Inland Jet water Injection Kit Ultra 150
Congratulations you have just purchased the best kit on the market. These kits have been thoroughly tested and designed to give you flawless results. When installed properly you will notice a dramatic increase in overall performance.
Water Injected Exhaust Hop-Up Kit
Important: Read These Instructions completely before attempting this install. Look at the diagram on last page.
Warning: During Installation, Disconnect the battery cables. When disconnecting the battery, always remove the negative cable first and install it last.
Note:
Before installing the injection kit the crafts exhaust and water system must be functioning properly. The additional water supplied to the exhaust system by the injection kit is not intended to replace the original water system but to enhance it.
Note: Ultra/STXRS ‘s Find the air temp sensor then cut the 2 wires and remove sensor. Then connect the 2 wires together. This will give you 3 degrees of timing.
Remote mount
1. Locate a position on the Exhausts head pipe where a hole can be drilled and tapped without entering the water jacket (Ultra 150/stxr drill 7/16 up from front bolt resting surface). [pic] Ultra 150/stxr will need to machine down (grind) bolt head in 1/2.
2. On all other models normally, the best location to drill the hole is at the base of the head pipe where it attaches to the exhaust manifold(don’t go into jacket). [pic]
3. Use a .250 (d) drill bit and drill the hole using extreme caution not to enter the water jacket.
4. Thread the hole using a 1/16 NPT pipe tap. Install the spray nozzle so that the water will spray in the direction of the exhaust gases (up).
5. Mount the solenoid on the hull in a position away from direct engine heat sources. Connect a hose from the spray fitting to the solenoid and then from the solenoid to the main water feed line to the engine. When plumbing the system, it is recommended that a water filter be installed on the water feed line to prevent clogging of the spray nozzle.
NOTE: It is recommended that the spray nozzle be periodically checked to ensure that the spray orifice is not obstructed or clogged.
Wiring
Red: connects to positive terminal (+) side on battery.
Black: Attaches to ground stud or battery negative (-) terminal.
Long white and Red/blk: Connect to solenoid.
Yellow: Inductive Pickup. It connects directly to a spark plug wire with zip tie.
Caution: Do not mount near ignition coil or plug wires (keep grease on jumpers and fuses).
FINE TUNING: You can change jet size’s in the Spray bar and in the exhaust stinger fitting to fine tune your ski’spower band.
Programming
The activation point where the water turns on and off is easily adjusted with the built-in selector switch. The switch is set at the factory with the basic curve.
Table A –Jumper 1&2 on Amount of water
1,500 RPM Water ON
5,200 RPM Buzz 1 5/8
5,300 RPM Buzz 2 4/8
5,400 RPM Buzz 3 3/8
5,500 RPM Buzz 4 2/8
5,600 RPM Water OFF
Table B – Jumper 1 On Amount of water
1,500 RPM Water ON
5,300 RPM Buzz 1 5/8
5,400 RPM Buzz 2 4/8
5,500 RPM Buzz 3 3/8
5,600 RPM Buzz 4 2/8
5,700 RPM Water OFF
Table C – Jumper 2 on Amount of water
1,500 RPM Water ON
5,400 RPM Buzz 1 5/8
5,500 RPM Buzz 2 4/8
5,600 RPM Buzz 3 3/8
5,700 RPM Buzz 4 2/8
5,800 RPM Water OFF
Table D – Jumpers OFF Amount of water
1,500 RPM Water ON
5,500 RPM Buzz 1 5/8
5,600 RPM Buzz 2 4/8
5,700 RPM Buzz 3 3/8
5,800 RPM Buzz 4 2/8
5,900 RPM Water OFF
[pic]
909-899-7070
You can find the taps at or
Part #15990 or tool shops that sell to machinists.
-----------------------
[pic]
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- agricultural mechanics
- assembly procedures edge
- for clearance drill diameter pg 7 thru pg 13 5 add 0 1
- section 11311
- section 221000 plumbing piping accessories
- twinkie gun the hunted
- item 1104 a xx steel mast arm assembly
- the raceline cast alloy water rail is designed to simplify
- mh s metering manhole specification
- inland jet water injection kit ultra 150
Related searches
- water meth injection kit
- water methanol injection system reviews
- water injection system
- water methanol injection systems
- water injection systems tractor pulling
- water injection system for diesel
- water injection systems for cars
- water alcohol injection systems
- diesel water injection kit
- water injection for diesel
- methanol water injection systems
- water methanol injection kit diesel