STONE CREEK 600 PARTS LIST



STONE CREEK 600 PARTS LIST

W4NFR

Quantity Description Manufacturer

EB104, 600 Watt Amplifier Kit, Communications Concept Inc.

1 Capacitor Kit $9.75

1 Resistor Kit $9.75

1 Semiconductor Set $2.80

1 Ferrite Set $1.75

1 Transformer Set $18.40

1 PC Board (3.625” x 5.125”) $24

1 MRF150 Matched Quad Transistor Set (MosFet) (4 each) $256 Total

1 Model 55 Heat Sink, 8” Long x 6” Wide x 0.375” Thick, CHS-6, $52.00

2 KILOVAC GH1 Vacuum Relays, 12 VDC Coil, Fast Switching, $64 each Henry Radio

2 SO-239 UHF Female Connectors, $2 each

Harmonic Filters *

1. FL-160 Kit, $14 (Filter Kits From Communications Concept Inc.

1. FL- 80 Kit, $14

1. FL- 40 Kit, $14

1. FL- 20 Kit, $14

1. FL- 15 Kit, $14

1 FL- 10 Kit, $14

12. Relays, SPST for Harmonic Filter Selection

* Note: I did not use the CCI Harmonic Filters. I used the MFJ Ameritron ARF-1000 Filter and it worked much better.

Power Supply

1. Diode Bridge, 30 AMP@ 600 VDC MDA990-6, $10

1 Toroid Corp of Maryland, Model : 182V40, TCM Part # 782-382, 117 VAC/220 VAC

Primary, 38 V @ 2.5 Amp Secondary, 25 lbs (7.2” Dis x 3.5” High) $130 + Ship

1. 100,000 uF @ 63 VDC Filter Capacitor

1. 0-1 mA Meter Voltage, $11

1. 0-30 Amp Meter Current, $12

1. Shunt for Current Meter, $10

1 Hammond Enclosure Model 1453K, 9” x 10” x 17”, $80

2. Filtron Line Filters for AC, $10

2. .02 @ 600 V Disc Capacitors, $ 1

1. Filter Switch, 2P9T, To Switch Harmonic Relays and LED Band Indicators, $10

1. 4” Fan, 50 CU FT/Min, 12 VDC, $15

1. 12 VDC Panel Mount, RED LED for TX On Indicator, No Resistor Required. $2

9. LEDs, Red, Band Indicators, Panel Mount, 1.6 VDC @ 0.95 mA, (Requires 11K), $20

(Surplus Sales of Nebraska)

2. LEDs Green, (Opr/Stby) and (Power On/Off), No Resistor Needed, 12 VDC, $2

1. DPDT S2 Switch, Vapor Tight (Opr/Stby) $5

1 SPST S1 Switch, Vapor Tight (AC ON Switch) $5

12. RF Capacitors Disc 0.1 @ 250 VDC $12

1. 10k 5 Watt Resistor $4

1. .047 Capacitor @ 600 Volts, $3

1. K1 Relay, 120 VAC DPDT HDAC Switching Contactor, $15

1. LM-7812 Regulator Chip, $1

1. 12 VDC PS Diode Bridge, $ 5

1. T2 Transformer, 120 VAC to 12 VAC @ 4 Amp, $10

1. 25,000 uF @ 50 Volt Capacitor for LV PS, $10

12. Diodes, 1N4007

2. Capacitor 1 uF @ 50 Volts

2. 8.2 ohm @ 30 Watt Non Inductive Resistor, MP930, 1%, $5

1. 150 ohm @ 30 Watt Non Inductive Resistor, MP930, 1 %, $5

2. Black Handles, 4” x 1” with Screws, $8

2 Resistor 10 ohm @ 30 Watt, MP930 (Feedback Resistors, Non Inductive,

(Must Heat sink)

1. 11 K ohm Resistor for Band Select LEDs, $.50

1. Small Inline (10 Pin) wire connector, Molex $3

1. Cinch Jones Inline Connector for 50 Volt Line (Male and Female), $ 6

Set Hardware # 4-40, 1” Screws and Nuts and Star Washers. Uses 12 For Amp Bd

# 6 and # 8 Screws and Nuts and Star Washers.

1 Drill and Tap for #4-40, to tap the holes in Copper Heat spreader.

Set Lots of Hookup wire, I prefer Teflon, for Hookup….Aluminum stock….

1 AC Power Cord and 3 Pin Power Plug, 6’long $10

1. 12” x 12” PC Board Plain Single Sided for RF Shield Around Harmonic Filter Stack

$5 /Sheet

3. 10 Terminal Barrier Strips, $5 each

-The End-

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download