Warranty & Support - Global Technology Systems



|Charger Mode |

|Rapid Charge |Solid Red |

|Charging complete |Solid Green |

|Battery is over temp |Flash Red |

|System Fault – Remove Battery |Flash Red |

-----------------------

ν Warranty & Support:

Global Technology Systems, Inc. pro畤瑣⁳牡⁥敤楳湧摥琠敢挠浯汰慩瑮眠瑩⁨桴⁥畲敬⁳湡⁤敲畧慬楴湯⁳湩琠敨氠捯污瑩敩⁳湩眠楨档琠敨瀠潲畤瑣⁳牡⁥潳摬愠摮眠汩敢氠扡汥摥愠⁳敲畱物摥‮桔⁥楬業獴愠敲搠獥杩敮⁤潴瀠潲楶敤爠慥潳慮汢⁥牰瑯捥楴湯愠慧湩瑳栠牡晭汵椠瑮牥敦敲据⁥桷湥攠敬瑣潲楮⁣敤楶散⁳牡⁥灯牥瑡摥椠⁡潣浭牥楣污攠癮物湯敭瑮മ䘍牯眠牡慲瑮⁹湡⁤敳癲捩⁥湩潦浲瑡潩慣汬ㄠ㔭㠰㘭〵ㄭ㜱⸲传瑵楳敤丠牯桴䄠敭楲慣‬汰慥敳挠湯慴瑣ducts are designed to be compliant with the rules and regulations in the localities in which the products are sold and will be labeled as required. The limits are designed to provide reasonable protection against harmful interference when electronic devices are operated in a commercial environment.

For warranty and service information call 1-508-650-1172. Outside North America, please contact your local Global Technology Systems representative.

Each charger is guaranteed to be free from defects in materials and workmanship for 24 months from date of shipment under normal use.

The charger must remain unmodified and must be operated under normal and proper conditions.

The warranty is limited to repair or replacement at Global Technology System, Inc., with reasonable promptness after being returned and received by Global Technology System, Inc. These provisions do not extend the original warranty term for any product or device which was repaired or replaced. This warranty applies to the original owner and does not extend to any product or device which was subject to misuse, neglect, accidental damage, unauthorized repair or tampering. Preventive maintenance activities are not covered by this warranty.

ν For additional information or replacement parts, please contact:

Global Technology Systems, Inc.

550 Cochituate Road

Framingham, MA 01701 USA

In the US 1-800-267-2711



ν About Global Technology Systems, Inc. batteries

GTS® and Honeywell® Batteries are available for hand-held bar code scanners/mobile computers, portable printers, two-way radios, and uninterruptible power supply systems (UPS). We also produce a line of battery chargers and design custom applications for clients' specific mobile power needs. We are proud to be a respected leader in mobile power technology, design and development.

The cornerstones of our business are product quality, customer service and attractive pricing. We look forward to serving you.

Copyright 2008 Global Technology Systems, Inc. All rights reserved.

Global Technology Systems, Inc. reserves the right to make changes to any product to improve function, reliability, or design.

Changes or modifications not expressly approved by Global Technology Systems, Inc. may void the warranty and the user's authority to operate the device.

No license is granted, either expressly or by implication, estoppels, or otherwise under any patent right or patent, related to or covering any combination, system, apparatus, machine, materials, methodology or process in which Global Technology Systems, Inc. products might be used. An implied license only exists for equipment, circuits, and subsystems contained in GTS products.

M/A-COM® is a trade mark of M/A-COM,Inc.

The Honeywell® Trademark is used under license from Honeywell® International Inc.

ν 12 / 24 VDC POWER CONNECTOR INFORMATION:

ν The Shell is Amphenol Part Number: 97-3106A22-2P

ν The Back Shell / Cable Clamp is Amphenol Part Number: 97-3057-1012

ν The Cable Bushing is Amphenol Part Number: 9779-513-12

ν A length of 10 Gauge Red Stranded Wire cut to length will be required.

ν Two lengths of 10 Gauge Black Stranded Wire cut to length will be required.

ν A length of desired sleeving will be required to protect the cable.

ν An appropriate number of tie wraps will be required, evenly spaced to bundle the cable.

ν Compatible Batteries:

The following listing is comprised of supported batteries as determined by Honeywell Battery Services, which are approved for use with the Honeywell HCH-P7101 Multi-Chemistry charger.

GTS / Honeywell Batteries: P7100 series

|Battery Model |Capacity |Chemistry |

|HMA2104-LiP* |3600mAh |Li-Ion Polymer |

|HMA2104-M |2700mAh |NiMH |

|HMA2104-C |1700 mAh |NiCd |

M/A-COM: P7100 series

|Battery Model |Capacity |Chemistry |

|BKB 191 - 210/3 |1700mAh |NiCd |

|BKB 191 - 210/4 |2700mAh |NiMH |

|BKB 191 - 210/5 |2700mAh |NiMH |

|BKB 191 - 210/6 |2700mAh |NiCd |

|BKB 191 - 210/33 |1700mAh |NiCd |

|BKB 191 - 210/34 |2700mAh |NiMH |

|BKB 191 - 210/35 |2700mAh |NiCd |

|BKB 191 - 210/36 |2700mAh |NiMH |

|BKB 191 - 210/44 |2700mAh |NiMH |

*Only recharge the Honeywell Batteries HMA2104-LiP battery in an authorized Honeywell Batteries battery charger

ν Safety Guidelines & Warnings:

ν Before using this Charger, please read all instructions and cautionary notations on the

Charger, the GTS® and Honeywell® Battery, any OEM batteries, and on the host device.

ν To reduce risk of injury, only use authorized battery products with this charger. Other non-approved batteries may cause personal injury and / or damage to the equipment.

■ Do not expose the charger to excessive moisture, temperature extremes or direct sunlight.

■ Place charger in a well ventilated area, which is free of foreign materials.

■ To reduce risk of electric shock, unplug charger from power source before cleaning.

■ Dispose of used batteries in accordance with your state or local hazardous material

laws.

■ Do not disassemble, incinerate, modify, or short circuit the charger, any battery, or

related components.

ν Troubleshooting:

If the Charger does not operate after you have followed the previous operating instructions, then please try the following:

ν Check the circuit breakers to ensure that none have tripped.

ν Check for loose cable, or power cord connections.

ν Check to insure the battery, or radio is properly inserted into the charging slot.

■ Ensure that the lid closure detect switch isn’t accidentally depressed.

ν CAUTION:

Do not pour, spray or spill any liquid into or onto the charger. If liquid does come into contact with the charger, immediately un-plug the charger and remove any batteries.

ν Unit Description:

■ The EOCC Emergency Operations Center Charger is designed to provide a transportable, rugged, and highly reliable means of charging up to 18 radios or radio batteries at one time. It is designed to be used in field operations, and has the ability to receive its power from either AC or DC power sources – providing flexibility in emergency situations. The input power can be either 120 or 240 VAC, connected by a conventional commercial extension cord. The DC power sources can be 12 or 24 VDC supplied by either a 12 V system vehicle, or a 24 V system vehicle (such as a Humvee, or Fire Engine), or from a 24 V source via an optionally installed NATO Slave Receptacle.

■ WARNING: If the EOCC is run in DC mode directly off of a car battery, the unit will quickly deplete the external battery – the vehicle’s engine needs to be running to supply this much power.

ν Operation

1. DO NOT USE THE UNIT IN DIRECT RAIN OR WATER. With the lid closed the EOCC is water resistant, but is NOT immersion capable. With the lid open prevent any water from entering the unit, as there are necessary ventilation slots and openings which could allow water into the interior of the unit causing the possibility of short circuits, and serious internal damage.

2. Plug the AC power supply into the wall and the power cord into the charger

a. It is recommended that a grounded three (3) prong AC outlet be used to power this device.

b. The input connector for the AC power is located on the rear panel and accepts a standard 3 prong single output heavy gauge extension cord cable.

c. The user should insure that the AC outlet is grounded before using this device. If you are not sure that the AC outlet has appropriate ground, we suggest that a qualified electrician be called for verification.

d. A temporary grounding adapter can be used to properly ground a two (2) prong outlet.

e. If run with an AC generator, the generator needs to be 500 Watts minimum.

3. Alternately the unit can be powered from a DC power source such as a Police car, a Fire Engine, or when using the optional NATO Slave receptacle and mating cable – a humvee, tank, armored personnel carrier, or other military vehicle. The input power cable should have a minimum of 10 gauge power wire, soldered to the DC input power connector. The mating plug on the EOCC is an Amphenol thread locking circular military plug. Additional detail on the external cable and connector is provided later in this manual.

4. Ensure that the EOCC charger cups air slots are unobstructed and adequate ventilation is provided. Do not use the EOCC in a completely closed cabinet. The unit will automatically shut off when the top lid is closed.

5. Insert a battery or a radio into any charger socket. The cup will start to charge when it detects the presence of a battery and the battery is within normal temperature limits. When charging, the Charge LED will be red. Please see the LED indications in Product Specification later in this manual.

ν Cleaning

Periodically wipe the EOCC with a slightly damp cloth or other cleaning materials suitable for use on electrical devices.

[pic]

[pic]

EOCC-P7100-12V Emergency Operation Center Charger (EOCC)

18 bay Multi-Chemistry Cradle and Battery Chargers for

HARRIS - M/A-COM® P7100 Series Radio Batteries.

[pic]

ν Equipment Supplied

ν One (1) EOCC-P7100-12V

■ One (1) Operations Manual

ν Product Specifications:

Chemistries Supported: Li-Ion, Li-Polymer, NiMh, NiCd

Operating Temperature: 0°C to +60°C (+32°F to +140°F)

Battery Temperature: 0°C to +50°C (+32°F to +125°F)

Storage Range: -20°C to +70°C (-4°F to +158°F)

Charge Time: Up to 5 hrs maximum

(varies with battery capacity)

Charge Current: Up to 1000mA in Constant Current Charging Phase

Charge Method: Li-Ion / Li-Polymer : CC-CV

NiMH / NiCd : CC

Electrical Requirements: AC power source (External Extension Cord):

120 to 240 VAC.

At 120 VAC requires 2 Amps. (240 Watts)

At 240 VAC requires 1 Amp, when fully loaded and charging. (240 Watts) Max 250 VAC.

DC power sources (Circular Mil Spec Connector, or Optional NATO Slave Connector):

10.5 to 32 VDC.

At 12 VDC requires 20 Amps. (240 Watts).

At 24 VDC requires 10 Amps, when fully loaded and charging. (240 Watts) Max 32 VDC.

EOCC External Dimensions: The case is a standard Pelican case with the dimensions of: 78.1 cm (30.75”) wide X 52 cm (20.5”) deep X 29.5 cm (11.6”) high.

EOCC Unit Weight: 23.6 Kg (52 lbs)

ν Led Operation:

DC POWER CONNECTOR WIRING

[pic]

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download