Tubing and Pipe
K
Section K
Pages
3-96
tubing and pipe
Mechanical &
Structural
Tubing
The various tubular products have been arranged in this section according to the primary end uses for which they are
manufactured:
Pages
97-107
MECHANICAL TUBING
Commercial and Aircraft Quality.
Pipe
PIPE ¡ª¡ª Steel and Aluminum
STRUCTURAL STEEL TUBING
Pages
107-112
Square and Rectangular
Structural
Tubing
AIRCRAFT STEEL TUBING
HYDRAULIC LINE TUBING
Pages
113-116
Refer to the index tabs following this page to locate information regarding the various classes of tubular products,
including
sizes,
weights,
and
technical
Aircraft
Airframe
Tubing
data.
This arrangement is presented to make it easy for you to determine the availability of tubing or pipe for a particular specification. However, it is often possible to substitute an item in one
class for a similar item in another class when the latter is not
Pages
117-128
Hydraulic
Line
Tubing
available. For example, pipe and structural tubing may often be
inter-changed, or a hydraulic tube may be used for a mechanical
application. For critical applications, though, especially when
governed by the specifications, care should be taken to insure
that the tube ordered possesses the necessary properties.
Pages
129-135
Titanium
Tubing
Sec. K Page 1
Sizes listed herein are those normally available from stock at the time of publication.
However, our stocks are continually being adjusted to reflect changing demands.
The item you need may have been added to stock after this book went to press.
If the particular item you need cannot be supplied from stock immediately, we will
endeavor to obtain it for you, either locally or from another part of the country. With
our special knowledge of tubing sources and numerous contacts in the industry,
we are in a good position to locate the hard-to-get items you need. Use this EMJ
service and your time will be free for other things.
Also, as agents of all leading tubing mills, we can expedite production and delivery
of material direct from the mill. This includes not only special sizes, but also special
analyses and grades such as the following:
12 Chrome Series
Alloy 718
A 286
Alloy 400
N 155
Alloy K-500
19-9 DL
Alloy 600
19-9 DX
Alloy X-750
17-4
Leaded Steels
17-7
Resulphurized Steels
Alloy 20Cb-3
We invite your inquiries regarding all your tubing needs.
Sec. K Page 2
ROUND STEEL AND ALUMINUM
MECHANICAL AND STRUCTURAL TUBING
Mechanical tubing is used for a wide variety of mechanical purposes as opposed
to structural and pressure applications. It is generally produced to meet specific
end use requirements which may be static or dynamic in nature.
It is available in a wide range of sizes, shapes, analyses, and mechanical properties. Compared with pipe, it is produced to closer tolerances and better finishes.
SIZES AND WEIGHTS OF MECHANICAL AND STRUCTURAL TUBING
Carbon, Alloy, and Stainless Steels; Aluminum
Round . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64
DESCRIPTION OF INDIVIDUAL GRADES
Carbon Steel:
Seamless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-70
Drawn Over Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71-74
Drawn Over Mandrel, Special Smooth ID (for Hydraulic Cylinders) . . . . . . . . 75
Cold Drawn Butt Welded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Electric ¡ª¡ª Resistance Welded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77-79
Aircraft Alloy Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80-81
Commercial Alloy Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82-83
Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84-89
Aluminum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90-96
KEY TO ABBREVIATIONS AND SYMBOLS
USED ON THE FOLLOWING PAGES
Four-digit numbers (e.g., 1018, 4130) represent analysis designations of carbon and
alloy seamless tubing. All such items are Cold Drawn except when prefixed HF.
Three-digit numbers (e.g., 304, 321) represent analysis designations of stainless
steels. Stainless tubes are seamless except where the designation includes WD,
in which case they are welded and drawn.
Four-digit number followed by temper designations (e.g., 3003-O, 2024-T3) represent alloy and temper of aluminum.
CDBW ¡ª¡ª
CREW ¡ª¡ª
HREW ¡ª¡ª
HF ¡ª¡ª
HT ¡ª¡ª
HB ¡ª¡ª
SSid ¡ª¡ª
STRUCT ¡ª¡ª
WD ¡ª¡ª
DOM ¡ª¡ª
Cold Drawn Butt Welded
Cold Rolled Electric Welded
Hot Rolled Electric Welded
Hot Finished
Heat Treated
Hollow Bar
Drawn Over Mandrel, Special Smooth ID
Structural
Welded and Drawn, Stainless
Drawn Over Mandrel, 520/1020/1026
NOTE REGARDING WEIGHTS
All weights shown herein are theoretical, and actual weight may vary according
to tolerances and chemical composition. Therefore, weights should be used for
estimating purposes only.
Sec. K Page 3
ROUND MECHANICAL TUBING
See Page 3 of this section for index to descriptions
and key to abbreviations.
Outside Wall Thickness
Diameter BWG or Decimal
(Inches) Fraction Inches
Carbon
Steel
Alloy
Steel
Stainless AlumSteel
inum
.023 .0012 .0004
321
¡ª¡ª .006
.020 .0016 .0006
321
347
34 .007
.017 .0018 .0006
33 .008
.015 .0020 .0007
31 .010
.011 .0023 .0008
347
321
304
321
1/32
36
Inside
Wt. per Foot
Diameter
(Inches) Steel Alum.
.004
¡ª¡ª .006
.051 .0036 .0013
33 .008
.047 .0047 .0017
31 .010
.043 .0057 .0020
30 .012
.038 .0065 .0023
28 .014
.035 .0073 .0026
27 .016
.031 .0080 .0028
26 .018
.027 .0087 .0031
25 .020
.023 .0092 .0032
24 .022
.019 .0096 .0034
22 .028
.006 .0105 .0037
.065
22 .028
.008 .0111 .0039
.083
31 .010
.063 .0078 .0027
1/8
¡ª¡ª .006
.113 .0076 .0026
31 .010
.105 .0123 .0043
30 .012
.101 .0145 .0051
27 .016
.093 .0186 .0065
25 .020
.085 .0224 .0078
24 .022
.081 .0242 .0085 1018/1026
22 .028
.069 .0290 .0101 1018/1026
21 .032
.061 .0318 .0112 1018/1026
20 .035
.055 .0336 .0115 1018/1026 4130
18 .049
.027 .0398 .0140 1018/1026
1/16
321
304
321
304
316
321
347
304
321
304
321
304
316
321
321
304
316
321
321
304
316
304
321
321
347
304
304
316
304
6061-T6
304WD
316
321
304
3003-O
304WD
316
321
321
304
5052-O
304WD
316
304
316
Sec. K Page 4
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- brown university rev ised march 5 facilities design
- tubing pipe mckinsey steel
- exhaust accessories donaldson company
- builder kits bends tubing components
- engine exhaust catalog
- pipe sizing what is id and od
- dom mechanical steel tubing arcelormittal
- tubing and pipe
- iecwt wall thimble catalogue drawing industrial exhaust
- walker straight tubing walker exhaust systems
Related searches
- steel tubing sizes and dimensions
- pipe od and id chart
- tubing od and id
- difference between pipe and tubing
- pipe and tubing sizes
- plastic pipe sizes and dimensions
- tubing sizes and dimensions
- tubing vs pipe strength
- pipe sizes and dimensions
- pvc pipe sizes and dimensions
- concrete pipe sizes and dimensions
- concrete pipe and precast near me