Manufactured Gutters and Downspouts



Metal-Era, Inc.May 20181600 Airport RoadWaukesha, Wisconsin 53188Phone800-558-2162Fax800-373-9156WebsiteEmailinfo@Guide SpecificationSpecifier Notes: This guide specification is written in Construction Specifications Institute (CSI) 3-Part Format in accordance with The CSI Construction Specifications Practice Guide, MasterFormat, SectionFormat, and PageFormat.This Section must be carefully reviewed and edited by the Architect to meet the requirements of the Project and local building code. Coordinate this Section with Division 01, other specification sections, and the Drawings. Delete all Specifier Notes after editing this Section.Section numbers and titles are based on MasterFormat 2016 Edition. 07 71 23MANUFACTURED GUTTERS AND DOWNSPOUTSSpecifier Notes: This Section covers Metal-Era, Inc. “Seal-Tite” gutters, downspouts, scuppers, and collector boxes for drainage of roof areas, and “Garden-Tite” drain bars and inspection chambers for drainage of vegetative roof system. Consult Metal-Era, Inc. for assistance in editing this Section as required for the Project.GENERALSECTION INCLUDESSpecifier Notes: List the materials specified in this Section. Delete materials not specified.Gutters.Gutters with wood nailer alternative.Downspouts.Scuppers.Collector boxes.Drain bars for vegetative roof system.Inspection chambers for vegetative roof system.RELATED REQUIREMENTSSpecifier Notes: Edit the following list of related sections as required for the Project. Limit the list to sections with specific information that the reader might expect to find in this Section, but is specified elsewhere.Section 07 92 00 – Joint Sealants: Non-curing sealants.REFERENCE STANDARDSSpecifier Notes: List reference standards used elsewhere in this Section, complete with designations and titles. Delete reference standards from the following list not used in the edited Section.Factory Mutual (FM Global) ():FM 1-49 – Perimeter Flashing.Single Ply Roofing Industry (SPRI) ():ANSI/SPRI/FM 4435/ES-1 – Wind Design Standard for Edge Systems Used with Low Slope Roofing Systems.ANSI/SPRI GT-1 – Test Standard for Gutter Systems.PREINSTALLATION MEETINGSSpecifier Notes: Edit the Preinstallation Meetings article as required for the Project. Delete article if not required.Convene preinstallation meeting [1 week] [2 weeks] before start of installation of materials.Require attendance of parties directly affecting Work of this Section, including Contractor, Architect, installer, and manufacturer’s representative.Review the Following:Materials.Installation.Adjusting.Cleaning.Protection.Coordination with other Work.SUBMITTALSSpecifier Notes: Edit the Submittals article as required for the Project. Delete submittals not ply with Division 01.Product Data: Submit manufacturer’s product data, including installation instructions.Shop Drawings: Submit manufacturer’s shop drawings, including plans, elevations, sections, and details, indicating dimensions, materials, components, fasteners, finish, and accessories.Samples: Submit manufacturer’s sample of materials.Sample Length: Minimum 5-1/2 inches (140 mm).Color Samples: Submit manufacturer’s color samples of materials, consisting of complete color chart representing manufacturer’s full range of available colors.Specifier Notes: Include the following sentence as required for the Project. Delete if not required.Submit metal chips of specific colors as requested by the Architect.Manufacturer’s Certification: Submit manufacturer’s certification that materials comply with specified requirements and are suitable for intended application.Warranty Documentation: Submit manufacturer’s standard warranty.QUALITY ASSURANCEManufacturer’s Qualifications: Manufacturer regularly engaged in the manufacturing of materials of similar type to that specified for a minimum of 10 years.Installer's Qualifications:Installer regularly engaged in installation of materials of similar type to that specified for a minimum of 5 years.Use persons trained for installation of materials of similar type to that specified following manufacturer’s installation instructions.DELIVERY, STORAGE, AND HANDLINGDelivery Requirements: Deliver materials to site in manufacturer’s original, unopened containers and packaging.Storage and Handling Requirements:Store and handle materials in accordance with manufacturer’s instructions.Keep materials in manufacturer’s original, unopened containers and packaging until installation.Store materials in clean, dry area indoors.Do not store materials directly on floor or ground.Protect materials and finish during storage, handling, and installation to prevent damage.WARRANTYSpecifier Notes: In addition to the limited 30-year finish warranty, other finish warranty periods are available. Consult Metal-Era, Inc. for warranty period information for custom post-coated Kynar 500 colors and for anodized finishes.Warranty Period, Product: 5-year workmanship warranty covering replacement or repair of products that are defective in material or workmanship.Warranty Period, Finish: Limited 30-year warranty for prefinished coil-coated steel and aluminum coated with Kynar 500 standard colors covering fade, chalk, and film integrity.Specifier Notes: Include the following when a 20-year, 120-mph or 30-year, 160-mph gutter wind warranty is required. Delete if not required. Consult Metal-Era, Inc. for more information.Warranty Period:“Seal-Tite” Industrial Gutters: 20-year, 120-mph wind warranty.“Seal-Tite Gold” Industrial Gutters: 30-year, 160-mph wind warranty.PRODUCTSMANUFACTURERSManufacturer: Metal-Era, Inc., 1600 Airport Road, Waukesha, Wisconsin 53188. Phone 800-558-2162. Fax 800-373-9156. . info@.Specifier Notes: Specify if substitutions will be permitted.Substitutions: [Not permitted] [Comply with Division 01].GUTTERSSpecifier Notes: Specify Metal-Era, Inc. ”Seal-Tite” gutters as required for the Project. Delete gutters not required. Consult Metal-Era, Inc. for custom capabilities.Gutters: Metal-Era “Seal-Tite Gold IGG-1” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IGG1-C6] [IGG1-C7] [IGG1-C8] [IGG1-C9].Tested:ANSI/SPRI GT-1, 150 psf: 24-gauge (0.65-mm) galvanized steel and 0.040-inch (1.01-mm) aluminum.ANSI/SPRI GT-1, 210 psf: 0.050-inch (1.27-mm) aluminum and 0.063-inch (1.60-mm) aluminum.Approved: FM for wind uplift protection.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Splice Plates: 6 inches (152 mm).Gutter Hangers: 24 inches (610 mm) on center, 0.100-inch (3-mm) mill aluminum.Specifier Notes: Specify material for wind straps. Delete material not required.Wind Straps: 2 inches (51 mm) wide, 6’-0” (1,830 mm) on center, [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum].Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Gutters: Metal-Era “Seal-Tite Gold IGG-2” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IGG2-C6] [IGG2-C7] [IGG2-C8] [IGG2-C9].Tested:ANSI/SPRI GT-1, 150 psf: 24-gauge (0.65-mm) galvanized steel and 0.040-inch (1.01-mm) aluminum.ANSI/SPRI GT-1, 210 psf: 0.050-inch (1.27-mm) aluminum and 0.063-inch (1.60-mm) aluminum.Approved: FM for wind uplift protection.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Splice Plates: 6 inches (152 mm).Gutter Hangers: 24 inches (610 mm) on center, 0.100-inch (3-mm) mill aluminum.Specifier Notes: Specify material for wind straps. Delete material not required.Wind Straps: 2 inches (51 mm) wide, 6’-0” (1,830 mm) on center, [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum].Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Gutters: Metal-Era “Seal-Tite Gold IGG-3” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IGG3-C6] [IGG3-C7] [IGG3-C8] [IGG3-C9].Tested:ANSI/SPRI GT-1, 150 psf: 24-gauge (0.65-mm) galvanized steel and 0.040-inch (1.01-mm) aluminum.ANSI/SPRI GT-1, 210 psf: 0.050-inch (1.27-mm) aluminum and 0.063-inch (1.60-mm) aluminum.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Splice Plates: 6 inches (152 mm).Gutter Hangers: 24 inches (610 mm) on center, 0.100-inch (3-mm) mill aluminum.Specifier Notes: Specify material for wind straps. Delete material not required.Wind Straps: 2 inches (51 mm) wide, 6’-0” (1,830 mm) on center, [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum].Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Gutters: Metal-Era “Seal-Tite Gold IGG-B” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IGGB-C6] [IGGB-C7] [IGGB-C8] [IGGB-C9].Tested:ANSI/SPRI GT-1, 150 psf: 24-gauge (0.65-mm) galvanized steel and 0.040-inch (1.01-mm) aluminum.ANSI/SPRI GT-1, 210 psf: 0.050-inch (1.27-mm) aluminum and 0.063-inch (1.60-mm) aluminum.Approved: FM for wind uplift protection.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Splice Plates: 6 inches (152 mm).Gutter Hangers: 24 inches (610 mm) on center, 0.100-inch (3-mm) mill aluminum.Specifier Notes: Specify material for wind straps. Delete material not required.Wind Straps: 2 inches (51 mm) wide, 6’-0” (1,830 mm) on center, [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum].Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IG1-C6] [IG1-C7] [IG1-C8] [IG1-C9].Approved: FM for wind uplift protection.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IG2-C6] [IG2-C7] [IG2-C8] [IG2-C9].Approved: FM for wind uplift protection.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IG3-C6] [IG3-C7] [IG3-C8] [IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Splice Plates: 6 inches (152 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.Specifier Notes: Metal-Era “Seal-Tite IG-B” industrial gutters can also be provided in a radius version with concealed splice plates. Consult Metal-Era, Inc. for more information.Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters.Specifier Notes: Specify model. Delete models not required.Model: [IGB-C6] [IGB-C7] [IGB-C8] [IGB-C9].Approved: FM for wind uplift protection.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Fasteners:Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Nails: 1-1/4-inch (32-mm) galvanized roofing nails.Screws: #10 x 2-inch (51-mm) stainless steel screws.Tape: 6-inch (152-mm) wide EPDM/butyl pressure-sensitive tape.GUTTERS WITH WOOD NAILER ALTERNATIVESpecifier Notes: Specify Metal-Era, Inc. ”Seal-Tite” gutters with “Eliminailer-T” wood nailer alternative as required for the Project. Delete gutters not required. Consult Metal-Era, Inc. for custom capabilities.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 5.2-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (3.99-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 3-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 1.5-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 5.2-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (3.99-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 3-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 1.5-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 5.2-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (3.99-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 3-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 1.5-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 5.2-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (3.99-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 3-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 1.5-inch “Eliminailer-T”, for use with metal deck.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 5.2-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 3-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 1.5-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 5.2-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 3-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 1.5-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 5.2-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 3-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 1.5-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 5.2-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 3-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.157-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 5.2 inches (132 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 1.5-inch “Eliminailer-T”, for use with masonry walls.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.100-inch (2.54-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 5-1/2 inches (140 mm).Isolation Barrier: Between wood nailer alternative and masonry. 6-inch (152-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 3-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-B” industrial gutters with 1.5-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IGB-C6] [T-IGB-C7] [T-IGB-C8] [T-IGB-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 3-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-1” industrial gutters with 1.5-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IG1-C6] [T-IG1-C7] [T-IG1-C8] [T-IG1-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 3-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-2” industrial gutters with 1.5-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IG2-C6] [T-IG2-C7] [T-IG2-C8] [T-IG2-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-3 industrial gutters with 3-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 3 inches (76 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.Gutters: Metal-Era “Seal-Tite IG-3” industrial gutters with 1.5-inch “Eliminailer-T”, for use with wood nailers.Specifier Notes: Specify model. Delete models not required.Model: [T-IG3-C6] [T-IG3-C7] [T-IG3-C8] [T-IG3-C9].Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Fastening Holes: Slotted, 12 inches (305 mm) on center.Lap Joints: 2 inches (51 mm).Gutter Hangers: 0.100-inch (3-mm) mill aluminum, 30 inches (762 mm) on center.Termination Bars: 0.90-mm by 1-inch (25-mm) aluminum.Specifier Notes: External gutter brackets are optional. Delete if not required.External Gutter Brackets:Width: 2 inches (51 mm).Material: 0.125-inch (3-mm) aluminum.Finish: Match gutters.Color: Match gutters.Fastening Holes: 2.Specifier Notes: Specify style of expansion joints. Delete style not required.Gutter Expansion Joints: [Style1, SMACNA design] [Style 2, free-flow design, with 2-inch (51-mm) wide neoprene strip in gutter insert].Cover Plate Width: 12 inches (305 mm).Material: Match gutters.Finish: Match gutters.Color: Match gutters.Pre-slotted Fastening Holes: 2.Gutter Miters:Specifier Notes: Specify type of miter joints. Quicklock joints are standard.Miter Joints: [Quicklock] [Welded].Outside miters.Inside miters.Gutter endcaps.Rivets: 1/8-inch (3-mm) stainless steel color-matched pop rivets.Wood Nailer Alternative: “Eliminailer-T”.Tested: ANSI/SPRI/FM 4435/ES-1 to 600 pliance: FM 1-49.Material: 0.080-inch (2.02-mm) extruded aluminum, with 9/32-inch (7-mm) by 3/8-inch (10-mm) slotted holes, staggered at 6 inches (152 mm) on center.Extruded Lengths: 12’-0” (3.65 m).Height: 1-1/2 inches (38 mm).Horizontal Roof Flange onto Substrate: 2-1/2 inches (64 mm).Isolation Barrier: Between wood nailer alternative and treated wood. 3-inch (76-mm) wide EPDM/butyl pressure-sensitive isolation tape.DOWNSPOUTSSpecifier Notes: Specify Metal-Era, Inc. ”Seal-Tite” downspouts as required for the Project. Delete downspouts not required. Consult Metal-Era, Inc. for custom capabilities.Downspouts: Metal-Era “Seal-Tite” closed-face industrial downspouts.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Seams: Snap-lock.Specifier Notes: Specify style of attachment straps. Delete style not required.Attachment Straps: [Style 1] [Style 2].Width: 2 inches (51 mm).Straps per 12-Foot (3.65-m) Downspout Length: 3.Specifier Notes: Specify style of standard elbows. Delete style not required.Standard Elbows: [Style A] [Style B].Specifier Notes: Specify type of offset elbows. Delete type not required.Offset Elbows: [Wall condition] [Eave condition].Material: 0.050-inch (1.27-mm) aluminum.Finish: Match downspouts.Color: Match downspouts.Outlets: 0.040-inch (1.01-mm) aluminum.Specifier Notes: Downspout transitions are optional. Delete if not required.Downspout Transitions:Material: Match downspouts.Finish: Match downspouts.Color: Match downspouts.Specifier Notes: Specify type of seams. Quicklock seams are standard.Seams: [Quicklock] [Welded].Downspouts: Metal-Era “Seal-Tite” open-face industrial downspouts.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Specifier Notes: Specify style of attachment straps. Delete style not required.Attachment Straps: [Style 1] [Style 2].Width: 2 inches (51 mm).Straps per 12-Foot (3.65-m) Downspout Length: 3.Specifier Notes: Specify downspout spacers when Style 1 attachment straps are specified.Downspout Spacers:Width: 2 inches (51 mm).Spacers per 12-Foot (3.65-m) Downspout Length: 3.Specifier Notes: Specify style of standard elbows. Delete style not required.Standard Elbows: [Style A] [Style B].Specifier Notes: Specify type of offset elbows. Delete type not required.Offset Elbows: [Wall condition] [Eave condition].Material: 0.050-inch (1.27-mm) aluminum.Finish: Match downspouts.Color: Match downspouts.Outlets: 0.040-inch (1.01-mm) aluminum.Specifier Notes: Downspout transitions are optional. Delete if not required.Downspout Transitions:Material: Match downspouts.Finish: Match downspouts.Color: Match downspouts.Specifier Notes: Specify type of seams. Quicklock seams are standard.Seams: [Quicklock] [Welded].SCUPPERS AND COLLECTOR BOXESSpecifier Notes: Specify Metal-Era, Inc. ”Seal-Tite” scuppers and collector boxes as required for the Project. Delete scuppers and collector boxes not required.Specify material for the specified scuppers and collector boxes. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Thru-Wall Scuppers: Metal-Era “Seal-Tite”, no collector box.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [____________].Picture Frames: Front and back, 3 inches (76 mm) wide.Thru-Wall Scuppers: Metal-Era “Seal-Tite”, pop-riveted, dropped collector box, style 1.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [____________].Picture Frames: Front, 2 inches (51 mm) wide; back, 3 inches (76 mm) wide.Thru-Wall Scuppers: Metal-Era “Seal-Tite”, pop-riveted, raised collector box, style 1.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [____________].Picture Frames: Front, 2 inches (51 mm) wide; back, 3 inches (76 mm) wide.Thru-Wall Scuppers: Metal-Era “Seal-Tite”, welded, dropped collector box, style 1.Material: [0.063-inch (1.60-mm) aluminum] [____________].Picture Frames: Front, 2 inches (51 mm) wide; back, 3 inches (76 mm) wide.Thru-Wall Scuppers: Metal-Era “Seal-Tite”, welded, raised collector box, style 1.Material: [0.063-inch (1.60-mm) aluminum] [____________].Picture Frames: Front, 2 inches (51 mm) wide; back, 3 inches (76 mm) wide.Thru-Wall Scuppers: Metal-Era “Seal-Tite”, welded, dropped collector box, style 3.Material: [0.063-inch (1.60-mm) aluminum] [____________].Picture Frames: Front, 2 inches (51 mm) wide; back, 3 inches (76 mm) wide.Collector Boxes: Metal-Era “Seal-Tite”, pop-riveted, style 1.Material: [24-gauge (0.65-mm) galvanized steel] [0.040-inch (1.01-mm) aluminum] [0.050-inch (1.27-mm) aluminum] [0.063-inch (1.60-mm) aluminum] [____________].Flange: Fasten to wall, 2 inches (51 mm) wide.Collector Boxes: Metal-Era “Seal-Tite”, welded, style 2.Material: [0.063-inch (1.60-mm) aluminum] [____________].Flange: Fasten to wall, 2 inches (51 mm) wide.Collector Boxes: Metal-Era “Seal-Tite”, welded, style 3.Material: [0.063-inch (1.60-mm) aluminum] [____________].Flange: Fasten to wall, 2 inches (51 mm) wide.DRAINAGE MATERIALS FOR VEGETATIVE ROOF SYSTEMSpecifier Notes: Specify Metal-Era, Inc. “Garden-Tite” drain bars and inspection chambers as required for the Project. Delete drain bars and inspection chambers not required. Consult Metal-Era, Inc. for custom capabilities.Use of Metal-Era “Garden-Tite” drain bars and inspection chambers as drainage accessories to support a vegetative roof system may contribute to LEED credits. Consult Metal-Era, Inc. for more information.Metal-Era “Garden-Tite” drain bars can also be provided in a radius version. Consult Metal-Era, Inc. for more information.Drain Bars: Metal-Era “Garden-Tite” drain bars, maximum 6-inch (152-mm) face height.Provides drainage for plant matter on vegetative roof system.Separates growing media from roof ballast or pavers.Specifier Notes: Specify material. Delete materials not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [0.063-inch (1.60-mm) aluminum] [0.080-inch (2.03-mm) aluminum] [0.125-inch (3.18-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Drain Slots: 5/16 inch (8 mm) by 1-5/8 inches (41 mm) at 1 inch (25 mm) on center.Splice Plates: 3-1/2-inch (89-mm) wide concealed splice plates at each joint.Drain Bars: Metal-Era “Garden-Tite” drain bars, over 6-inch (152-mm) face height.Provides drainage for plant matter on vegetative roof system.Separates growing media from roof ballast or pavers.Specifier Notes: Specify material. Delete material not required. Consult Metal-Era, Inc. for information regarding other materials.Material: [0.080-inch (2.03-mm) aluminum] [0.125-inch (3.18-mm) aluminum] [____________].Formed Lengths: 12’-0” (3.65 m).Gussets: 3’-0” (914 mm) on center, welded in place.Drain Slots: 5/16 inch (8 mm) by 1-5/8 inches (41 mm) at 1 inch (25 mm) on center.Splice Plates: 3-1/2-inch (89-mm) wide concealed splice plates at each joint.Inspection Chambers: Metal-Era “Garden-Tite” inspection chambers.Provides drainage for plant matter on vegetative roof system.Provides access to internal drainage system.Specifier Notes: Specify material. Consult Metal-Era, Inc. for information regarding other materials.Material: [0.063-inch (1.60-mm) aluminum] [____________].Construction: Welded.Chambers:Size: 11 inches (279 mm) by 11 inches (279 mm) by 4-3/4 inches (121 mm) high.Drain Slots: 5/16 inch (8 mm).Base Element: 6 inches (152 mm) wide.Covers:Thickness: 1/2 inch (13 mm).Slotted Holes: 5/16 inch (8 mm) by 1-5/8 inches (41 mm).Removable.Specifier Notes: Extenders are optional. Delete if not required. If extenders are required, specify height.Extenders:Height: [1 inch (25 mm)] [3 inches (76 mm)] [8-1/2 inches (216 mm)].Drain Slots: 5/16 inch (8 mm).FINISHESSpecifier Notes: Specify finish. Delete finish not required. Consult Metal-Era, Inc. for description of the finishes available and for information regarding other finishes.Finish: [Hylar 5000/Kynar 500] [Coil anodized] [____________].Specifier Notes: Specify color. Consult Metal-Era, Inc. for standard and custom colors.Color: ____________.ACCESSORIESSpecifier Notes: Edit the following list of accessories as required for the Project. Consult Metal-Era, Inc. for factory-fabricated accessory details.Non-Curing Sealants: Specified in Section 07 92 00.Fasteners: Appropriate for intended substrate.EXECUTIONEXAMINATIONExamine areas to receive materials.Verify surfaces to support materials are clean, dry, straight, secure, and of proper dimensions.Notify Architect of conditions that would adversely affect installation.Do not begin installation until unacceptable conditions are corrected.INSTALLATIONInstall materials in accordance with manufacturer’s instructions at locations indicated on the Drawings.Remove protective vinyl film immediately before installation.Install materials to allow water to drain from edge of roof.Install materials to allow for thermal movement.Joint Sealants: Apply joint sealants in accordance with manufacturer’s instructions.ADJUSTINGRepair minor damages to finish in accordance with manufacturer’s instructions and as approved by Architect.Remove and replace with new material, damaged components that cannot be successfully repaired, as determined by Architect.CLEANINGClean materials promptly after installation in accordance with manufacturer’s instructions.Do not use harsh cleaning materials or methods that could damage finish.PROTECTIONProtect installed materials to ensure that, except for normal weathering, materials will be without damage or deterioration at time of Substantial Completion.END OF SECTION ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download