IMPORTANT SAFETY INFORMATION
IMPORTANT SAFETY INFORMATION
WARNING Read all safety warnings and instructions. Failure to heed these markings may result in personal injury and/or property damage. Save all warnings and instructions for future reference. The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors, which cannot be built into this product, but must be supplied by the operator.
1. Study, understand, and follow all instructions before operating this device.
2. To prevent electric shock, connect motor to device according to the instructions detailed in this manual.
3. Be aware of moving parts during use.
4. Do not block motor air vents during use.
5. Verify all mounting hardware is securely fastened before use.
6. Maintain labels and nameplates on the Motor. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement.
7. Wear ANSI-approved safety eye goggles and heavy-duty work gloves when setting up, using or servicing the Motor. Using personal safety devices reduce the risk for injury.
8. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use or install the motor in areas near flammable chemicals, dusts, and vapors. Do not use this motor in a damp or wet location.
9. Do not overload Motor. This motor will work better and safer at the speed and capacity for which it was designed.
10. Unplug the Motor from its electrical outlet (or turn off the circuit breaker and tag it) before performing any inspection, maintenance, or cleaning procedures.
11. When installing motor, observe all national and local codes. Install, protect, and fuse according to the latest issue of the National Electric Code, NEMA Standard Publication No. MG2, and local codes. Ground frames in accordance with NEC Article 430. For general grounding information, refer to NEC Article 250.
12. Install safety guards when appropriate. Make sure all moving parts, including the shaft and any attached accessories, are permanently guarded to prevent clothing and body parts from being caught.
13. Before each use, check all nuts, bolts, and screws for tightness. Vibration during operation may cause these to loosen.
14. Connect Motor through a properly rated fuse or circuit breaker.
15. Do not allow children or unauthorized personnel to play with, or handle this motor.
16. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
Specifications
Item Type
Input
HP RPM Capacitor Frame
67839 General Purpose 115 / 230V~, 60Hz, 1 Phase 1/2 1800
Start
NEMA 56
68288 Farm Duty 115 / 230V~, 60Hz, 1 Phase 1 1800
Start
NEMA 56
60814 Compressor Duty 115 / 230V~, 60Hz, 1 Phase 1 1/2 3600
Dual
NEMA 56
67842 Compressor Duty 115 / 230V~, 60Hz, 1 Phase 2 1800
Dual
NEMA 145
68302 Compressor Duty 230V~, 60Hz, 1 Phase 3 3600
Dual
NEMA 56
Page 2
For technical questions, please call 1-888-866-5797.
Electric Motor
Installation Instructions
1. The ambient air temperature where the motor is to be installed cannot exceed 104? F. If it might, cooling must be provided to ensure the temperature stays below the limit.
2. Install with proper ventilation, making sure to keep away from any moisture.
3. Install indoors in a dry and noncorrosive environment where no flammable liquids or gases are present.
4. When mounting motor, make sure all hardware is securely fastened.
5. When mounting a pulley (not included) to the drive shaft, make sure pulley and shaft are properly aligned or motor life will be significantly shortened.
6. Do not operate motor without installing a safety guard (not supplied), with at least a two inch clearance, around all pulleys and belts driven by motor.
7. Allow for enough room for changing the belt (if attached).
Motor Wire Connections
Figure B: Wiring Diagram indicates the proper wiring connections for each individual motor's internal wires and the external power connections.
"CCW" stands for counterclockwise motor shaft rotation and "CW" stands for clockwise shaft rotation.
Note the markings on the internal wires (i.e., "T3, T4, P1, P2," etc.) and use them as reference for wiring your specific motor.
WARNING! Verify that there is no power to circuit to be connected. Check fuse box and turn off circuit breaker. Also tag breaker switch to prevent accidental shock.
1. Remove Connection Cover to expose the terminal strip. See Figure A.
2. Using approved National Electrical Code electrical standards, connect as described in Figure B. The facility power circuit, and connecting wires, must be rated to at least 20 amps of current. Use wire lugs (not included) to connect the wires to the Motor terminal strip. The motor can be connected by an appropriate size line cord (not included) or hard wired through conduit.
Terminal Strip
3. WARNING! Connect ground wire to ground screw marked . Do not leave loose.
4. Replace motor Connection Cover.
ITEM's 67839, 60814, 67842, and 68288
Connection Cover
Figure A: Connection Cover Open ITEM 68302
CCW
CW
P1
L1
P1
P2
P2
T3
T3
T8
T5
T2
T2
T4
L2
T4
T5
T8
CCW
P1
L1
P2
T3
T8
T2
T4 T5
L2
CW CCW
CW
P1 P1
L1
P1
P2 T1 T3 T8 T5 T2 T4 T4 T5
T1 T5
L2
T4 T8
T8
230V~
115V~
230V~
Figure B: Wiring Diagram Note: All rotation directions are Lead-End (LE), or as viewed from wires at back of motor.
Electric Motor
For technical questions, please call 1-888-866-5797.
Page 3
Operation
Before initial operation, verify that motor is dry and all connections to the motor are correct.
1. Verify the rotor turns freely when disconnected from the load.
2. Also verify the motor is detached from the load for the initial start.
3. Check that the voltage is correct and balanced at the motor terminals and that the no-load current draw is correct.
NOTE: Make sure motor is not being overloaded once it comes to its operational speed (see Specifications chart for each motor's specific RPM).
Note: If motor suddenly stops, check that its rotation is not limited or blocked, then press the reset button on the switch box. If the problem persists, check voltage supply and contact a qualified technician.
Inspection, Maintenance, and Cleaning
Procedures not specifically explained in this manual must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure the Motor circuit breaker is off before performing any inspection, maintenance, or cleaning procedures.
1. Before each use, inspect the general condition of the Motor. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment.
2. Periodically recheck all nuts, bolts, and screws for tightness.
Lubrication
1. Re-oil sleeve bearings with drops of 5W20 viscosity motor oil every 2000 hours of normal service. Direct drive operation (no pulleys) requires lubrication every 3000 hours of normal service.
2. Sealed ball bearings require no attention during the life of the bearing.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. ? PO Box 6009 Camarillo, CA 93011 ? 1-888-866-5797
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- 8 to 18 hp cast iron four cycle engines
- replacement parts franklin electric
- standard motor catalogue teco
- important safety information
- oem replacement motors universal electric motors
- 2022 ford maverick tech specs ford motor company
- nema motor dimensions reference chart
- submersible pumps franklin electric
- baldor motor basics power systems and voltage
- the green box ucf department of eecs
Related searches
- water safety crafts for preschoolers
- important information synonym
- important to vs important for
- important for or important to
- important information for senior citizens
- important quotes from important people
- information on or information about
- why are safety rules important reasons
- information technology vs information system
- safety topics for safety meetings
- reference safety information fda
- reference safety information eu