BEC MX-210NP Mini 4G/LTE X-Range Wi-Fi Router

BEC MX-210NP Mini 4G/LTE X-Range Wi-Fi

Router

Quick Start Guide

BEC MX-210NP Mini 4G/LTE X-Range Wi-Fi Router

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE. IF YOU NEED MORE INFORMATION ON THIS SOFTWARE CONFIGURATION, PLEASE REFER TO THE ONLINE USER MANUAL.

Package Contents

BEC MX-210NP 4G/LTE Router * 1 This Quick Start Guide * 1 RJ-45 Ethernet Cable * 1 4G/LTE Antenna * 2 DC Power Adapter * 1

Warning

NOTE: ALL IMAGES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY. PACKAGE CONTENTS MAY DIFFER FROM ACTUAL PRODUCTS.

Do not use the router in high humidity or at high temperature. Do not use the same power source for the router as other equipment. Do not open or repair the case yourself. If the router is too hot, turn off

the power immediately and have it repaired at a qualified service center. Avoid using this product and all accessories outdoors.

Attention

Place the router on a stable surface. Only use the power adapter that comes with the package. Using a

different voltage rating power adapter may damage the router.

1

Front Panel LEDs

Quick Start Guide

LED

Power

STATUS

DESCRIPTION

Green Red

System is up and ready Boot failure

Ethernet Port LAN 1 - 2

Green Orange Blinking

Green

Wireless

Green blinking

Orange

Green

LTE

(Received Signal

Strength Indicator)

Green Flashing quickly

Orange Flashing quickly

Orange Flashing slowly

Orange

Off

Green & Orange

Green

Red Internet

Off

Transmission speed is at Gigabit speed (1000Mbps) Transmission speed is at 10/100Mbps Data being transmitted/received Wireless connection established Data being transmitted / received WPS configuration is in progress RSSI greater than -69 dBm. Excellent signal condition

RSSI from -81 to -69 dBm. Good signal condition

RSSI from -99 to -81 dBm. Fair signal condition.

RSSI less than -99 dBm. Poor signal condition.

No signal and the cellular module is in service No LTE module or LTE module fails MX-210NP is either in debug mode or in upgrading firmware process IP address has received; traffic is passing thru the device. IP address request has failed. MX-210NP is either in bridged mode or WAN connection not ready.

2

Rear Panel Connectors

BEC MX-210NP Mini 4G/LTE X-Range Wi-Fi Router

INTERFACE

4G/LTE Antenna 1 Connectors

(Main/Aux)

2 Power Source Power Jack

3 (DC IN)

4 Reset

Gigabit Ethernet 5

(LAN 1 / PoE)

Gigabit Ethernet 6

(LAN 2 / EWAN)

7

GPS Antenna Connectors

8 SIM Card Slot

MEANING

SMA female connectors. Manually screw the cellular antennas tight to the female connectors. Connect to Main if decide to use single antenna instead of two.

Power ON/OFF switch (1) with Power Switch ON: power up by the supplied DC power adapter (2) with Power Switch OFF: power up by the PoE battery unit

Connect the supplied Power Adapter to this jack.

After the device is powered on, press it 6 seconds or above: to restore to factory default settings (this is used when you cannot login to the router, e.g. forgot your password)

Ethernet LAN: Connected to a 10/100/1000Mbps Ethernet device

Ethernet PoE: Connect to an 802.3at Gb PoE injector to provide power to the

MX-210NP

Ethernet LAN: Connected to a 10/100/1000Mbps Ethernet device Ethernet WAN: Software configurable in the GUI. Connect to a broadband device such as a cable modem, ADSL/VDSL modem or fiber modem.

SMA female connectors. Manually screw the GPS antenna tight to the female connector.

Insert the mini SIM card (2FF) with the gold contact facing down. Push the mini SIM card (2FF) inwards to eject it * Power off the MX-210NP before inserting or removing the SIM card(s)

3

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download