CUSTOMER:
| | | | | |
|Customer: |Bristol Donald Company | |End User: |New Jersey Coop |
| |50 Roanoke Ave | |Body Type: |2-Ton |
| |Newark NJ 07105 | |Chassis: |NA |
| | | | | |
|Contact: |Robert Greeley | | | |
|Phone: | | | | |
|Mobile: |non listed | | | |
|Email: |sales@ | | | |
| | | | | |
|Quote Date: | 2/16/2018 | |Notes: | |
|Quote valid until: | 3/18/2018 | | | |
|Salesperson: | Gary Hibma | | | |
| | Quote Number: GKH1064 | | | |
|QTY |DESCRIPTION |NOTES |UNIT PRICE | AMOUNT |
| |Maintainer Service Body With Crane | | | |
| | | | | |
| |-------- Maintainer Body -------- | | | |
|1 |Light Bar Mount (Aluminum), front of body, center deck width, tube frame, no panel | |$774 |$774 |
| |Includes paint or protective spray coating to match body layout | | | |
|1 |Light Bar Mount (Aluminum), front of body, center deck width, tube frame, with slotted| |$893 |$893 |
| |panel | | | |
| |Includes paint or protective spray coating to match body layout | | | |
|1 |Tall Tower Crane reinforcement for MTS 1 or 2 ton service body (up to 75,000 ft*lb) | |$837 |$837 |
| |NOTE: For individual crane equipment & accessory items ie. adj. boom saddle, outrigger| | | |
| |pkgs., body leveling pkgs., hyd. pkgs. to operate a crane or other hyd. drive | | | |
| |components - Contact Factory | | | |
|1 |Short Tower Crane reinforcement for MTS 1 or 2 ton service body (up to 30,000 ft*lb) | |$1,070 |$1,070 |
| |NOTE: For individual crane equip. & accessory items ie. adj. boom saddle, outrigger | | | |
| |pkgs., body leveling pkgs., hyd. pkgs. to operate a crane or other hyd. drive | | | |
| |components-Contact Factory | | | |
|1 |Short Tower Crane reinforcement for MTS 1 or 2 ton service body (up to 45,100 ft*lb) | |$1,174 |$1,174 |
| |NOTE: For individual crane equip. & accessory items ie. adj. boom saddle, outrigger | | | |
| |pkgs., body leveling pkgs., hyd. pkgs. to operate a crane or other hyd. drive | | | |
| |components-Contact Factory | | | |
|1 |Short Tower Crane reinforcement for MTS 1 or 2 ton service body (up to 75,000 ft*lb) | |$1,934 |$1,934 |
| |NOTE: For individual crane equip. & accessory items ie. adj. boom saddle, outrigger | | | |
| |pkgs., body leveling pkgs., hyd. pkgs. to operate a crane or other hyd. drive | | | |
| |components-Contact Factory | | | |
|1 |Factory Installation of body on a chassis |To be added to what ever body |$1,673 |$1,673 |
| | |is picked | | |
| | | | | |
| |-------- Compartment Equipment & Accessories -------- | | | |
|1 |Pressurized Storage System (PSS), 2-blowers with filters | |$494 |$494 |
|1 |Feet of Master Compartment Locking System for steel body. Spring loaded with padlock |Per foot includes both sides |$65 |$65 |
| |guards for both side packs | | | |
|1 |Oxy / Act bottle storage w/ratchet strap, vents, "J" hks. & reinforced floor | |$226 |$226 |
|1 |Oxy / Act compartment to be set up for 3 bottles, in lieu of 2 | |$112 |$112 |
|1 |Reel, Oxy / Act dual hose reel, spring rewind with 1/4" x 50' (Grade T) hose | |$991 |$991 |
| |Includes pigtails to tank area or compartment outlet & plug / any length over 10' | | | |
| |requires additional charge. | | | |
| | | | | |
| |-------- Hydraulic Power Package -------- | | | |
|1 |Closed center LS hydraulic power package, includes air shift PTO (requires chassis air| |$5,841 |$5,841 |
| |system) | | | |
| |Includes: pump, std oil reservoir with in-tank filter, vented fill cap, sight gauge | | | |
|1 |Closed center LS hydraulic COMPACT-HIGH EFFICIENCY power package, includes air shift | |$6,355 |$6,355 |
| |PTO (requires chassis air system) | | | |
| |Includes: pump, oil cooler, 7-13 gallon oil reservoir with in-tank filter, vented fill| | | |
| |cap, sight gauge | | | |
| |Note: Saves 418 lbs. vs. std. power package, can not be used in apps that require the | | | |
| |displacement of oil (cylinder, tool circuit) | | | |
|1 |Large closed center load-sensing hydraulic power package, includes air shift PTO | |$7,106 |$7,106 |
| |(requires chassis air system) | | | |
| |Includes: large pump, large oil reservoir with in-tank filter, vented fill cap, sight | | | |
| |gauge | | | |
| |NOTE: For high GPM hydraulic requirements - Consult Factory | | | |
|1 |Open center hydraulic power package, includes air shift PTO (requires chassis air | |$5,241 |$5,241 |
| |system) | | | |
| |Includes: pump, std oil reservoir with in-tank filter, vented fill cap, sight gauge. | | | |
| |NOTE: The Open-Center hydraulic system allows operation of only a single hydraulic | | | |
| |component at a time. | | | |
| |Multi-component operation requires a Closed-Center system and is not available on some| | | |
| |chassis configurations. Contact factory for details. | | | |
|1 |Large open center hydraulic power package, includes air shift PTO (requires chassis | |$6,804 |$6,804 |
| |air system) | | | |
| |Includes: Vane pump, Large oil reservoir w/ in-tank filter, vent fill cap, sight | | | |
| |gauge. | | | |
| |NOTE: This power package is specifically for a Ford 6-speed auto transmission, | | | |
| |providing approximately 23 gpm. | | | |
| |NOTE: This Open-Center hydraulic system allows multiple operation of hydraulic | | | |
| |components at a time. | | | |
|1 |Hydraulic cooling package, high efficiency bar/plate design, low-medium GPM flow |Required with large hydraulic |$1,327 |$1,327 |
| |rating |package | | |
| |Includes a high temperature shutdown switch with indicator light | | | |
|1 |Miller EnPak A60HGE Power Package with control panel |No PTO hydraulic system |$33,454 |$33,454 |
| |24.8HP Kubota diesel engine, utilizes chassis 12-volt battery & fuel (requires two |required | | |
| |auxiliary fuel ports) | | | |
| |Includes engine block heater with 120V plug-in | | | |
| |Crane remote integration: Not Included / Quoted separately | | | |
| |Hydraulic Pump: Closed Center /Load Sensing (10 gpm), Includes hydraulic reservoir w/ | | | |
| |120V heater & auxiliary cord | | | |
| |Air Compressor: Rotary screw 60 CFM @ 100 PSI (Air tank required, quoted separately) | | | |
| |Generator: 6000 Watt, GFI outlets (1) 120V, (1) 240V Remote-mounted | | | |
| |Welder: Not Included, See Maxstar welder options | | | |
| |Inverter: EnVerter - 2400 Watt, with (1) 120V GFI outlet | | | |
| |Jumpstart / Charger: Not included / quoted separately | | | |
| |White housing; 21"W x 30"T x 47"L, 832 lbs | | | |
| |Note: Specify mounting location: | | | |
| |-Center deck location may require a removable panel for protection | | | |
| |-If mounted near fixed walls, requires a minimum of 36" width for air flow and panel | | | |
| |access | | | |
| |-If inside an enclosure, requires AO-03606 for ventilation | | | |
|1 |Air tank - 17 gallon - (Pressure rating of 200 psi) / 16" diameter (000012) | |$620 |$620 |
| |Includes moisture drain | | | |
|1 |Add a fuel port & suction tube to chassis fuel tank, for engine driven equipment to | |$495 |$495 |
| |use the chassis as a fuel source | | | |
| |(Necessary when chassis fuel tanks come in without 2 additional ports for fuel suction| | | |
| |and return) | | | |
| |Consult factory: Generally not required for F550, Ram 5500 & Kenworth T270 / T370, but| | | |
| |likely | | | |
| |required for Ford F650 / F750, International, Freightliner and Peterbilt chassis | | | |
|1 |Planetary winch in lieu of worm gear on H7024 / H6520 crane | |$1,554 |$1,554 |
| |Note: Increases winch cable length to 140 ft | | | |
|1 |Removable divider panel in center deck | |$293 |$293 |
|1 |Heater, electric, 120 volt, fan forced, 1,000 / 1,500 watt (014892) - w/ male plug | |$156 |$156 |
| |NOTE: May require an additional 120 volt plug-in wired to power source | | | |
|1 |Crane remote control hook-up (tethered or wireless), for engine-driven power packages | |$247 |$247 |
|1 |Mounting angles | |$244 |$244 |
|1 |Extension cord 25' for Miller Maxstar / Multimatic welders, 6-50-P/R 250volt rating | |$340 |$340 |
|1 |Miller Maxstar welding lead cables w/ clamp and stinger, 15' of #2 cable | |$229 |$229 |
|1 |Miller Maxstar 210-STR #907682 with 240V plug; (Arc gouging capable) NOTE: Includes | |$3,332 |$3,332 |
| |10ft. power cord and plug. | | | |
| |Capable of TIG, Stick, and Air carbon Arc welding | | | |
|1 |Miller Multimatic 200 welder (MIG, TIG, or Stick weld) #907518, without optional TIG | |$2,800 |$2,800 |
| |welding kit | | | |
| |NOTE: Includes 10ft. power cord and plug for 120V or 240V, includes 13ft cable with | | | |
| |electrode holder & 10ft work cable with ground clamp, | | | |
| |includes 10ft Bernard Q150 MIG gun | | | |
| |NOTE: Not capable of Arc Gouging | | | |
|1 |Vanair Air N Arc I300 Power Package with control panel |No PTO hydraulic system |$31,042 |$31,042 |
| |24.8HP Kubota diesel engine, utilizes chassis 12-volt battery & fuel (requires two |requiresd | | |
| |auxiliary fuel ports) | | | |
| |Includes cold weather package with 12 Volt switch in cab | | | |
| |Crane remote integration: Not Included / Quoted separately | | | |
| |Hydraulic Pump: Closed Center /Load Sensing (8 gpm), Includes hydraulic reservoir w/ | | | |
| |120V heater & auxiliary cord | | | |
| |Air Compressor: Rotary screw 40 CFM @ 100 PSI (Includes 4-gallon air tank & | | | |
| |remote-mounted moisture drain) | | | |
| |Generator: 6800-Watt, GFI outlets (4) 120V, (1) 240V mounted in control panel (not | | | |
| |pure-sine/not recommended for battery charging items such as laptops, cell phones, | | | |
| |etc) | | | |
| |Welder: 300 AMP high frequency, CC/DC & CV/DC (Welder leads sold separately) | | | |
| |Inverter: Not included / quoted separately | | | |
| |Jumpstart / Charger: 300 AMP 12V battery charger with 12V/24V boost (Jumpstart cables | | | |
| |sold separately) | | | |
| |Note: White housing; 21"W x 33"T x 47"L, 910 lbs | | | |
| |Note: Specify mounting location: | | | |
| |-Center deck location may require a removable panel for protection | | | |
| |-If inside an enclosure, requires AO-03606 for ventilation | | | |
|1 |Air tank - 17 gallon - (Pressure rating of 200 psi) / 16" diameter (000012) | |$620 |$620 |
| |Includes moisture drain | | | |
|1 |Add a fuel port & suction tube to chassis fuel tank, for engine driven equipment to | |$495 |$495 |
| |use the chassis as a fuel source | | | |
| |(Necessary when chassis fuel tanks come in without 2 additional ports for fuel suction| | | |
| |and return) | | | |
| |Consult factory: Generally not required for F550, Ram 5500 & Kenworth T270 / T370, but| | | |
| |likely | | | |
| |required for Ford F650 / F750, International, Freightliner and Peterbilt chassis | | | |
|1 |Planetary winch in lieu of worm gear on H7024 / H6520 crane | |$1,554 |$1,554 |
| |Note: Increases winch cable length to 140 ft | | | |
|1 |Heater, electric, 120 volt, fan forced, 1,000 / 1,500 watt (014892) - w/ male plug | |$156 |$156 |
| |NOTE: May require an additional 120 volt plug-in wired to power source | | | |
|1 |Jump start cables (25ft) for welder / gen. with jumpstart option | |$409 |$409 |
|1 |Crane remote control hook-up (tethered or wireless), for engine-driven power packages | |$247 |$247 |
|1 |Mounting angles | |$244 |$244 |
|1 |~Cables, Welder leads, w/ clamp and stinger, 50' of 1/0, 300 amps | |$552 |$552 |
| | | | | |
| |-------- Crane Equipment & Accessories -------- | | | |
|1 |EH4520ST Electric / Hydraulic Crane 4,500 lb max capacity (20,000 ft*lb) with | |$17,433 |$17,433 |
| |hydraulic extend boom 10'-20' | | | |
| |#019995 Crane includes proportional wireless remote with back-up cable, holder with | | | |
| |storage sensor, indicator light & external antenna, planetary winch, level gauge, | | | |
| |A2B, overload system, holding valves, load block with non-live-swivel safety hook & | | | |
| |master on/off switch. | | | |
| |Items not included but are required are: Additional deep cycle battery and separator /| | | |
| |isolator or low voltage shut-off switch | | | |
| |Ship-out note: Ship-out EH cranes include a 3/4" spacer plate (021507) to allow for | | | |
| |bolt clearance, not required with Maintainer body | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
| |Maintainer inventory cranes are pre-painted Z1 Ford Oxford white | | | |
|1 |Separate / Isolate the auxiliary battery(s) from chassis batteries. | |$235 |$235 |
| |NOTE: "Add deep cycle batteries" must be selected if this option is desired to | | | |
| |separate auxiliary batteries from chassis batteries | | | |
|1 |(1) deep cycle battery (includes tie down, pad & cover) | |$571 |$571 |
|1 |H4520ST Crane 4,500 lb max capacity (20,000 ft*lb) with hydraulic extend boom 10'-20' | |$16,852 |$16,852 |
| |Chassis Open Center or Closed Center hydraulic system required (not included) | | | |
| |#019994 Crane includes proportional wireless remote with back-up cable, holder with | | | |
| |storage sensor, indicator light & external antenna, planetary winch, level gauge, | | | |
| |A2B, overload system, holding valves, & load block with non-live-swivel safety hook. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |EH5520ST Electric / Hydraulic Crane 5,500 lb max capacity (30,000 ft*lb) with | |$17,841 |$17,841 |
| |hydraulic extend boom 10'-20' | | | |
| |#019999 Crane includes proportional wireless remote with back-up cable, holder with | | | |
| |storage sensor, indicator light & external antenna, planetary winch, level gauge, | | | |
| |A2B, overload system, holding valves, load block with non-live-swivel safety hook & | | | |
| |master on/off switch. | | | |
| |Items not included but are required are: Additional deep cycle battery and separator /| | | |
| |isolator or low voltage shut-off switch | | | |
| |Ship-out note: Ship-out EH cranes include a 3/4" spacer plate (021507) to allow for | | | |
| |bolt clearance, not required with Maintainer body | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
| |Maintainer inventory cranes are pre-painted Z1 Ford Oxford white | | | |
|1 |Separate / Isolate the auxiliary battery(s) from chassis batteries. | |$235 |$235 |
| |NOTE: "Add deep cycle batteries" must be selected if this option is desired to | | | |
| |separate auxiliary batteries from chassis batteries | | | |
|1 |(1) deep cycle battery (includes tie down, pad & cover) | |$571 |$571 |
|1 |H5520ST Crane 5,500 lb max capacity (30,000 ft*lb) with hydraulic extend boom 10'-20' | |$17,260 |$17,260 |
| |Chassis Open Center or Closed Center hydraulic system required (not included) | | | |
| |#019998 Crane includes proportional wireless remote with back-up cable, holder with | | | |
| |storage sensor, indicator light & external antenna, planetary winch, level gauge, | | | |
| |A2B, overload system, holding valves, & load block with non-live-swivel safety hook. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |H6520TT Crane 6,500 lb max capacity (38,000 ft*lb) with hydraulic extend hex-boom |Tall or short tower crane |$17,961 |$17,961 |
| |12'-20' |19,500 GVW recommended | | |
| |Crane includes a true independent proportional wireless remote, holder with storage | | | |
| |sensor, indicator light & external antenna, ACC, gear winch, crane hour meter, | | | |
| |engine start/stop, A2B, overload system, holding valves & load block with | | | |
| |non-live-swivel safety hook. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires paint Charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |H7024TT Crane 7,000 lb max capacity (45,100 ft*lb) with hydraulic extend hex-boom |Tall or short tower crane |$19,560 |$19,560 |
| |11'-24' |19,500 GVW required | | |
| |Crane includes a true independent proportional wireless remote, holder with storage | | | |
| |sensor, indicator light & external antenna, ACC, gear winch, crane hour meter, | | | |
| |engine start/stop, A2B, overload system, holding valves & load block with | | | |
| |non-live-swivel safety hook. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |H10025TT Crane 10,000 lb max capacity (75,000 ft*lb) with hydraulic extend hex-boom |Tall or short tower 11' body |$25,868 |$25,868 |
| |13'-25' |26,000 GVW min | | |
| |Crane includes a true independent proportional wireless remote, holder with storage | | | |
| |sensor, indicator light & external antenna, ACC, planetary winch, crane hour meter, | | | |
| |engine start/stop, A2B, overload system, holding valves & load block with | | | |
| |non-live-swivel safety hook. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |H10034TT Crane 10,000 lb max capacity (75,000 ft*lb) with hydraulic extend hex-boom |Tall or short tower requires |$32,075 |$32,075 |
| |15'-34' |14' body & 33,000 GVW chassis | | |
| |Crane includes a true independent proportional wireless remote, holder with storage | | | |
| |sensor, indicator light & external antenna, ACC, planetary winch, crane hour meter, | | | |
| |engine start/stop, A2B, overload system, holding valves & load block with | | | |
| |non-live-swivel safety hook. | | | |
| |Note: Crane typically requires 120" C-A min Chassis w/ 33K GVWR | | | |
| |Note: requires 90,000 ft/lb outriggers with 57" extension | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |H12025TT Crane 12,000 lb max capacity (90,000 ft*lb) with hydraulic extend hex-boom |Tall tower only, 14' body and |$31,746 |$31,746 |
| |13'-25' |33,000 GVW required | | |
| |Crane includes a true independent proportional wireless remote, holder with storage | | | |
| |sensor, indicator light & external antenna, ACC, planetary winch, crane hour meter, | | | |
| |engine start/stop, A2B, overload system, holding valves & load block with | | | |
| |non-live-swivel safety hook. | | | |
| |Note: Crane typically requires 108" C-A min. and additional front outriggers | | | |
| |recommended for increased side-lifting capability. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |H14025TT Crane 14,000 lb max capacity (90,000 ft*lb) with hydraulic extend hex-boom |Tall tower only, 14' body and |$33,614 |$33,614 |
| |13'-25' |33,000 GVW required In some | | |
| |Crane includes a true independent proportional wireless remote, holder with storage |cases front outriggers may be | | |
| |sensor, indicator light & external antenna, ACC, planetary winch, crane hour meter, |needed | | |
| |engine start/stop, A2B, overload system, holding valves & load block with | | | |
| |non-live-swivel safety hook. | | | |
| |Note: Crane typically requires 120" C-A min. and additional front outriggers | | | |
| |recommended for increased side-lifting capability. | | | |
| |Paint note: | | | |
| |Ship-out crane-only: Requires additional paint charge | | | |
| |Crane installed on body: No additional paint charge unless different color than body | | | |
|1 |Install EH crane on body - includes boom saddle, crane remote storage pocket | |$981 |$981 |
|1 |Install hydraulic crane on body - includes boom saddle, and valve well | |$1,337 |$1,337 |
| | | | | |
| |-------- Outriggers & Accessories -------- | | | |
|1 |Outriggers for cranes up to 45,100 ft*lb, Manual crank up/down rear outrigger (2), and| Can be used with electric and |$2,098 |$2,098 |
| |Manual extend in/out on crane side only |hydraulic cranes works with | | |
| | |EH4520/ H4520, EH5520/ H5520, | | |
| | |H6520, & H7024 cranes | | |
|1 |Outriggers for cranes up to 45,100 ft*lb, hydraulic up/down rear outriggers (2) with |Hydraulic cranes only, needed |$3,792 |$3,792 |
| |manual extend in/out on crane side (30" extend) |with 1111-15, H6520, & H7024 | | |
| | |cranes | | |
|1 |Hydraulic extend in/out outrigger - one side, in lieu of manual |Use only with hydraulic |$1,108 |$1,108 |
| | |outriggers | | |
|1 |Outriggers for cranes up to 75,000 ft*lb, hydraulic up/down rear outriggers (2) with |Required with H10025 short or |$5,416 |$5,416 |
| |hydraulic extend in/out on crane side (48" extend) |tall tower crane | | |
|1 |Outriggers for cranes up to 90,000 ft*lb, hydraulic up/down rear outriggers (2) with |Required with H10034, H12025, &|$6,309 |$6,309 |
| |hydraulic extend in/out on crane side (57" extend) |H14025 cranes | | |
| |Required with H10034, H12025, H14025 Cranes | | | |
|1 |Outriggers for front of body, hydraulic up/down outriggers (2) with manual extend |Might be needed with H14025 |$3,792 |$3,792 |
| |in/out on crane side (30" extend) |crane consult dealer | | |
| | | | | |
| |-------- Chassis Equipment & Accessories -------- | | | |
|1 |Spring or spacer leveling package added to one side of chassis suspension (2-Ton) |Needed for chassis with spring |$224 |$224 |
| | |suspension | | |
|1 |Add additional air leveling valve for crane body for chassis w/ air suspension. |Need with air suspension |$512 |$512 |
| | |chassis if only one (1) is | | |
| | |ordered on chassis | | |
|1 |Add charge to standard PTO package for electric-over-hydraulic required on chassis |Need on Ford F-650, & F-750 |$1,122 |$1,122 |
| |with automatic transmission.(Ford F450-F550, F650-F750 & Ram 4500-5500) | | | |
|1 |Adder hydraulic kit needed with an air compressor on chassis with gas, propane, or CNG| |$556 |$556 |
| |engine | | | |
| |Soft shift control block spool (013724), coil, connector and bleed down orifice | | | |
| |For “Propane / CNG engines (lower HP) may reduce hyd. performance, and potentially | | | |
| |cause engine surging/stalling.” | | | |
|1 |Electric brake controller | |$339 |$339 |
|1 |Electronic engine speed control - computer set - electronic engine | |$153 |$153 |
| | | | | |
| |-------- Welder / Generator / Inverter / Power Equipment -------- | | | |
|1 |Mounting angles |For inverter or welder each |$244 |$244 |
|1 |Inverter-Light Duty-2500 watt, Modified Sine Wave, #011529 | |$882 |$882 |
| |NOTE: Wired to chassis batteries, Mounted front of body, Customer to verify | | | |
| |compatibility with electronic items | | | |
|1 |Inverter-Heavy Duty-2400 watt, w/ 350 & 400 amp fuse & holders. Extra battery, | |$4,165 |$4,165 |
| |separator, & battery box | | | |
| |#009422 Mounted toward front of body, Pure Sine Wave (Batteries) | | | |
| |NOTE: Customer to verify compatibility with electronic items | | | |
|1 |Inverter 4000 watt w/ 350 & 400 amp fuse & holders. Extra battery, separator, & | |$4,669 |$4,669 |
| |battery box / heavy duty usage / for batteries | | | |
| |Ultimate power UP12/4000SD | | | |
|1 |Inverter-Light Duty-5000 watt, Modified Sine Wave, #013838 | |$1,263 |$1,263 |
| |NOTE: Wired to chassis batteries, Mounted front of body, Customer to verify | | | |
| |compatibility with electronic items | | | |
|1 |Adder for mounting inverter at rear of service body (without auxiliary battery) In | |$527 |$527 |
| |lieu of in cab or front of service body | | | |
|1 |Adder for mounting inverter at rear of service body (with auxiliary battery) In lieu | |$318 |$318 |
| |of in cab or front of service body | | | |
|1 |Miller Bobcat 225 gas (Kohler) #907498. GFCI outlets | |$5,458 |$5,458 |
| |NOTE: 28"H (33" to top of exhaust) x 20"W x 40.5"D / 485 lbs. | | | |
| |NOTE: Includes installation | | | |
|1 |Miller Bobcat 250 gas (Kohler) #907500 GFCI outlets (018541) | |$6,353 |$6,353 |
| |NOTE: 28"H (33"H to exhaust) x 20"W x 40.5"D / 501 lbs. | | | |
| |NOTE: Includes installation | | | |
|1 |Miller Trailblazer 325 gas (Kohler w/ EFI) #907754 | |$8,120 |$8,120 |
| |NOTE: 28"H (33"H to exhaust) x 20"W x 40.5"D / 460 lbs. | | | |
| |NOTE: Includes installation | | | |
|1 |Miller Trailblazer 325 diesel (Kubota) GFCI outlets 907755001 | |$13,224 |$13,224 |
| |NOTE: 28"H (34.38"H to exhaust) x 20"W x 45.38"D / 650 lbs. | | | |
| |NOTE: Includes installation | | | |
|1 |Plumb engine-driven equipment to chassis fuel tank (Includes booster pump) | |$475 |$475 |
| |Note: Requires chassis fuel tank to have an auxiliary port for a suction line | | | |
|1 |~Cables, Welder leads, w/ clamp and stinger, 50' of 1/0, 300 amps | |$552 |$552 |
| | | | | |
| |-------- Air Compressor Equipment & Accessories -------- | | | |
|1 |Vanair Reliant RC40 reciprocating hydraulic driven 40 CFM air compressor with cover | |$7,688 |$7,688 |
| |40 CFM @ 100 PSI / 40 CFM @ 150 PSI w/ 17 gallon air tank with moisture drain & | | | |
| |integral hydraulic oil cooler | | | |
| |Includes cold weather package (oil cooler thermal bypass) | | | |
| |Note: White housing | | | |
| |Note: Hydraulic requirement = 12 gpm | | | |
|1 |VMAC Predatair 40 CFM rotary screw hydraulic driven air compressor w/ white cover | |$9,131 |$9,131 |
| |40 CFM @ 150 psi with 17 gallon air tank with moisture drain & integral hydraulic oil | | | |
| |cooler. | | | |
| |Includes control panel, mounted near body's switch panel | | | |
| |Note: Hydraulic requirement = 14 gpm (May require large pump kit, not included), | | | |
| |Cold weather package included (cooler bypass), additional oil warming valve available | | | |
| |(open center only) | | | |
| |24"L x 16.5"W x 18"H, 162 lbs | | | |
|1 |Cold weather package (oil warming valve) for VMAC Predatair compressors (open center | |$903 |$903 |
| |only) | | | |
|1 |Vanair Reliant 60 CFM rotary screw hydraulic driven air compressor w/ white cover | |$11,622 |$11,622 |
| |(RS85) | | | |
| |60 CFM @ 150 psi with 17 gallon air tank with moisture drain & integral hydraulic oil | | | |
| |cooler. | | | |
| |Includes a high temperature shutdown switch with indicator light | | | |
| |Includes cold weather package with 12 volt switch in cab | | | |
| |Note: Hydraulic requirement = 14.2 GPM. May require a large pump kit (not available on| | | |
| |some chassis configurations) | | | |
| |Multi-component operation may be limited, contact factory for details | | | |
|1 |Vanair Reliant 85 CFM rotary screw hydraulic driven air compressor w/ white cover | |$11,622 |$11,622 |
| |(RS85) | | | |
| |85 CFM @ 125 psi with 17 gallon air tank with moisture drain & integral hydraulic oil | | | |
| |cooler. | | | |
| |Includes a high temperature shutdown switch with indicator light | | | |
| |Includes cold weather package with 12 volt switch in cab | | | |
| |Note: Hydraulic requirement = 19.9 GPM. May require a large pump kit (not available on| | | |
| |some chassis configurations) | | | |
| |Multi-component operation may be limited, contact factory for details | | | |
|1 |Vanair V2 Multi-drive system PTO Driven - Air Comp / Hyd pump mount | |$19,164 |$19,164 |
| |Note: does not include generator | | | |
| |Rotary screw air comp. capable of 125-185 cfm @ 100psi w/ control panel, psi gauge, | | | |
| |hour meter and oil temp | | | |
| |**Note: A specific control panel location must be determined to finalize an order, | | | |
| |please note location | | | |
| |Note: Package excludes: Reservoir, custom chassis speed control, PTO & driveline | | | |
| |Note: Must be quoted with "open center" hydraulic package (Use AO-02192 speed control)| | | |
| |Note: May require additional drive-line due to chassis component interference, | | | |
| |Chassis drop-ship to compressor manufacturer may be required, | | | |
| |review chassis details with Maintainer Factory | | | |
|1 |PTO driveline or adaptor - std. displacement hydraulic pump |Required w/ Vanair V2 |$431 |$431 |
|1 |Air shift PTO |Required w/ Vanair V2 |$1,055 |$1,055 |
|1 |Gas driven Ingersoll-Rand air compressor - 13HP Honda, 25 CFM @175 PSI (Maximum) |For use with no hydraulic |$6,612 |$6,612 |
| |Model 2475F13GH on 30 gallon air tank with moisture drain, Includes electric start, |system | | |
| |and installation | | | |
| |Remote-mounted controls and mounting angles are sold separately (44Lx27Wx41H) 450 | | | |
| |pounds | | | |
|1 |Diesel driven Quincy air compressor - 10HP Yanmar, 22 CFM @175 PSI (Maximum) |For use with no hydraulic |$10,424 |$10,424 |
| |Model QT7.5-10Y-30H, Includes 30 gallon air tank with moisture drain, electric start, |system | | |
| |and installation | | | |
| |Remote-mounted controls and mounting angles are sold separately (46Lx26Wx41H) 545 | | | |
| |pounds | | | |
|1 |Hose reel access out rear compartment | |$257 |$257 |
|1 |Air accessory package - 1/2" X 50' Filter / lubricator / regulator, spring rewind | |$1,032 |$1,032 |
| |reel, hose & ball stop | | | |
|1 |Air accessory package - 3/8" X 30' (Hosetract Reel) Filter / lubricator / regulator, | |$751 |$751 |
| |spring rewind reel, hose & ball stop | | | |
|1 |Air accessory package - 3/4" X 50' Filter / lubricator / regulator, spring rewind | |$1,391 |$1,391 |
| |reel, hose & ball stop | | | |
|1 |Air accessory package - 1" X 50' Filter / lubricator / regulator, spring rewind reel,| |$1,573 |$1,573 |
| |hose & ball stop | | | |
|1 |Air tank - 17 gallon - (Pressure rating of 200 psi) / 16" diameter (000012) |May be needed if not included |$664 |$664 |
| |Includes moisture drain |in air compressor package | | |
| | | | | |
| |-------- Lighting / Electrical Equipment & Accessories -------- | | | |
|1 |Exterior 12v LED flood light (2010-Raw / 1350-Effective Lumens) |Each |$184 |$184 |
|1 |Exterior 12v LED flood light pkg. 1-perm / 1-remote (2010-Raw / 1350-Effective Lumens)| |$278 |$278 |
|1 |~Strobe Lightheads, L.E.D, oval, amber, recessed, 6.5" x 2.25" (pair) | |$370 |$370 |
|1 |~Strobe Lightheads Low profile L.E.D, rectangular, amber, external mount, Whelen TIR3 | |$375 |$375 |
| |3.5" x 1.13" (2x-1 ea front corner) (012002 or 012513) | | | |
|1 |Interior 12 v. LED strip light (can be used in O/A compartments) |Each compartment |$115 |$115 |
|1 |Traffic Advisor, Whelen model TA-837, installed | |$1,381 |$1,381 |
|1 |~Light Bar, Whelen amber Lo-Profile LED mini light bar, Model MC16PA (#019873) 2-3/8"| |$583 |$583 |
| |H x 16-1/2" W x 7-3/4" D | | | |
| | | | | |
| |-------- Painting Equipment & Accessories -------- | | | |
|1 |Feet of unit painted urethane "White" color. Not a base coat/clear coat or Metallic |Per foot of body |$214 |$214 |
| |Note: Includes protective spray covering on compartment fronts, bottom door frames, | | | |
| |outside area around wheel wells, outer vertical outrigger tubes, rear bumper face & | | | |
| |step surface | | | |
| |Note: Due to variations in OEM paint products and application methods, Maintainer | | | |
| |cannot guarantee a perfect paint match on color | | | |
| |Note: For colors other than white additional charges will be required | | | |
|1 |Feet of unit painted urethane "Base Coat/Clear Coat - Metallic" |Per foot of body for colors |$412 |$412 |
| |Note: Includes protective spray covering on compartment fronts, bottom door frames, |other than white | | |
| |outside area around wheel wells, outer vertical outrigger tubes, rear bumper face & | | | |
| |step surface | | | |
| |Note: Due to variations in OEM paint products and application methods, Maintainer | | | |
| |cannot guarantee a perfect paint match on color | | | |
|1 |Feet of Protective Spray Covering - MTS - cargo center deck, compartment tops & sides,|Per foot of body |$167 |$167 |
| |front bulkhead, tail gate & extension, bumper and/or workbench area | | | |
|1 |Protective Spray Covering: Cab guard | |$648 |$648 |
|1 |Protective Spray Covering: Inside of wheel wells, single axle, ILO undercoating | |$629 |$629 |
| | | | | |
| |-------- Roll-Out drawer and Tray Equipment & Accessories -------- | | | |
|1 |~DuaLock (5) drawer aluminum set 18"W x 18"D x (5)-4"H, (300 lb. cap. per drawer) | |$1,267 |$1,267 |
| |Includes top shelf | | | |
| |Overall height 30", #013225, Installed | | | |
| |(1) Permanent Front-to-Back divider, (4) Removable Side-to-Side Dividers | | | |
|1 |~DuaLock (7) drawer aluminum set 29"W x 18"D x (1)-7", (3)-5", (3)-3"H, (300 lb. cap. | |$1,984 |$1,984 |
| |per drawer) Includes top shelf | | | |
| |overall height 41.50", #020017, Installed | | | |
| |(2) Permanent Side-to-Side Dividers, Removable Front-to-Back Dividers | | | |
|1 |Bolt Bin (LD) 18 drawers w/ drop-in dividers, 34"W x 13"H x 18"D (002938) | |$612 |$612 |
|1 |Bolt Bin (HD) 16 drawers - 8H x 2W (16"Wx32"Hx18"D) - #009228 Drawers are (4"x8"x18")| |$1,586 |$1,586 |
| |w/ drop-in dividers | | | |
|1 |Bolt Bin (HD) 16 drawers - 4H x 4W (32"Wx16"Hx18"D) - #011564. Drawers are (4"x8"x18")| |$1,621 |$1,621 |
| |w/ drop-in dividers | | | |
|1 |Bolt Bin (LD) 18 drawers w/ drop-in dividers, 17"W x 21.5"H x 12"D | |$627 |$627 |
|1 |Bolt Bin (LD) 9 drawers w/ drop-in dividers, 17"W x 11"H x 12"D, Model 004-95 | |$441 |$441 |
| |(020448) | | | |
| | | | | |
| |-------- Center Deck Equipment & Accessories -------- | | | |
|1 |3 -section aluminum sliding cover for MTS center deck (up to 10.5 ft length) w/ | |$3,296 |$3,296 |
| |bi-folding door | | | |
| |*Not designed to walk on / On TT Cranes does not extend to rear of body (360 lb. | | | |
| |approx. wt.) | | | |
| |*Standard slide-top has a 2" riser and allows for 34.75" height clearance above | | | |
| |center-deck floor | | | |
|1 |4 -section aluminum sliding cover for MTS center deck (11 ft and longer) w/ bi-folding|Needed on 14' bodies |$3,805 |$3,805 |
| |door | | | |
| |*Not designed to walk on / On TT Cranes does not extend to rear of body (510 lb. | | | |
| |approx. wt.) | | | |
| |*Standard slide-top has a 2" riser and allows for 34.75" height clearance above | | | |
| |center-deck floor | | | |
|1 |Add-on for "Hinge-Up" sliding cover w/ gas spring lift | |$857 |$857 |
|1 |Riser for slide-top, in addition to the standard 2" slide-top riser | |$399 |$399 |
|1 |Cargo Cover, Tarp & Bow System / 11 ft long, retracts to 38" (approximate) | |$2,851 |$2,851 |
| |Retractable roller guide system, includes rope and tie-downs | | | |
| |Estimated weight = 292 lbs. | | | |
|1 |Cargo Cover, Tarp & Bow System / 14 ft long, retracts to 44" (approximate) | |$3,238 |$3,238 |
| |Retractable roller guide system, includes rope and tie-downs | | | |
| |Estimated weight = 349 lbs. | | | |
|1 |Flush mount "D" ring tie-downs in bed floor #003217, each |Each |$44 |$44 |
|1 |Removable divider panel in center deck | |$293 |$293 |
| | | | | |
| |Lube Equipment and Accessories | | | |
|1 |0-25 gallon ALUMINUM tank, 8D design, equipped with filtered fill cap, suction screen,| |$1,083 |$1,083 |
| | | | | |
| |sight gauge, shut-off valve on tank suction line, installed / spring mounted w/ rubber| | | |
| |pad | | | |
|1 |26-50 gallon ALUMINUM tank, 8D design, equipped with filtered fill cap, suction | |$1,301 |$1,301 |
| |screen, | | | |
| |sight gauge, shut-off valve on tank suction line, installed / spring mounted w/ rubber| | | |
| |pad | | | |
|1 |51-100 gallon ALUMINUM tank, 8D design, equipped with filtered fill cap, suction | |$1,504 |$1,504 |
| |screen, | | | |
| |sight gauge, shut-off valve on tank suction line, installed / spring mounted w/ rubber| | | |
| |pad | | | |
|1 |Air Kit Oil, 5:1 ratio Samson pump, 2-3 GPM delivery (Varies with oil type) | |$2,263 |$2,263 |
| |Hannay 1/2" X 50' spring rewind reel, with rollers (019647/019646) | | | |
| |high-flow non-drip non-metered rigid dispenser (019593) | | | |
|1 |Air Kit - Oil / Anti-freeze Evacuation Diaphragm pump 1" x 30' | |$4,383 |$4,383 |
| |0-15 GPM delivery w/ hydraulic, 10wt or 20wt @ 60 degrees F. | | | |
| |0-8 GPM delivery w/ 30wt, 50wt or 90 wt @ 60 degrees F. | | | |
| |1" x 30' spring reel, with rollers (017401), 4-way control & suction screen, control | | | |
| |valve & regulator (Not for water / solvent) | | | |
| |Includes tank full sensor with indicator light, buzzer, pump shut-down, and bypass | | | |
| |switch | | | |
| |212°F Maximum operating temperature | | | |
|1 |Hydra Kit, Oil - Turolla pump (small displ.) | |$2,577 |$2,577 |
| |Up to 7 GPM delivery w/ hydraulic, 10wt or 20wt @ 60 degrees F. | | | |
| |Up to 4 GPM delivery w/ 30wt, 50wt or 90 wt @ 60 degrees F. | | | |
| |Hannay 1/2" X 50' spring reel, with rollers & high-flow non-drip rigid dispenser | | | |
|1 |Hydra Kit Anti-freeze - (Non-Corrosion resistant kit) | |$3,699 |$3,699 |
| |8-Roller Stainless Pump (018578) 0-10 GPM delivery | | | |
| |Hannay 1/2" X 50' spring rewind reel, with rollers | | | |
| |Non-metered dispenser | | | |
|1 |Hydra Kit #5 Oil Evacuation - Commercial-Shearing pump (large displ.) 1" x 30' | |$4,724 |$4,724 |
| |0-10 GPM delivery w/ hydraulic, 10wt or 20wt @ 60 degrees F. | | | |
| |0-4 GPM delivery w/ 30wt, 50wt or 90 wt @ 60 degrees F. | | | |
| |Hannay 1" x 30' spring reel, with rollers, 4-way control & suction screen | | | |
| |Includes tank full sensor with indicator light, buzzer, pump shut-down, and bypass | | | |
| |switch | | | |
| |212°F Maximum operating temperature | | | |
|1 |Air Kit, 120# Grease Kit (16 gallon) Graco 50:1 pump | |$3,669 |$3,669 |
| |Includes: control valve, regulator & oiler, drum cover, follow plate & tie down | | | |
| |Hannay 3/8" X 50' spring rewind reel, with rollers, high pressure dispenser with | | | |
| |swivel | | | |
| | | | | |
| |-------- Rear Bumper & Accessories -------- | | | |
|1 |26" steel workbench bumper with 2-side storage compartments | |$3,258 |$3,258 |
| |Includes two mounting pockets for an optional vise / grinder mounting plate | | | |
| |Includes a stainless steel rear bumper shell | | | |
| |Note: Hitch and trailer plug to be quoted separately | | | |
|1 |26" steel workbench bumper with recessed step on one side, 2 side storage compartments| |$4,081 |$4,081 |
| |Includes a single mounting pocket for an optional vise / grinder mounting plate | | | |
| |Includes: 2 grab handles and strip light for recessed step safety, transverse bar | | | |
| |storage (6.5 ft long, flush with floor), (doors on both sides). | | | |
| |Includes a stainless steel rear bumper shell | | | |
| |Note: Hitch and trailer plug to be quoted separately | | | |
|1 |~Transverse bar storage compartment in workbench bumper flush to the floor | |$246 |$246 |
|1 |Class IV hitch receiver - 2" receiver - rated at 1,500 lbs. vert. 10,000 lbs. MGTW | |$158 |$158 |
| |Note: customer is responsible to verify tow rating of chassis and available GVWR/GCWR | | | |
| |remaining after loading of body and all other items. | | | |
|1 |Trailer plug-in 7-prong flat blade #007486 (RV style) | |$113 |$113 |
|1 |Trailer plug-in (6 prong / round pin) | |$82 |$82 |
| | | | | |
| |-------- Miscellaneous Equipment & Accessories -------- | | | |
|1 |Vise / grinder removable mounting plate HD, includes drain slots in plate | |$181 |$181 |
|1 |~Vise, 6.5" Jaw Width, 6.5" Jaw Opening- Wilton Tradesman Model 1765 | |$903 |$903 |
|1 |Single axle wheel well extensions (3-piece bolt-on),aluminum w/ protective spray. | |$391 |$391 |
| |Note: Kit includes flares for both sides of body | | | |
| | | Quote Total: |$575,024 |
| | |Discount: |$0 |
| | |Total Due: |$575,024 |
The following options may be added:
|QTY |DESCRIPTION |NOTES |UNIT PRICE |AMOUNT |
| | | | | |
Maintainer Terms and Conditions:
o All prices are F.O.B. Sheldon, IA & in USD; delivery charges to be determined. This quote does not include any applicable local, state or (F.E.T) federal taxes. Payment in full is required on delivery unless other terms are agreed upon prior to sale.
o Ex-factory delivery is 150-210 days after receipt of order with full order information subject to prior sales and chassis availability.
o Maintainer reserves the right to make changes and/or substitute components and product is subject to change without notice; Maintainer is not responsible for any Local, State, Federal or other regulations that maybe pertinent to quote/order.
o The information contained in this quote, and all supporting documentation is confidential and may only be used by Maintainer, our dealer and/or the customer listed on this quote.
o We assume no liability for damage due to theft, vandalism, fire, weather, disaster, or damage due to gradual deterioration or inherent defect in such property.
o We assume no liability for damage any kind during the storage of your chassis or parts on our premises while awaiting modification or installation. The storage location of the property shall be determined by Maintainer in its discretion.
o Exception to above is when directly attributable to our own gross negligence in moving or modifying chassis or parts, and in that event only to the extent of the wholesale used value of the chassis or parts as of the date of storage.
o Thank you for your interest in Maintainer's products and the opportunity to quote you. If you have any questions please feel free to contact us at (800) 831-8588.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- west creek financial customer reviews
- what is customer relationship management
- customer relationship management system for small business
- free customer tracking software
- frontline aesop customer service number
- frontline support customer service
- importance of customer relationship management
- list of customer service responsibilities
- frontline education customer service num
- small business customer relationship management
- the importance of customer relationship
- the role of customer relationship management