Department of Enterprise Services



APPENDIX C

SPECIFICATIONS

ANNOUNCEMENT

This document contains garment and product specifications pertaining to Categories

One through Four for this Invitation for Bid. You do not need to return this document

with your bid submittal.

1

CATEGORY ONE – CUSTOM UNIFORMS

1 TROUSER SIZE SPECIFICATION

The purpose of this specification is to obtain quality workmanship on uniform trousers for all season wear for the WSP, CVD, and DFW. Trousers shall be available for long and short waisted personnel and construction will be appropriate for women where applicable, i.e., waist and lengths to include darts where necessary.

KNEE AND BOTTOM MEASUREMENTS

| | |

|NECK |ARM SIZES |BODY LENGTH |CHEST SIZE |

|14 |30,31,32,33,34 |S,M,L |34 |

|14.5 |30,31,32,33,34,35 |S,M,L |36 |

|15 |30,31,32,33,34,35 |S,M,L |38 |

|15.5 |30,31,32,33,34,35,36 |S,M,L |40 |

|16 |31,32,33,34,35,36 |S,M,L |42 |

|16.5 |31,32,33,34,35,36,37 |S,M,L | |

|17 |31,32,33,34,35,36,37,38 |S,M,L | |

|17.5 |31,32,33,34,35,36 |S,M,L | |

|18 |32,33,34,35,36,37,38 |S,M,L | |

2 Shirt, Uniform – Trimmed, Short Sleeve

MATERIAL:

To be as specified below with Kaumograph running full length of material at regular intervals. Yoke lining to be minimum 140 count rayon.

WEAVE: Tropical

WEIGHT: 11-11.5 Oz per linear yard

FIBER CONTENT: 55% Dacron Polyester; 45% Wool

PLY YARN: 3-Ply Warp and Filling

BREAKING STRENGTH: 105 Lbs in the Warp; 85 Lbs in the Filling

CONSTRUCTION: 55 ends per inch; 46 picks per inch

FIBER LENGTH: Wool 3-3.5 inches average minimum; Polyester 3 Inches minimum

DYE PROCEDURE: Piece Dyed

KAUMOGRAPH: Back face of fabric must be stamped with mill trademark.

FOR COLLAR, BODY, POCKETS, BADGE TABS AND SLEEVES:

WSP:

Raeford 573-563, French Blue or equal, 55% Dacron, 45% Wool, 11 – 11.5 oz.

CVD:

Raeford 573-585, Gray or equal, 55% Dacron, 45% Wool, 11-11.5 oz.

DFW:

Raeford 571-193, Silver Tan or equal, 55% Dacron, 45% Wool, 11-11.5 oz.

Shirt, Uniform – Trimmed, Short Sleeve Continued

FOR SHOULDER STRAPS, POCKET FLAPS:

WSP:

Hamburger 651-8 or equal, 45% Wool, 55% Dacron, 14 oz., Royal Blue

CVD:

Hamburger 651-Black or equal, 45% Wool, 55% Dacron 14 oz, Black

DFW:

Hamburger 651-42 or equal, 45% Wool, 55% Dacron 14 oz, Forest Green.

All thread used in construction shall be of best quality vat-dyed, mercerized, left twist, color to match material specified.

COLLAR:

Sport collar attached with single bone button of matching color. Collar shall be one piece and measure 3-1/4" at collar point. For woman, collar points shall measure approximately 2 7/8" long at points. Collar shall be 1-7/8" high in back when folded. Collar shall be of double construction, interlined with # 285 Mello Press, "Chix" or equal. Collar shall have permanent sewn-in stays of "Mylar" or equal.

SHOULDER STRAPS:

Materials shall be as specified above in "MATERIALS".

Style and dimensions as specified herein. Contrasting shoulder straps of Royal Blue. Asymmetrical shape topstitched with ¼” double needle stitching.

Shoulder straps shall be set on top of the double needle Sleeving seam in a thread color to match. There shall be a horizontal buttonhole eyelet sewn on each shoulder to correspond to the strap buttonholes.

There shall also be a protective piece of cloth sewn on the inside of the shirt under each eyelet to protect the wearer from metal button toggles.

Points of the shoulder straps to be tacked to the shoulders at the point. Strap to measure approximately 2” at sleeve tapering to 1 3/8” and set not more than ½” from folded collar.

POCKETS:

The two outside breast patch pockets shall be 6" deep and 5-5/8" wide and shall have a 1-1/2" vertical box pleat through the center.

Bottom corners of pockets shall be mitered and double-stitched at the sides and bottom and shall have a 1/2" hem at the top.

A pencil compartment, 1-1/2" finished width, stitched to the bottom with opening through flap shall be made on the right hand side of the left pocket.

Each pocket shall have a flap 2-1/2" deep and 5-7/8" wide which shall be made of the material as specified under "MATERIALS" depending upon the agency requesting the shirts.

An eyelet for a metal button shall be placed in a horizontal position, centered 1-1/4" below the top of the pocket, with a corresponding vertical buttonhole in the flap. The top of the flap shall be 5/8" above the top of the pocket.

For Women:

Breast pockets should be raised 1/2" - 1" and badge holder should be adjusted accordingly. *Pocket width to be 5" wide and 5" deep. Pencil opening shall be 1 ¼”

Shirt, Uniform – Trimmed, Short Sleeve Continued

BODY:

Shall be form fitting with a straight yoke at a minimum of 3" deep from the bottom of collar. Length of shirt body - 34" minimum for size 16 shirt and smaller; 35" minimum for size 16-1/2 shirt and larger. Measurement to be from bottom of collar. French-type open facing 3" wide cut in single piece, single stitched 1/4". Facing to extend from collar seam to bottom hem, fully tacked at bottom hem.

For All Shirts:

Interlining of self fabric 1" wide, extending from collar seam to within 4" of the bottom hem for reinforcement of eyelets. Eyelet holes bound through shirt front and through self fabric reinforcement. Self fabric reinforcement set in the edge of seam.

Women's shirts:

There are to be two darts in the front and two darts in the back. Length of shirt body is 29” for all sizes

SLEEVES:

Armholes shall be full cut, especially in large sizes.

Sleeves are to be straight and whole, to have a 3/4" hem and to finish approximately 9" long from shoulder seam.

For Women:

Arm holes need to be tailored in without affecting the fullness of the body. Female troopers and officers wear bullet proof vests that necessitates the fullness.

BADGE TABS:

One (1) tunnel-type badge tab 1-3/4" long and 1" wide with a 1/4" wide tunnel shall be centered and spaced 1" above the top of the left pocket flap.

Badge tab shall be reinforced with a cloth support on the inside of the shirt approximately 7" long by 1-1/4" wide, fastened at one end under the left shoulder seam so as to support the front of the shirt when a heavy badge is attached.

Shirt, Uniform – Trimmed, Short Sleeve Continued

BUTTONS:

WSP and CVD

Each shirt shall have one bone collar button to match material specified, eyelets and buttonholes for five (5) metal uniform buttons and two (2) matching bone buttons on the shirt front, each spaced at no less than 3-3/4" intervals beginning at the collar button.

In addition, each shirt shall have two (2) metal uniform button eyelets and corresponding buttonholes on each cuff, one on each pocket and one on each shoulder strap.

The single collar button and the two bottom buttons on the Shirt front shall be 1/2" bone, furnished by the Contractor and securely sewn to the shirt.

The metal uniform buttons will be regulation "George Washington Head", Waterbury #14297, size 5/8" diameter with metal fasteners and will be furnished and attached by the Washington State Patrol and CVD after delivery of the shirts. A sample brass button with fastener will be furnished the contractor to assist in designing the eyelets and buttonholes.

All eyelets for the metal buttons on the shirt front shall be cut and finished on the horizontal and the corresponding buttonholes shall be on the vertical.

Shirt, Uniform – Trimmed, Short Sleeve Continued

DFW:

Each shirt shall have on matching bone collar button, eyelets and buttonholes for six (6) matching bone buttons on the shirt front, each spaced at no less than 3-3/4" interval beginning at the collar button. In addition, each shirt shall have one (1) metal uniform button eyelet on each pocket and one (1) on each shoulder strap with corresponding buttonholes.

The single collar button and the 6 buttons on the shirt front shall be 1/2" bone, furnished by the Contractor and securely sewn to the shirt.

The metal uniform buttons will be regulation "George Washington Head", Waterbury #14297, size 5/8" diameter with metal fasteners and will be furnished and attached by Fish and Wildlife after delivery of the shirts. A sample brass button with fastener will be furnished to the Contractor to assist in designing the eyelets and buttonholes. All eyelets for the metal buttons on the shirt front shall be cut and finished on the horizontal and the corresponding buttonholes shall be on the vertical. All metal button fasteners shall be covered with cloth facings.

For Women:

Buttons-distance between buttons are to be narrower than men’s resulting in 7 buttons (6 with holes and 1 at neck with loop) to avoid gaping. Last button to be finished by sewing one eyelet hole under plastic button of the shirt to utilize the hole for a fifth metal button.

All metal buttons fasteners shall be covered with cloth facings.

GENERAL:

All seams and edges shall be double felled (Two rows of stitching). All shirts in stock sizes shall be made with 6" drop, in accordance with list of neck and sleeve sizes furnished by the requesting agency with the balance of the shirt to be made in proportion. Tailoring shall be of first-class workmanship and subject to the approval of the requesting agency. Sample will be furnished to requesting agency for approval before commencement of run. Each shirt need to have five holes for attaching metal buttons on the button-side of the front of all shirts. Sewn (1) eyelet hole under the top button of the two plastic buttons of the shirt to utilize the hole for a fifth metal button. Shirt length to be available for longer shirt tails. Placket in front of shirt will be 1-1/2" wide. For each neck size, shirt body sizes shall be available in small, medium and large.

|UNIFORM SHIRT, LONG SLEEVE (MEN’S) |UNIFORM SHIRT, LONG SLEEVE (WOMEN’S) |

|NECK |ARM SIZES |BODY LENGTH |NECK |ARM SIZES |CHEST SIZE |BODY LENGTH |

|14 |30,31,32,33,34 |S,M,L |13 |30,31,32,33,34 |34,36,38 |S,M,L |

|14.5 |30,31,32,33,34,35 |S,M,L |13.5 |30,31,32,33,34 |34,36,38 |S,M,L |

|15 |30,31,32,33,34,35 |S,M,L |14 |30,31,32,33,34 |36,38,40,42 |S,M,L |

|15.5 |30,31,32,33,34,35,36 |S,M,L |14.5 |30,31,32,33,34 |36,38,40,42 |S,M,L |

|16 |31,32,33,34,35,36 |S,M,L |

|16.5 |31,32,33,34,35,36,37 |S,M,L |

|17 |31,32,33,34,35,36,37,38 |S,M,L |

|17.5 |31,32,33,34,35,36 |S,M,L |

|18 |32,33,34,35,36,37,38 |S,M,L |

3 UNIFORM SHIRT SIZE SPECIFICATION

The purpose of this specification is to obtain quality materials and workmanship in Uniform Shirts for personnel of the State Patrol, CVD and Department of Fish And Wildlife. Shirt sizes will be as follows. However, there will be times when non-standard sizes are required. Shirts in non-standard sizes will be conveyed to contractor at time of order placement.

4 SHIRT, UNIFORM – TRIMMED, LONG SLEEVE

MATERIAL:

To be as specified below with Kaumograph running full length of material at regular intervals. Yoke lining to be minimum 140 count rayon.

WEAVE: Gabardine

WEIGHT: 11-11.5 Oz per linear yard

FIBER CONTENT: 55% Dacron; 45% Wool

PLY YARN: 3-Ply Warp and Filling

BREAKING STRENGTH: 105 Lbs in the Warp; 85 Lbs in the Filling

CONSTRUCTION: 55 ends per inch; 46 picks per inch

FIBER LENGTH: Wool 3-3.5 inches average minimum; Polyester 3 inches minimum

DYE PROCEDURE: Piece Dyed

KAUMOGRAPH: Back face of fabric must be stamped with mill trademark

FOR COLLAR, BODY, POCKETS, BADGE TABS AND SLEEVES:

WSP:

Raeford 521-563, French Blue or equal, 55% Dacron, 45% Wool, 11 – 11.5 oz.

CVD:

Raeford 521-585, Gray or equal, 55% Dacron, 45% Wool, 11-11.5 oz.

DFW:

Raeford 571-193, Silver Tan or equal, 55% Dacron, 45% Wool, 11-11.5 oz.

For shoulder straps, pocket flaps and cuffs:

WSP:

Hamburger 651-8 or equal, 45% Wool, 55% Dacron, 14 oz., Royal Blue.

Shirt, Uniform – Trimmed, Long Sleeve

CVD:

Hamburger 651-Black or equal, 45% Wool, 55% Dacron 14 oz, Black.

DFW:

Hamburger 651-42 or equal, 45% Wool, 55% Dacron 14 oz, Forest Green.

All thread used in construction shall be of best quality vat-dyed, mercerized, left twist, color to match material specified.

COLLAR:

Regular military style, attached with a single bone collar button.

Collar shall be 1-3/4" high in back, tapering to 1" in front, so as not to be irritating on neck.

Collar shall have 3-1/4" points, 1/2" tie opening, and 3" spread when buttoned.

Collar shall be interlined with #285 Mello-Press,"Chix" or equal.

Collar and yoke shall be lined with minimum 140 count rayon.

Collar shall have permanent, sewn-in stays on "Mylar" or equal.

SHOULDER STRAPS:

Materials shall be as specified above in "MATERIALS".

Style and dimensions as specified herein. Contrasting shoulder straps of Royal Blue. Asymmetrical shape topstitched with ¼” double needle stitching.

Shoulder straps shall be set on top of the double needle Sleeving seam in a thread color to match. There shall be a horizontal buttonhole eyelet sewn on each shoulder to correspond to the strap buttonholes.

There shall also be a protective piece of cloth sewn on the inside of the shirt under each eyelet to protect the wearer from metal button toggles.

Points of the shoulder straps to be tacked to the shoulders at the point. Strap to measure approximately 2” at sleeve tapering to 1 3/8” and set not more than ½” from folded collar.

POCKETS:

The two outside breast patch pockets shall be 6" deep and 5-5/8" wide and shall have a 1-1/2" vertical box pleat through the center.

Bottom corners of pockets shall be mitered and double-stitched at the sides and bottom and shall have a 1/2" hem at the top.

A pencil compartment, 1-1/2" finished width, stitched to the bottom with opening through flap shall be made on the right hand side of the left pocket.

Each pocket shall have a flap 2-1/2" deep and 5-7/8" wide which shall be made of the material as specified under "MATERIALS" depending upon the agency requesting the shirts.

An eyelet for a metal button shall be placed in a horizontal position, centered 1-1/4" below the top of the pocket, with a corresponding vertical buttonhole in the flap.

The top of the flap shall be 5/8" above the top of the pocket.

For Women:

Breast pockets should be raised 1/2" - 1" and badge holder should be adjusted accordingly. *pocket width to be 5" wide and 5" deep. Pencil opening shall be 1 ¼”1.

BODY:

Shall be form fitting with a straight yoke at minimum of 3"

deep from the bottom of the collar, extending up to the collar and well over the shoulder width.

Length of shirt body -34" minimum for size 16 shirt and smaller; 35" minimum for size 16-1/2 shirt and larger. Measurement to be from bottom of collar. Tails of shirt to be finished as a dress shirt. (Gussets between front and back panels between sideseams are not required). The shirt shall have a double-stitched boxed front.

Shirt, Uniform – Trimmed, Long Sleeve

Women's shirts:

There are to be two darts in the front and two darts in the back. Length of shirt body is 29” for all sizes as measured above.

SLEEVES:

The sleeves shall have double elbows, pear shaped, extending 10-1/2" from the top of the cuff on size 33" length. Larger sizes must be in proportion. Do not double elbows on Fisheries sleeves.

The width of the double elbows shall be from 2" to front of placket seams to seams of sleeves; the vent shall be a minimum 3-1/2" opening, finished from top of cuff.

Sleeve material shall be pleated into cuff with one small pleats from button side of placket of seam and not gathered.

Armholes shall be full cut, especially in larger sizes.

Shirt, Uniform – Trimmed, Long Sleeve Continued

For Women:

State Patrol and Department Of Fish and Wildlife- arm holes need to be tailored in without affecting the fullness of the body. Female troopers and officers wear bullet proof vests that necessitates the fullness.

BADGE TABS:

One (1) tunnel-type badge tab 1-1/2" long and 1" wide with a 1/4" wide tunnel shall be centered and spaced 1" above the top of the left pocket flap.

Badge tab shall be reinforced with a cloth support on the inside of the shirt approximately 7" long by 1-1/2" wide, fastened at one end under the left shoulder seam so as to support the front of the shirt when a heavy badge is attached.

CUFFS:

Shall be made of trim material as specified in "MATERIALS" as indicated for agency requesting shirts.

Cuffs shall be 3" wide, square-cornered and shaped.

Cuffs shall be double thickness with no stiffening material inserted.

Cuffs shall be 9" in circumference on shirts to size 16 and 10" in circumference in size 16-1/2 and larger, measured from center of button to center of buttonhole.

WSP and CVD

Each cuff shall have 2 horizontal eyelets with two corresponding buttonholes evenly spaced.

DFW

Each cuff shall have 2 buttons with two corresponding buttonholes evenly spaced.

Cuffs shall be double-stitched at top and bottom.

Shirt, Uniform – Trimmed, Long Sleeve

BUTTONS:

WSP and CVD

Each shirt shall have one bone collar button to match material specified, eyelets and buttons for four (4) metal uniform buttons and two (2) matching bone buttons on the shirt front, each spaced at no less than 3-3/4" intervals beginning at the collar button.

In addition, each shirt shall have two (2) metal uniform button eyelets and corresponding buttonholes on each cuff, one on each pocket and one on each shoulder strap.

The single collar button and the two bottom buttons on the Shirt front shall be 1/2" bone, furnished by the Contractor and securely sewn to the shirt.

The metal uniform buttons will be regulation "George Washington Head", Waterbury #14297, size 5/8" diameter with metal fasteners and will be furnished and attached by the Washington State Patrol and CVE after delivery of the shirts. A sample brass button with fastener will be furnished to the contractor to assist in designing the eyelets and buttonholes. All eyelets for the metal buttons on the shirt front shall be cut and finished on the horizontal and the corresponding buttonholes shall be on the vertical.

For Women:

Buttons- distance between buttons need to be narrower than the men’s resulting in 7 buttons (6 with holes and 1 at neck with loop) to avoid gaping. Last button to be finished by sewing one eyelet hole under plastic button of the shirt to utilize the hole for a fifth metal button.

All metal buttons fasteners shall be covered with cloth facings.

DFW

Each shirt shall have one matching bone collar button, Eyelets and buttonholes for six (6) matching bone buttons on the shirt front, each spaced at no less than 3-3/4" interval beginning at the collar button.

In addition, each shirt shall have one (1) metal Uniform button eyelet on each pocket and one (1) on each shoulder strap with corresponding buttonholes and two (2) bone buttons on each cuff.

The single collar button and the 6 buttons on the shirt Front shall be 1/2" bone, furnished by the Contractor and securely sewn to the shirt.

The metal uniform buttons will be regulation "George Washington Head", Waterbury #14297, size 5/8" diameter with metal fasteners and will be furnished and attached by Fish and Wildlife after delivery of the shirts. A sample brass button with fastener will be furnished and the Contractor to assist in designing the eyelets and buttonholes.

All eyelets for the metal buttons on the shirt front shall be cut and finished on the horizontal and the corresponding buttonholes shall be on the vertical. All metal button fasteners shall be covered with cloth facings.

GENERAL:

All seams and edges shall be double felled(Two rows of stitching).

All shirts in stock sizes shall be made with 6" drop, in accordance with list of neck and sleeve sizes furnished by the requesting agency with the balance of the shirt to be made in proportion.

Tailoring shall be of first-class workmanship and subject to the approval of the requesting agency.

Sample will be furnished to requesting agency for approval before commencement of run.

Each shirt need to have five holes for attaching metal buttons on the button-side of the front of all shirts. Sewn (1) eyelet hole under the top button of the two plastic buttons of the shirt to utilize the hole for a fifth metal button.

Shirt length to be available for longer shirt tails.

Placket in front of shirt will be 1-1/2" wide.

For each neck size, shirt body sizes shall be available in small, medium and large.

BREECHES, UNIFORM, MOTORCYCLE

MATERIALS:

To be as specified below with Kaumograph running full length of material at regular intervals. Yoke lining to be minimum 140 count rayon.

WEAVE: Elastique

WEIGHT: 16-16.5 Oz per linear yard

FIBER CONTENT: 55% Dacron Polyester; 45% Wool

PLY YARN: 2-Ply Warp and Filling

BREAKING STRENGTH: 210 Lbs in the Warp;135 Lbs in the Filling

CONSTRUCTION: 125 ends per inch; 85 picks per inch

FIBER LENGTH: Wool 3-3.5 inches average minimum; Polyester 3Inches minimum

DYE PROCEDURE: Stock Dyed

KAUMOGRAPH: Back face of fabric must be stamped with mill Trademark

WSP:

Raeford 646-114, French Blue or equal, 45% Wool, 55% Dacron 16 - 16-1/2 oz.

Trim - Raeford 8247-33194 Royal Blue or equal14 – 14.5 Oz.

This item is custom tailored. Measurements will be provided at time of order

STYLE:

½ Peg Style, with full Cavalry Double Seat, with Square Corners extended along inseam to below knee area. Double knee reinforcement extending down from crotch and then across the knee to below knee area. Zippers on bottoms of legs, Hip size to be compatible with waist.

POCKETS:

Two (2) full top pockets and two (2) hip pockets with flaps to button. All pockets secured at corners with heavy bartacking. Pockets to be of #250 all cotton drill, stitched-turned-stiched. For women: Rear with extra room in seat.

SEAMS:

Inseam and backseam to be stitched with heavy flexible thread using double lock stitch. Waist seam to have two (2) inch outlet and all raw edges to be merged. One and three quarter inch (1-3/4”) strips of fabric (3934-4659) shall be sewn full length of the outseam to extend from waist seam to bottom.

BELT TUNNELS:

Seven (7) one and one-quarter inch (1-1/4) wide belt tunnels sewed into waistband seam, finished wide enough to accommodate a two inch (2” belt).

WAISTBAND:

The trouser will be made with a waistband system designed to provide the wearer with a more comfortable and better fitting trouser. The waistband shall be constructed using the "closed method" and shall measure 2" wide when finished. The waistband closure shall be accomplished with a crush proof hook and eye. The hook and eye shall be reinforced with stays made of a non-woven fabric that are anchored by the topstitching for the fly facing and curtain. This topstitching must be to the top of the waistband. The waistband must be topstitched 1/16" below the waistband seam for added strength. The top portion of the inside of the waistband is to be consisting of the same fabric as used for pocketing (70% polyester 30% cotton - minimum 80 X 62 (+/-) 2 count). The fabric is to be cut on the bias for maximum comfort. To be 1 3/4" wide and to finish 1 1/8" wide after construction.

Upper waistband curtain to be inner lined with stretch Ban-Rol canvas. This canvas fabric consists of a warp of 47 ends of texturized nylon and a fill of 34 ends of 750-denier polyester monofilament. The woven fabric is coated with latex, which completely encapsulates all yarns. This finish canvas fabric weighs 12.0 oz/yd2. The canvas will be cut 1 3/8" monofilaments running vertically and have a 10% stretch. The bottom portion of the waistband curtain will be a blend of 32% nylon, 38% polyester, 18% rubber (3 strands) 11% lycra and 1% acrylic woven 1 7/8" wide and to finish a minimum 1 5/8" wide. To have a minimum of 40% stretch characteristics. The waistband curtain and trim shall be “harmonizing” cadet blue.

Note: In a performance stretch waistband, the upper and lower portion of the band will perform different functions.

The upper portion should allow a comfort fit at the waist when bending or sitting, and must maintain a crisp, clean appearance at the outer waistband. This part of the band will stretch 10% and be firm enough to prevent waistband rollover.

The bottom portion of the waistband stretches over the hip to give support to the lower back and abdomen. In addition, this high stretch portion of the band should constantly be pressed up by the hips, preventing the slack from slipping down while being worn, even if heavy keys, change, or other items are carried in the pockets or on the belt.

FLY:

Heavy duty Talon or Equal Best Grade Zipper Fly with two (2) button waistband and one (1) button inside fly.

For Women:

Breeches should be available for long and short waisted personnel. Construction will be appropriate for women where

applicable. Waist and lengths to include dart where necessary.

CATEGORY TWO - BATTLE DRESS UTILITY (BDU) UNIFORMS

1 BDU PANT:

Black, 60% Cotton/ 40% Poly Twill, Sewn to Military Specification MIL-T-44047E, Six Pockets, Four with Button Flaps, Fused Pocket Flaps, Four Button Fly, Double-Reinforced Seat and Knee, Adjustable Waist Tab with 4 Bar Tacks. Propper International F520112001 or equal

2 BDU 2-POCKET SHIRT:

Black, 60% Cotton/ 40% Poly Twill, Bellows pockets with Drain Holes, Double-Reinforced Elbows, Felled Side Seam and Sleeves, Adjustable Sleeve Buttons, Button Down Shoulder Epaulets. Propper International F545212001 or equal.

3 TACTICAL DRESS SHIRT:

Black, Short Sleeve, 60% Cotton/ 40% Poly Twill, Set on Front Placket, Banded Collar with Sewn-In Collar Stays, Box Pleated Front Pockets with Flaps, Enclosed Badge Tab, Button Down Shoulder Epaulets. Reinforced with Box (x) Stitching. Propper International F530112001 or equal

4 CATEGORY THREE – ALL WEATHER GEAR

5 MEDIUM WEIGHT

Shell Fabric:

Gortex shell, Zepel water and stain repellant finish with an original spray rating of 90 or 60/40

MFG/Model: Olympic Attack Jac 241 or equal

Lining:

Lining fabric is cotton/nylon with a water repellant finish, wide front facings for front stability

Inside Pockets:

Two specially designed inside holster/equipment pockets (left and right side) constructed of 200 denier heavy duty oxford nylon. Pockets are "holster" shaped, 11" deep with a barrel extension caught in the bottom band and side seam of the lining to securely hold a weapon in place. Pocket opening is 7" wide and secured with two pieces of velcro approximately 2" x 1/2" sewn at the corner of each side of the opening to allow easy access to weapons and equipment.

Interlining:

Front, collar, pocket facing and cuffs are interfaced with a non-woven material

Front:

Front closure is #5 twenty two inch heavy duty two way delrin departing zipper

Collar:

permanent collar is made of two plies of shell fabric plus an interlining. The interlining is stitched to the undercollar. Stitched collar stand to help the collar fold at the proper location. Four inch collar points are well shaped and symmetrical

Front pockets:

two large eight inch long vel handwarmer pockets, the pocket vel is constructed of shell material and is folded to finish two inches wide. Each pocket is approximately 9.5" deep. Bartacked at each corner for reinforcement. Pocketing is heavy duty flannel.

Bottom band:

Bottom band is constructed of two plies of shell fabric finish 2.5" wide. The bottom band facings are approximately 8.5" long and are sewn to the elasticized bottom which is constructed with heavy duty elastic inserted between the folded fabric at the sides. Elastic is stretched and stitched with two threads.

Sleeves:

Sleeves are one piece and set into the armhole. Sleeves are finished with a knit wristlets of stretch nylon. Oversize one inch shoulder pads are provided to give the jackets a neat, well constructed appearance and to help conceal and balance the weight of the weapons or equipment carried in the inside pockets

Back:

Back has a full rain shed yoke with a two inch turned up design to conceal the hidden ID flap system. The yoke is fully lined with nylon and there is an additional yoke facing of nylon. Three velcro sets on the yoke facing that match the location of corresponding sets on the shell to securely close the rain shed yoke. The ID flaps which match corresponding velcro sets on the yoke linings to hold the flaps in place when not in use. Back pull down flap measures approximately 16" long x 6.5" wide. A separate panel designed to screened and sewn onto the flap is16" long by five inches wide

Fronts:

Fronts have full rain shed yokes with a two inch turn up designed to conceal the hidden ID flap system. Each yoke is fully lined with nylon and there is an additional yoke facing of nylon. One velcro set on each yoke facing that match the location of the corresponding set on the shell to securely close the rain shed yoke on each side when the ID flaps are concealed. Matching sets of velcro are provided on the underside of each ID flaps which matches corresponding velcro sets on the yoke linings to hold the flaps in place when not in use. The left pull down flap measures approximately four inches long by six inches wide and is designed to hold a cloth shield or emblem. The right pull down flap measures 7.5" wide by 4.5" long. A separate panel designed to be screened and sewn onto the right flap is four inches long x 7.5" wide.

Stitching and Reinforcement:

Zipper, buttons and pockets are bar tacked. Heavy duty spun polyester thread is used throughout the garment.

Length and fit:

Garment is 27" long and is tailored so that it can be worn over a sweater, Loner or Ballistic vest

Care:

home wash or dry clean.

6 All Weather Jacket

The jacket shall be waist length with a split waistband to allow for side vent zippers. There shall be a split front and back, a two-way zipper under a double fly front, permanent epaulets, and two, 2 way inverted pleated pockets. The sleeves shall be 3 pieces to form a box armhole to allow maximum freedom of movement and shall have access zippers for emblem customization without penetrating the lining. The shell will be waterproof and breathable. The jacket will feature a fully removable lining with a non-pilling fleece body and nylon sleeves. The liner will be fully insulated with 100 gram Thinsulate. The liner shall attach with 2 front zippers and snaps at the neck and each cuff.

MFG/Model:

Spiewak H1764 or equal

Shell Fabric:

The shell shall be of 160 denier Cordura nylon warp and fill, finished with a non-ravel coating. The shell shall be treated with Teflon rain and stain finish. Weight: 4.1 oz per square yard, Coating: Non-ravel, Warp Yarn: 160-68SD, Filling Yarn: 160-68SD, Thread Count: epi (W x F) 103 x 71, Tensil Strength, lb (MD/XD): 149/98, Grab strength, lb (MD/XD): 242/162 lbs, Spray rating: 90-100, Tongue Tear, lb (MD/MX): 6/9, Color fastness and crocking: Good Abrasion resistance: 4lbs pressure/1 lb load: over 2000 cycles, Taber cycles: 126 cycles, Wyzenbeck: 303 cycles.

Permanent Body Lining:

Cloth type 100% nylon taffetam, 70 denier wrap and fill, color black, coating-WeatherTech waterproof/breathable. Lining weight: 3.3 oz per square yard, Mullen Hydrostatic: Avg 150 or better, Spray rating: 100, MVT E grms/SQM/24 hours: 5230.

All lining joining seams shall be safety stitched and then sealed with 1" heat sealed tape, to prevent leakage. The tape shall be applied by hot air method. Weather, temperature or storage shall not affect the tape. All stitching through the lining shall be sealed with waterproof tape. The label shall be sewn on a label carrier approximately 4" x 4" so as not to impede the performance of the lining. The label carrier shall be sewn at the neck and taped to prevent leakage at the neck area. There shall be a ligne 24 female snap on the label carrier to secure the removable liner. The lining shall extend through the top collar of the shell garment to form a waterproof barrier. There shall be 2 female snaps at the seam joining point and opposite, approximately 2 1/4" from the sleeve bottom, to attach to the removable liner. There shall be an inside storage pocket of shell material on the left side of the lining measuring approximately 8 1/2" deep by 7" wide. The pocket shall be taped at all points where the pocket is attached to prevent leakage.

Facings:

There shall be inside facing of shell material with a non-woven interlining approximately 1 1/4" wide on each side. There shall be a #5 18" delrin over the top YKK zipper set between the facing and the lining to attach the removable liner. The facing shall be backed with lining material and the seams taped to prevent leakage.

Front:

The front shall be 2 pieces joined double needle to allow for the box armhole construction. There shall be 2 front storm flaps over the front zipper to create a waterproof fly down the front of the jacket extending into collar. The outside fly shall measure 26" long by 2 1/2" wide. It shall be set double needle on the left side from the undercollar to the jacket bottom. The storm flap shall be interlined. There shall be 6 hidden/24 brass oxidized female snaps evenly spaced to correspond with the 6/24 brass oxidized male snaps on the inner storm fly. The inner storm fly shall measure approximately 26" long by approximately 1 3/4" wide. The inner storm flap shall be interlined and set down the front double needle. The front zipper shall be a #5 - 2 way delrin zipper 26" long. The flaps are constructed of a Reflexite GP430 high visibility lime green panel with POLICE printed in reflective blue letters. There shall be 1" silver scotchlite (8930) sewn onto the bottom Yoke, front and back.

Collar:

The collar shall be made of 2 piles of the shell material with an interlining sewn to the undercollar for stability. The collar points shall be well shaped and symmetrical. The top collar shall be lined with waterproof lining material and seam taped to prevent leakage where the collar is sewn to the neckline.

Sleeves:

The sleeves shall be constructed of 3 pieces of shell material to form a unique box armhole for freedom of movement.

The top sleeves shall be joined at the neck seam and sewn double needle down the back and front of the sleeve to the cuff. The top sleeve shall graduate from a width of approximately 4" (size large) at neckline to approximately 8" at the shoulder point to 5" at the cuff.

The front undersleeve shall be set double needle to the front at a point approximately 3 1/2" (size large) from the side seam to the top sleeve at the shoulder point, to form a partial dolman sleeve.

The back sleeve shall be set to the bi-swing area approximately 3 1/2' (large size) off the side seam to the shoulder point.

There shall be access zippers at the joining seams of the 2 undersleeves. The access zippers shall be approximately 10" (size large) from the underarm seam. The access zipper shall be a #3 nylon coil zipper measuring 9", to allow access to sew on patches without infiltrating the waterproof liner.

On the back under sleeve, there shall be an eyelet 1/2" from the cuff-joining sleeve to allow for water drainage.

Cuffs:

There shall be a cuff formed of 2 pieces of shell material approximately 1 5/8" wide at the bottom. Half of the cuff shall tab adjustment approximately 1 1/4" wide tapering to approximately 3/4" wide by 3" long, with female snap. The top half of the cuff shall be interlined and shall have 2 male snaps for cuff adjustment.

Epaulets:

There shall be an epaulet centered on each shoulder starting approximately 1" from the neckline. Epaulets shall measure 7" long by 2" wide at the shoulder point graduating to 1 3/4" wide at the narrow end. The epaulet shall be set with a cross-stitch 2" wide and will have a 24 ligne enameled snap closure at the point.

Pockets:

There shall be 2 inverted pleat patch pockets, measuring approximately 7 1/2" long by 7 1/2" wide. The pocket shall be interlined with Polar Fleece for warmth and comfort. The pocket flaps shall be attached to the front joining seam, shall measure 2 3/4" long by 8" wide, and shall have mitered corners. There shall be 2 ligne 24 snap closures and the pocket shall be bar tacked at both sides and at the hand warmer opening. There shall be a pencil pocket slit cut into the left front pocket flap. There shall be a pencil pocket cut/sewn into the left-hand pocket using the pocket flap as the penholder. Inside the right pocket on the right side, 2" below the top is a loop of black 1" elastic to hold a pepper spray.

Bottom Band:

The bottom band shall be constructed of 2 piles of shell material finishing 2" wide. The back band shall be constructed with heavy-duty elastic inserted between the folded fabric at the sides. The elastic shall be stretched and stitched with 2 threads. A 4" by 1 3/8" tab of 2 plies of shell material with a ligne 24 female snap (enameled cap) shall be provided to close the zipper vent when worn open. A brass oxidized male snap shall be provided to fold the tab back when not in use.

The front band shall be lined with a non-woven interlining for stability and a clean appearance. There shall be 2 ligne 24 oxidized male snaps spaced approximately 1 1/2" apart to which the tap closure will be attached when the zipper vent is open.

Side Vents:

There shall be 2 side vents with 9" nylon coil zippers to allow access to guns and equipment on either side with a snap/tab closure (see bottom band). There shall be 2 brass enameled eyelets located above the side vents on each side to allow for water drainage.

Back:

|Weight |Linear Yard |12.5 oz |

| |Square Yard |7.3 oz |

| |Square Meter |247 grm |

|Width Minimum: cuffable width inside pins | |60 in |

| | |152 cm |

| |Tolerance |Plus 2 in (5 cm) |

|Fiber content | |100% Polyester |

|Surface characteristics |Face |Non-Pil high performance velour pile |

| |Back |Fleece |

|Colorfastness |Average result |Nylon and acetate |

| | |Other fibers |

|Wash (AATCC-8) |Minimum standard |Nylon |

| | |Other fibers |

|Crocking (AATCC-8) |Average result |Wet: 4 Dry:4 |

| |Minimum |Wet: 3 Dry:4 |

|Light (20 hours) |Average result: | |

| |Minimum | |

|Flammability (AATCC 33-1962) |Standard |Class 1 |

|Thickness (Fed. Std. 5030) |Average Result |.200 in. 5.08 mm. |

|Stretch (ASTM D2594) |Average Result |60% width, N/A Length |

|Shrinkage (AATCC 135) |Procedure: Average Result: |Wash/Dry at 120 deg. F (3 times) |

| | | |

| |Maximum Standard Average Result: |Length: 3% x width 3% Length: 5%x Width: 5% |

|Air Permeability ASTM D737-75) Aiathermic insulation |Average result (Fleece only) |165 Cm 3/cm 2/sec, Clo rating: 1.20, og rating: 1.86 |

The back shall be 2 pieces joined double needle to allow for the box armhole construction. There shall be a bi-swing back with heavy-duty 1 3/4" elastic for freedom of movement.

The back has a full rain shed yoke with a 2" turn up designed to conceal the hidden ID flap system. The yoke is fully lined with nylon and there is an additional yoke facing of nylon. There are 3 Velcro sets on the yoke facing, that match the location of corresponding sets on the shell; to securely close the rain shed yoke, when flaps are concealed. Matching sets of velcro are provided on the underside of the ID flaps, which match corresponding Velcro sets on the yoke linings to hold the flaps in place when not in use. The back pull down flap measures approximately 16" long x 5" wide. The flap is attached to the jacket with a 16" #3 YKK interchangeable delrin zipper, so that it can be removed for cleaning. The flap is constructed of Reflexite GP430 high visibility lime green panel with POLICE printed in reflective blue letters.

Removable Liner:

The liner shall be a full zip body in/zip out liner. The lining color shall be black. The body shall be constructed of 100% nylon 70 denier (106 x 88) nylon quilted to 3M Thinsulate C100 in a 6" diamond pattern. The body shall be lined with a 100% Polar Fleece for maximum warmth and comfort. There shall be a collar of 100% 1 x 1 nylon stretch knit. There shall be a male brass oxidized snap centered at the neckline to attach the liner to the shell garment. There shall be 2 #5 delrin over the top 18" zippers that corresponds to the facing zippers in the shell garment. The sleeves shall be constructed of 100% nylon 70 denier 106 x 88 quilted back to back in a 6" diamond pattern to 3M Thinsulate C100. There shall be a knit gusset located under each arm approximately 4" by 12" to allow for freedom of movement. There shall be 2 male oxidized snaps at each sleeve bottom to correspond with the female snaps of the shell garment. The sleeves shall be shaped properly to fit the shell garment. There shall be 2 vents approximately 5 3/4" long to accommodate the side vents of the shell garment. All seams shall be sewn with a 5-needle safety stitch. The bottom and cuffs shall be finished with 100% nylon binding.

In order to provide maximum warmth and comfort, the following Polar Fleece specifications shall be adhered to:

All Weather Jacket Continued

Daytime/Nighttime Visibility Flaps:

Each panel is constructed of Reflexite GP430 (lime color) reflective garment tape. The tape is composed of cube corner (microprism) retro reflective elements integrally bonded to a flexible, smooth surfaced, tough and weather resistant US stabilized polymeric film. The prism surface are metalized to protect them form dirt and moisture and covered with heat activated adhesive for fusing.

Reflectivity:

Reflexite GP430 lime reflective garment tape, complies with the minimum reflectivity requirements of EN471 separate performance class 2, table 5, when tested at 8=0 degrees in accordance with the procedures in EN471 section 7.3.

Typical coefficients of retroreflection for GP430 lime reflective garment tape, when applied to fabric are shown in the following Table.

|Typical Reflectivity | | | | |

|ENTRANCE ANGLE | | | | |

|OBS ANGLE |5° |20° |30° |40° |

|0.2° |800 |600 |400 |210 |

|0.33° |380 |370 |290 |170 |

|1.0° |30 |25 |15 |12 |

|1.5° |11 |10 |8 |7 |

Each panel has matching high visibility/reflective blue lettering.

Back Length:

25 inches

Patches/Emblems:

There shall be one emblem sewn on each sleeve. There will be a badge patch sewn 1/2" above scotchlite on the left breast. All patches and emblems will be provided by Washington State Patrol

Color:

Dark Navy

Shell Fabric:

The shell consists of 160-denier CORDURA nylon, finished with a non-ravel coating. The minimum weight is 4.1 ounces per square yard. The shell is also treated with TEFLON Rain and Stain Resistant Finish, giving the jacket a spray rating of 90 - 100. The Fabric tensile strength, using the Grab Method: Warp = 242 lbs. Fill = 163 lbs.

Permanent Liner:

Cloth type 100% nylon taffeta, 70 denier wrap and fill, color black, coating - WeatherTech waterproof/breathable. Lining weight: 3.3 oz. per square yard, Mullen Hydrostatic: Avg. 150 or better, Spray rating: 100, MVT E grms/SQM/24 hours: 523.

All lining joining seams shall be safety stitched and then sealed with 1" heat sealed tape, to prevent leakage. The tape shall be applied by hot air method. Weather, temperature or storage shall not affect the tape. All stitching through the lining shall be sealed with waterproof tape.

Features:

The outside bottom of each leg has a #6 Nylon coil zipper, 16" long with an overfly or self-goods to cover the zipper. The overfly is closed with 2/24 ligne snaps. There is one drain hole located approximately 1 1/2" from the bottom of each leg. There are two cargo pockets on each leg. Each cargo pocket shall have one drain hole. There shall be four 'D' rings applied front and back for suspender attachment.

Cuffs:

Snap-adjustable cuffs with elastic allow pants to be pulled on over boots

Scotchlite:

There shall be 3" Safety yellow/Silver/Safety Yellow scotchlite applied on each leg in two different positions 3" above the hem and 9" above the hem.

Care:

Wash only. Do not dry clean.

7 WeatherTech Waterproof/Breathable Protective Pant

Shell Fabric:

The shell consists of 160-denier CORDURA nylon, finished with a non-ravel coating. The minimum weight is 4.1 ounces per square yard. The shell is also treated with TEFLON Rain and Stain Resistant Finish, giving the jacket a spray rating of 90 - 100. The Fabric tensile strength, using the Grab Method: Warp = 242 lbs. Fill = 163 lbs.

MFG/Model:

Spiewak 1755WST or equal.

Permanent Liner:

Cloth type 100% nylon taffeta, 70 denier wrap and fill, color black, coating - WeatherTech waterproof/breathable. Lining weight: 3.3 oz. per square yard, Mullen Hydrostatic: Avg. 150 or better. Spray rating: 100 MVT E grms/SQM/24 hours: 523. All lining joining seams shall be safety stitched and then sealed with 1" heat sealed tape, to prevent leakage. The tape shall be applied by hot air method. Weather, temperature or storage shall not affect the tape. All stitching through the lining shall be sealed with waterproof tape.

Features:

The outside bottom of each leg has a #6 Nylon coil zipper, 16" long with an overfly or self-goods to cover the zipper. The overfly is closed with 2/24 ligne snaps. There is one drain hole located approximately 1 1/2" from the bottom of each leg. There are two cargo pockets on each leg. Each cargo pocket shall have one drain hole. There shall be four 'D' rings applied front and back for suspender attachment

Cuffs:

Snap-adjustable cuffs with elastic allow pants to be pulled on over boots

Scotchlite:

There shall be 3" Safety yellow/Silver/Safety Yellow scotchlite applied on each leg in two different positions 3" above the hem and 9" above the hem.

Care:

Wash only. Do not dry clean.

CATEGORY FOUR - UNIFORM HATS AND ACCESSORIES

1 Fur/Felt Uniform Hat.

Style:

Stratton F-40 or equal.

Sizes:

6-1/2 - 7-7/8 Stratton F-40

SHAPE:

Stratton Hat Style F-40 or equal, Campaign Style also known as Montana Peak, traditional four dent crown, 5-1/4 inches high, double thick brim heavily sized, straight flat with a minimum thickness of 3mm with raw edge.

FUR/FELT QUALITY:

Stratton Hat #127 quality or equal, felt will be made of a fur mixture containing a minimum of 70% fine Hare's Fur (Arete 1 HXX - all white best) with the balance composed of virgin fur fibers only.

SWEATBAND:

Genuine leather, first selection, 1-5/8 inch wide.

RIBBON:

Width shall be 9 ligne, yard dyed grosgrain, Pattern #5551, finished edges.

EYELETS:

Shall have four (4) matching, enameled eyelets in crown, one on each side and one in back, 2-3/4 inches above brim. One front eyelet centered with height adjusted appropriately to accommodate post on hat badge shield. Brim shall have two (2) 3/8 inch oval Japanned black enamel eyelet, one on each side centered, to accommodate chin strap.

COLOR:

The felt shall be available in Washington Blue (Royal),Conservation Green, Olive Drab Colors, and Dark Brown to substantially match those presently in use.

BURSTING/STRENGTH:

The felt shall have a minimum bursting strength of 225 lbs

SIZE/AVAILABILITY:

Hat must be available in a full range of sizes, with specific molds for manufacturing each, as follows: 6-1/4; 6-3/8; 6-1/2; 6-5/8; 6-3/4; 6-7/8; 7; 7-1/8; 7-1/4; 7-3/8; 7-1/2; 7-5/8; 7-3/4; 7-7/8; 8

The following Oval Shapes must be available in each of the above sizes:

Wide Oval1 1/8 Inch Long Than Wide

Regular Oval 3/8 Inch Longer Than wide

Long Oval 1-7/8 Inch Longer Than Wide

Extra Long Oval 2-1/8 Inch Longer Than Wide

Regardless of the type of oval, brim width must measure three (3) inches at all distances from the crown.

Fur/Felt Uniform Hat Continued

PACKAGING:

Each hat shall be packed in individual cartons with BRIM-PRESS* type insert, which will allow the hat to rest firmly on bottom interior of carton, with firm support on top portion on brim, thereby assuring a flat brim indefinitely. Each individual fiberboard container and insert must have a bursting test strength minimum of 200 lbs. Each individual carton shall have plainly marked on the front exterior flap the size, shape and type of hat contained. The individual cartons shall be inserted into, a master carton containing one dozen hats, with size and shape clearly marked on the exterior. Master Carton shall be made of 200 lbs. test fiberboard.

2 ONE PIECE LEATHER STRAP

Stratton S + -1 –Bk or equal.

One piece leather strap, 3/8" wide, 30 long, belt notches begin 24-1/4 from buckle end, repeat every 5/8", and stop one inch from the end. Silver buckle 11/16" X 8/16". Sliding belt stay. Must be available in choice of black or dark brown. Strap must be hinged at each end below attachment to cording.

3 RAIN COVER,

Size: Sm - XL. Stratton RC-MP or equal

Rain Cover, made of Goodyear vinyl film, covers entire hat, brim of cover rolls under brim of hat. Sizes: Small (Hat Size 6-1/2, 6-5/8, 6-3/4) ; Medium (Hat Size 6-7/8, 7, 7-1/8) ; Large (Hat Size 7-1/4, 7-3/8) X-Large (Hat Size 7-1/2, 7-5/8, 7-3/4).

4 CORD, BRAID

COLOR:

Silver Or Gold, Stratton.

5 FELT HATS, PRE-BLOCKED

STYLE

Stratton F38A or equal

CROWN:

Hats to be pre-blocked with center crease and slight side dents; center crease 4-1.4" above brim and side dents 4-3/4" long and 3/8' deep.

BRIM:

3" double thickness. Sizing to be cleared from surface with a slight curl. Flare bow.

BRIM EYELET:

One oval eyelet each side centered to accommodate chin strap.

CROWN EYELETS:

Two (2) on each side, 1-1/8" apart and 2-3/8" above brim.

SWEATBAND:

Smooth grain, genuine leather, 1-5/8" wide. Oil silk backing.

COLOR:

Graphite Gray

SIZES AVAILABLE:

Hats must be available in a full range of sizes with specific molds for manufacturing each, as follows: 6-1/4; 6-3/8; 6-1/2; 6-5/8; 6-3/4; 6-7/8; 7; 7-1/8; 7-1/4; 7-3/8; 7-1/2; 7-5/8; 7-3/4; 7-7/8; 8

Felt Hats, Pre-Blocked

PACKAGING:

Each hat shall be packed in individual cartons with BRIM-PRESS* type insert, which will allow the hat to rest firmly on bottom interior of carton, with firm support on top portion of brim, thereby assuring a flat brim indefinitely. Each individual fiberboard container and insert must have a bursting test strength minimum of 200 lbs. Each individual carton shall have plainly marked on the front exterior flap the size, shape and type of hat contained. The individual cartons shall be inserted into a master carton containing one dozen hats, with size and shape clearly marked on the exterior. Master carton shall be sufficiently durable to withstand interstate commerce.

6 FUR CAP

STYLE

Stratton Genuine Mouton or equal.

SIZES:

6-1/2 - 8.

CROWN:

Uniroyal Vinyl, Brand "Doelon" shell, wind and waterproof. Crown to be cut in four pieces extending lengthwise from front to back, each of the two upper pieces to be approximately 3", wide finished at crown tapering to approximately 2" at back, each side piece approximately 3-1/2 at maximum width finished and cut to size, similar material to be used as backing for ear and neck flap, also front visor (peak).

FUR:

Mouton, first quality (flank or belly cut not acceptable), moutanized for water-proof ear and neck flaps (warmer) . Front visor (peak) approximately 7" at brim, according to size of cap tapering to rounded edges approximately 4" in height to be stitched to crown. Black Japanned metal eyelet #1 87 in center of visor to attach ornament. Black Japanned snap fastener on visor to hold same to cap crown. Adjustable black braid 1/2", 11-1/2" long finished by Black Japanned snap fastener sewn to cap to hold flaps up, also to fasten under chin when flaps are down.

LINING:

Fiber-Temp (Fiberglass satin quilted, brown with brown sweatband, hand finished.

COLORS:

Navy Blue, Black or Brown

SIZES AVAILABILITY:

Hats must be available to a full range of sizes with specific molds for manufacturing the following: 6-1/4; 6-3/8; 6-1/2; 6-5/8; 6-3/4; 6-7/8; 7; 7-1/8; 7-1/4; 7-3/8; 7-1/2; 7-5/8; 7-3/4; 7-7/8; 8

7 CAMPAIGN STYLE HATS

Summer/ Straw Campaign Style Hat

STYLE

Stratton S40DB or equal

Hemp Braid, Sizes: 6-1/2 - 7-7/8. Campaign Style And Montana Peaks Hats

QUALITY:

#1 Quality Bedford Hemp Braid, tight weave. 5 to 5-1/2 mm Width.

COLOR:

To match winter felts as closely as possible. Washington Blue (Royal), Conservation Green, Olive Drab and Dark Brown.

CROWN:

Traditional 4 dent style (Montana Peak)

SWEAT BAND:

Head culture foam seat with oil silk liner.

RIBBON:

9 ligne, yard dyed grosgrain.

BRIM:

3" wide-straight flat. Two separate brims joined for extra strength and shape retention. Brims are sewn together. Heavily stiffened and shower proofed. Made from 5-1/2 Bedford Hemp.

CROWN EYELETS:

3 to serve as vents, one on each side and one in the back, 2 - 3 /4 above brim.

BADGE EYELETS:

To your specifications, normally one in front 2-1/8" above brim.

BRIM EYELETS:

3/8" oval, one on each side, to accommodate chin strap - centered.

STIFFENING:

Crown double dipped. Brim triple dipped with #21 sizing by Kempen Paint.

SIZES:

Assorted sizes to be available.

8 THREE-PIECE HEADSTRAP, (Chin Strap).

Stratton or Equal Strap, Three Piece Leather, Center Strap 1/2 In. Wide, Ends 3/8 In. With Rivet Type Swivel And Closure. Color: Black

9 CATEGORY FIVE - Uniform Boots

Boot, Uniform, (Insulated)

10" Uppers, Uppers: 5 To 5¼ Oz. Full Grain Leather; Lining: 200 Gram Thinsulate And Cambrelle. Goretex Bootie For Waterproofing. Poron Texon Insole, Double Ribbed Steel Arch With Fiber Board Support. Midsole Of 12 Iron Eva, 4 Iron Composition. Heel And Base Of 30 Iron Eva. 148 Vibram Kletterlift Outsole. Black In Color. Speed Lace "D" Rings On 10" Boot With Washer Backing. No Speed Lace Hooks. Wraparound Sidelasting Construction To Hold Boot Shape And Hold Heel Back Into The Boot. Welt Construction So That Resole Of Boot Is Easily Accomplished Without Damage To Waterproofing.

MFG/ Model/Style: Danner Shoe MFG Company, 69110 - Fort Lewis Insulated or equal.

Packing: Boxed

Sizes Available: Men’s: 8-14B, 7-15D, 6-13EE Women’s: 5-10 Medium

Colors: Black

Boot Uniform (INSULATED)

Uniform Boots, (insulated) full grain leather, Cordura nylon inset, Cambrelle nylon lining, 200 gram Thinsulate. Gore-tex fabric bootie, cushion insole, steel shank, double layer midsole of thin, hard rubber and thick, soft EVA. Vibram Kletterlift sole, removable Danner Airthotic heel and arch support inserts. 8” Uppers.

MFG/ Model/Style: Danner Shoe MFG Company, Acadia 69210 or equal

Sizes Available: Men’s: 8-15D, 6-13EE Women’s: 5-10 Medium

Colors: Black

Boot, Uniform, (Uninsulated).

10" Uppers, Uppers: 5 To 5¼ Oz. Full Grain Leather; Lining: 200 Gram Thinsulate And Cambrelle. Goretex Bootie For Waterproofing. Poron Texon Insole, Double Ribbed Steel Arch With Fiber Board Support. Midsole Of 12 Iron Eva, 4 Iron Composition. Heel And Base Of 30 Iron Eva. 148 Vibram Kletterlift Outsole. Black In Color. Speed Lace "D" Rings On 10" Boot With Washer Backing. No Speed Lace Hooks. Wraparound Sidelasting Construction To Hold Boot Shape And Hold Heel Back Into The Boot. Welt Construction So That Resole Of Boot Is Easily Accomplished Without Damage To Waterproofing.

MFG/Model/Style: Danner Shoe MFG Company,: 29110 - Fort Lewis Uninsulated or equal.

Sizes Available: Men’s: 7-15D, 6-13EE Women’s: 5-10 Medium

Colors: Black

Boot, Uniform, (Uninsulated).

Uniform Boots, non-insulated full grain leather, Cordura nylon inset, Cambrelle nylon lining, Gore-tex fabric bootie, cushion insole, steel shank, double layer midsole of thin, hard rubber, and thick, soft EVA. Vibram Kletterlift sole, removable Danner Airthotic heel and arch support inserts. 8” Uppers.

MFG/Model/Style: Danner Shoe MFG Company, Acadia 21210 or equal

Sizes Available: Men’s: 8-15D, 6-13EE Women’s: 5-10 Medium

Colors: Black

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download