BASIC ENGINE CONCEPT
Basic Engine Concepts WVEIS Code 1623
This course will introduce students to basic engine concepts, skills, technology and service of the automobile.
Standard 1: Perform general engine diagnosis, removal and reinstallations (R&R). (1623.S.1)
General Engine Diagnosis, Removal and Reinstallations (R&R) Objectives
Students will:
1623.1.1 Interpret and verify complaint; listen to engine noises; inspect engine assembly for fuel, oil, coolant, and other leaks; determine needed repairs.
1623.1.2 Diagnose the cause of excessive oil consumption, unusual engine exhaust color, odor, and sound; determine needed repairs.
1623.1.3 Perform engine vacuum tests; determine needed repairs.
1623.1.4 Perform cylinder power balance tests; cylinder compression tests; cylinder leakage tests; determine needed repairs.
1623.1.5 Remove engine (front-wheel drive); prepare for disassembly; reinstall engine.
Standard 2: Demonstrate cylinder head and valve train diagnosis and repair. (1623..S.2)
Cylinder Head and Valve Train Diagnosis and Repair Objectives
Students will:
1623.2.1 Remove cylinder head(s); inspect cylinder head(s) for cracks; check gasket surface areas for warpage and leakage; check passage condition.
1623.2.2 Install cylinder heads and gaskets; tighten according to manufacturer’s specifications and procedures.
1623.2.3 Inspect and test valve springs for squareness, pressure, and free height comparison; inspect valve spring retainers, locks, and valve grooves; replace as needed. Replace valve stem seals.
1623.2.4 Inspect valve guides for wear; check valve guide height and stem-to-guide clearance; inspect valves; inspect valve seats; recondition or replace as needed.
1623.2.5 Check valve face-to-seat contact and valve seat concentricity (run out), service seats and valves as needed.
1623.2.6 Check valve spring assembled height and valve stem height; service valve and spring assemblies as needed.
1623.2.7 Inspect pushrods, rocker arms, rocker arm pivots and shaft for wear, bending, cracks, looseness, and blocked oil passages (orifices); repair or replace.
1623.2.8 Inspect hydraulic or mechanical lifters; replace as needed. Adjust valves (mechanical or hydraulic lifters).
1623.2.9 Inspect and replace camshaft drives (including gear wear and backlash, sprocket and chain wear, overhead cam drive sprockets, drive belts, belt tension, and tensioners).
1623.2.10 Inspect camshaft for run out, measure journals and lobes for wear.
1623.2.11 Inspect and measure camshaft bearings for wear, damage, out-of-round, and alignment; determine needed repairs.
1623.2.12 Verify camshaft(s) timing according to manufacturer’s specifications and procedure.
Standard 3: Perform engine block diagnosis and repair. (1623.S.3)
Engine Block Diagnosis and Repair Objectives
Students will:
1623.3.1 Inspect and replace pans, covers, gaskets, and seals.
1623.3.2 Inspect engine block for cracks, passage condition, core and gallery plug condition, and surface warpage; determine needed repairs.
1623.3.3 Inspect internal and external threads; repair as needed.
1623.3.4 Inspect and measure cylinder walls for damage and wear; determine needed repairs. Remove cylinder wall ridges. Deglaze and clean cylinder walls.
1623.3.5 Inspect crankshaft for surface cracks and journal damage; check oil passage condition; measure journal wear; determine needed repairs.
1623.3.6 Inspect and measure main and connecting rod bearings for damage, clearance, and end play; determine needed repairs (includes the proper selections of bearings).
1623.3.7 Identify piston and bearing wear patterns that indicate connecting rod alignment and main bearing bore problems; inspect rod alignment and bearing bore condition.
1623.3.8 Inspect, measure, service or replace pistons. Inspect, measure, and install piston rings.
1623.3.9 Inspect, repair or replace crankshaft vibrations damper (harmonic balancer).
1623.3.10 Inspect flywheel or flex plate and ring gear for cracks and wear; measure run out and determine needed repairs.
1623.3.11 Inspect, remove, and replace crankshaft pilot bearing or bushing (as applicable).
1623.3.12 Reassemble engine components using correct gaskets and sealants.
1623.3.13 Inspect auxiliary (balance, intermediate, idler, counterbalance or silencer) shaft(s); inspect shaft(s) and support bearings for damage and wear; determine needed repairs; reinstall and time.
1623.3.14 Prime engine lubrication system.
Standard 4: Perform lubrication and cooling systems diagnosis and repair. (1623.S.4)
Cooling Systems Diagnosis and Repair Objectives
Students will:
1623.4.1 Perform oil pressure tests; inspect oil pump ears or rotors, housing, pressure relief devices, and pump drive; replace as needed.
1623.4.2 Perform cooling system tests (pressure, combustion leakage, and temperature) determine needed repairs.
1623.4.3 Inspect, replace, and adjust drive belts and pulleys.
1623.4.4 Inspect and replace engine cooling and heater system hoses.
1623.4.5 Inspect, test, and replace thermostat and housing.
1623.4.6 Inspect coolant; drain, flush, and refill cooling system with recommended coolant and bleed air as required.
1623.4.7 Inspect, test, remove, and replace water pump.
1623.4.8 Inspect and test radiator, pressure cap, and coolant recovery system; remove and replace radiator.
1623.4.9 Clean, inspect, and test fan(s) (electrical or mechanical), inspect and test electrical fan control system and circuits, fan clutch, fan shroud and air dams.
1623.4.10 Inspect, test, and replace oil temperature and pressure switches and sensors. Inspect auxiliary oil coolers; replace as needed.
1623.4.11 Perform oil and filter change.
[pic]
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- basic car engine diagram
- basic car engine parts diagram
- basic engine parts
- basic engine components and functions
- basic small engine repair
- speech language basic concept development
- calculate engine horsepower engine specs
- basic diesel engine components
- basic car engine parts
- list of basic concept words
- chapter 6 lesson two concept map concept practice alesson two
- basic engine components