Chapter 3 - IBC (Status October 2012) - VCI
| | | |
| | |Chapter 3 IBC |
| | |Section 3.0 General information |
3.0.0 Contents
3.0 General information
3.0.0 Contents
3.0.1 Introduction
3.0.2 Application see German version
3.0.3 Quality requirements
3.0.4 Recovery systems
3.0.5 Basic conditions for the cession of lending packaging see German version
3.1 Rigid plastic-IBC
3.1.1.1 1000 L-Combined-IBC for liquids
3.2 Metal-IBC
3.2.1.1 1000 L-Metal-IBC for liquids, cubic
3.2.1.2 1000 L-Metal-IBC for dry bulk
3.2.1.3 1000 L-Metal-IBC for liquids, cylindrical
3.3 Flexible plastic-IBC
3.3.1 Flexible plastic-IBC with discharge spouts
3.3.2 Flexible plastic-IBC with apron
| | |Chapter 3 IBC |
| | |Section 3.0 General information |
3.0.1 Introduction
Packaging reduction in the chemical industry resulted to development of IBC for liquids and solids.
The concerned IBC include volumes from 450 to 3000 Litres.
Specifications for IBC produced from corrugated cardboard packaging/octagonal box are not listed in this chapter, because these are dependent e.g. on the particular application and on the basic dimensions of the used pallet. Information for corrugated cardboard
packaging is contained in chapter 6.
For materials and the manufacturing of packaging the EU- and national directives and
regulations are applied.
It is recommended the IBC listed of this chapter used largely for the following reasons:
Standardization
By use of standard containers low-cost and environment-relevant packaging solutions can be achieved.
Possibility of multiple used
For standardized IBC the possibility to recondition and thus to reuse is existing.
Conditions relevant to environment
Also legal interests have to be taken into consideration with the use of packaging
(packaging ordinance, dangerous goods transport).
| | | |
| | | |
| | |Chapter 3 IBC |
| | |Section 3.0 General information |
3.0.3 Quality requirements
Information on quality assurance can be taken from chapter 9.
| | | |
| | |Chapter 3 IBC |
| | |Section 3.0 General information |
3.0.4 Recovery systems
Depending on type of IBC there are different ways / organisations of recycling:
| |
|VDF - Verband der Deutschen Fassverwertungsbetriebe e.V. |
|RIGK - Gesellschaft zur Rückführung industrieller und gewerblicher Kunststoffverpackungen mbH |
The manufacturers of IBC offer services in Europe for reconditioning and further use.
More information can be taken from Chapter 10 (recovery systems).
| | | |
| | |Chapter 3 IBC |
| | |Section 3.1 Rigid plastic-IBC |
3.1.1.1 1000 L-Combined-IBC for liquids
| | | | | |
| | | |
|Dimensions in mm | |[pic] |
| | | |
|Length: 1200 | | |
| | | |
|Width: 1000 | | |
| | | |
|Height: 1160 | | |
| | | |
|Pallet fork entry: 100 | | |
| | | |
|Charge opening (nominal size): 150 or 225 | | |
|Discharge opening (nominal size): 50 or 80 | | |
|2 plates on opposite sides (width x height) | | |
|in front: 660 x 390 | | |
|at the back: 470 x 390 | | |
Nominal capacity: 1000 L
Brimful capacity: 1060 L
Material / container: PE, natural-coloured, UV-stabilized
frame: steel galvanized
pallet: steel galvanized, wood (ISPM 15), plastic or combinations of this materials
Technical requirements: 3-fold stackable (total weight min.1500 kg/IBC)
suitable for shelf stores
Residual emptying: according to VPA 4
Construction / container: exchangeable
charge opening: concentric on top, sealing capable
lid: with or without venting device
discharge: sealing capable, sealt with Al-foil, S 60 x 6 external thread (alternativly S 100 x 8 or Kamlok 2’’), concentric at the bottom of a width side
base plate: four way entry
Material identification: inner drum according to VerpackV § 14
Minimum requirements: packaging group II and approved for all standards liquids, free of surface active substances like e.g. silicones, surfactants, lubricants, greases
Approval marking: according to the valid transport regulations for dangerous good
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
| | | |
| | |Chapter 3 IBC |
| | |Section 3.2 Metal-IBC |
|3.2.1.1 1000 L-Metal-IBC for liquids, cubic | | |
| | | | | |
| | | |
|Dimensions in mm | |[pic] |
| | | |
|Length: 1200 | | |
| | | |
|Width: 1000 | | |
| | | |
|Height: 1650 max. | | |
| | | |
|Pallet fork entry: 100 min. | | |
| | | |
|Charge opening (nominal size): 457 max. | | |
| | | |
|2 plates on opposite sides (width x height) | | |
|in front: 660 x 390 | | |
|at the back: 470 x 390 | | |
Nominal capacity: 1000 L
Brimful capacity: 1060 L
Material / container: stainless steel according DIN EN 10088-2
frame: steel hot galvanized
Technical requirements: 3-fold stackable (total weight min.1500 kg/IBC), cranable,
suitable for shelf stores
Residual emptying: according to VPA 4
Construction / container: with electric static grounding
top: sealing capable opening with clamp ring
concentric on top, with sealing capable venting device
bottom: with 3" discharge, 2" or 3" valve, sealing capable
base plate: four way entry
Minimum requirements: approved for packaging group II, free of surface active
substances like e.g. silicones, surfactants, lubricants, greases
Approval marking: according to the valid transport regulations for dangerous goods
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
| | | |
| | |Chapter 3 IBC |
| | |Section 3.2 Metal-IBC |
|3.2.1.2 1000 L-Metal-IBC for dry bulk | | |
| | | | | |
|Dimensions in mm | | |
| | |[pic] |
|Length: 1200 | | |
| | | |
|Width: 1000 or 1200 | | |
| | | |
|Height: 1800 max. | | |
| | | |
|Pallet fork entry: 100 min. | | |
| | | |
|Charge opening (nominal size): 457 | | |
| | | |
|Butterfly valve (nominal size): 250 | | |
| | | |
|2 plates on opposite sides (width x height) | | |
|in front: 660 x 390 | | |
|at the back: 470 x 390 | | |
Nominal capacity: 1000 L
Brimful capacity: 1060 L
Material / container: stainless steel according DIN EN 10088-2
frame: steel hot galvanized
Technical requirements: 3-fold stackable (total weight min.1500 kg/IBC), cranable,
suitable for shelf stores
Residual emptying: according to VPA 4
Construction / container: with electric static grounding
top: opening with lid and clamp ring concentric on top, with
sealing capable venting device
bottom: funnel 45, with butterfly valve, sealing capable discharge,
as required fixture plate for vibrating equipment
base plate: four way entry
Minimum requirements: approved for packaging group II, free of surface active
substances like e.g. silicones, surfactants, lubricants,
greases
Approval marking: according to the valid transport regulations for dangerous goods
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
| | | |
| | |Chapter 3 IBC |
| | |Section 3.2 Metal-IBC |
|3.2.1.3 1000 L-Metal-IBC for liquids, cylindrical | | |
| | | |
|Dimensions in mm | | |
| | | |
|Length: 1200 (+0/-10) | | |
| | |[pic] |
|Width: 1100 (+0/-10) | | |
| | | |
|Height: 1670 (+0/-50) | | |
| | | |
|Diameter: 1080 (+0/-10) | | |
| | | |
|Pallet fork entry: 100 min. | | |
| | | |
|Charge opening (nominal size): 457 | | |
| | | |
|2 plates on opposite sides (width x height) | | |
|in front: 660 x 390 | | |
|at the back: 470 x 390 | | |
Nominal capacity: 1000 L
Brimful capacity: 1020 L
Material / container: Stainless steel according DIN EN 10088-2
surface quality B 3 according DIN EN 10163
frame: Steel hot galvanized
Technical requirements: 3-fold stackable (total weight min.1500 kg/IBC), cranable,
suitable for shelf stores
Residual emptying: according to VPA 4
Construction / container: with electric static grounding, 2 forks entry´s integrated in frame on both sides
top: opening with lid and clamp ring concentric on top,
sealing capable with plug R1", venting equipment R1"
bottom: ellipsoidal deep drawn calotte, clearance free loose flange DN80, container flap 3" with camlock and plug DN80,
sealing capable
base plate: four way entry
Minimum requirements: approved for packaging group II, free of surface active substances like e.g. silicones, surfactants, lubricants, greases
Approval marking: according to the valid transport regulations for dangerous goods
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
| | | |
| | |Chapter 3 IBC |
| | |Section 3.3 Flexible plastic-IBC |
|3.3.1 Flexible plastic-IBC with discharge spouts (following EN ISO 21898) | | |
| | | | | |
|Dimensions in mm | |[pic] |
| | | |
|Length, inside (b): 880 or 920 (±10) | | |
| | | |
|Width, inside (c): 880 or 920 (±10) | | |
| | | |
|Height, inside (a): as required (±20) | | |
| | | |
|Lenght of filling spout (i1): 550 (+50/-0) | | |
| | | |
|Diameter of filling spout (d1): 380 (±10) | | |
| | | |
|Length of discharge spout (i2): 550/850 (+50/-0) | | |
| | | |
|Diameter of discharge spout (d2): 380 (±10) | | |
| | | |
|Lifting strap / length (free length): 250 (±10) | | |
Nominal capacity: as required into dependence of height of container a
Colour: white (natural colour)
Material / body,bottom,
lid, filling-/discharge spout: PP-fabric tape if necessary coated with PP (at use of an
inliner a coating can be renounced)
lifting strap: PP
Technical requirements: nominal working load 500, 750, 1000, 1250 or 1500 kg ,
safety factor (SF) 5:1 (single trip) or 6:1 (dangerous goods) or 8:1 (multi trip), UV-stabilized
Residual emptying: according to VPA 4
Construction: according to EN ISO 21898, picture E.8, four-point-lifting with two point- or single point-fixing
document wraps DIN A4-format, transparent (for dangerous
goods on 2 opposite sides)
discharge closed (with fixed PP-band)
Material identification: according to VerpackV §14
Approval marking: according to the valid transport regulations for dangerous goods
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
| | | |
| | |Chapter 3 IBC |
| | |Section 3.3 Flexible plastic-IBC |
|Flexible plastic-IBC with apron (following EN ISO 21898) | | |
| | | | | |
|Dimensions in mm | | |
| | | |
|Length, inside (b): 880 or 920 (±10) | | |
| | | |
|Width, inside (c): 880 or 920 (±10) | | |
| | | |
|Height, inside (a): as required (±20) | | |
| | | |
|Length of apron (p): 850 (±20) | | |
| | | |
|Length of discharge spout (i2): 550/850 (+50/-0) | | |
| | | |
|Diameter of discharge spout [d2]: 380 (±10) | | |
| | | |
| | | |
|Lifting strap / length (free length): 250 (±10) | | |
Nominal capacity: as required into dependence of height of container a
Colour: white (natural colour)
Material / body, bottom,
apron and discharge spout: PP-fabric tape if necessary coated with PP (at use of an
inliner a coating can be renounced)
lifting strap: PP
Technical requirements: nominal working load 500, 750, 1000, 1250 or 1500 kg ,
safety factor (SF) 5:1 (single trip) or 6:1 (dangerous goods) or 8:1 (multi trip, UV-stabilized
Residual emptying: according to VPA 4
Construction: according to EN ISO 21898, picture E.8, four-point-lifting with (eligible) two point- or single point-fixing document wraps DIN A4-format, transparent (for dangerous goods on 2 opposites sides)
discharge closed (with fixed PP-band)
Material identification: according to VerpackV §14
Approval marking: according to the valid transport regulations for dangerous goods
Standard recommendation without obligation. Issued by Verband der Chemischen Industrie e.V.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- 2012 ibc draft chapter 10
- 2012 ibc draft capter 7
- statement of structural tests and special inspections stsi
- recommended amendments to the
- commercial building code 00030604 rtf city of west
- chapter 3 ibc status october 2012 vci
- recommended amendments to the 2012 international
- florida building
- chapter 1 general information south carolina
Related searches
- chapter 3 developmental psychology quizlet
- mcgraw hill algebra1 chapter 3 lesson 8
- chapter 3 psychology quizlet test
- psychology chapter 3 quiz answers
- developmental psychology chapter 3 quizlet
- strategic management chapter 3 quizlet
- psychology chapter 3 exam
- psychology chapter 3 test questions
- quizlet psychology chapter 3 quiz
- chapter 3 psychology quiz
- developmental psychology chapter 3 test
- quizlet psychology chapter 3 answers