LEW Series Installation Instructions
LEW Series Installation Instructions
SAFETY INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND SAVE THEM, AS YOU MAY NEED THEM AT A LATER DATE.
1. WARNING: Failure to install and wire fixture in accordance with the National Electrical Codes (NEC), all applicable Federal, State and Local electrical codes, as well as specific UL safety standards for the intended working environment (location/application), may cause serious personal injury, death and or property damage. This product must be installed by a person familiar with the construction and operation of the product and the hazards involved.
2. IMPORTANT NOTE: The safeguards and instructions appearing on this page, are not meant to cover all possible conditions and situations that may occur. It may be understood that common sense, cautions and care are factors which cannot be built into any product. The person who's installing, operating and responsible for the light fixture, must execute these factors.
3. PRECAUTIONS: - Turn off power from the main Circuit Breaker before installing the fixture. - Make sure fixture is grounded per National Electrical Code (NEC). - To help prevent the possibility of electrical shock, the use of rubber sole shoes is recommended. - Use work gloves when handling the fixture to avoid cut or abrasions. - If supply wires are located within 3 inches of the ballast, use wires rated at least 90?C.
NEEDED TOOLS
Safety Glasses Ruler/Tape Measure Flat Blade Screwdriver Phillips Screwdriver Adjustable Wrench
INSTRUCTIONS
Drill 3/16" Drill Bit 3/32" Drill Bit Pliers
Toggle Nut 4pcs
Screw 4pcs
Wire Connector 1pcs
Auxiliary tool (not included)
1. FIXTURE PREPARATION: Remove clips from endcaps, then remove lens carefully to avoid damage, by pressing down on the lens at either end and slide it under the metal dimple in the fixture body. Lift up the lens from the opposite end and take it out of the fixture. To return back the lens, slide one end of lens into fixture under- neath the dimple. Insert opposite end into the fixture.Center lens between dimples, then push clips on each endcaps to protect lens following down.
2. FIXTURE WIRING: 1. Ground the fixture by connecting the ground wire (bare or green) to the green screw or ground wire provided in the housing. 2. Connect the black ballast lead to the (Line) by using a wire nut. Connect the white ballast lead to the (Neutral) by using a wire nut.
GlobaLux Lighting LLC ? 2037 S. Vineyard Ave. Ontario, CA 91761 ? 909-591-7605 Fax: 909-590-3220
1/2
RIS9414
LED Economic Wraparound Fixture Installation Instructions
SLIDE LENS UNDER DIMPLE IN FIXTURE BODY
CAUTION! PLASTIC LENS CAN BE BRITTLE. DO NOT OVER STRESS.
PUSH CLIPS ON EACH END TO PROTECT LENS
PUSH IN AND SLIDE UNDER DIMPLE
DIMPLE CLIP
FIXTURE MOUNTING:
Ceiling Joists
Outlet Box
Fixture Housing
Wood Screws Outlet Box
Fixture Housing Toggle Bolts
WIRING DIAGRAM:
+ LED Module
-
Black
+
L
-
Driver
White N
Ground Wire
(5) Luminaire Disconnect
Black
Black
White
120V~277V White SERVICE
Ground Wire WIRE CONNECTOR
SKETCH OF INSTALLATION HOLE DISTANCE:
INSTALLATION DIAGRAM:
GlobaLux Lighting LLC ? 2037 S. Vineyard Ave. Ontario, CA 91761 ? 909-591-7605 Fax: 909-590-3220
2/2
RIS9414
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- lew series installation instructions
- text description for pcpi especification clinical topic
- mixed fund baloise fund invest lux bfi progress eur
- cognitive status problem observation deprecated
- survey of alliances performance in sector
- ΤΕΧΝΙΚΕΣ ΠΡΟΔΙΑΓΡΑΦΕΣ
- hqmf templates for qdm december 2013
- 840 1 z bits 6 x 25 mm
- qdm december 2012 hqmf templates office of the national
- 3 90 reaction observation v2
Related searches
- xfinity free installation promo
- installation and operation qualification
- equipment installation qualification
- installation qualification template
- installation qualification requirements
- software installation qualification
- installation qualification wiki
- installation qualification checklist
- installation qualification protocol template
- installation qualification sop
- equipment installation qualification template
- installation qualification report