationDetermine with the Tooling Engineer’s input and approval, the appropriate steel coatings and treatments.Learn any lubrication restrictions that the mold will be subjected to in order to determine the appropriate bushings, wear plates, and the required need for coatings within the mold.Q)DocumentationAll production molds, (Extremely High Volume, High Volume, and Medium Volume), shall be supplied from the moldmaker with a full mold documentation package that includes:Electronic copies of all detailed 3D CAD files and mold drawings. Files must contain a minimum of the following:Bill of materials for all materials and components including type of steel/material and hardness where appropriate.Detailed plan view of assembly drawings including core and cavity halves.Detailed layouts of all inserts, (front, top, right, and bottom).Section drawings of all critical areas such as slides, critical mold details, gates, etc.Runner, gating, and ejector pin layout, (size and location).Detailed hot runner or valve gate drawings showing complete manifold, all hot runner components, electrical wiring diagram and bill of materials. Detailed water line and cooling diagram.1x hard copy of detailed mold drawing with receipt of mold.Mold maker shall supply a Mold Manual at time of mold delivery that includes a minimum of the following:Copy of authorized and signed Injection Mold Specification / Request for Quotation (RFQ) Form. Mold Drawings and CAD files as requested above.Documentation of all mold and molding machine process data from Moldmaker Qualification Approval of mold at moldmaker. (See Mold Approval Section.)Documentation of actual mold steel dimensions, (all cavities), for all dimension identified as critical according to the approved Part Drawing. Tooling Engineer to determine format of documentation.Documentation of actual mold steel dimensions, (all cavities), for any additional dimension or mold detail as requested by Tooling Engineer. Tooling Engineer to determine format of documentation.Retain all documentation related to Tool Steel Certifications for mold build records.Recommended spare parts list and suppliers of critical, potential high wear, and long lead time items.Recommended mold maintenance checklist and maintenance intervals of critical, potential high wear, and long lead time components.All molds, (Low Volume and Prototype), shall be supplied from the moldmaker with documentation as requested by the Tooling Engineer at time of quotation. Moldmaker shall provide Tooling Engineer with updated electronic files of all 3D CAD files and mold drawings within 30 days of confirmation of mold approval. The Tooling Engineer will provide the moldmaker with documentation of any mold revisions or changes made to mold, (if applicable). Tooling Engineer will confirm mold approval date to moldmaker.R)Mold ShippingEliminate fluid from cooling lines, and spray the mold with a rust inhibiting mold spray.Wrap the mold with a polybag wrap to completely cover the tool.Utilize two tie straps per side of the tool, to ensure that shift does not occur along the skid and within the crate.S)Mold ApprovalThe mold approval procedure shall consist of two stages: 1. Qualification of the injection mold for shipment from the moldmaker:Moldmaker Qualification - All production molds shall be run as close to the defined production process, (estimated production molding cycle), as can be achieved with the equipment available at the moldmaker. The mold shall run long enough duration to normalize all parameters of the mold and of the molding machine. Once normalization is achieved, parts from the mold shall be gathered and identified by shot number and by cavity ID number. All Critical Dimensions, (and any additional dimensions or part features as identified by the Tooling Engineer), shall be measured, documented, and confirmed correct in accordance with the approved Part Drawing. The Moldmaker Qualification approval process is intended to confirm that the mold meets or exceeds all functionality and Process ability requirements as identified by the Tooling Engineer and Designated Manufacturing Plant Engineering. Molds shall not be approved as ready to ship from Moldmaker without full authorization of Tooling Engineer. Insure all water lines are clear of chips and debris. 2.Qualification of the mold by the Designated Manufacturing Plant:Designated Manufacturing Plant Qualification - All production molds shall be qualified by the Designated Manufacturing Plant in accordance with Plant Certification Procedures. This Procedure combines all individual mold qualification and certification procedures into one single pack of documents. The individual mold qualification procedures are:Sampling Procedure for Injection Molded PartsProcess Capability for Injection Molded PartsGage Repeatability & Reproducibility StudyCooling StudyProcess Dimension Correlation StudyProcess Dimension window StudyQualification & Certification of Injection Molded PartsT)Approved Supplier StandardsAll production molds, (Class 1: Extremely High Volume, Class 2: High Volume, Class 3: Medium Volume and Class 4: Low Volume), shall be constructed using only approved steels, materials, and components as identified in this Mold Standard. All exceptions must be approved by the Tooling Engineer in writing prior to start of mold construction. All steels, materials, and components designated as ‘Equivalent’ used to construct production molds must be approved by the Tooling Engineer prior to start of mold construction.ITEMPREFERRED STEEL AND SUPPLIERSHot Runner and Valve Gate Manifolds and ComponentsSupplier:_______________________Model: FORMTEXT ?????___________________Hot Runner and Valve Gate Temperature ControllersSupplier: FORMTEXT ?????__________________, Model: FORMTEXT ?????_________________CVe MonitorCycle CountersLocating RingSeries #: FORMTEXT ?????_________________Support Blocks/PillarsPre-hardened to 35RC or equivalentCavities and CoresCavity FORMTEXT ?????__________, Core FORMTEXT ?????_______________ . Each steel, hardness and treatment should be selected to suit the steel and application.Leader Pins & BushingsAlignment LocksGuide BushingsEjector Pins, Core Pins, SleevesDatersLifting StrapWater FittingsParting Line Sequence ControlCavity Pressure TransducersUndercut Release LiftersLimit SwitchesThree Plate Puller Pin BushingsTreatments/CoatingsMechanical Plate Staging DeviceAddendum “A”Table of Contents:Mold Standards Class Description: Page #A. Class 1: Extremely High Volume Mold Standards 13-15B. Class 2: High Volume Mold Standards16-18C. Class 3: Medium Volume Mold Standards 19-21 D.Class 4: Low Volume Mold Standards 22-23E. Class 5: Prototype Mold Standards 24Class 1: Extremely High Volume Mold Standards:Class 1: General InformationGreater than 1,000,000 lifetime cycles is expected from this mold.Mold must be constructed with valve gate or full hot runner design, assuming part configuration compatibility. No runners or sub-runner systems are allowed. Exceptions must be approved by SBU Engineering Manager and designated Manufacturing Plant Engineering Manager in writing and prior to mold construction.Mold spare parts shall be included in mold quotation package as a separate line item. Quote 25% spares for all unique non-standard mold components and details. Itemize spare parts quote.Mold shall run full automatic cycle.Mold shall produce acceptable parts at or below target estimated molding cycle as supplied by Tooling Engineer.Mold shall be built to produce 1.5 Cpk quality parts. On all critical print dimensions or additional dimensions noted by Tool Engineer, mold cavity dimensions must be held to within 10% of print tolerance to nominal. On all other print dimensions, mold cavity dimensions must be held to within 25% of print tolerance to nominal.Approved shrink factors for the selected plastic molding material shall be supplied by Tooling Engineer and documented in writing.Engineering shall supply IGES/CAD files for part dimensions, part prints, and approved title block upon release of purchase order.Tooling Engineer shall supply molding machine platen layout and ejector KO pattern in writing.Preliminary mold design shall be approved by Tooling Engineer prior to start of mold construction.Detailed mold design shall be supplied to after tool approval. Final mold designs must be updated with all mold changes prior to mold approval. See Mold ‘Drawings and Documentation’ section of this standard for complete details.Mold shall have approved vendor (Progressive Components) cycle counter.All slides shall have wear plates with grease grooves. Prefer wear plate thickness of 1/4 inch. Wear plate material shall be Ampco or Lamina. Slides shall have positive stops and locking details. All screws, bolts, leader pins/bushings, ejector pins, ejector blades, etc. shall be standard stock items wherever possible.Class 1: Mold Base (Extremely High Volume)Mold base steel hardness shall be 280 BHN minimum.All mold base plates shall be Stainless Steel material or electroless nickel plated. All steels moving against one another shall be of a dissimilar material and shall have a hardness differential of at least 4-7 Rockwell “C”.Straight alignment locks shall be on both sides of vertical and horizontal axiswherever possible. Size and location shall be approved by Tooling engineer. Eye bolt holes shall be located on all four sides and both halves of the mold base minimum. Individual plates shall have eye bolt holes located on all for sides. Eye bolt hole thread size shall be stamped near lift hole.Mold base shall be provided with two safety straps installed across parting line to insure mold does not open during shipment, installation, or removal. Mold base must have 4 inch diameter locating ring and 1/2 inch spherical radius sprue bushing, unless otherwise specified by Tooling Engineer.All mold base plates to be chamfered approximately 1/16 inch X 45 degrees.Mold base to have off-set Leader Pin/Bushings and Return Pins.Mold to have ample support pillars with minimum of 1/8 inch clearance on pillar diameter. (See page 31 for approved design.)Pry bar slots shall be located on all mold base plates. Pry bar slots to be 7/8 inch wide minimum by 3/16 inch deep minimum. Pry bar slots may be placed on corner of plates at 45 degrees angle only if no room for preferred locations. Multiple dowel pins shall be installed between plated to insure proper alignment of plates. Stamp “TOP” on top of mold, minimum 5/16 inch high.Leader Pins and Leader Pin Bushing shall be long enough to engage at least 1/2 inch prior to any other mold components. Bushings shall be self lubricating.Mold base shall have clamp slots in both halves of mold. Preferred dimension of clamp slot is 13/16 inch high X 5/8 inch deep where possible, 7/8 or 1 3/8 off top and bottom of mold. Direct bolting holes may be implemented if necessary.Class 1: Cavity and Cores (Extremely High Volume)All molding surfaces shall be made of hardened tool steel and heat treated to a minimum of 48 Rockwell “C” hardness.All mold details such as slides, heel blocks, gibs, wedge blocks, etc. shall be made of hardened tool steel and heat treated to a minimum of 48 Rockwell “C” hardness.Hardened Stainless Steel cavities, cores, and core pins shall be used wherever possible if selected plastic resin is highly corrosive.Cavities, cores, core pins, and all other molding surfaces shall be flash chrome or TIN plated wherever possible if selected plastic resin is highly abrasive. Tooling Engineer to specify type and thickness of plating.Leader pins shall be long enough engage at least 1/4 inch before core details engage cavitiesAll core pins shall be full-through hardened.All part undercuts must be formed with mechanical, hydraulic, or pneumatic slides, lifters, etc.All shut-off angles to be minimum of 3 degrees with a minimum 1/10 inch step, (assumes part design allows). Preferred shut-off angle is 5 degrees for all matching surfaces. All insert pockets shall have appropriate lead-in to assist in assembly.Excellent venting is required and shall be in accordance to plastic resin specifications. Last to fill areas must always have appropriate venting to insure ease of processing. Deep pockets must be vented wherever possible. Potential high breakage areas shall be inserted design for ease of replacement.All cavity and core details to have steel type and hardness stamped into recessed pockets wherever possible. Class 1: Cooling (Extremely High Volume)Water lines shall be in both mold halves and in cavities, cores, and slides wherever possible to allow for optimized molding cycles. Water inlet and outlet locations shall be positioned so as not to interfere with molding machine tie bars and mold clamp slots.All water inlets and outlets shall be stamped and identified on mold base. Identify inlets as “IN 1”, “IN 2”, etc. Identify outlets as “OUT 1”, “OUT 2”, etc. All water inlets and outlets must also be identified by their appropriate level on mold base. All water inlets and outlets shall be fitted with Progressive Components, DME, Jiffy type or equivalent quick disconnect fittings.Water inlets and outlets shall be recessed and installed below the mold base surface wherever possible.Water lines shall be 7/16 inch diameter or larger wherever possible.Bubblers and baffles shall be stainless steel, (preferred), or brass. Plastic bubblers and baffles are not acceptable. Baffles shall be keyed in place and secured with a set screw wherever possible.Spiral baffles shall be used wherever possible for turbulent flow.Air and vacuum fittings shall be different from water fittings to prevent misconnection and for ease of installation.Mold shall be designed with “O” ring installations such that “O” rings do not shear or become damaged during proper mold assembly.Water channels to be flash chromed when using steel other than 420 (or stainless).Class 1: Ejection (Extremely High Volume)Ejector plates shall run on guided bushings. Recommend four pins and bushingswherever possible. Bushings shall be self lubricated.Ejector plates shall have one off-set return pin.Ejector plate travel must be sufficient for full part ejection and consistent automatic molding cycle operation.Ejector pins and sleeves shall be through hardened. Ejector sleeves shall be nitridedon all inside and outside surfaces.Ejector pins and sleeves shall be industry standard sizes wherever possible. Allexceptions must be noted and approved by Engineer in writing.Contoured ejector pins located flush with core surfaces must be keyed into place to maintain core contour alignment.Cavity cores shall have ejector pin clearance of 1/64 inch larger than ejector pin diameter. Land distance shall be sized to optimize mold wear and fit characteristics.Ejector pin clearance holes in “B” plate shall be 1/32 inch larger than ejector pin diameter wherever possible.Ejector pin holes shall be 1/8 inch minimum from core side wall wherever possible. Knock-out clearance holes shall be 1 1/4 inch diameter. Tapped holes for knock-out pins/adaptors shall be 1/2 inch-13 thread size. Knock-out adapters shall be flush with back half of mold.Standard SPI knock-out patterns shall be used. Multiple KO is preferred. Tooling Engineerto provide mold supplier appropriate KO pattern to match molding machine configuration.All ejector plates shall have return springs where mold design and mold operation allows. Springs shall be standard sizes and not cut to length. Springs shall have standard diameter counter bore holes wherever possible. Springs to be installed around return pins or have separate pins in the event brokerage occurs.Class 2: High Volume Mold Standards: Class 2: General (High Volume)Up to 1,000,000 lifetime cycles is expected from this mold.Mold must be constructed with valve gate or full hot runner design, assuming part configuration compatibility. No runners are desired, however sub-runners are allowed due to mold design or cost issues. Class #102 mold runner systems must be approved by Tooling Engineer and designated Manufacturing Plant Engineering Manager in writing prior to mold construction.Mold spare parts shall be included in mold quotation package as a separate line item. Quote 25% spares for all unique non-standard mold components and details. Itemize spare parts quote.Mold shall run full automatic cycle.Mold shall produce acceptable parts at or below target estimated molding cycle as supplied by Tooling Engineer.Mold shall be built to produce 1.5 Cpk quality parts. On all critical print dimensions or additional dimensions noted by Tool Engineer. Mold cavity dimensions must be held to within 10% of print tolerance to nominal. On all other print dimensions, mold cavity dimensions must be held to within 25% of print tolerance to nominal.Approved shrink factors for the selected plastic molding material shall be supplied by Tooling Engineer and documented in writing.Engineering shall supply IGES/CAD files for part dimensions, part prints, and approved title block upon release of purchase order.Tooling Engineer shall supply molding machine platen layout and ejector KO pattern in writing.Preliminary mold design shall be approved by Tooling Engineer prior to start of mold construction.Detailed mold design shall be supplied to after tool approval. Final mold designs must be updated with all mold changes prior to mold approval. See Mold ‘Drawings and Documentation’ section of this standard for complete details.Mold shall have approved vendor (Progressive Components) cycle counter.All slides shall have wear plates with grease grooves. Prefer wear plate thickness of 1/4 inch. Wear plate material shall be Ampco or Lamina. Slides shall have positive stops and locking details. All screws, bolts, leader pins/bushings, ejector pins, ejector blades, etc. shall be standard stock items wherever possible.Class 2: Mold Base (High Volume)Mold base steel hardness shall be 280 BHN minimum.All mold base plates containing water cooling lines shall be Stainless Steel material or electroless nickel plated. All steels moving against one another shall be of a dissimilar material and shall have a hardness differential of at least 4-7 Rockwell “C”.Straight alignment locks, (Progressive Components or equivalent), shall be on both sides of vertical and horizontal axis wherever possible. Size and location shall be approved by Tooling engineer. Eye bolt holes shall be located on all four sides and both halves of the mold base minimum. Individual plates shall have eye bolt holes located on all for sides. Eye bolt hole thread sizeshall be stamped near lift hole.Mold base shall be provided with two safety straps installed across parting line to insure mold does not open during shipment, installation, or removal. Mold base must have 4 inch diameter locating ring and 1/2 inch spherical radius sprue bushing, unless otherwise specified by Tooling Engineer.All mold base plates to be chamfered approximately 1/16 inch X 45 degrees.Mold base to have off-set Leader Pin/Bushings and Return Pins.Mold to have ample support pillars with minimum of 1/8 inch clearance on pillar diameter.Pry bar slots shall be located on all mold base plates. Pry bar slots to be 7/8 inch wide minimum by 3/16 inch deep minimum. (See page 32 for recommended locations.) Pry bar slots may be placed on corner of plates at 45 degrees angle only if no room for preferred locations. Multiple dowel pins shall be installed between plated to insure proper alignment of plates. (See page 33 for recommended designs.)Stamp “TOP” on top of mold, minimum 5/16 inch high.Leader Pins and Leader Pin Bushing shall be long enough to engage at least 1/2 inch prior to any other mold components. Bushings shall be self lubricating.Mold base shall have clamp slots in both halves of mold. Preferred dimension of clamp slot is 13/16 inch high X 5/8 inch deep where possible, 7/8 or 1 3/8 off top and bottom of mold. Direct bolting holes may be implemented if necessary.Class 2: Cavity and Cores (High Volume)All molding surfaces shall be made of hardened tool steel and heat treated to a minimumof 48 Rockwell “C” hardness.All mold details such as slides, heel blocks, gibs, wedge blocks, etc. shall be made of hardened tool steel.Hardened Stainless Steel cavities, cores, and core pins shall be used wherever possible if selected plastic resin is highly corrosive.Cavities, cores, core pins, and all other molding surfaces shall be flash chrome or TIN plated wherever possible if selected plastic resin is highly abrasive. Tooling Engineer to specify type and thickness of plating.Leader pins shall be long enough engage at least 1/4 inch before core details engage cavities. All core pins shall be full-through hardened.All part undercuts must be formed with mechanical, hydraulic, or pneumatic slides, lifters, etc.All shut-off angles to be minimum of 3 degrees with a minimum 1/10 inch step, (assumes part design allows). Preferred shut-off angle is 5 degrees for all matching surfaces. All insert pockets shall have appropriate lead-in to assist in assembly.Excellent venting is required and shall be in accordance to plastic resin specifications. Last to fill areas must always have appropriate venting to insure ease of processing. Deep pockets must be vented wherever possible. Potential high breakage areas shall be inserted design for ease of replacement.All cavity and core details to have steel type and hardness stamped into recessed pockets wherever possible. Class 2: Cooling (High Volume)Water lines shall be in both mold halves and in cavities, cores, and slides wherever possible to allow for optimized molding cycles. Water inlet and outlet locations shall be positioned so as not to interfere with molding machine tie bars and mold clamp slots.All water inlets and outlets shall be stamped and identified on mold base. Identify inlets as “IN 1”, “IN 2”, etc. Identify outlets as “OUT 1”, “OUT 2”, etc. All water inlets and outlets must also be identified by their appropriate level on mold base. All water inlets and outlets shall be fitted with Progressive Components, DME, Jiffy type or equivalent quick disconnect fittings.Water inlets and outlets shall be recessed and installed below the mold base surface wherever possible. Water lines shall be 7/16 inch diameter or larger wherever possible.Bubblers and baffles shall be stainless steel, (preferred), or brass. Plastic bubblers and baffles are not acceptable. Baffles shall be keyed in place and secured with a set screw wherever possible.Spiral baffles shall be used wherever possible for turbulent flow.Air and vacuum fittings shall be different from water fittings to prevent misconnection and for ease of installation.Mold shall be designed with “O” ring installations such that “O” rings do not shear orbecome damaged during proper mold assembly.Water channels to be flash chromed when using steel other than 420 (or stainless).Class 2: Ejection (High Volume)Ejector plates shall run on guided bushings. Recommend four pins and bushingswherever possible. Bushings shall be self lubricated.Ejector plates shall have one off-set return pin.Ejector plate travel must be sufficient for full part ejection and consistent automatic molding cycle operation.Ejector pins and sleeves shall be through hardened. Ejector sleeves shall be nitrided on all inside and outside surfaces.Ejector pins and sleeves shall be industry standard sizes, (Progressive Components, DME or equivalent), wherever possible. All exceptions must be noted and approved by Tooling Engineer in writing.Contoured ejector pins located flush with core surfaces must be keyed into place to maintain core contour alignment.Cavity cores shall have ejector pin clearance of 1/64 inch larger than ejector pin diameter. Land distance shall be sized to optimize mold wear and fit characteristics.Ejector pin clearance holes in “B” plate shall be 1/32 inch larger than ejector pin diameter wherever possible.Ejector pin holes shall be 1/8 inch minimum form core side wall wherever possible. Knock-out clearance holes shall be 1 1/4 inch diameter. Taped holes for knock-out pins/adaptors shall be 1/2 inch-13 thread size. Knock-out adapters shall be flush withback half of mold.Standard SPI knock-out patterns shall be used. Multiple KO is preferred. Tooling Engineer to provide mold supplier appropriate KO pattern to match molding machine configuration.All ejector plates shall have return springs where mold design and mold operation allows. Springs shall be standard sizes, (Progressive Components, DME or equivalent), and not cut to length. Springs shall have standard diameter counter bore holes wherever possible. Springs to be installed around return pins or have separate pins in the event breakage occurs.Class 3: Class Medium Volume Mold Standards:Class 3: General (Medium Volume)Up to 500,000 lifetime cycles is expected from this mold.Prefer mold to run full automatic cycle and automatic part de-gating.Mold shall produce acceptable parts at or below target estimated molding cycleas supplied by Tooling Engineer.Mold shall be built to produce 1.33 Cpk quality parts minimum. On all critical print dimensions or additional dimensions noted by Tool Engineer. Mold cavity dimensions must be held to within 15% of print tolerance to nominal. On all other print dimensions, mold cavity dimensions must be held to within 30% of print tolerance to nominal.Approved shrink factors for the selected plastic molding material shall be supplied by Tooling Engineer and documented in writing.Engineering shall supply IGES/CAD files for part dimensions, part prints, and approved title block upon release of purchase order.Tooling Engineer shall supply molding machine platen layout and ejector KO pattern in writing.Preliminary mold design shall be approved by Tooling Engineer prior to start of mold construction.Detailed mold design shall be supplied to after tool approval. Final mold designs must be updated with all mold changes prior to mold approval. See Mold ‘Drawings and Documentation’ section of this standard for complete details.Mold shall have approved vendor (Progressive Components) cycle counter.All slides shall have wear plates with grease grooves. Slides shall have positive stops and locking details. All screws, bolts, leader pins/bushings, ejector pins, ejector blades, etc. shall be standard stock items wherever possible.Class 3: Mold Base (Medium Volume)Mold base steel hardness shall be 165 BHN minimum.All steels moving against one another shall be of a dissimilar material and shall have ahardness differential of at least 4-7 Rockwell “C”.Straight alignment locks shall be on both sides of vertical and horizontal axis wherever possible. Size and location shall be approved by Tooling Engineer. Eye bolt holes shall be located on all four sides and both halves of the mold base minimum. Individual plates shall have eye bolt holes located on all for sides. Eye bolt hole thread size shall be stamped near lift hole.Mold base shall be provided with two safety straps installed across parting line to insure mold does not open during shipment, installation, or removal. Mold base must have 4 inch diameter locating ring and 1/2 inch spherical radius sprue bushing, unless otherwise specified by Tooling Engineer.All mold base plates to be chamfered approximately 1/16 inch X 45 degrees.Mold base to have off-set Leader Pin/Bushings and Return Pins.Mold to have ample support pillars with minimum of 1/8 inch clearance on pillar diameter.Pry bar slots shall be located on all mold base plates. Pry bar slots to be 7/8 inch wide minimum by 3/16 inch deep minimum. Pry bar slots may be placed on corner of plates at 45 degrees angle only if no room for preferred locations. Multiple dowel pins shall be installed between plated to insure proper alignment of plates.Stamp “TOP” on top of mold, minimum of 5/16 inch high.Leader Pins and Leader Pin Bushing shall be long enough to engage at least 1/2 inch prior to any other mold components. Mold base shall have clamp slots in both halves of mold. Preferred dimension of clamp slot is 13/16 inch high X 5/8 inch deep where possible, 7/8 or 1 3/8 off top and bottom of mold. Direct bolting holes may be implemented if necessary.Class 3: Cavity and Cores (Medium Volume)All molding surfaces shall be made of hardened tool steel and heat treated to a minimum of 48 Rockwell “C” hardness.All mold details such as slides, heel blocks, gibs, wedge blocks, etc. shall be made of hardened tool steel heat treated to a minimum of 48 Rockwell “C” hardness.Hardened Stainless Steel cavities, cores, and core pins shall be used wherever possible if selected plastic resin is highly corrosive.Cavities, cores, core pins, and all other molding surfaces shall be flash chrome or TIN plated wherever possible if selected plastic resin is highly abrasive. Tooling Engineer to specify type and thickness of plating.Leader pins shall be long enough engage at least 1/4 inch before core details engage cavities. All core pins shall be full-through hardened.Prefer undercuts formed with mechanical, hydraulic, or pneumatic slides, lifters, etc. Exceptions must be approved by Tooling Engineer prior to start of mold construction. All shut-off angles to be minimum of 3 degrees with a minimum 1/10 inch step, (assumes part design allows). Preferred shut-off angle is 5 degrees for all matching surfaces. Excellent venting is required and shall be in accordance to plastic resin specifications. Last to fill areas must always have appropriate venting to insure ease of processing. Deep pockets must be vented wherever possible. All cavity and core details to have steel type and hardness stamped into recessed pockets wherever possible. Class 3: Cooling (Medium Volume)Water lines shall be in both mold halves and in cavities, cores, and slides wherever possible to allow for optimized molding cycles. Water inlet and outlet locations shall be positioned so as not to interfere with molding machine tie bars and mold clamp slots.All water inlets and outlets shall be stamped and identified on mold base. Identify inlets as “IN 1”, “IN 2”, etc. Identify outlets as “OUT 1”, “OUT 2”, etc. All water inlets and outlets must also be identified by their appropriate level on mold base.All water inlets and outlets shall be fitted with Progressive Components, DME, Jiffy type or equivalent quick disconnect fittings.Water inlets and outlets shall be recessed and installed below the mold base surface wherever possible.Water lines shall be 7/16 inch diameter or larger wherever possible.Bubblers and baffles shall be stainless steel or brass. Plastic bubblers and baffles are not acceptable. Baffles shall be keyed in place and secured with a set screw wherever possible.Spiral baffles shall be used wherever possible for turbulent flow.Air and vacuum fittings shall be different from water fittings to prevent misconnection and for ease of installation.Mold shall be designed with “O” ring installations such that “O” rings do not shear or become damaged during proper mold assembly.Class 3: Ejection (Medium Volume)Ejector plates shall run on guided bushings. Recommend four pins and bushings wherever possible.Ejector plates shall have one off-set return pin.Ejector plate travel must be sufficient for full part ejection and consistent molding cycle operation.Ejector pins and sleeves shall be through hardened. Ejector sleeves shall be nitrided.Ejector pins and sleeves shall be industry standard sizes wherever possible. All exceptions must be noted and approved by Tooling Engineer in writing.Contoured ejector pins located flush with core surfaces must be keyed into place to maintain core contour alignment.Cavity cores shall have ejector pin clearance of 1/64 inch larger than ejector pin diameter. Land distance shall be sized to optimize mold wear and fit characteristics.Ejector pin clearance holes in “B” plate shall be 1/32 inch larger than ejector pin diameter wherever possible.Ejector pin holes shall be 1/8 inch minimum form core side wall wherever possible. Knock-out clearance holes shall be 1 1/4 inch diameter. Taped holes for knock-out pins/adaptors shall be 1/2 inch-13 thread size. Knock-out adapters shall be flush with back half of mold.Standard SPI knock-out patterns shall be used. Multiple KO is preferred. Tooling Engineer to provide mold supplier appropriate KO pattern to match molding machine configuration.All ejector plates shall have return springs where mold design and mold operation allows. Springs shall be standard sizes and not cut to length. Springs shall have standard diameter counter bore holes wherever possible. Springs to be around return pins or have separate pins in the event breakage occurs.Class 4: Low Volume Mold Standards:Class 4: General (Low Volume)Up to 100,000 lifetime cycles is expected from this mold.Mold shall produce acceptable parts at or below target estimated molding cycle as supplied by Tooling Engineer.Mold shall be built to produce 1.33 Cpk quality parts minimum. Approved shrink factors for the selected plastic molding material shall be supplied by Tooling Engineer and documented in writing.Engineering shall supply IGES/CAD files for part dimensions, part prints, and approved title block upon release of purchase order.Tooling Engineer shall supply molding machine platen layout and ejector KO pattern in writing.Preliminary mold design shall be approved by Tooling Engineer prior to start of mold construction.Basic mold design shall be supplied to after tool approval. See Mold Drawings and Documentation section of this standard for complete details.Mold shall have approved vendor (Progressive Components) cycle counter.All screws, bolts, leader pins/bushings, ejector pins, ejector blades, etc. shall be standard stock items wherever possible.Class 4: Mold Base (Low Volume)Mold base may be of mild steel material.All steels moving against one another shall be of a dissimilar material and shall have a hardness differential of at least 4-7 Rockwell “C”.Eye bolt holes shall be located on all four sides and both halves of the mold.Mold base shall be provided with two safety straps installed across parting line to insure mold does not open during shipment, installation, or removal. Mold base must have 4 inch diameter locating ring and 1/2 inch spherical radius sprue bushing, unless otherwise specified by Tooling Engineer.All mold base plates to be chamfered and de-burred.Mold to have ample support pillars.Pry bar slots shall be located on all mold base plates. Stamp “TOP” on top of mold, minimum of 5/16 inch high.Leader Pins and Leader Pin Bushing shall be long enough to engage prior to any other mold components. Mold base shall have clamp slots in both halves of mold. Preferred dimension of clamp slot is 13/16 inch high X 5/8 inch deep where possible, 7/8 or 1 3/8 off top and bottom of mold. Direct bolting holes may be implemented if necessary. Class 4: Cavity and Cores (Low Volume)All molding surfaces shall be made of pre-hardened tool steel or tool grade aluminum approved by Tooling Engineer.All mold details such as slides, heel blocks, gibs, wedge blocks, etc. shall be made of pre-hardened steel.Leader pins shall be long enough engage before cores engage. Part undercuts may be formed with hand loaded inserts, or may be formed as a manual secondary operation. Venting is required to properly fill part.Class 4: Cooling (Low Volume)Water lines shall be in both mold halves. Water inlet and outlet locations shall be positioned so as not to interfere with moldingmachine tie bars and mold clamp slots.All water inlets and outlets shall be stamped and identified on mold base. Identify inlets as “IN 1”, “IN 2”, etc. Identify outlets as “OUT 1”, “OUT 2”, etc.All water inlets and outlets shall be fitted with Progressive Components, DME, Jiffy type or equivalent quick disconnect fittings.Water lines shall be 7/16 inch diameter or larger wherever possible.Bubblers and baffles shall be stainless steel or brass.Class 4: Ejection (Low Volume)Ejector plate travel must be sufficient for full part removal.Ejector pins and sleeves shall be industry standard sizes wherever possible.Contoured ejector pins located flush with core surfaces must be keyed into placeto maintain core contour alignment.Knock-out clearance holes shall be 1 1/4 inch diameter. Taped holes for knock-out pins/adaptors shall be 1/2 inch-13 thread size.Standard SPI knock-out patterns shall be used. Tooling Engineer to provide mold supplier appropriate KO pattern to match molding machine configuration.All ejector plates shall have return springs where mold design and mold operation allows.Class 5: Prototype Mold Standards:Class 5: General (Prototype)Mold is for prototype purpose only. Lifetime cycles are not expected to exceed 500.Approved shrink factors for the selected plastic molding material shall be supplied by Tooling Engineer.Engineering shall supply documentation for part dimensions.Mold design is not required. Tooling Engineer may request preliminary mold construction concept.Class 5: Mold Base (Prototype)Mold base may be of mild steel material or aluminum.Eye bolt holes shall be located per request of Tooling Engineer.Mold base shall have clamp slots located per request of Tooling Engineer. Class 5: Cavity and Cores (Prototype)Cores and cavities details may be cut directly into mold base material.All molding surfaces can be of mild steel, aluminum, or cast material as approved by Tooling Engineer.Part undercuts may be formed with hand loaded inserts or may be formed as a manual secondary operation. Class 5: Cooling (Prototype)Water lines, if required, shall be located per request of Tooling Engineer.Class 5: Ejection (Prototype)Ejector plate and ejector pins can be used or part may be manually removed from the mold. ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- process specification for the installation of key retained
- section 232113 13 underground hydronic piping
- section 21 1300 viking group inc viking group inc
- ndb guide specification magic aire
- mold spec guidelines
- section 09800 acoustical treatment homasote
- copper guide specifications
- section 092216 non structural metal framing
- section 12494 chged to 12493 draper inc