Collection Profiles: INDUSTRIAL TRANSFERS AND THE ART OF ...
Collection Profiles: INDUSTRIAL TRANSFERS AND THE ART OF DECALCOMANIA.
Table of Contents:
Introduction
The Collection
Origins of Transfer Ornamentation
Tearne & Sons Company
Production of Transfers
Transferring Techniques
Each one identifies a product
Rare and Unique Collection
“Who has not admired an American railway train, when cars and engine are newly painted and decorated? Who does not look with preference at an omnibus, when finely decorated, and placed along side of one which has only the streets painted on it in large red letter?”
The American Painter and Decorator, March 1876
Image 1.
Image 2.
Introduction
The Canada Science and Technology Museum possesses a rich and comprehensive collection of the late 19th and the early 20th century industrial transfers. Industrial transfers were a form of decals commonly used in Canada, as well as globally, to replace an expensive method of hand painting coats of arms, trade marks, signs, ornaments, letters and numbers on railway equipment, ships and industrial machinery. Properly affixed transfers were highly durable; this fact made them an especially desirable form of lettering and decoration on equipment exposed to various climatic conditions, such as the rail stock running in tropical or extremely dry weather and extensively used with limited care on long distance routes.
The CSTM collection has an unique historical and educational value. Even though the word ‘transfer’ or its American equivalent ‘decalcomania’ was often used to describe a drawing, design, or pattern that may be moved from one surface to another through direct contact, and the decorative technique itself was well known, both were usually associated with chinaware and pottery decoration. (Image 3) Yet industrial transfers, applied for example to railway stock or commercial vehicles, were not as common. To this regard the collection is a valuable resource allowing for the analyses of printmaking techniques of the late 19th century such as lithographic process, as well as studies of industrial object design and the early graphic arts.
The Collection
The CSTM has acquired transfers since its very beginnings. However, the collection has been significantly enriched by two donations received by the Museum in 1975 and in 2000, consisting of transfers collected by Roger Sylvester and by Andrew Merrilees. At present, the Canada Science and Technology Museum holds over 1,500 original designs and, since in many cases there are several copies of the same image, almost 17,000 individual decals, produced between late 1880s and early 1960s. The many duplications in the collection allow for true preservation of one copy, while others may be transferred for display as finished products, or studied for research purposes. For example, the analysis of the paper used to produce a decal can only be performed on the artifact prior to transfer. (Image 4).
Among the most interesting items are 19th century coats of arms produced by a British transfer-maker, Tearne & Sons Co., handmade patterns for letters and numbers used by colonial railways and signs and trade marks produced by the Canada Decalcomania Company for the Canadian National Railways, Toronto Transportation Commission, Consumers’ Gas and other Canadian companies. (Image 5, Image 6) They represent the vanishing phase of decorative arts that originated in Victorian extrinsic ornamentation and carried on well into the first decades of the 20th century. As the styles of the industrial embellishment changed, the role of the artist-craftsman became obsolete, and even as factors such as the range of colours commercially accessible increased, the transfers became a testimony to the past philosophy and technique of decorative arts.
Origins of Transfer Ornamentation
The origin of transfer design is not certain. One debatable story, first recorded in 1871, suggests that John Sadler got an idea of decorating pottery with printed images while watching a group of children ornamenting their doll houses. Indeed, John Sadler and Guy Green – both well-known printers and engravers working in Liverpool, claimed to invent the technique in 1756 to decorate pottery for the famous Josiah Wedgewood. This claim, however is contested by evidence that in 1751 and 1755, John Brooks, an engraver employed by the Battersea Enamel Works, attempted to patent the monochrome transfer technique, which involved etching and inking an image onto a copper plate and then imprinting it onto a wet paper, which in turn was pressed against a piece of pottery leaving an impression. Even if Sadler and Green did not invent the transfers, they perfected the engraving process and printing techniques and inaugurated an underglaze printing, which by the 1770s brought the price of pottery decoration from £2.00 per piece to 6 pens. The technique spread from England to Sweden, Germany, France and to North America. In Germany, the transfers were used to imitate a gold leaf on iron sewing machines and wooden clocks, and soon they were applied to household appliances, coaches, railway cars and industrial machinery around the world. (Image 7, Image 8, Image 9) By 1890 decalcomania had become one of the most common methods of ornamentation of technological artifacts.
Canadians first ventured into the industrial transfer technology in 1871, when Henry McElcheran, a painter from Hamilton, searched for a new way to decorate coaches. During his experiments, he combined glue, sugar glycerine and balsam of fir, creating a perfectly pliable sheets of material, which was easily imprinted by wood cuts, and could have been attached to any surface. Yet, generally in the 19th century, the Canadian market was dominated by imported British and American products. This situation persisted until 1911 when the Canada Decalcomania Company Ltd. opened an office in Toronto and soon produced decals for many Canadian companies. Unfortunately, the transfers in their original paper form were very fragile and the products of the company rarely survived the test of time. Today the decals produced by the Canada Decalcomania are very rare.
Tearne & Sons Company
Most transfers that exist today in their original form, owe their survival to a keen eye of a collector. In 1960s, for example, a British company Tearne & Sons was melting old decals to recover gold and silver used during their production. Fortunately, two Canadian collectors, Roger Sylvester and Andrew Merrilees, managed to purchase the remaining stock from Tearne, before all the transfers were destroyed. They brought the decals to Canada and later donated their priced collections to the Canada Science and Technology Museum.
The Tearne & Sons, Ltd., whose transfers now constitute the majority of the decals preserved by the Museum, was established by Samuel Tearne in 1856. (Image 10) Located in the famous Birmingham Jewellery Quarter, it mainly manufactured jewellery boxes. With the experience in decorative arts and interest in newest technologies the company started by producing transfers for bicycles in the 1870s and by the end of the decade was the main manufacturer of railway transfer art in Great Britain and supplied decals to many major transportation companies worldwide, as well as municipalities and counties, the Royal Household, the British Armed Forces and the Air Force. (Image 11) The company is still in existence and nowadays produces transfers for the famous Orient Express.
Production of Transfers
The chromolithographic transfer technique used to produce most of the decals in the CSTM collection facilitated the reproduction of the multicolour decorations, lettering and numbers on any surface including glass, metal or wood offering a less expensive alternative to hand painting and brushwork. Even though less expensive than the alternatives, the process of preparing transfers was quite complicated and required artistic skills and knowledge of printing techniques. First, the customer provided a transfer manufacturer with a master copy of an image to be reproduced. This copy usually included detailed description of the design, size and colour dyes. (Image 12) Transfer manufacturers were allowed very little creative change to the master design especially in case of the coats of arms approved by the College of Heraldry. In some cases, however, the merit of artistic expression had to be compromised with the functionality; the process of transferring imposed limitations on design and some elements of an image had to be simplified. (Image 13)
After the master image was finalized, it was given to an artist-craftsman who was responsible for engraving it onto lithographic stones. The image was first reproduced on a ‘key stone’ that was not used for printing itself, but served as an outline, a lithographic master copy for other imprints. Next the artist made one engraving for each colour used in the design and carefully examined the colours and shades used on the image in order to prepared dyes. The image from a key plate was then impressed upon lithographic stones producing as many duplicate plates as were required to print the colour image. Each area that required a different colour was drawn on a separate stone. The colour was inked in and preserved with a thin layer of gum arabic. The application of the dyes followed the order, which was the reverse of standard painting - the transparent colours first and opaque last. The colour plates were then given to a pressman, who proceeded with the process of lithographic printing. The first imprint, done on an inexpensive paper, was called a proof; it was inspected for errors, colours were matched against the original design, and any alternations or directions were handwritten and signed by a printer. (Image 14)
The actual printing of transfers required a high degree of skills. The image was impressed on the paper in reverse, in order to transfer it right side up on the surface (Image 15). Every stone had to be carefully aligned to complement perfectly succeeding colours, and with each added dye the face of the image was less visible to the printer, making the process very time-consuming. The parts of the design that were supposed to be filled with pure gold or silver were left empty at the printing stage and when all the other colours were ready, the coat of liquid metal was applied over the entire design. (Image 16) The transfer paper was very sensitive to environmental changes. It expanded and shrank with even slight variations in temperature and humidity, which would make it impossible to align the colours and complete the decal. Many transfer shops were therefore equipped with environmental control units. In fact, the Palm Brothers Decalcomania Company plant in Norwood, OH was the earliest air conditioned building in Ohio. The preparation of the decal paper was de facto the most expensive part of the transfer making. The decal paper classified in the gummed paper division, was not manufactured in mills but was prepared by transfer makers themselves or converters, also called coaters who specialized in finish applications. One of the better-known coaters was the Tullis Russell Brittains, a company which supplied paper to Tearne & Sons in England and Commercial Decal Inc. in the United States. There were two categories of the decal paper: an older type ‘simplex’ or a ‘single paper’ that consisted of a single layer of a heavy water penetrable paper sheet, and newer ‘duplex’ or ‘double paper’ made-up of a nonporous paper and a thin tissue attached to it semi-permanently. The final image imprinted on both types of paper looked identical, and the two could be told apart only by carefully examining the edges of the transfer paper. (Image 17) The edge of the simplex was smooth, but the duplex often revealed the thin tissue separating the backings. The surface of the transfer paper was treated with three layers of coating. An undercoat was made of a starch filling evenly applied over the surface. When this coat was dry, the sheets of paper were polished between hot rollers. Then came a coat of glycerine that made the sheet pliant and prevented fractures in the starched surface. The last layer, called a transfer surface, consisted of starch, albumen and a solution of gum arabic. The sheets, stored in unvarying temperature, were allowed to season between each process for up to 30 days. These special coats allowed the image to separate easily from the paper when transferring the design onto a required surface.
Transferring Techniques
Three different techniques were used to apply transfers to a surface: water release, cement mounting and pressure sensitive process, used mostly for porcelain decoration. The water released decals were the most common type. These were divided into three subtypes: the water slide-off type - as implied by the name, printed right side up and slid off the paper onto a surface face up; the direct transfers that required a light coat of varnish to be applied over the image and then placed in direct contact with the receiving surface, and finally double purpose transfers usually applied on glass and read from either side. The water released, direct transfers were printed on the simplex paper. Originally, the entire decal was saturated before being applied to a surface. When the transfer was placed in water, the mixture of gelatine, albumen and gum arabic separated from the paper and flowed on the water. The transfer was carefully lifted, pressed on the transferring surface and left to dry. The transferred image was always covered with lacquer or varnish to enhance its durability. Since the image could easily be damaged while lifted from the water, a safer technique was developed. First the transferring surface was cleaned of dust or dirt. Then the surface of the transfer was finished with a thin coat of varnish and left to dry. Just before transferring, the image was painted with another layer of varnish and the entire transfer including the backing sheet was pressed onto a surface from the center toward the edges. When the transfer was firmly attached to the surface, the paper layer was slowly saturated with water. This process had to be done precisely to prevent the water from reaching the image layer. The soaked backing paper was then detached from the design. (Image 18, Image 19)
The water-released transfers prepared on the duplex paper required a cement mounting technique. A small area of tissue usually at the edge was first separated from the backing paper. Next, the image was coated with some decal cement applied with a soft cloth and left to set for about 10 minutes. When the cement became tacky, but not thick, the decal was pressed to a clean wet surface and rolled down with a rubber roller or sponge. The wet surface prevented the decal from attaching immediately and made it easier to position the transfer. The backing paper was peeled away starting with a loose corner. The tissue paper and some gum deposit were left over the design and had to be removed with a wet sponge. If these were allowed to dry, they would crack the transfer damaging the image. The affixed transfer was allowed to dry for up to two weeks before being washed with benzine to remove the surplus cement. The final imaged was protected with a coat of varnish.
Each one identifies a product...
“Each one of these Canada Decalcomania Transfers identifies a product. You simply dip them in water and slide them off the paper onto the article” – the Canada Decalcomania promoted its merchandise in 1931. Indeed, the transfers not only adorned common objects, but also expressed and reinforced among the customers the corporate identity of the company, which applied them to its products. (Image 20). These corporate coats of arms, monograms and trade marks constitute the most interesting artistically part of the transfer collection.
In the 19th century it was customary for institutions to have a coat of arms. Railway companies, for example, acquired a device right after their incorporation as a seal for legal documents. They commonly assembled the arms from the devices of the towns they served, or simply placed the company’s name in a garter. The coats of arms in the CSTM transfer collection include, among others, arms of the Great Southern Railway, Great Western Railway, North Western Railway, Barranquilla Railway & Pier Company, East Indian Railways, Egyptian State Railway, and Kenya & Uganda Railway, royal coats of arms and monograms, and numerous devices of cities that were place on public transportation. (Image 21, Image 22, Image 23)
Asides from the transfers designed for railways, the collection also includes examples of images made for shipping companies as well as trade marks of businesses and manufacturers. Among the most interesting trade marks are the images designed by Canada Decalcomania for Pierre Thibault, and placed on fire trucks produced by his company; ACME Decalcomania’s decals for the Canadian Fire Chiefs Association and transfers made by Tearnes for Wagon Repairers Ltd., Pinckering Stock, Robey & Co., Marshall, Sons & Company and Huntley and Palmer to name a few. (Image 24, Image 25) Some of these companies used a simple design that implied an association with a product, but most examples included in the collection show a heavy armorial influence and manufacturers’ preoccupation with overdrawn ornamentation that dominated Victorian times and apparently was still very popular in the first decades of the 20th century. (Image 26, Image 27)
The industrial transfers blended aesthetics and utility. The signs and warnings were designed in simple lettering, but were enriched by colours and shadings; some notices for colonial railways, i.e., Central India Railways were printed in three languages: English and two local dialects. Images that often replaced signs, such as a face of a woman designating “ladies only” compartments, were nothing but schematic; their design was elaborated, with several colours used, and it was obvious that the artistic value of transfers was, in some cases, more important to railway companies than the price of decals (Image 28). The railway companies also devoted much attention to enhancing interiors of trains, and the collection contains many examples of silver and gold interior decoration ornaments, boarders, corner ornaments as well as crowns and monograms intended to adorn the first class cars. (Image 29).
Many decals from the CSTM’s collection evoke interesting stories associated with the clients who ordered the art work. A good example is a simple crest produced for the S.S. Yoma in May 1928, as the ship was being built by W. Denny & Bros. The ship was owned by the British & Burmese Co. and operated as a part of Henderson Line servicing the route from Glasgow to Rangoon. During the World War II, the SS Yoma served as a troopship in the Mediterranean and was a part of the convoy when she was sunk on June 17, 1943 by a U-81 near Derna. Out of 1,670 on board, 389 crew members were saved by the marines from HMAS Lismore, many of whom dived to the sea to help their colleagues. (Image 30)
Rare and Unique Collection
Although there are similar collections, both private and public, in Great Britain, the most notable at the National Railway Museum, the CSTM’s collection with its emphasis on railway decals and companies’ coats of arms is unique in the North American context. Canadian museum transfer collections are rather small and mostly consist of decals already affixed onto another object. Two major public decal collections are located in the United States. The Commercial Decal Company collection, donated to the Smithsonian Institution in 1993 by Charles Seliger, Vice-president and artist/designer for the company, is preserved at the Cooper-Hewitt National Design Museum in New York and the National Museum of American History, Archives Center in Washington. The Commercial Decal Company collection is closely associated with the decorative arts, especially pottery and china ornamentation. The company produced ceramic decals using mostly the screen technique - a process of projecting an art work onto a silk, polyesters or woven wire cloth screen coated with the photosensitive emulsion. It supplied companies such as Ridgewood Fine China, Haviland, Homer Laughlin, Corning and Medalta (Alberta). The other large collection of transfers preserved in North America consists of the archival documents of the Palm Brothers Decalcomania Company, the oldest American transfer producer, the first incorporated in 1868. It is kept at the Cincinnati Museum Center. This very rich collection - 16 cubic feet of records - contains correspondence, business and financial statements, sample decals as well as information on the company’s customers and the competition. The Palm Brothers produced decorative decals for vast range of manufacturers: Ford Motor Company, The Edison Phonograph Co., McLaughlin Carriage Co., Oshawa, Ont.; and Lakefield Canoe Building and Manufacturing Co., Lakefield, Ont., to name a few. Nonetheless, in the context of the study of the history of industrial arts and graphic design as an expression of the corporate identity, the Canada Science and Technology Museum’s collection of transfers remains a rare and important resource. (Image 31)
Captions:
Image 1. A 19th century coach decorated with gold leafs and the Royal Coat of Arms. Artifact no. 680879
Image 2. A beautifully decorated Midland Railway of Canada steam locomotive no. 15 "Adolph Hugel" type 4-4-0, c.1880. CN002546.
Image 3. Transfer ornamented pottery, made by Creil et Montereau, c. 1870. Artifact no. 871483.
Image 4. Backing of a decal can reveal the application technique, in this case a duplex method, which allowed to separate the paper after the image was firmly place on the surface. Artifact no. 750129.325
Image 5. Letters and numbers produced by the Canada Decalcomania Co. for the Canadian National Railway. Artifact no. Ak114.9 630
Image 6. The coat of arms of the Buenos Aires Central South Railway Co. Ltd., Tearne & Sons. Artifact no. 750129.425
Image 7. By 1890 sewing machines were commonly decorated with gold leaf and transfers. Artifact no. 921234
Image 8. A clock made by Pequegnat, Arthur Clock Co., c. 1904 is decorated with a transfer image of King Edward. Artifact no. 750282
Image 9. Transfers offered an inexpensive method of ornamenting household items such as this 19th century cylinder player. Artifact no. 760134
Image 10. Samuel Tearne advertisement.
Image 11. Coat of arms of the city of Chesterfield. Artifact no. 750129.347
Image 12. Instructions for the coat of arms of the Lancaster Company from Buenos Aires disclose handwritten description of colours (“shaded gray & green; gold; green line”), and dated approvals of changes to the master design. Artifact no. 750129.389
Image 13. A rare coat of arms of the P&O Co. The extensive design and the blend of colours and shades was expensive to reproduce and difficult to transfer, and the arms were quickly abandoned by the company. Artifact no. 750129.406.
Image 14. Proofs of number 2 prepared by Tearne for the Great Eastern Railway. Artifact no. AK 114.320
Image 15. Letters FCT, a monogram of the Taltal Railway Co., printed in revers in order to be transferred right side up. Artifact no. 750129.364
Image 16. Tearne transfers coated with gold leaf. Artifact no. AK 114.854
Image 17. An image of the Bombay, Baroda & Central India Railway coat of arms printed directly onto a simplex paper. A single layer made the process of transferring difficult and the paper was later replace by a duplex or double paper, which was easily separated from the image. Artifact no. AK114.318
Image 18. A duplex transfer with the monogram of the King George VI. Artifact no. 750129.388
Image 19. A transferred monogram placed on the Royal Train during the 1939 Royal Tour of Canada. CN 003710
Image 20. A china set used at the Chauteau Laurier was decorated with transfers depicting the CN logo. CNX15146
Image 21. The coat of arms of the Great Western Railway. Artifact no. 750129.361
Image 22. The coat of arms of the Great Southern Railways. Artifact no. 750129.636
Image 23. The coat of arms of the County Donegal Railways Joint Committee. Artifact no. 750129.351
Image 24. A decal made by the Canada Decalcomania Co. for Pierre Thibault Ltée, a manufacturer of fire trucks. Artifact no. 990132
Image 25. A bull’s head made for Wagon Repairers Ltd. in 1938 and used on the company’s vans. Artifact no. 750129.
Image 26. Armorial in character trademark of the Birmingham Carriage and Wagon Company. The transfer was produced by Tearne in 1925. Artifact no. 750129.316
Image 27. The image of a galloping horse on a deep golden background made by Tearne & Sons for John Marston & Co. reveals the skills of the Tearne’s craftsmen, but also reflects Victorian taste for exaggerated ornamentation. Artifact no. 750129.412
Image 28. A face of a woman designated the “Ladies only” railway cars. Artifact no. 750129.418
Image 29. Highly decorated sleeper car, c. 1890. CN37399.
Image 30. A crest made by Tearne for SS Yoma, 1928. Artifact no. 750129.315
Image 31. This simple monogram of the Great Western Railway, which replaced more elaborate design in mid-1930s, became a universal symbol of the company placed on its railway stock, uniforms, timetables and promotional material. Artifact no. AK114.416
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- nancy c university of southern california
- lecture summer 2011 art history teaching resources
- collection profiles industrial transfers and the art of
- hcol acu blogs
- historic buildings desk guide
- critical theory since plato the twentieth century and after
- fo guang shan buddha memorial center treasures of the
- key ideas and details homepage u s national
- ahis 250 modernity and difference critical approaches to
- archeology for the non archeologist