SKELETON - ETSI



ETSI TR 103 593 V0.0.24 (2019-07)System Reference Document (SRDoc);Transmission characteristics;Technical characteristics for radiodetermination equipment for vehicular applications within the frequency range 77 GHz - 81 GHzsymbol 60 \f "Wingdings" \s 16<TECHNICAL REPORTReferenceDTR/ERM-576KeywordsRadio, SRDocETSI650 Route des LuciolesF-06921 Sophia Antipolis Cedex - FRANCETel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-préfecture de Grasse (06) N° 7803/88Important noticeThe present document can be downloaded from: present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at you find errors in the present document, please send your comment to one of the following services: NotificationNo part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI.The content of the PDF version shall not be modified without the written authorization of ETSI.The copyright and the foregoing restriction extend to reproduction in all media.? ETSI yyyy.All rights reserved.DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.3GPPTM and LTE? are trademarks of ETSI registered for the benefit of its Members andof the 3GPP Organizational Partners.oneM2M logo is protected for the benefit of its Members.GSM? and the GSM logo are trademarks registered and owned by the GSM Association.Contents TOC \o \w "1-9"Intellectual Property Rights PAGEREF _Toc13748735 \h 5Foreword PAGEREF _Toc13748736 \h 5Modal verbs terminology PAGEREF _Toc13748737 \h 5Executive summary PAGEREF _Toc13748738 \h 5Introduction PAGEREF _Toc13748739 \h 51Scope PAGEREF _Toc13748740 \h 62References PAGEREF _Toc13748741 \h 62.1Normative references PAGEREF _Toc13748742 \h 62.2Informative references PAGEREF _Toc13748743 \h 63Definitions, symbols and abbreviations PAGEREF _Toc13748744 \h 93.1Definitions PAGEREF _Toc13748745 \h 93.2Symbols PAGEREF _Toc13748746 \h 103.3Abbreviations PAGEREF _Toc13748747 \h 104Comments on the System Reference Document PAGEREF _Toc13748748 \h 104.1User defined subdivisions of clause(s) from here onwards PAGEREF _Toc13748749 \h 105Presentation of system and technology PAGEREF _Toc13748750 \h 105.1Background on current technology PAGEREF _Toc13748751 \h 105.2Description of future technology PAGEREF _Toc13748752 \h 126Market information PAGEREF _Toc13748753 \h 167Technical information PAGEREF _Toc13748754 \h 187.1Detailed technical description PAGEREF _Toc13748755 \h 187.1.1Required Tx bandwidth and Tx power for sensor use categories PAGEREF _Toc13748756 \h 187.1.2mm-wave technology PAGEREF _Toc13748757 \h 217.1.3Interference Mitigation techniques PAGEREF _Toc13748758 \h 217.1.4Influence of the bumper fascia PAGEREF _Toc13748759 \h 217.2Status of technical parameters PAGEREF _Toc13748760 \h 267.2.1Current ITU and European common allocations PAGEREF _Toc13748761 \h 267.2.2Sharing and compatibility studies already available PAGEREF _Toc13748762 \h 277.3Information on relevant standards PAGEREF _Toc13748763 \h 298Radio spectrum request and justification PAGEREF _Toc13748764 \h 319Regulation PAGEREF _Toc13748765 \h 339.1Current regulation PAGEREF _Toc13748766 \h 349.2Proposed regulation PAGEREF _Toc13748767 \h 34Annex A: Overview of current and future use cases PAGEREF _Toc13748768 \h 37A.1 Advanced Driving Assistance Systems: descriptions of features & use cases PAGEREF _Toc13748769 \h 37A1.1 Adaptive Light Control PAGEREF _Toc13748770 \h 37A1.2Forward Collision Warning PAGEREF _Toc13748771 \h 37A1.3Automatic Emergency Braking PAGEREF _Toc13748772 \h 38A1.4Automatic Cruise Control (ACC) PAGEREF _Toc13748773 \h 39A1.5Traffic Sign Recognition / Intelligent Speed Control PAGEREF _Toc13748774 \h 39A1.6Enhanced Blind Spot Monitoring PAGEREF _Toc13748775 \h 40A1.7Lane Keep Assist PAGEREF _Toc13748776 \h 40A1.8Lane Change Assist PAGEREF _Toc13748777 \h 41A1.9Traffic Jam Assist PAGEREF _Toc13748778 \h 41A1.10Rear Cross Traffic Alert PAGEREF _Toc13748779 \h 42A1.11Front Junction-Intersection Assist PAGEREF _Toc13748780 \h 44A1.12Highway Chauffer PAGEREF _Toc13748781 \h 44A1.13Rear – Auto Emergency Braking PAGEREF _Toc13748782 \h 45A1.14Automatic Lane Change PAGEREF _Toc13748783 \h 46A1.15Automated Parking Assist (APA) PAGEREF _Toc13748784 \h 46A1.16Home Zone Automated Parking (HZAP) PAGEREF _Toc13748785 \h 47A1.17Valet Parking PAGEREF _Toc13748786 \h 48A1.18Highway Pilot PAGEREF _Toc13748787 \h 48A.2 Advanced Driving Assistance Systems for other kind of ground based vehicles: descriptions of features & use cases PAGEREF _Toc13748788 \h 49A2.1General PAGEREF _Toc13748789 \h 49A2.2Trains (locomotive and train cars,…) PAGEREF _Toc13748790 \h 50A2.3Tram/Metro PAGEREF _Toc13748791 \h 52A2.4Construction / farming vehicles (outdoor) PAGEREF _Toc13748792 \h 53A2.5Industrial vehicles / Material handling (indoor/outdoor) PAGEREF _Toc13748793 \h 54A.3Vehicle safety programmes PAGEREF _Toc13748794 \h 56A3.1Vehicle safety programmes PAGEREF _Toc13748795 \h 56A3.2New Car Assessment Programs (NCAP) PAGEREF _Toc13748796 \h 56A3.3EU NCAP PAGEREF _Toc13748797 \h 56A3.4US NCAP PAGEREF _Toc13748798 \h 57A3.5Future autonomous driving vehicles PAGEREF _Toc13748799 \h 58Annex B: summary of Regulations in selected countries for 76-77 GHz and 77 - 81 GHz radar sensors PAGEREF _Toc13748800 \h 60Annex C Radar Basics PAGEREF _Toc13748801 \h 63C.1Maximum range PAGEREF _Toc13748802 \h 63C.2Definition of sensor performance parameters PAGEREF _Toc13748803 \h 65C.3SNR PAGEREF _Toc13748804 \h 66C.4Antenna properties PAGEREF _Toc13748805 \h 66Annex : Change History PAGEREF _Toc13748806 \h 68History PAGEREF _Toc13748807 \h 69Intellectual Property RightsEssential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI?SR?000?314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server ().Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI?SR?000?314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document.TrademarksThe present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.ForewordThis Technical Report (TR) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM) .Modal verbs terminologyIn the present document "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions)."must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.Executive summaryIntroductionEditors note: consider if required , otherwise skip 1ScopeNote Frank will revise the section The present document describes radio determination equipment for vehicular applications within the frequency range 77 GHz - 81 GHz which may require a change of the present frequency designation / utilization within the EU/CEPT.This document is limited to Ground based vehicular applications. Editorsnote : align with new proposal in chapter 9 , use text from other SRDoc (LPR TR 103595)This document provides information on the existing and intended applications, the technical parameters, the relation to the existing spectrum regulation (ECC/DEC(04)03 and 2004/545/EC) and it reflects the WRC -2015 decision (RR footnote 5.559B and ITU-R recommendation M.2057 and ITU-R report M.2322) on automotive ground-based radar). The current regulation should be reviewed in the light of the results of WRC - 2015.The WRC 2015 decision refers to ground-based radar applications, including automotive radars. The presentis document is limited to Ground based vehicular applications. It includes in particular:Market informationTechnical information including expected sharing and compatibility issues Regulatory issues.2References2.1Normative referencesNormative references are not applicable in the present document.2.2Informative referencesReferences are either specific (identified by date of publication and/or edition number or version number) or nonspecific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies.NOTE:While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity.The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area.[i.1] ERC/REC 70-03, Relating to the use of Short Range Devices (SRD), 22 May 2018[i.2]Commission Implementing Decision (EU) 2017/1483 of 8 August 2017 amending Decision 2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing Decision 2006/804/EC[i.3] ERC Report 003Harmonisation of frequency bands to be designated for road transport information systems, Lisbon, February 1991[i.4]ERC/DEC/(92)02 ERC Decision of 22 October 1992 on the frequency bands to be designated for the coordinated introduction of Road Transport Telematic Systems (ERC/DEC/(92)02) Note: document is withdrawn [i.5]ECC Decision of 15 March 2002 on the frequency bands to be designated for the co-ordinated introduction of Road Transport and Traffic Telematic Systems (ECC/DEC/(02)01) Note: document is withdrawn[i.6] ETSI TR 101 982 V1.2.1 (2002-07), Radio equipment to be used in the 24 GHz band; System Reference Document for automotive collision warning Short Range Radar[i.7]ECC Report 23, Compatibility of automotive collision warning Short Range Radar operating at 24 GHz with FS, EESS and Radio Astronomy, Cavtat, May 2003[i.8] ETSI TR 102 263 V1.1.2 (2004-02), Road Transport and Traffic Telematics (RTTT); Radio equipment to be used in the 77 GHz to 81 GHz band; System Reference Document for automotive collision warning Short Range Radar[i.9] ECC Report 56, Compatibility of automotive collision warning short range radar operating at 79 GHz with radio communication services, Stockholm, October 2004[i.10]ECC/DEC(04)03, The frequency band 77-81 GHz to be designated for the use of Automotive Short Range Radars, Approved 19 March 2004, Corrected 6 March 2015[i.11]EC Decision 2004/545/EC, Commission Decision of 8 July 2004 on the harmonisation of radio spectrum in the 79 GHz range for the use of automotive short-range radar equipment in the Community[i.12]ECC/DEC(04)10, ECC Decision of 12 November 2004 amended 01 June 2012 on the frequency bands to be designated for the temporary introduction of Automotive Short Range Radars (SRR)[i.13]COMMISSION IMPLEMENTING DECISION (EU) 2017/2077 of 10 November 2017 amending Decision 2005/50/EC on the harmonisation of the 24 GHz range radio spectrum band for the time-limited use by automotive short-range radar equipment in the Community[i.14] ETSI TR 102 664 V1.2.1 (2010-04), Road Transport and Traffic Telematics (RTTT); Short range radar to be used in the 24 GHz to 27,5 GHz band; System Reference Document[i.15]ECC Report 158, The impact of 26 GHz SRR applications using ultra-wideband (UWB) technology on radio services, Cardiff, January 2011[i.16] ETSI EN 301 091-1 V2.1.1 (2017-01), Radar equipment operating in the 76 GHz to 77 GHz range; harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Part 1: Ground based vehicular radar[i.17]ETSI EN 302 264 V2.1.1 (2017-05), Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU[i.18]?H. Meinel: Automotive Radar – History, state-of-the-art and future trends, EuRAD 2012.[i.19]Texas Instruments: AWR1243, 76-to-81 GHz High Performance Automotive MMIC, [i.20]F. Pfeiffer: Analyse und Optimierung von Radomen für automobile Radarsensoren, Dissertation 2009 (in German)[i.21]ITU Radio Regulations, edition of 2016 [i.22]Recommendation ITU-R M.2057-1 (01/2018) Systems characteristics of automotive radars operating in the frequency band 76 - 81 GHz for intelligent transport systems applications[i.23]European Commission 2018/0145[COD]: Proposal for a Regulation of the European Parliament and of the Council on type-approval requirements for motor vehicles and their trailers, and systems, components and separate technical units intended for such vehicles, as regards their general safety and the protection of vehicle occupants and vulnerable road users, amending Regulation (EU) 2018/… and repealing Regulations (EC) No 78/2009, (EC) No 79/2009 and (EC) no 661/2009 (Text with EEA relevance) {SEC(2018)270 final} – {SWD(2018) 190 final} – {SWD(2018)191 final}[i.24]European Commission: Benefit and Feasibility of a Range of New Technologies and Unregulated Measures in the fields of Vehicle Occupant Safety and Protection of Vulnerable Road Users (March 2015)[i.25]Department Of Transportation, National Highway Traffic Safety Administration, [Docket No. NHTSA-2015-0119], New Car Assessment Program (NCAP)[i.26]Report ITU-R M.2322-0 (11/2014) Systems characteristics and compatibility of automotive radars operating in the frequency band 77.5 - 78 GHz for sharing studies.[i.27]DAT Report 2016, DAT Group, [i.28][i.29]MOSARIM documentsMOSARIM webpage no longer available (03/2019). CORDIS factsheet of the project is available [i.30]NTHSA Radar congestion study [i.31]SAE website: automated driving levels [i.32]Report: Measurements of Automotive Radar Emissions received by a Radio Astronomy Observatory –Kitt Peak Measurements [i.33]IEEE paper: Reduced Interference of 79GHz UWB Automotive Radars to Radio Astronomy Stations by Signal Integration Effects[i.34]IMIKO public funded project website (german only) HYPERLINK "" [i.35]Cedric Malaquin, The Automotive Radar Market, Workshop WW-02, EuRAD 2018[i.36]ISO 22178:2009: Intelligent transport systems -- Low speed following (LSF) systems -- Performance requirements and test procedures[i.37]ISO 22839:2013: Intelligent transport systems -- Forward vehicle collision mitigation systems -- Operation, performance, and verification requirements[i.38]ISO 16787:2017: Intelligent transport systems -- Assisted parking system (APS) -- Performance requirements and test procedures[i.39]ISO 19237:2017: Intelligent transport systems -- Pedestrian detection and collision mitigation systems (PDCMS) -- Performance requirements and test procedures[i.40]ISO/FDIS 20900: Intelligent transport systems -- Partially automated parking systems (PAPS) -- Performance requirements and test procedures[i.41]ISO/CD 21202: Intelligent transport systems -- Partially Automated Lane Change Systems (PALS) -- Functional / operational requirements and test procedures[i.42]UNECE Proposal for technical requirements for an automated lane keeping system [UNECE_ALKS][i.43]UNECE Automatic lane change following a request by the driver [UNECE_ACSF_ESF][i.44]ETSI EN 305 550 V2.1.0 (2017-10), Short Range Devices (SRD); Radio equipment to be used in the 40 GHz to 246 GHz frequency range[i.45]ETSI EN 302 372 V.2.1.1 (2016-10), Short Range Devices (SRD); Tank Level Probing Radar (TLPR) equipment operating in the frequency ranges 4,5?GHz to 7?GHz, 8,5?GHz to 10,6?GHz, 24,05?GHz to 27?GHz, 57?GHz to 64?GHz, 75?GHz to 85 GHz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU[i.46]ETSI EN 302 729 V2.1.1 (2016-10), Short Range Devices (SRD); Level Probing Radar (LPR) equipment operating in the frequency ranges 6?GHz to 8,5?GHz, 24,05?GHz to 26,5?GHz, 57?GHz to 64?GHz, 75?GHz to 85?GHz; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU[i.47]ETSI EN 301 783 V2.1.1 (2016-01), commercially available amateur radio equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU[i.48]ETSI EN 303 360 V1.1.1 (2017-02); Short Range Devices; Transport and Traffic Telematics (TTT); Radar equipment operating in the 76 GHz to 77 GHz range; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Obstacle Detection Radars for Use on Manned Rotorcraft [i.49]ETSI EN 301 091-2 V2.1.1 (2017-01); Short Range Devices; Transport and Traffic Telematics (TTT); Radar equipment operating in the 76 GHz to 77 GHz range; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Part 2: Fixed infrastructure radar equipment [i.50]ETSI EN 301 091–3 V1.1.1.(2017-02); Short Range Devices; Transport and Traffic Telematics (TTT); Radar equipment operating in the 76 GHz to 77 GHz range; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU; Part 3: Railway/Road Crossings obstacle detection system applications[i.51]ETSI EN 302 217 V3.0.8) (2016-06); Fixed Radio Systems; Characteristics and requirements for point-to-point equipment and antennas; Part 2: Digital systems operating in frequency bands from 1,3 GHz to 86 GHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU [i.52][i.53][i.54][i.55]Cross Section Measurements of Pedestrian Dummies and Humans in the 24/77 GHz Frequency Bands "Joaquim Fortuny-Guasch, Jean-Marc Radar Chareau", section 3.2)ISPRA studie[i.56]ISO 15622:2018: Intelligent transport systems -- Adaptive cruise control systems -- Performance requirements and test procedures, given radar cross secrtions [10 m2] for vehicle [3m2] for motor bikes, but for motor bike due to variation based on observation angle a realistic value for worst case scenarios for front looking approaching motor bike is given by a value of [1m2].3Definitions, symbols and abbreviations3.1DefinitionsFor the purposes of the present document, the [following] terms and definitions [given in ... and the following] apply:3.2SymbolsrDielectric constantΧeDielectric susceptibility: r -13.3AbbreviationsFor the purposes of the present document, the [following] abbreviations [given in ... and the following] apply:AEBAutomatic Emergency BrakingNCAPNew Car Assessment ProgramEuro NCAP European New Car Assessment Program US NCAPUS New Car Assessment ProgramNHTSANational Highway Transportation Safety Administration (USA)FCWForward Collision WarningLDWLane Departure WarningLKSLane Keeping-Assist SystemRRITU-R Radio Regulations VRU-AEBVulnerable Roadway User – Automatic Emergency Braking (pedestrians & bicyclists)Ultra short range radar Short range radar Mid range radar Long range radarHADHighly Automated Driving4Comments on the System Reference Document 4.1User defined subdivisions of clause(s) from here onwards 5Presentation of system and technology Note: Thomas will check consistency until next drafting session 5.1Background on current technologyRadar sensors for supporting the driver of a vehicle have been under development by companies in Europe, the United States and Asia for several decades [i.18]. Early prototypes were operated in various frequency ranges such as 10 GHz, 16 GHz, 24 GHz, 35 GHz, 50 GHz or 94 GHz.Then, in 1996, the first series busses and trucks were equipped in the United States with front and side looking collision warning radars, operating at approximately 10 GHz and 24 GHz.A few years later, the first series cars were equipped with front looking radars for adaptive cruise control, operating in the band 76-77 GHz, rear corner radars for parking support and blind spot detection, operating in the 24 GHz ultra-wideband range rear corner radars for blind spot detection and lane change assistance, operating in the 24 GHz narrow band range.Since then, advances in RF circuit integration, advances in microcontroller performance and advances in software algorithms helped to further improve the sensor performance, to add additional assistance functions and to reduce the sensor price so that today millions of 24 GHz (narrow band) and 76-77 GHz radar sensors per year are installed in new vehicles, ranging from small city cars up to luxury cars, thus supporting more and more drivers in safer driving.It should be noted, that due to a change in regulation in Europe automotive radars in 24.25 GHz – 26.65 GHz (UWB ) will be phased out by 2020 [i.12] Since this band is one of the 5G pioneer bands, it is expected that all other administrations following implementation of IMT-2020, will phase out regulation for UWB automotive radars in the near future. Tab. 1 gives an overview of current use cases.Frequency rangeMounting position in vehicleClassificationNon-exhaustive list of typical Use-cases24.05 GHz – 24.25 GHzFrontMRRDistance warningRear cornersMRRBlind-spot detection, lane change assistance, rear cross traffic alert, precrash rear, exit assistance24.25 GHz – 26.65 GHz (UWB)Will be Phased out in Europe by 2022FrontSRR-69500741349Use consistent terms as in Annex A0Use consistent terms as in Annex AStop-and-goRear cornersSRRBlind-spot detection, lane change assistance, rear cross traffic alert, precrash rear, exit assistance76.00 GHz – 77.00 GHzFrontLRRAdaptive cruise controlFront cornersMRRFront cross traffic alertRear cornersMRRBlind-spot detection, lane change assistance, rear cross traffic alert, precrash rear, exit assistance77-81GHzFill fillList of use case are missing Up to now (02/2019), only 2 products received equipment type approval in the US Tab. 1: Overview of radar sensors and use cases in current vehicles.Remarks: The regulation for 24GHz UWB radar sensors are time limited to 2022. The functions that are currently provided by 24GHz UWB radar sensors are envisaged to be implemented in 79GHz sensors.The regulation of 24GHz NB and 76GHz radar sensors are not time limited and will see continued use in the future.The fast development which took place over time lead to some inconsistency in naming and the usage of terms with regards to automotive radar categories: In some documents all automotive radars are called “short range radars (SRR)” because the maximum measurement range of up to approx.. 250 m is short compared to several kilometers for other radars used for example by airplanes or ships. Documents dealing specifically with automotive radars use the terms to describe certain categories based on the function and application of the auto radar sensor. Typically 3 categories of automotive radar sensors are described. The exact value for the measurement range of a category is not consistent and depends on each document. It should be noted that to ensure stable function in the given measurement range of a sensor, the RF-coverage range of the device must be larger. Typical values for the 3 categories are “short range radar (SRR)” only for devices with a maximum measurement range of up to approx. 30 m, while devices with up to 150 m are called “mid-range radar (MRR)” and devices up to 250m are called “long range radar (LRR)”.In parallel, over time ISO worked on standardisation of assistance functions (see Tab.2). Certain functions defined by ISO can only be supported or provided by radar technology only.ISO-StandardsSummary of ContentISO 22178:2009: Intelligent transport systems -- Low speed following (LSF) systems -- Performance requirements and test procedures [i.36]The ISO standard covers functions and test method of a low speed following system, to control vehicle speed adaptively to a forward vehicle by using information like ranging and motion.. ISO 22839:2013: Intelligent transport systems -- Forward vehicle collision mitigation systems -- Operation, performance, and verification requirements [i.37]The ISO Standard covers functions and test method regarding Forward Vehicle Collision Mitigation Systems, to be able to reduce the severity of forward vehicle collisions that cannot be avoided, including the likelihood of forward collision with forward vehicles might be reduced.ISO 16787:2017: Intelligent transport systems -- Assisted parking system (APS) -- Performance requirements and test procedures [i.38]This document for Assisted Parking System (APS) addresses light-duty vehicles with such APS. The document establishes minimum functionality requirements regarding detection of suitable parking spaces, calculation of trajectories and lateral control of the vehicle. Also, Information regarding relevant obstacles in the driving path can also be included in the functionality. ISO 19237:2017: Intelligent transport systems -- Pedestrian detection and collision mitigation systems (PDCMS) -- Performance requirements and test procedures [i.39]The ISO standard describes requirements and test methods regarding Pedestrian Detection and Collision Mitigation Systems (PDCMS) to reduce the severity of pedestrian collisions that cannot be avoided. Target is to reduce the likelihood of fatality. Parameters like range and motion of pedestrian and / or subject vehicle is defined to derived commands and warnings for the driver.Tab. 2: Examples of ISO standards for current driver assistance systems.In parallel, over time the radio regulation for automotive radars has been developed in Europe Starting with 24 GHz narrowband (see [i.1], [i.2], which has been available for a long time as a ISM band, followed by 76-77 GHz between 1991 and 2002 (see [i.3], [i.4], [i.5]), 24 GHz Ultra-wideband between 2002 and 2011 (see [i.6], [i.7], [i.12], [i.13], [i.14], [i.15]) and finally 79 GHz ultra-wideband in 2004 (see [i.8], [i.9], [i.10], [i.11],It should be noted that some of the above referenced documents have been withdrawn in the meantime and they are listed here to provide a full picture of the development over the years.5.2Description of future technology Development roadmaps foresee further price/performance improvements of a single sensor allowing also new use cases and thus further improvement of road traffic safety (see Fig. 1 and Annex A)..025844500Fig. 1: Examples of current and future assistance functions with their coverage areas.Editors note: Magna to provide a fresh picture in better quality Editors note check abbreviations , put them in clause 3.3In part the growth is motivated by governments setting mandatory requirements for car manufacturers to include features like AEB (Automatic Emergency Breaking, Pedestrian Detection (VRU-AEB), or product rating agencies like Euro NCAP assigning higher ratings if safety functions are available as optional or standard equipment. (see [i.23], [i.24], [i.25]). Figure 2 gives an overview of already implemented and future safety functions initiated by different organisations / authorities in different countries. Figure 2 provides an overview of already implemented and future safety functions.Recently, the European Commission has issued a proposal [i.23] for the mandatory inclusion of multiple ADAS technologies The current proposal addresses the main problem of persistent high number of road accidents that in turn leads to a high number of fatalities and severe injuries and provides measures to increase safety at vehicle level so as to either avoid and lower the number of accidents or lower the severity of un-avoided accidents to limit the number of fatalities and severe injuries. [i.24]Editors note: Helmut to check if this is a direct quote from [i.24]Figure 3: European Commission views on the need for regulatory actionThe European Commission is proposing that within 3 years all new models introduced on the market must have 11 advanced safety features, such as:Advanced emergency brakingAlcohol interlock installation facilitation (cars, vans, trucks, buses)Drowsiness and attention detection (cars, vans, trucks, buses)o??? Distraction recognition / prevention (cars, vans, trucks, buses)o??? Event (accident) data recorder (cars and vans)o??? Emergency stop signal (cars, vans, trucks, buses)o??? Intelligent speed assistance (cars, vans, trucks, buses)o??? Lane keeping assist (cars, vans)o?? Reversing camera or detection system (cars, vans, trucks, buses) Further measures are proposed to be added a few years later. Through fusion of several such radar sensors and other environment perception sensors a sensing performance is on the horizon, powerful enough for automated driving. Following a proposal by SAE (society of automotive engineers), the introduction of autonomous vehicles is planned to be realized in five levels (see Fig. 4) .Editors note : there is a later version of the document dated 201806Also in 2016, SAE updated its classification, called J3016_201609Editors note: clarify the status of the SAE levels. What is the status of the source document? Figure 4: Five levels towards autonomous driving as proposed by SAE J3016 reference.Editors note: clarify if the latest version of the document contains different definitions for the levels Additional information and the figure is available in [i.31] Highly automated autonomous driving level 4 and fully automated cars of level 5 are expected to provide new forms and modes of transportation, changing the way mobility is provided.End of 2018, the first robotic taxi service was started by Waymo in Phoenix (Arizona) and additional services are under development world-wide. To ensure safety in highly automated vehicles and fully automated vehicles, multiple technologies will be required to perceive and access the driving environment. High robustness will be critical to providing safe & reliable transportation. New mobility services such as shared ownership and ride sharing will increase the actual usage time of devices included on these platforms due to higher utilization. UNECE and ISO are already working on respective regulations and standards (see examples in Tab. 3).ISO/FDIS 20900: Intelligent transport systems -- Partially automated parking systems (PAPS) -- Performance requirements and test procedures [i.40]ISO/CD 21202: Intelligent transport systems -- Partially Automated Lane Change Systems (PALS) -- Functional / operational requirements and test procedures [i.41]UNECE Proposal for Technical Requirements for an Automated Lane Keeping System [UNECE_ALKS] [i.42]UNECE Automatic lane change following a request by the driver, Informal Working Group on Automatically Commanded Steering Functions [UNECE_ACSF_ESF] [i.43]Tab. 3: Examples of regulations and standards under development for more automated driving.In clause 6, estimated numbers are given for the expected radar sensor growth.In clause 7 it is shown that to realize those new functions, the current regulation for the band 77 GHz – 81 GHz needs to be updated.6Market informationGerman DAT report shows for 2016 that 11 percent of German drivers buying a new car chose an ACC radar system (meaning a radar sensor at the vehicle front) and 9 percent chose a lane-change-assist radar system (meaning two radar sensors at the vehicle back) [i.27].Because of the drivers described in clause 5, the number of vehicles with radar sensors and the number of radar sensors per vehicle will increase (see Table XX and YY).Figure 5: levels of autonomous driving and required number of automotive radar sensors per vehicle and realized functions. [i.35]Level 0Level 1Level 2 Level 3 Level 4Level 5202521%33%32%10%3%1%20303%24%22%21%23%7% [Magna] gives a distribution of the different levels of automated driving versus time as given in table XXTable XXThat also means an increase in the total radar sensor value with a growing portion to 79 GHz radars (see Table YY)Introductory text for table YY required..Radar module forecast in $M, according to material from [i.35]yearModule value ($M)2016Approx.. 20002017300020184500201955002020Approx. 60002021Apporx. 700020227500Table YYAccording to company “Prescient & Strategic Intelligence”, the global automotive radar market had a size of approx. 3 billion US$ in 2017 “and is expected to witness a CAGR (cumulative annual growth rate ) of 21 %” [i.52].According to company “Research and Markets”, the global automotive radar market will reach a volume of approx.. 12 billion US$ is 2025 [i.28].The same result is also obtained by company “Grand View Research” [i.53].More cautious are the estimations of company “Transparency Market Research” who give a value of around 4.9 billion US$ in 2026 [i.54].7Technical information7.1Detailed technical description 7.1.1Required Tx bandwidth and Tx power for sensor use categoriesThe provided estimations of the required bandwidth and transmit power in table 2 are for current- and in table 3 for current and future use cases.The future requirements for radar based functions will increase, because more automated driving means less driver attention meaning new or higher sensor requirements with respect to detection range (give vehicle enough time to compute a vehicle reaction) and resolution of objects (now also debris on the road has to be detected and reacted on) . Therefore, the values given in the Table A illustrate how based on the new proposal regarding increase in power spectral density limits the performance of the sensor function based on category level will increase. Results calculated based on the current regulation and the target regulation are listed and can be compared.Radar use casesExample applicationsTypical Modulation bandwidthCurrent Power spectral density (current mean e.i.r.p)Requested Power spectral density (requested Mean e.i.r.p.)Current Regulation (typical detection range)Requested Regulation (typical detection range)Ultra short range Parking support3 GHz- 16 dBm/MHz(19 dBm)No changePossible, parking pole at 1 mNo changeShort range Blind spot detection800 MHz-9 dBm/MHz*(20 dBm)*-3 dBm/MHz (26 dBm)Small Child at 14 mPedestrian at 17m Bicycle at 22 mSmall Child at 20 mPedestrian at 23 mBicycle at 31 mMid range Lane change assist450 MHz-9 dBm/MHz*(16 dBm)*10 dBm/MHz (35 dBm) Small Child at 15m ***Pedestrian at 18 m ***Bicycle at 23 mMotor cycle at 31m *** Car at 56 m ***Small Child at 44mPedestrian at 58 mBicycle at at 69 mMotor cycle at 94m Car at 166 m Long range Adaptive cruise control250 MHz-9 dBm/MHz*(13 dBm)*20 dBm/MHz (40 dBm)** Motor cycle at 35 m***Car at 62 m ***Motor cycle at 166m Car at 296 m Table A: Resulting Detection performance increase comparing current regulation to the target regulation *) current regulation limit considering bumper loss requirement**) the calculated value is 43dBm for 250 MHz, but limited to 40 dBm based on regulation proposal Example: relationship between power spectral density (PSD dBm/MHz), bandwidth [BW] and EIPR [dBm] is calculated by EIRP = PSD+10*log (BW); ***) radar sensors following the current regulation cannot meet todays and future requirements regarding detection range for the given objects. Example: UNECE requests that in an automated lane keeping system a motorcycle must be detected in a minimum distance of 46mSummary: A significant increase in performance can be seen based on the given used cases, when comparing current to the proposed regulation. This will significantly increase the detection range for vulnerable road users, like childs / pedestrians, bicycle riders and (motor) cycle drivers.This also shows the current regulation is only providing limited number of used cases considering the large 4 GHz spectrum provided. The current regulation limits the used cases to parking and a blind spot detection with limited function. The change in regulation will therefore exploding the full spectrum capacity and use the spectrum efficiently, allowing the use of the spectrum for different and various applications regarding the related frequency band. Therefore, higher Power spectral density is required in 79 GHz band.7.1.2mm-wave technologyIntegrated mm-wave technology has evolved since the making available of the band in Europe in 2004.Because of progress in semiconductor technology, active components evolved from discrete RF transistors and diodes over GaAs-based oscillator, amplifier and mixer MMICs over SiGe-based transceiver MMICs to CMOS-based radar system chips (RSCs). Today several semiconductor manufacturers, offer highly integrated RSCs covering the frequency ranges 76 GHz – 77 GHz and 77 GHz – 81 GHz with very similar fundamental RF properties, for example [i.19]:Typical key parameters meters of such chipsets are Transmitter output power typ. 12 dBm (76 – 81 GHz)Receiver noise figure typ. 15 dB (76 - 77 GHz), typ. 16 dB (77 - 81 GHz).Because of progress in simulation tools and materials, antennas evolved in bandwidth and general performance.It is concluded that bandwidth and power levels as given in Table 3 are achievable.7.1.3Interference Mitigation techniques With an increasing number of radar sensors on the roads, the avoidance of interference becomes more and more challenging. During the last years, Mutual interference between automotive radars was described in various publications.Analysing and developing counter measures against mutual interference is becoming an important topic over the years. Resulting from this consideration, the automotive industry set up MOSARIM (MOre Safety for All by Radar Interference Mitigation). MOSARIM was set up as a public funded project under the EU FP 7 framework Thisthis project went 3 years from 2010-2012 with participation of OEMs and automotive radar sensor manufactures. The project proposed countermeasures and mitigation techniques in 6 different domains. The full details for the measures in each domain can be found in the MOSARIM reports. [i.29]Example approaches to handling interference are:adapting the timing of a sensor (limited by period after which the car needs an update from the sensor on the environmental situation, typically 40 – 100ms)adapting the frequency range used by a sensor (limited by frequency regulation).repairing disturbed receive signals in processing after digitization.Random timing Coded signals Some of the proposed countermeasures and mitigation techniques are implemented in current sensors, while other techniques do need further evaluation and development before they could be implemented in commercial available sensorsSeveral entities continue to study the mutual interference between automotive radars. In 12/2018 NTHSA published a study analysing the interference situation between automotive radars and proposes mitigation techniques building and developing further approaches from the MOSARIM project. [i.30]. However, analysis of the approach taken in this study show, that the used models were too simplistic and therefore the obtained results were too negative. In 2018 OEMs and Sensor manufacturers concluded that there is a need for further studies and further development of the MOSARIM results. This lead to the creation of a new public funded project. This project is funded by the German Federal Ministry of Education and Research (BMBF). The project name is IMIKO and it was started in 11/2018 and will run until 10/2021 [i.34].7.1.4Influence of the bumper fasciaThe bumper fascia is the plastic structure attached to the front and rear of a vehicle. The fascia may or may not be painted. The presence and the design of the fascia is dictated by the vehicle manufacturer, not by the sensor manufacturer.An advantage of radar sensors against other automotive environmental sensors is that they can be installed behind the bumper fascia, invisible from the outside. This makes it possible to install these sensors virtually everywhere on the vehicle allowing for 360 degrees detection.Develop line of argumentation given that the real starting point of the discussion is -9dBm since this appears to be the basis for the RAS interference studies and not -3dBm/MHz . This potentially makes discussion of facia loss irrelevant to requesting the change (reference to the request in chapter 9) General description of transmission absorption reflection of the radar signal due to a fascia. Figure 8: Illustration of radiated power splitting up into three components during interaction with bumper fasica (source: Rohde&Schwarz).The bumper fascia normally consists of several layers, see example in Fig.9.337566015062200033947101144270003451860101092000321691073152000305181048387000right337185Air in front of fasciaClear coat (typ. 30?m thick)Paint (typ. 15?m thick, can contain metallic particles)Base coat (typ. 10?m thick)Basic plastic (typ. 2.8mm thick)00Air in front of fasciaClear coat (typ. 30?m thick)Paint (typ. 15?m thick, can contain metallic particles)Base coat (typ. 10?m thick)Basic plastic (typ. 2.8mm thick)Figure 9: Cross section of an exemplary bumper fascia (source: HELLA).Metallic particles inside the paint have a large influence on its dielectric properties (dielectric constant r or dielectric susceptibility χe, see Fig. 10).Figure 10: Dependency of dielectric susceptibility (“elektrische Suszeptibilit?t”) from weight content of metal (“Metallanteil”) inside the paint [i.20].If a bumper colour mismatch is observed during production, then the layer stack of base coat, paint and clear coat may be repeated multiple times, resulting in the range of 10 dielectric layers or more.The below presented figures with simulation results are based on the solution of the Fresnel equation.Fig 11, for a planar fascia bumper with one layer stack of base coat, paint and clear coat, shows the one-way attenuation at 0° incident angle versus frequency.Fig 12, for a planar fascia bumper with one layer stack of base coat, paint and clear coat, shows the one-way attenuation at 79 GHz. Fig 13, for a planar fascia bumper with two layer stacks of base coat, paint and clear coat,shows the one-way attenuation at 79 GHz for eps_r=20 and both polarisations. Fig 14, for a planar fascia bumper with two layer stacks of base coat, paint and clear coat, shows the one-way attenuation at 79 GHz for eps_r=20 and both polarisations for various basic plastic thicknesses. Fig. 11: Example of one way attenuation at 0° incident angle for planar fascia with a single stack consisting of primer, metallic paint and clear paint layers. In this figure, six different metallic concentrations are considered corresponding to six different paint colours.Fig. 12: Example of one-way attenuation at 79 GHz for planar fascia with a single stack consisting of primer, metallic paint and clear paint layers. In this figure, six different metallic concentrations are considered corresponding to six different paint colours Fig. 13: Example one-way attenuation at 79 GHz for planar fascia with two stacks of 3 layers each, consisting of primer, metallic paint and clear paint.Fig. 14: Example of one way attenuation at 79 GHz for planar fascia with two layer stacks of primer, metallic paint and clear paint and varying basic plastic thicknesses..It becomes obvious that the attenuation of the bumper fascia depends on the frequency, the incident angle, the structure of the paint, the polarisation, the number of layer stacks and thickness of basic plastic. In addition, but not considered more in detail here, also the actual curved 3D shape of the fascia, varying from vehicle model to vehicle model, influences the attenuation.The automotive industry believes that bumper attenuation has relatively small variations. Therefore, it is concluded that power limits applied to the sensor alone would be acceptable. This avoids the situation of split responsibility between the sensor and vehicle manufacturer and also avoids the need to specify or refer to bumper attenuation within a harmonized standard for a sensor.7.2Status of technical parameters 7.2.1Current ITU and European common allocationsThe following table lists the existing spectrum allocation s and applications that are in major use in Europe according to the up-to-date relevant provisions of Article 5 of ITU Radio Regulations and those of the European Common Frequency Allocations Table defined in ERC Report 25 [i.27].Table 6: Spectrum allocations and major European uses in candidate frequency range 74 GHz-81 GHz75,5 GHz - 76 GHzRR 5.561 ECA35BROADCASTING BROADCASTING-SATELLITE FIXEDFIXED-SATELLITE (SPACE-TO-EARTH)Amateur Amateur-SatelliteFixedRadiodetermination applications AmateurAmateur-satellite Space research76 GHz - 77,5 GHzRR5.149Amateur-Satellite AmateurRADIO ASTRONOMY RADIOLOCATIONSpace Research (space-to-Earth)Amateur-satellite Radio astronomy Amateur Radiolocation (civil) Railway applicationsTransport and Traffic Telematics (76-77 GHz) Radiodetermination applicationsShort Range Radars (77-81 GHz)77,5 GHz - 78 GHzRR5.149RADIOLOCATION (5.559B) AMATEUR-SATELLITESpace Research (space-to-Earth) AMATEURShort Range Radars (77-81 GHz) Radiodetermination applications Radio astronomyAmateur Amateur-satellite78 GHz - 79 GHzRR5.149 RR5.560Amateur Amateur-Satellite Radio AstronomySpace Research (space-to-Earth) RADIOLOCATIONRadio astronomy Amateur-satellite Amateur Radiolocation (civil)Short Range Radars (77-81 GHz) Radiodetermination applications79 GHz - 81 GHzRR5.149RADIO ASTRONOMY RADIOLOCATIONAmateur-Satellite AmateurRadiodetermination applications Short Range Radars (77-81 GHz) Radiolocation (civil)Radio astronomy AmateurAmateur-satellitePertinent RR/ECA footnotes quoted verbatim from ERC Report 25 [i.17]:ECA 35: In Europe the band 75,5-76 GHz is also allocated to the Amateur and Amateur Satellite services.RR5.149: In making assignments to stations of other services to which the bands:…76-86GHz, … are allocated, administrations are urged to take all practicable steps to protect the radio astronomy service from harmful interference. Emissions from spaceborne or airborne stations can be particularly serious sources of interference to the radio astronomy service (see Nos. 4.5 and 4.6 and Article 29). (WRC-07)RR5.559B: The use of the frequency band 77,5-78 GHz by the radiolocation service shall be limited to short- range radar for ground-based applications, including automotive radars. The technical characteristics of these radars are provided in the most recent version of Recommendation ITU-R.M.2057 [i.22]. The provisions of No. 4.10 do not apply. (WRC-15)RR5.560: In the band 78-79 GHz radars located on space stations may be operated on a primary basis in the earth exploration-satellite service and in the space research service.RR5.561: In the band 74-76 GHz, stations in the fixed, mobile and broadcasting services shall not cause harmful interference to stations of the fixed-satellite service or stations of the broadcasting-satellite service operating in accordance with the decisions of the appropriate frequency assignment planning conference for the broadcasting-satellite service. (WRC-2000)7.2.2Sharing and compatibility studies already availableIn 2004, when developing the regulation for automotive radars in Europe compatibility studies against the relevant radio services were conducted.The assumed technical parameters for automotive radars in ECC Rep 56 were based on the available technology at that time. The parameters and the description of automotive radars that were used in the studies were presented in ETSI TR 102 263 [i.8] At that time, it was assumed that the 79 GHz radars would use the same technology as at that time available 24 GHz UWB radars would use.Since then radar technology has evolved, so that the assumptions taken at that time can be considered outdated. Despite the evolution in radar technology, the relevant regulation has not been updated since then.In preparation of implementing a national regulation for 79GHz, several countries carried out individual studies and analysis.In 2012, in preparation for the development of a regulation for 79GHz automotive radars in the US a test was conducted at Kitt Peak mm wave observatory [i.32]. For the test 2 automotive radar manufacturers provided samples. In order to be able to detect the signal of the automotive radars at the observatory an additional plane reflector was used to redirect the beam from the receiver to the ground, rather than utilizing the main dish surface in order to simulate a direct line of sight interference situation.It was concluded that an avoidance zone of 30-40 km around the observatory would be needed, in order to keep the interference from an automotive radar below the threshold defined in RA.769-2. Further on it was concluded that in areas without direct line of sight situation or by applying mitigation measures as described in the report, smaller avoidance zones might suffice.In the preparation process for WRC-2015, AI 1.18, a report Rep M.2322 [i.26] was developed analyzing the compatibility between the existing services and automotive radar in the band 77-81GHz. The technical parameters of the automotive radars that were used in the studies are given in ITU-R Rep M.2057 [i.22].The studies provided in the report were conducted only based on the consideration of power levels. It is noted in the report, that no SRS (space-to-Earth) systems have been identified to date in the frequency range 76 GHz to 81 GHz.The report concludes that the theoretical studies and observations presented indicate that the required separation distance between automotive radars and incumbent services could range from less than 1?km to up to 42+ km, depending on the interference scenario and deployment environment. These results were based on worst-case assumptions and did not take into account the effects of terrain shielding, terrain occupation and the implementation of mitigation techniques to reduce the possibility of interference to incumbent services. When these factors are taken into account, the possibility of co-channel interference to incumbent services from automotive radars is sufficiently low and manageable. Therefore, it can be concluded that in the 77.5-78 GHz band, sharing is feasible between automotive radars and incumbent services.It was further concluded, that any potential cases of interference between automotive radars and incumbent services could be addressed by mitigation factors such as terrain shielding, emission power limits and quiet zones.WRC-2015 adopted RES 759, that lead to the development of a new report analyzing the compatibility between the Radio Location Service and the Radio Astronomy Service in the frequency band 76-81GHz .This report considers automotive radar sensors as typical examples for the Radio Location Service in the band.The new report RA.[coexistence] is currently in draft stage and is planned to be published in June 2019. Past studies ignored the radar modulation (FM sweep) used by automotive radars and by doing that neglected mitigation effects and thus achieved too stringent requirements against automotive radars.An exception is the proposal from 2011, was presented in [i.33], giving a theoretical study on interference between 79 GHz automotive radars and radio astronomy stations (RAS) was performed taking the following mitigation effects into account:the automotive radar is considered as instantaneously wideband because of much faster modulation speeds than the RAS integration time.the automotive radar signal reaching the RAS contains a random phase modulation because of vehiclemovement / vibrations / limited quality of VCO.That results in the interference signal appearing at the RAS as incoherent band-limited noise. Furthermore, due to vehicle driving, the antenna gain in the direction from the vehicle to a RAS varies duringRAS integration time and a statistical distribution is considered for that.From all that the study derives and proposes a mitigation factor to be considered in addition to a classical I / N calculation.Here, it is now proposed to overtake this argumentation of [i.33] in order to achieve additional mitigation but apply it to current radar parameters. Today, automotive radars typically use analogue modulation schemes with linear chirps (see illustration in Fig. 15). Chirp durations are in the order of 10 ms for slow chirps or in the order of 10 ?s for fast chirps.Fig. 15: Illustration of analogue modulated radar transmit emission.Newly under consideration for automotive radars are digital modulation schemes, for example with phase modulation or OFDM (see illustration in Fig. 16).Fig. 16: Illustration of digital modulated radar transmit emission.In all cases the emission follows a periodic cycle to duration TCylce (in the order of 50 ms) which is subdivided into an active measurement interval of duration TEmission (in the order of 20 ms) and a processing of sampled results (duration TCycle – TEmission).7.3Information on relevant standards Table 7 lists the relevant standards for the band 77 – 81 GHz TypeApplicationFrequency Ranges [GHz]ETSI StandardStatusRemarkResponsibleETSI TC ERMGenericShort Range Devices (SRD)40 to 246 GHzETSI EN?305?550 [i.44]EN Approval Procedure (ENAP) startedRED compliantTG28SRDTank Level Probing radar (TLPR)4,5 to 7 GHz, 8,5?to 10,6 GHz, 24,05 to 27?GHz, 57 to 64 GHz, 75?to 85 GHzETSI EN?302?372?[i.45]Cited in the OJEURED compliantTG UWBSRDLevel Probing Radar (LPR)6 to 8,5 GHz, 24,05 to 26,5?GHz, 57 to 64?GHz, 75 to 85?GHzETSI EN?302?729?[i.46]Cited in the OJEURED compliantTG UWBAMATEURCommercially available amateur radio equipmentNot specified in the standard EN 301 783 [i.47]Cited in the OJEURED compliant TG 26SRDObstacle Detection Radars for Use on Manned Rotorcraft76 – 77 GHz EN 303 360 [i.48]Published RED compliant TG SRRSRDPart 1: Ground based vehicular radar76 – 77 GHzEN 301 091 -1[i.16] Under revision TG SRR SRDPart 2: Fixed infrastructure radar equipment76 – 77 GHz EN 301 091 - 2 [i.49]Under revision TG SRR SRDPart 3: Railway/Road Crossings obstacle detection system applications 76 – 77 GHz EN 301 091 – 3[i.50]Under revision TG SRRSRDShort Range Radar equipment operating in the 77 GHz to 81 GHz band77 – 81 GHz EN 302 264 [i.17]Under revision TG SRR Fixed LinksCharacteristics and requirements for point-to-point equipment and antennas1,3 – 86 GHzEN 302 217 [i.51]Published RED compliant ATTMTable 78Radio spectrum request and justificationFrank and Ralf will review this section Align/ reuse text with LPR SRDoc TR 103595The current regulation for automotive radars in the frequency range 77-81 GHz ([i.10], [i.11]) was developed and introduced in 2004 on the basis of non-interference/ non-protection, with accordingly very stringent limits based on the results from [i.9] to protect primary radio services (e.g. Radio astronomy, Radiolocation). This resulted in the existing regulation [i.10] and [i.11]. This includes the following elements that the 79 GHz frequency range (77-81 GHz) is designated for Short Range Radar (SRR) equipment on anon-interference and non-protected basis with a maximum mean power density of -3 dBm/MHz e.i.r.p.associated with an peak limit of 55 dBm e.i.r.p.;that the maximum mean power density outside a vehicle resulting from the operation of one SRR equipmentshall not exceed -9 dBm/MHz e.i.r.p.; World Radio Conference 2015 decided to allocate the frequency band 77,5-78 GHz to the Radiolocation Service on a co-primary basis but limited to ground based radars as outlined in the RR Footnote 5.559B [i.21]. With this decision the full frequency range 76-81 GHz is now allocated to the Radio Location Service. Details about the status and the allocations are given in article 5 of the RR [i.21].The frequency range 77-81 GHz plays a key role for future radar sensors because of its large available bandwidth. ITU-R Recommendation ITU-R M.2057 [i.22] was developed to provide the system characteristics of automotive radars operating in the frequency band 76 - 81 GHz for intelligent transport systems applications. Up to 2018 no automotive radar sensor for the range 77 – 81 GHz was placed on the market in Europe for the following reasons: For many years, the RF circuit technology was not powerful enough to support the frequency range at acceptable cost (Ultra Wide Band radar around 26 GHz was more cost effective at that time). With the introduction of SiGe and CMOS RF devices some years ago that situation now has improved. Especially the migration to CMOS based RF technologies, permit the integration of RF and processing capabilities within devices, significantly reducing the cost for radar devices. These SoC (system on Chip) platforms provide the ability to implement digital modulations to significantly improve the efficient and effective use of spectrum through coding schemes. Improvements in technology facilitate sophisticated technics to enhance mutual co-existence between multiple devices utilizing both transmitter and receiver interference mitigation and ejection, such as code correlation, permitting higher densities of devices to securely and safely co-exist in close proximity.For many years, a regulation for automotive radar in this band was not available in important automotive markets outside Europe. With the decision of World Radio Conference 2015 that situation started to improve as seen for example by the recent respective new regulation in the United States and in other regions and countries (see Annex B). But these new regulations are more permissive compared to the existing European regulation for 77-81 GHz. To harmonize as much as possible the European Regulation with the regulation in other areas of the world and key markets is one main issue for this SRDoc. The European regulation for 77-81 GHz was approved in 2004 ([i.10], [i.11]) with the intention to transfer the known functions of 24 GHz UWB short range radars (e.g. for parking support and blind-spot detection) to the 79 GHz band and as such does not anymore meet the needs of current use cases. The usage of 24 GHz UWB short range radars was permitted according to [i.12] only for a limited time period due to coexistence problems with passive radio services and fixed radio services. In the current regulation ([i.10], [i.11]) a fixed bumper loss of 6dB is assumed, to ensure a maximum mean power density of -9dBm/MHz outside the vehicle. The manufacturer of a radar sensor cannot directly control the power level outside the vehicle, as sourcing and specification of the bumper and mounting and assembly of these elements are not within the responsibility of the radar sensor manufacturer With the adoption of the RE-directive the responsibility to comply with the limit of -9dBm/MHz outside the bumper would be that of thevehicle manufacturer. With that it is impossible for the component manufacturer to declare conformity with the -9dBm/MHz limit.The existing European regulation is limited to short range radar applications, but the required use cases are for short range, mid range and long range radar applications–to support effective solutions for safety enhancement in ground based vehicles. These needs are more general and include also functions with larger detection ranges and thus larger required transmit power. The use of the band 76-77 GHz is in the meanwhile permitted in Europe for a wide range of radar applications defined as transport and traffic telematics devices [i.2] In the European regulation, the Usage includes Annex 5 of [i.1] for ground based vehicles, infrastructure systems, obstacle detection radars for rotorcraft use; Annex 4 of [i.1] for obstruction/vehicle detection at railway level crossings. This creates a more general spectrum use in this band with more potential interferers for all radars. This evolution of use in the 76-77 GHz was not foreseen when the 77-81GHz regulation was developed.To overcome the above mentioned shortcomings of the current regulatory situation of short range radar applications in the range 77-81 GHz in Europe and to foster the further development of driver assistance systems it is proposed here to further develop the European regulation for automotive radars in the range 77 – 81 GHz as described in detail in the following.Editorsnote 20190326 concept for the request for change of regulation was developed during TG SRR M38Editorsnote 20190325: fix request?The main change is the removal of a single PSD limit and the introduction of mean power limits depending und bandwidth usage of 50 dBm in the full bandwidth of the transmission. This change would align the European regulation for vehicular radars in the band 77-81 GHz with other areas of the world (e.g. with FCC Part 95) and would align the limits in 77-81 GHz with 76-77 GHz. At the first place this looks like a huge increase of the limit when comparing the 50 dBm mean power limit with the previous PSD limit of -9 dBm/MHz (outside the vehicle). But it needs to be considered that the resulting power spectral density will be well below the mean power value due to the usually large occupied bandwidth of the systems. Typical system characteristics of future vehicular radar systems in the band 77-81 GHz are provided in clause 6.1.1, Table 2 and 3. From there we can see that the PSD of future short range and ultra-short range radar applications are still below the current limits (-3/-9 dBm/MHz); only mid- and long-range radar applications would need to exceed the old PSD limits but they would only require a smaller bandwidth (usually arround500 MHz). Due to the smaller bandwidth of the mid- and long-range radars the occurrence probability to overlap with existing radio users will be much lower than for short- and ultra-short range radars. In addition it is expected that in maximum two medium/long-range radars will be installed in vehicles, while a higher value is expected for short- and ultra-short range radars.The optimal solution for ground based vehicular radars would be to simply allow 50 dBm without any further restriction, but certain mitigation measures might be possible to ensure the coexistence with other radio users (e.g. correlation of Tx power with bandwidth, band plan). Such mitigation measures would need to be developed during the process within CEPTTable 8: summary of the elements that are proposed to be changed No Action Topic 1Change:the scope of the current regulation from automotive short range radars to Ground based vehicular radar equipment2Change: from power spectral density to mean power limit in the full band3Establish: a 50 dBm mean power limit mapower levels according to values given in table 3 4Maintain: Current 55 dBm peak power5Removal:of the limit outside the vehicle which considers a fixed bumper attenuation of 6 dB9RegulationFrank and Ralf will review this section Reflect the revised request as outlined in chapter 8Align/ reuse text with LPR SRDoc TR 1035959.1Current regulationThe operation of automotive radars in the band 77-81 GHz is regulated with ECC Decision (04)03 [i.10]and EC decision 2004/545/EC [i.11]. [i.10] contains the following regulatory text:Title: “The frequency band 77-81 GHz to be designated for the use of Automotive Short Range Radars”Considering l: “l)that SRR-equipment is not considered as a safety of life service in accordance with the Radio Regulations, therefore SRR must operate on a non-interference and non-protected basis in accordance with the Radio Regulations.”Decides 1:“that for the purpose of this Decision, SRR equipment are defined as applications providing road vehicle based radar functions for collision mitigation and traffic safety applications;Decides 2: “that the 79 GHz frequency range (77-81 GHz) is designated for Short Range Radar (SRR) equipment on a non-interference and non-protected basis with a maximum mean power density of -3 dBm/MHz e.i.r.p. associated with an peak limit of 55 dBm e.i.r.p.;”Decides 3: “that the maximum mean power density outside a vehicle resulting from the operation of one SRR equipment shall not exceed -9 dBm/MHz e.i.r.p.;”[i.11] contains the following regulatory text:Title: “Commission Decision of 8 July 2004 on the harmonisation of radio spectrum in the 79 GHz range for the use of automotive short-range radar equipment in the Community”Article 1: “The purpose of this Decision is to harmonise the conditions for the availability and efficient use of the 79 GHz range radio spectrum band for automotive short-range radar equipment.”Article 3: “The 79 GHz range radio spectrum band shall be designated and made available for automotive short-range radar equipment as soon as possible and no later than 1 January 2005 , on a non-interference and non-protected basis.The maximum mean power density shall be of - 3 dBm/MHz effective isotropic radiated power (e.i.r.p.) associated with a peak limit of 55 dBm e.i.r.p. The maximum mean power density outside a vehicle resulting from the operation of one short-range radar shall not exceed - 9 dBm/MHz e.i.r.p.”9.2Proposed regulationThe proposed changes to [i.10] are summarised in Table 9 and the proposed changes to [i.11] in table 10. noReference Proposed change Background1Full document Change Term automotive short range radarsTo Ground based vehicular radar equipment to widen the scope of the regulation and to avoid confusion between the use case and rf coverage of the device and the implemented functions 2Full documentDelete references to “must operate on a non-interference and non protected basis in accordance with the Radio regulations” e.g. in considering l and decides 2.Elevation of the regulatory status of vehicular radar, to ensure the protection of Vehicular radar. Vehicular radar provides significant contribution to road safety: driver assistance functions and autonomous driving vehiclesHarmonization of the regulatory environment for vehicular radar with other countries eg USA (co-primary status) will help to further increase acceptance and deployment of vehicular radars. World Radio Conference 2015 decided to allocate the frequency band 77,5-78 GHz to the Radiolocation Service on a co-primary basis but limited to ground based vehicular radars as outlined in the RR Footnote 5.559B [i.21]. 3Decides 2Change decides 2 that it reads: that the 79 GHz frequency range (77-81 GHz) is designated for Ground based vehicular radar Short Range Radar (SRR) equipment on a non-interference and non-protected basis with a maximum mean power limit density of -3 dBm/MHz 50 dBm e.i.r.p. associated with an peak limit of 55 dBm e.i.r.p.;based on the justification in chapter 8 5Decides 3Delete Decides 3 completely based on the justification in chapter 8 Table 9: Proposed revisions to ECC Dec (04)03 [i.10]noReference Proposed change Background1Full document Change Term automotive short range radarsTo Ground based vehicular radar equipmentto widen the scope of the regulation and to avoid confusion between the use case and rf coverage of the device and the implemented functions 2Article 3, First paragraph, last sentence Delete ..on a non-interference and non-protected basis Elevation of the regulatory status of vehicular radar, to ensure the protection of Vehicular radar. Vehicular radar provides significant contribution to road safety: driver assistance functions and autonomous driving vehiclesHarmonization of the regulatory environment for vehicular radar with other countries eg USA (co-primary status) will help to further increase acceptance and deployment of vehicular radars. World Radio Conference 2015 decided to allocate the frequency band 77,5-78 GHz to the Radiolocation Service on a co-primary basis but limited to ground based vehicular radars as outlined in the RR Footnote 5.559B [i.21]. 3Article 3,Second paragraph replacemaximum mean power density of -3dBm/MHz e.i.r.p.by maximum mean power of 50 dBm e.i.r.p.based on the justification in chapter 8 4Article 3,Third paragraphDelete completely based on the justification in chapter 8Table 10: Proposed revisions to EC decision 2004/545/EC [i.11]Annex A:Overview of current and future use casesA.1 Advanced Driving Assistance Systems: descriptions of features & use casesA1.1 Adaptive Light Control Editorsnote 20190327: request confirmation from Magna that the Figures in A.1.2 and A1.20 can be used in the documenztTypical BW less than 1 GHzTypical range XYZ m Matrix lighting is adapted based on inputs from ADAS sensors to control illumination on oncoming traffic, while providing maximum ilumination for roadway, road signs, intersections or points of interest.42431838100000Closed loop illumination control of traffic signs, etc. to achieve optimum illumination to enhance FCM detection potential. Blanking, shaping, highlighting, adaptive aiming and path planning potential.Figure A.1: tbdKey System Elements:Matrix LED Lighting, RadarCameraLocalizationA1.2Forward Collision WarningTypical BW 1GHzTypical range less than 500m136295836277800Forward Collision Warning provides a early warning to the driver of a potential collision risk, prompting action by the driver to mitigate the risk. Ignoring the warning, causes the AEB function to be activated, where equipped.Figure A.2: source MAGNA Key System Elements:RadarCameraA1.3Automatic Emergency BrakingTypical BW 1GHzTypical range less than 300m44077252260500AEB alerts drivers to collisions with vehicles in their path. If they do not react to the alerts, it automatically brakes to mitigate or avoid a collision. This can be demonstrated two ways: 1) camera only and 2) fusion of a camera and Radar. Figure A.3: tbdKey System Elements:RadarCameraBraking ControlA1.4Automatic Cruise Control (ACC)1092117632266 Typical BW 1GHz Typical range 300mACC is normally used under highway conditions and in essence, is a system which maintains a constant distance or time to a lead vehicle when the vehicle is on highway (road where non-motorised vehicles and pedestrians are prohibited). In combination with Front Corner Radar, Pedestrian & VRU (Vulnerable Roadway User with AEB, LKA features, urban scenarios above 30 kph are supported.. Figure A.4: tbdKey System Elements:RadarCameraBraking ControlA1.5Traffic Sign Recognition / Intelligent Speed Control111633091186000 Typical BW 1GHzTypical range 100mThe traffic sign and traffic light recognition system provides advisory, warning or intervention actions based on inputs from the detected signs or traffic lights. The source of information shall be an electronic map data with a system that can read the actual road signs. The combination of both technologies, apart from scoring more points in NCAP, shall be a reliable source of information for a variety of other functionalities, e.g. bend speed warning, temporary roadworks and for areas where mapping has not yet been undertaken (e.g. new road builds). The traffic light functionality shall be an optical based system. Figure A.5: tbdKey System Elements:Navigation dataCameraBraking Control includes radarA1.6Enhanced Blind Spot MonitoringTypical BW below 500MHz Typical range below 100m141859090562100 Enhanced blind spot monitoring is a convenience feature, providing the driver with a warning, typically located in the rearview mirror, for vehicles in the blind spot zone or quickly approaching the vehicle. Coverage includes merging scenarios, with the incorporation of lane marking information. Vehicles approaching in the adjacent lane are reported up to 30m behind the vehicles (10m/s closing speed maximum). Where Lane Keep Assist is included, steering counter torque will be provided to the driver, providing an indication that a lane change is not recommended. The driver always maintains control of the decision to change lanes.Figure A.6: tbdKey System Elements:RadarCameraA1.7Lane Keep AssistTypical BW less than 500MHzTypical range 500mEYERIS? solutions for lane detection are optimized for every kind of lane marking, thus providing a reliable performance in every market and every corner of the world. 137060634720700EYERIS? features either signal a warning to the driver prior to lane departure or automatically intervene with the car’s controls to deter the driver from moving out of their lane. Figure A.7: source MAGNA Key System Elements:Steering and/or Braking Control (including radar)CameraA1.8Lane Change AssistTypical BW less than 500MHz Typical range less than 150m142621055372000Lane Change Assist and cross traffic alert system extended the warning zone to support warnings at up to 70m behind the vehicle or in crossing traffic situations. Required to support high speed overtaking for European Autobahn scenarios and performance exceeding NHTSA NCAP BSD requirement. Figure A.8: tbdKey System Elements:Front CameraCorner radar, see clause A1.1.A1.9Traffic Jam AssistTypical BW 2GHzTypical range 100m121983596688400ACC (see clause A1.5) is normally used under highway conditions and in essence, is a system which maintains a constant distance or time to a lead vehicle when the vehicle is on highway (road where non-motorised vehicles and pedestrians are prohibited). Traffic Jam Assist acts in combination with Front Corner Radar, LiDAR, Pedestrian & VRU (Vulnerable Roadway User) with AEB, LKA features, in urban scenarios to provide full speed range ACC capabilities including Stop & Go traffic. The system maintains the current driving lane, permitting the driver to complete lane changes. Figure A.9: tbdKey System Elements:Camera RadarCorner RadarLidarSteering &/or Braking ControlA1.10Rear Cross Traffic AlertTypical BW 2GHzTypical range 100mBacking in a busy shopping mall parking lot (cars, shopping carts, pedestrians walking), the cross traffic alert system scans for traffic, pedestrians and range to surrounding objects. The driver is issued warnings via a mirror icon. In combination with Rear Pedestrian AEB, an expanded range of coverage is realized with the fusion of UPA, SVS and corner radar for enhanced security.Figure A.10: source MAGNAKey System Elements:Corner Radar, Rear Camera, UPA,SVS,Braking ControlA1.12Rear Cross Traffic Alertsee A1.11 double entry/ clarify with Magna If the vehicle is stationary, the driver attempts to pull away and the system detects one or more targets which may be at risk of collision, either within the intended lane / path of travel or which are likely to move into the lane / path of travel, the system shall provide a warning to the driver indicating location of the target at risk..Figure A.11: tbdKey System Elements:Front Camera, Front Corner Radar, UPA, SVS,Braking ControlA1.11Front Junction-Intersection AssistTypical BW 4GHzTypical range below 100mIf the vehicle is stationary and the driver attempts to initiate forward motion which causes risk of collision due to some form of cross traffic or object which is stationary ahead, the system shall inhibit the pull-away.Figure A.12: source MAGNAKey System Elements:Camera, Corner Radar, SVS,UPA,Braking ControlA1.12Highway Chauffer Covers several cateogries that are already covered above . sensor fusion application/ multi sensor This feature is an on-demand autonomy solution that allows the driver to enable Level 3 (SAE) driving. The driver’s readiness and ability to resume control is continuously monitored. The driver is required to monitor the driving task, and when requested to take back control, they will be given 3 seconds to do so.Highway Chauffer handles all required driving on limited access highways with driver supervision. It handles lane management, speed modulation, and path planning.Figure A.13: tbdKey System Elements:Front Radar(s)Camera, Driver Monitoring,Steering & Braking ControlA1.13Rear – Auto Emergency BrakingTypical BW 4GHzTypical range less than 10mUltrasonic-only or ultrasonic+camera-fusion provides obstacle detection and evaluation for Rear Automatic Emergency Braking (Rear AEB). The feature will automatically brake in case an object is in the path of the vehicle supporting NCAP requirements. Detection of the entire FMVSS 111 and NCAP reduces harsh emergency braking by providing control of rear backing speeds & comfort stopsFigure A.14: tbdKey System Elements:UPA,Rear Camera,Radar,Braking ControlA1.14Automatic Lane ChangeTypical BW 2GHzTypical range 50m or lessAutomated Lane Change Assist supplements ACC function to autonmously initiate and execute an overtaking manuever. System anticipates the need for overtaking manuever, monitors the driving situation and available opportunities to change lanes, selects the desired opportunity, initiates turn signal, changes lanes & adjusts speed to match the traffic flow. Automatically returns to the original lane after passing the preceeding vehicleFigure A.15: tbdKey System Elements:Camera360° Radar,Steering & Braking ControlA1.15Automated Parking Assist (APA)Typical BW 4GHzTypical range less than 10mUltrasonic-only or camera+ultrasonic-fusion automated parking systems detects obstacles in the vehicle’s path, open parking spots and performs parallel or perpendicular parking maneuvers to park the car automatically. In combination with obstacle detection, the Rear Automatic Emergency Braking (Rear AEB) feature will automatically brake in case an object is in the path of the vehicle supporting NCAP requirementsFigure A.16: source MAGNAKey System Elements:UPA,SVSSteering Control,Braking ControlA1.16Home Zone Automated Parking (HZAP)Typical BW 4GHzTypical range less than 10mAn Ultrasonic or UPA+Vision fusion system for assisting the driver by automating the repetitive tasks such as parking in/out of known (learned) parking spots. Once the desired spot and the associated approach are stored through a short learning/training session, HZAP system will maneuver the vehicle autonomously to a memorized parking spotFigure A.17: source MAGNAKey System Elements:Secure Connectivity, UPA, SVS,RadarSteering & Braking ControlA1.17Valet ParkingTypical BW 4GHzTypical range less that 10mThe driver exits the vehicle at a drop-off area and uses a remote control system, such as a fob or smart phone application, to send the vehicle away to park itself. The driver has no further interaction with the vehicle and the vehicle parks itself in a suitable parking location. The space is allocated by a carpark control system. After some time, either predefined or upon driver request the vehicle drives itself to a pickup area to meet the driver, (the summon function). The system should be capable of communicating with the driver using a remote device to allow the driver to go to the vehicle rather than summon the vehicle.Figure A.18: tbdKey System Elements:Secure Connectivity,Camera, 360° Radar, UPA, LiDARSteering & Braking ControlA1.18Highway PilotSome sensors in this application would need Typical BW 4GHzTypical range 500mFunction based on sensor fusion This feature is an on-demand autonomy solution that allows the driver to enable Level 4 (SAE) driving. If the driver is required to take back control, they will be given 10 seconds to do so. Enhanced biometric, driver monitoring required.Highway Pilot handles all required driving on limited access highways with driver supervision. It handles lane management, speed modulation, and path planning.Figure A.19: tbdKey System Elements:Secure ConnectivityCamera, 360° Radar, UPA, LiDAR,Driver Monitoring,Steering & Braking ControlA.2 Advanced Driving Assistance Systems for other kind of ground based vehicles: descriptions of features & use casesA2.1GeneralRadar sensor covered by EN 301 091-3 [i.X] are designed to realize a variety of different driver assistant functions and safety supporting functions. Based on the complexity with classes were specified to simply/generalize the RX-tests.More details are also provided within TR 102 704 [i.X]A2.2Trains (locomotive and train cars,…)-545161262007Detection of ?known“ objects for a defined breaking /stoppingCorrect speed over ground and reaction if ?breaking“ needs to be corrected (shorter)Rolling detectionDetection of foreign objects emergency breakingMeasurement of height and lateral position (continuous evaluation status condition during usage). To detect alien objects (e.g. clamps)To avoid damages during constructionCould also be used for Hybrid vehicles to detect catenary see Figure A.230Detection of ?known“ objects for a defined breaking /stoppingCorrect speed over ground and reaction if ?breaking“ needs to be corrected (shorter)Rolling detectionDetection of foreign objects emergency breakingMeasurement of height and lateral position (continuous evaluation status condition during usage). To detect alien objects (e.g. clamps)To avoid damages during constructionCould also be used for Hybrid vehicles to detect catenary see Figure A.23Short summary about use – cases and figures provided in this clauseFigure A.21: tbdFigure A.20: tbd25082513800Figure A.21: Example train construction vehiclesFigure A.22: Examples catenary detection and position measurementFigure A.23: Examples catenary detection and position measurementFigure A.24: collision avoidanceA2.3Tram/MetroUse-cases: collision warning/avoidance and speed over groundFigures:16490950Figure A.25: A2.4Construction / farming vehicles (outdoor)Use- cases (very comparable with automotive use-case): Collision avoidance (crossing collision avoidance / back over collision avoidance / side looking (blind spot)Huge and heavy vehicles with lot of “blind spots” increase of safetyAutonomous devices (automatic coordinated pace)965200336191(correct/real) speed over groundFigure A.26: 1386840332Figure A.27: Figure A.28: A2.5Industrial vehicles / Material handling (indoor/outdoor)Use-cases (fork lifts, working platform):Collision avoidance (if people working in pulled out situation detection ground objects, blind spot detection) Autonomous devices Distance measurement (height over ground / height over headfirst)Benefit for such sensors:Vehicles with lot of “blind spots” and if working indoor difficult to estimate the distance till the celling (headfirst), walls or obstacles on the ground increase of safety206184575620190364723958900Figure A.29: 14019123515300Figure A.30:Figure A.31:A.3Vehicle safety programmes A3.1Vehicle safety programmesThere are several vehicle testing organisations, which rate the available vehicles based on various defined standards. The OEMs are usually interested in fulfilling all requirements of the standards in order to get good ratings for their vehicles. The testing organisations have already developed tests to assess the safety functions that are available for the vehicles. The test organisations develop the test requirements taking into account historical accident and fatality data, the associated state of available technologies, the expected impact of improvements of enhanced driver awareness and/or controlled intervention. In many instances, features have migrated from providing driver warnings (LDW, FCW) to providing automatic reaction to known high collision risk scenarios (LKS, AEB) involving control of the vehicle’s braking or steering system.A3.2New Car Assessment Programs (NCAP) NCAP is one of the most important vehicle testing programme working on several regions worldwide. In Europe, the Euro NCAP is developing feature requirements, performance & test requirements and time schedules when they will be included in the tests. These roadmaps are communicated as targeted implementation dates against which OEMs develop technology application strategies to achieve desired ratings for their vehicles. Generally, OEMs target to make available the technology to reach the maximum possible rating, while also supporting consumer choice with packages including safety technology bundled into available optional content. A3.3EU NCAP Euro NCAP is a voluntary vehicle safety rating system created by the Swedish Road Administration, the Fédération Internationale de l’Automobile and International Consumer Research & Testing, and backed by the European Commission, seven European governments, as well as motoring and consumer organizations in every EU country. The program is modelled after the New Car Assessment Program (NCAP), introduced in 1979 by the U.S. National Highway Traffic Safety Administration. Other areas with similar (but not identical) programmes include Australia and New Zealand with ANCAP, Latin America with Latin NCAP and China with C-NCAP. Figure A.32 gives an overview of the current timeline for the implementation of new safety related radar based functions in the Euro NCAP tests. [i.XX] Editors note: reference to the Euro NCAP website Figure A.32: Euro NCAP Feature Roadmap thru 2025A3.4US NCAP Within the USA, the Department of Transportation’s (DOT), National Highway Traffic Safety Administration (NHTSA) administers the New Car Assessment Program (NCAP). Most recently [i.25], NHTSA has conducted requests for comment on proposals for changes to the NCAP requirements for 2018 and beyond. While the US-NCAP proposals mirror the Euro NCAP in several areas, test procedures and priorities reflect analysis of the past accidents data to affect the greatest potential benefit considering conditions in the US market. Similarly, NCAP regulations in other regions reflect the unique conditions in the market, including local supply availability, setting priorities and timetables for implementation. For global OEM’s, features supporting the global NCAP portfolio of capabilities and performance requirements are necessary. Accordingly, automotive radar technologies require regulatory modification to support the increasing demands for broader perception capabilities to achieve the safety enhancement desired cost effectively.The relevant NCAP testing organisations publish safety reports on new cars, and award 'star ratings' based on the performance of the vehicles in a variety of crash tests, including front and side impacts, collisions with posts, and impacts with pedestrians. The top overall rating is five stars.Testing is not mandatory, with vehicle models being independently chosen by Euro NCAP or voluntarily submitted for testing by the manufacturers. In Europe, new cars are certified as legal for sale under the Whole Vehicle Type Approval regime that does not always apply the same requirements as Euro NCAP. Euro NCAP has stated their position as “Legislation sets a minimum compulsory standard whilst Euro NCAP is concerned with best possible current practice. Progress with vehicle safety legislation can be slow, provides no further incentive to improve, whereas Euro NCAP provides a continuing incentive by regularly enhancing its assessment procedures to stimulate further improvements in vehicle safety.”Combined, the regulatory actions of the EU Commission and the market based product ratings of the Euro NCAP roadmaps will accelerate the implementation of radar based and radar data used in fusion solutions with other perception technologies such as cameras and LIDAR. Globally, similar actions are underway to address the growing social impact of roadway fatalities, injuries, and accidents.A3.5Future autonomous driving vehicles Figure A.33: More detailed description of the SAE levels for automation.In Germany, currently series cars up to level 2 are allowed to be used on the roads. First series cars are available carrying all technology to in principle also support level 3. For levels 4 and 5, fleets of test cars are collecting data on especially assigned roads.With increasing automation level, the number of sensors needed in a car considerably increases for redundancy reasons and measurement accuracy reasons. Typically, these types of sensors are used:Radar Lidar Video By additionally using communication between vehicles the data set used by a car to decide on its next actions can be further improved.Fig. A.34 shows an example configuration of these sensors on a car.Figure A.34: Example configuration of sensors on an autonomous vehicle (Level 3-4).Vehicles capable for higher levels of autonomous driving will have and use more radar sensors. Annex B:summary of Regulations in selected countries for 76-77 GHz and 77 - 81 GHz radar sensorsThe overview provides a summary of selected market areas and countries and illustrates the radio spectrum regulations for radars operating in the frequency range 76 GHz to 81 GHz. The presented table is a snapshot of the regulation at the time when the document was developed. For reference to most recent local regulatory documents should be consulted.It is important to note, that for most countries of the listed countries the regulation and therefore approval scheme and related standard is split for the two frequency bands 76 -77 GHz and 77 – 81 GHz. In 2017 the FCC in the US has merged the frequency regulation for the whole frequency band, which is illustrated by listed frequency range.Key parameters like power requirements and frequency band are shown. Summary of the situation in key market countries For 76 GHz – 77 GHz the technical requirements for acceptance are in principle homogenous and aligned over the listed countries and regions. Only a few countries deviate regarding the typical power parameters and the method applied for verification (examples: reference to conducted power).For 77 – 81 GHz quite a number of countries do not have yet a regulation or are about to work out new regulations and standards. In addition the power requirements show big variation. Specifically the limitation of power density for dedicated usage (vehicle) or in relation to bandwidth will restrict the usage and function of related sensors.Table1: examples for Regulations in selected countries for 76-77 GHz and 77 - 81 GHz radar sensors (10/2018)Country / Region?Regulation / Radio StandardPower *Other**?Regulation / Radio StandardPower *Other??76 - 77 GHz???77-81 GHz??Australia?Radio communications (Low InterferencePotential Devices) Class Licence 2000Version of 27 July 2011Peak: 44 dBm??Radio communications (Low InterferencePotential Devices) Class Licence 2000Version of 27 July 2011Peak: 55 dBmFreq. Range 77 - 81 GHZBrazil?NATIONAL AGENCY FOR COMMUNICATIONSACT NO 11542 OF August 23, 2017 not moving: 200nW/cm?,front looking:60uW/cm?,side/backward looking:30uW/cm?[all at 3m]??not regulatedregulation in process???CanadaCanada??Industry CanadaRSS-251, Issue 2July 201850 dBmPeak: 55 dBmFreq. Range 76 - 81 GHZ??Industry CanadaRSS-251, Issue 2July 201850 dBmPeak: 55 dBmFreq. Range 76 - 81 GHZChina?Micropower (Short Distance) Radio Equipments(revison of regulation in process)Peak: 55 dBm??regulation in process??Europe?EN 301 091 50 dBmPeak: 55 dBm??EN 302 264-3 dBm / MHz(sensor)-9 dBm / MHz(car)Peak: 55 dBmFreq. Range 77 - 81 GHZIndia-Very Low Power Radio Frequency Devices /Equipment for Short Range Radar Systems37 dBm?-not regulated??Japan?ARIB STD-T48 2.210 dBm condburst power(40 dBi Gain -> 50 dBm) ??ARIB STD-T111 1.1Now full 4GHz is allowed 10 dBm condburst power(35 dBi Gain -> 45 dBm) (When OBW is less than 2 GHz, less than 5uW/MHz) Freq. Range 776 - 81 GHZSouth Korea?Technical Standards for Radio Equipment (RRL Notification 2006-84 (2006.8.23))9. Automotive Radar System10 dBm cond individual antanna(50 dBm)??Frequency band 77GHz-81GHz allocated, standard still to be released?Freq. Range 77 - 81 GHZRussia-Appendix 1, Resolution of State Radio Frequency Committee No. 10-09-03 of 29 October 2010"Wireless Alarm and Motion Detection Devices"35 dBm?-Appendix 1, Resolution of State Radio Frequency Committee No. 10-09-03 of 29 October 2010"Wireless Alarm and Motion Detection Devices"-3dBm / MHzFreq. Range 77 - 81 GHZSingapore-IMDA TS SRDIssue 1, 1 October 201637 dBmStationary: 23.5 dBm?-IDA TS UWBIssue 1 Rev 1, May 2011-3dBm / MHzPeak: 55 dBmFreq. Range 77 - 81 GHZUSA?FCC part 95M50 dBmPeak: 55 dBmFreq. Range 76 - 81 GHZ?FCC part 95M50 dBmPeak: 55 dBmFreq. Range 76 - 81 GHZ* ) Power EIRP - if not otherwise stated**) Frequency range is 76GHz -77GHz - if not otherwise statedAnnex C Radar Basics C.1Maximum range Based on the radar range equation the maximum range can be calculated in an ideal situation (e.g. no rain, no multipath, no bumper loss, etc.) Rmax= 4Pt?RCS?c2?G2(4π)3?fc2?PminFormula SEQ Formula \* ARABIC 1 Radar Range EquationWhereRmaxis the maximum range of the radarPt is the transmit power of the radarRCS is the Radar Cross Sectionc is the speed of lightG is the TX/RX antenna gainfc is the carrier frequency Pminis the minimum detectable signal power of the radarP e.i.r.p. is Pt * G According to typical values known from development of 77 GHz automotive radar sensors:E-Band 76-81 GHz antennas have approximately the antenna gain as listed in attached table, based on the basic feature set of the sensor.Sensor operation / FunctionAntenna gain [dBi]Anteanna gain[linear value]Ultra Short Range radar64Short Range Radar1010Mid Range Radar1532Long Range Radar20100Note: For given sensor operations gain of Tx and Rx path is assumed to be equivalent: GTx = GRx , because similar or even same antenna structures and characteristics are used for Tx an Rx path.Radar Cross Section of a child min, child max, motor cycle, motorcycle and car as given in attached table,?Object ReferencedBsqmsqmSmall Child(Child Min [i.55])-130,05Pedestrian(Child Max [i.55])-100,1Bicycle [i.55]-50,34Motor Cycle [i.56]01Car [i.56]1010a minimum detection threshold of -110 dBmA bumper loss in a range of 2 - 8 dB (2 way attenuation) will cause degradation of performance compared to the ideal environment.Open item: Reference: tbd The following tables show the typical sensor performance based on given technical parameters. The maximum detection range for the listed automotive radar types a short-range radar (SRR) detecting the related object properties (RCS) references is calculated based on the potential maximum output power.Table A: Ultra Short range radar (USRR)Max EIRP / Range [m]10 dBm20 dBm30 dBm35 dBm40 dBmSmall Child6,26,211,111,119,719,726,326,335,135,1Child /Pedestrian (Child Max)7,47,413,213,223,523,531,331,341,841,8Bicycle9,817,430,941,255,0Motor Cycle Bike 13,213,223,523,541,841,855,755,774,374,3CarVehicle23,523,541,841,874,374,399,099,0132,1132,1Table B: Short range radar (SRR)Max EIRP / Range [m]10 dBm20 dBm30 dBm35 dBm40 dBmSmall ChildSmall Child7,97,914,014,024,924,933,233,244,244,2Pedestrian (Child Max)Child /Pedestrian9,39,316,616,629,629,639,439,452,652,6Bicycle12,321,938,951,969,2Motor CycleMotor Bike 16,616,629,629,652,652,670,170,193,593,5CarVehicle29,629,652,652,693,593,5124,7124,7166,2166,2Table C: Mid range radar (MRR)Max EIRP / Range [m]10 dBm20 dBm30 dBm35 dBm40 dBmSmall ChildSmall Child10,510,518,618,633,233,244,244,259,059,0Pedestrian (Child Max)Child /Pedestrian12,512,522,222,239,439,452,652,670,170,1Bicycle16,429,251,969,292,3Motor CycleMotor Bike 22,222,239,439,470,170,193,593,5124,7124,7CarVehicle39,439,470,170,1124,7124,7166,2166,2221,7221,7Table D: Long range radar (LRR)Max EIRP / Range [m]10 dBm20 dBm30 dBm35 dBm40 dBmSmall ChildSmall Child14,014,024,924,944,244,259,059,078,678,6Pedestrian (Child Max)Child /Pedestrian16,616,629,629,652,652,670,170,193,593,5Bicycle21,938,969,292,3123,0Motor CycleMotor Bike 29,629,652,652,693,593,5124,7124,7166,2166,2CarVehicle52,652,693,593,5166,2166,2221,7221,7295,6295,6If the 2 way attenuation of the bumper is introduced, the detection range is reduced. Table E shows this on the example an LRR (results without bumper, see table D)Table E: Long range radar (LRR) – considering an additional two-way bumper loss of 6 dBMax EIRP / Range [m]10 dBm20 dBm30 dBm35 dBm40 dBmSmall ChildSmall Child9,99,917,617,631,331,341,741,755,755,7Pedestrian (Child Max)Child /Pedestrian11,811,820,920,937,237,249,649,666,266,2Bicycle15,527,549,065,387,1Motor CycleMotor Bike 20,920,937,237,266,266,288,388,3117,7117,7CarVehicle37,237,266,266,2117,7117,7156,9156,9209,3209,3Table F: loss in range [%] considering different attenuation values for bumper loss two way Attenuation 2 dB4 dB6 dB8 dBRange loss [%]11 %21 %29 %37 %C.2Definition of sensor performance parameters ParameterRemarksDetection rangeMax. range is determined by min. SNR to achieve a desired min. probability of detection and a max. probability of false alarm, see Annex A.2Range resolutionFor frequency modulated radars:= c0 / (2 modulation bandwidth)For pulsed modulated radars:= c0 * pulse duration / 2Separation of two objects in range= 2 * range resolutionMin. difference between detection ranges of two objects for them to be separated because of detection rangeObject (micro-) Doppler speedMax. relative speed is determined by used ADC sampling rate(micro-) Doppler speed resolution= c0 / (2 * carrier frequency * transmit time)Separation of two objects in (micro-) Doppler speed= 2 * (micro-) Doppler speed resolutionMin. difference between relative speeds of two objects for them to be separated because of speedTx, Rx antenna -3dB beam widthDetermined by antenna and radome designSeparation of two objects in angle= object range * sin (-3dB beam width / 2)Min. difference between angles of two objects for them to be separated because of angleC.3SNRFor target reflector in antenna far-field:Receive signal S in FFT spectrum = Tx e.i.r.p. * path loss * target strength * path loss * Rx antenna gain * Rx conversion gainwith:path loss = lambda? / (4 pi object range)?target strength = RCS * 4 pi / lambda?Thermal noise signal N in FFT spectrum = Boltzmann constant * temperature * IF bandwidth * Noise figure * Rx conversion gain / FFT gainSNR = Receive signal S in FFT spectrum / Thermal noise signal N in FFT spectrumC.4Antenna propertiesAntenna size 60° * Lambda / (-3dB beam width)Far-field range 2 * antenna size? / LambdaFar-field antenna gain Efficiency * (pi * antenna size / Lambda)?(source: )Annex :Change HistoryDateVersionInformation about changes<Month year><#><Changes made are listed in this cell>02/20180.0.3TG SRR # 32: outcome of drafting session Feb 14th,201803/20180.0.4TG SRR # 32: outcome of drafting session March 14th, 201803/20180.0.5TG SRR # 32: outcome of drafting session March 16th, 201804/20180.0.6Outcome of drafting session April 3rd,201804/20180.0.7Input document for drafting session April 25th,201804/20180.0.8Output document drafting session April 25th, 201805/20180.0.9Output document drafting session May 22nd, 201806/20180.0.10Output document drafting session June 18th,201806/20180.0.11Output document drafting session June 28th, 201807/20180.0.12Output document drafting session July 6th, 201807/20180.0.13Output document drafting session July 12th, 2018 ( morning)07/20180.0.14Output document drafting session July 13th, 2018 09/20180.0.15Output document drafting session September 11th, 201810/20180.0.16Output document drafting session October 16th, 2018 11/20180.0.17Output document drafting sessions TG SRR M37 Nov 29th, 2018 01/20190.0.18Output document drafting session Jan 18th, 2019 02/20190.0.19Output document drafting session Feb 11th, 201903/20190.0.20Output document drafting session March 13th, 2019 03/20190.0.21Output document drafting sessions TG SRR M38 March 26th, 2019 04/20190.0.22Output document drafting session April 26th,201905/20190.0.23Output document drafting session May 24, 201907/20190.0.24Output document drafting session June 25th , 2019HistoryDocument history<Version><Date><Milestone>Latest changes made on 2017-07-10 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download