Current Contract Information Form - Washington



State of Washington

Current Contract Information

Revision date: January 28, 2012

Effective date: June 11, 2011

|Contract number: |03207 (replaces 02101 & 00300) |Commodity code: |6250 and 6210 |

|Contract title: |Steel Light Standards and Components (Category “A”) |

| |Roadway Luminaries and Lighting (Category “B”) |

|Purpose: |To extend the contract for its final 2 year term |

|Award date: |06-04-07 |

|Period of performance: |06-11-2011 |through: 06-10-2013 | |

|Contract term: |Not to exceed six years or 06-10-2013 | |

|Contract type: |This contract is designated as mandatory use. |

|Products/Services available: |Light Standards and Components; Shafts: Luminaire Mast Arms; Keeper Plates; Bolt Bases; Etc. |

|Related product contracts: | |

|Contract exclusions: |Specific reason(s) when not to use the contract. |

|Contractors: |This contract is awarded to single contractor. |

| |Consolidated Electrical Distributors, Inc. (CED) |

|Primary user agency(ies): |Washington State Department of Transportation (WSDOT) |

| |All State Agencies, Political Subdivisions of Washington and Oregon State, Qualified Non-profit Corporations, |

| |Materials Management Center, Participating Institutions of Higher Education (College and Universities, Community |

| |and Technical Colleges). |

|Contract pricing: |See page 7 thru 28 |

|Ordering information: |See page 2 Note III & IV |

|Ordering procedures: |See page 2 Note II |

|Current participation: | | | | |

| |$0.00 MBE |$0.00 WBE |$245,657 OTHER |$0.00 EXEMPT |

| |MBE 0% |WBE 0% |OTHER 100% |Exempt 0% |

|Contracts Specialist: |Nathan Hayes |

|Phone Number: |360-407-8236 |

|Fax Number: |360-586-2426 |

|Email: |nathan.hayes@des. |

Visit our Internet site: ga.

Notes:

I. Best Buy: The following provision applies to mandatory use contracts only. This contract is subject to RCW 43.19.190(2) & RCW 43.19.1905(7): which authorizes state agencies to purchase materials, supplies, services, and equipment of equal quantity and quality to those on state contract from non-contract suppliers. Provided that an agency subsequently notifies the Office of State Procurement (OSP) contract administrator that the pricing is less costly for such goods or services than the price from the state contractor.

If the non-contract supplier's pricing is less, the state contractor shall be given the opportunity by the state agency to at least meet the non-contractor's price. If the state contractor cannot meet the price, then the state agency may purchase the item(s) from the non-contract supplier, document the transactions on the appropriate form developed by OSP and forwarded to the SPO administering the state contract. (Reference General Authorities document)

If a lower price can be identified on a repeated basis, the state reserves the right to renegotiate the pricing structure of this agreement. In the event such negotiations fail, the state reserves the right to delete such item(s) from the contract.

II. State Agencies: Submit Order directly to Contractor for processing. Political Subdivisions: Submit orders directly to Contractor referencing State of Washington contract number. If you are unsure of your status in the State Purchasing Cooperative call (360) 902-7415 or visit

III. Only authorized purchasers included in the State of Washington Purchasing Cooperative (WSPC) and State of Oregon Cooperative Purchasing Program (DASCPP/ORCPP) listings published and updated periodically by OSP and DAS may purchase from this contract. It is the contractor’s responsibility to verify membership of these organizations prior to processing orders received under this contract. A list of Washington members is available on the Internet , and a list of the Oregon members is available at contractors shall not process state contract orders from unauthorized users.

IV. Contract Terms: This Document includes by reference all terms and conditions published in the original IFB, including Standard Terms and Conditions, and Definitions, included in the Competitive Procurement Standards published by OSP (as Amended).

Special Conditions:

1. Contractor to furnish to the Contracts Specialist, a copy of a valid Certificate of Insurance listing the State as beneficiary within fifteen (15) days after Contractor receipt of award notice.

2. If any of the pre-approved drawings are revised and approved by WSDOT Bridge and Structures Office during the term of this contract, the contractor shall supply light standards and components conforming to the revised drawings.

3. Component Identification

Light standards and luminaire arms will require identification tags. The tags shall conform to the detail shown on the pre-approved drawings. Slip base assemblies shall be bundled or packaged together complete with nuts, bolts, and washers and marked with the light standard number and contract number or purchase order number. Anchor bolt sets, complete with nuts, washers plates and templates shall be bundled and tagged with the contract number or purchase order identification numbers.

4. Documentation

All manufacturer certification reports, including mill certifications, non-destructive testing reports, and anchor bolt reports shall be submitted for each light standard, component, and anchor bolt set. All certifications and reports shall be marked with the purchase order number and contract number and shall be sent to the fabrication inspector. The contractor shall notify the state, in advance, of the arrival of the light standards and components at the delivery site so that inspection can be scheduled.

5. Quality Assurance Inspection

Quality assurance inspection for light standards and components purchased by WSDOT will be provided by the WSDOT Materials Fabrication Inspection Office. WSDOT purchasers shall contact the inspection office for information regarding inspection services. As the WSDOT Materials Laboratory operates on a cost recovery system, purchasers must provide a method of payment for inspection services. Other purchaser may also contact the Materials Fabrication Inspection Office for information regarding inspection services.

The following process is used for quality assurance inspection and acceptance of inspected items.

A. The purchaser shall notify the Materials Fabrication Inspection Office that they have placed an order for light standards and components (luminaire arms, slip base assemblies, anchor bolts, etc.) and that these items will require inspection at the fabrication plant or upon arrival at the delivery site*. (*The Materials Fabrication Inspection Office will determine the inspection site based on plant location.)

The notice shall include contact information, the purchase order number, contract number, estimated delivery date, and a method for the fabrication inspectors to recover their inspection costs. Contact information for the Fabrication Inspection Office can be found at: Mats Lab Fabrication Inspection ()

B. The fabricator shall give two business days notice to the WSDOT Materials Fabrication Inspection Office so that fabrication inspection can be scheduled. (Inspection site will be determined by fabrication inspection office.)

C. The fabricator shall make arrangements for delivery with the purchaser.

D. The Purchaser’s inspection of all materials and equipment upon delivery is for the sole purpose of identification. Such inspection shall not be construed as final acceptance or as acceptance of materials or equipment if materials or equipment do not conform to contractual requirements. If there are any apparent defects in the materials or equipment at the time of delivery, the Purchaser will promptly notify the Contractor thereof. Without limiting any other rights, the Purchaser and/or the State at its option, may require the Contractor to:

• Repair or replace, at Contractor's expense, any or all of the damaged goods,

• Refund the price of any or all of the damaged goods, or

• Accept the return of any or all of the damaged goods without penalties.

E. If inspection occurred at the fabrication site, light standards and components will be stamped or tagged “APPROVED FOR SHIPMENT”. If there are no stamps or tags, the Purchaser shall notify the WSDOT Materials Fabrication Inspection Office that the light standards or components have arrived at the delivery site and are ready for inspection.

F. The Materials Fabrication Inspection Office will inspect the light standards and components at the delivery site and if approved, they will be stamped or tagged “APPROVED FOR SHIPMENT”. Material certification and nondestructive test reports shall be provided by the manufacturer and shall be available at the time of inspection. Inspection at the delivery site is included in the 60 calendar day delivery time period (see also section 6.2 in original IFB).

If light standards or anchor bolts are not in compliance with the order, fail the fabrication inspection, or are damaged due to shipping, they shall be repaired to the satisfaction of the State or shall be replaced by the contractor at no additional cost to the State.

6. DELIVERY LOCATION

Light standards and components as well as roadway luminaires and lighting shall be delivered to the location points as indicated on the Field Order (which may be throughout the State of Washington). Regular business hours are defined as 8:00 AM to 3:30 PM Monday through Thursday, excluding Washington State Holidays. The contractor shall notify the purchaser three days prior to making a delivery. Deliveries outside the regular business hours must be pre-arranged with the purchaser. If contractor attempts to make delivery without prior arrangements, the State reserves the right to reject delivery

7. DELIVERY TIME

1 Steel light standards and components built in accordance with the pre-approved drawings will be delivered within 60 calendar days after acknowledgement of receipt of field order. Anchor bolts, if required, will be delivered within 15 calendar days after acknowledgement of receipt of field order. Longer delivery times on individual purchase transactions are authorized by written mutual agreement of the customer and contractor. The State reserves the right to modify the default delivery time, in the best interest of the state, upon mutual written agreement with the contractor.

The order and delivery procedure will be as follows:

1. WSDOT will fax or email field orders to the Contractor.

2. Contractor will acknowledge receiving field order by faxing a confirmation within four (4) business hours after receipt of field order. Business hours are defined as Monday through Friday, 8 AM to 3:30 PM (Pacific Daylight/Standard Time). For those field orders that are faxed or emailed to Contractor after 2:00 PM, the Contractor will process the field order first thing on the next working business day. The contractor’s delivery time will begin on the next business day.

3. The Contractor is required to submit shop drawings for light standards without pre-approved plans and for special base plates used on light standards with pre-approved drawings. Contractor will submit six (6) sets of the shop drawings to the WSDOT responsible party listed on the field order for review and approval. Pre-approved drawings are listed in Section 3.3. For light standards built in accordance with pre-approved plans, no shop drawings are required.

4. If needed, WSDOT responsible party will process the shop drawings in accordance with the WSDOT WSDOT Construction Manual M41-01 Section 8-20.2B. WSDOT responsible party will be allowed seven (7) calendar days to review the Contractor’s shop drawings for light standards built without pre-approved drawings. If the WSDOT responsible party requires a longer time period to review the shop drawings, the additional time will not count against the Contractor delivery time. After approval, the responsible party will distribute the shop drawings according to WSDOT Construction Manual M41-01 Section 8-20.2B and shall ensure that two copies are forwarded to the Fabrication Inspection Office.

5. Upon receipt of the stamped approved shop drawings, the Contractor will fabricate and ship the light standard(s) to the specified delivery point within the specified delivery period.

2 Roadway luminaires and lighting will be delivered within 60 calendar days after acknowledgement of receipt of field order (see also section 6.2).

Because of a high incidence of damage, each luminaire fixture must be opened and checked by purchaser for concealed damage. If there are signs of damage, it must be noted on the original Bill of Lading and Freight Bill. The shipping agent shall allow adequate time to open and check each fixture. It shall be the responsibility of the vendor to advise his shipping agent of this requirement.

PHOTOGRAPHING DAMAGE: Vendor pre-bid conference feedback demonstrates that photographs of damage are imperative in processing damage claims. The customer must reasonably photograph any delivery damage. Photographs must be safeguarded and maintained by the customer, with good copies timely disseminated to the contractor and the GA/OSP contract administrator. Best practice: Customer is not required but should take several photographs from multiple perspectives.

INSPECTION PRIOR TO OFF-LOADING: In the sole discretion of the customer, where it is safe to do, and where it is allowed by the customer’s safe operation/safe practices requirements, inspection should take place on the truck prior to off-loading of the materials.

OFF LOADING OF MATERIALS: Where mechanical means are necessary, the customer is responsible for off-loading of materials, i.e., forklift, dolly, hoist, etc. Any hand-carry materials are the responsibility of the contractor and his agent or carrier to off-load.

Contractor Information

|Contractor: |Consolidated Electrical Distributors |

| |24909 104th Avenue S.E. #202 |

| |Kent, WA 98030 |

|Contact: |Arthur Van Gelder |Jon Sande |

|Phone: |206-706-4929 |360-923-2345 |

|Fax: |206-783-8572 |360-459-9750 |

|Email: |cedavg@ |jsande@ |

|Federal ID No.: |770030773 |

|Order placement, payment address and |CED Olympia |CED Kent |

|customer service address: |5320 Lacey Blvd. S.E. |6409 S. 194th Street |

| |Lacey, WA 98503 |Kent, WA 98032 |

| |John Sande |Jon Whitsel |

| |Tel.: 360-923-2345 |Tel.: 253-893-7333 |

| |Fax: 360-459-9750 |Fax: 253-893-7296 |

| |Email: jsande@ |Email: jw@ |

| |CED Wenatchee |CED Yakima |

| |1420 N. Miller St. |131 S. 1st Ave. |

| |Wenatchee, WA 98801 |Lynn Carlson |

| |Tel.: 509-662-2129 |Tel.: 509-248-0872 |

| |Fax: 509-662-4776 |Fax: 509-248-1633 |

| |Email: john@ced- |Email: lcarlson@ |

| |CED Spokane |CED Anacortes |

| |E. 3717 Main St. |12756 Quantum Ln. Suite 30 |

| |Spokane, WA 99202 |Anacortes, WA 98221 |

| |Bill Keener |Zac Clark |

| |Tel.: 509-535-8891 |Tel.: 360-293-5818 |

| |Fax: 509-535-3745 |Fax: 360-293-5843 |

| |Email: bkeener@ |Email: zac@ |

| |CED Puyallup |CED Auburn |

| |14111 Pioneer Way E, Suite A |4826 B Street NW #105 |

| |Puyallup, WA 98372 |Auburn, WA 98001 |

| |Mat Oatman |Dave Phillips |

| |Tel: 253-841-1995 |Tel: 253-852-5454 |

| |Fax: 253-841-1961 |Fax: 253-852-0494 |

| |Email: moatman@ced- |Email: dave@ |

| |CED Richland |CED Bremerton |

| |1920 Fowler St. |4503 Auto Center Way |

| |Richland, WA 99352 |Bremerton, WA 98312 |

| |Jim Dunn |Ed Hamblet |

| |Tel: 509-737-8282 |Tel: 360-377-8585 |

| |Fax: 509-737-8383 |Fax: 360-373-5065 |

| |Email: jim@ced- |Email: ehamblet@ |

|Order placement, payment address and |CED Tacoma |CED Ellensburg |

|customer service address: |901 Center Street |412 S Railroad Ave. |

| |Tacoma, WA 98409 |Ellensburg, WA 98926 |

| |Ted Wilson |Dan Derosier |

| |Tel: 253-383-5961 |Tel: 509-925-4537 |

| |Fax: 253-383-0759 |Fax: 509-925-4337 |

| |Email: twilson@ced- |Email: dderosier@ |

| |CED Yakima |CED Everett |

| |131 S First Ave |3314 Cedar Street |

| |Yakima, WA 98902 |Everett, WA 98201 |

| |Will Sande |Jon Rayment |

| |Tel: 509-248-0872 |Tel: 425-259-8135 |

| |Fax: 509-248-1633 |Fax: 425-252-9344 |

| |Email: will@ |Email: jrayment@ |

| |CED Moses Lake |CED Port Angeles |

| |701 W Third Ave. |11 Prospect Place |

| |Moses Lake, WA 98837 |Port Angeles, WA 98362 |

| |Phil Matthews |Lance Miller |

| |Tel: 509-765-1251 |Tel: 360-452-9706 |

| |Fax: 509-765-1253 |Fax: 360-457-4510 |

| |Email: pmatthews@ |Email: lmiller@ |

|Ordering procedures: |See page 2 Note II |

|Credit card acceptance: |Yes |

|Delivery time: |60 days After Receipt of Order (ARO) |

|Payment terms: |Net 30 days |

|Shipping destination: |Freight on Board (FOB) destination |

|Freight: |Prepaid and included |

Category “A”

|Item |Description |Unit of Measure | |

| | | |Total Price |

|1. |40' mounting height shaft with post top mounting with three bolt base |Ea |$1,260.42 |

| |plate. | | |

| | | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS210-WS-040’MH-PTM-GV-HH-LAB | | |

|2. |37' mounting height shaft with post top mounting with special 4 bolt base |Ea |$1,500.58 |

| |plate. | | |

| | | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS210-WS-037’MH-PTM-GV-HH-LAB(4-Bolt) | | |

|3. |37' mounting height shaft with post top mounting with median barrier base |Ea |$1,477.05 |

| |plate. | | |

| | | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS210-WS-040’MH-PTM-GV-HH-LAB (Median) | | |

|4. |30' mounting height shaft for Type 1 luminaire arm with 3 bolt base plate.|Ea |$1,058.99 |

| | | | |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS90-30’MH-GV-HH-LAB-Fixed | | |

|Item |Description |Unit of Measure |Total Price |

|5. |40' mounting height shaft for Type 1 luminaire arm with 3 bolt base plate.|Ea |$1,190.47 |

| | | | |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS90-40’MH-GV-HH-LAB-Fixed | | |

|6. |50' mounting height shaft for Type 1 luminaire arm with 3 bolt base. |Ea |$1,760.83 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS90-50’MH-GV-HH-LAB-Fixed | | |

|7. |30' mounting height shaft for Type 1 luminaire arm with special 4 bolt |Ea |$835.53 |

| |base plate. | | |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS90-30’MH-GV-HH-LAB-(4-Bolt) | | |

|8. |40' mounting height shaft for Type 1 luminaire arm with special 4 bolt |Ea |$1,214.03 |

| |base plate. | | |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS90-40’MH-GV-HH-LAB-(4-Bolt) | | |

|Item |Description |Unit of Measure |Price |

|9. |40' mounting height shaft with elbow attachment for 6' Type 2 luminaire |Ea |$1,684.02 |

| |arm and 3 bolt base plate. | | |

| | | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-40’MH-GV-HH-LAB-Elbow-6’ | | |

|10. |40' mounting height shaft with elbow attachment for 8' Type 2 luminaire |Ea |$1,698.54 |

| |arm and 3 bolt base plate. | | |

| | | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-40’MH-GV-HH-LAB-Elbow-8’ | | |

|11. |40' mounting height shaft with elbow attachment for 10' Type 2 luminaire |Ea |$1,683.31 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-40’MH-GV-HH-LAB-Elbow-10’ | | |

|Item |Description |Unit of Measure |Price |

|12. |40' mounting height shaft with elbow attachment for 12' Type 2 luminaire |Ea |$1,778.83 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-40’MH-GV-HH-LAB-Elbow-12’ | | |

|13. |40' mounting height shaft with elbow attachment for 14' Type 2 luminaire |Ea |$1,799.59 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-40’MH-GV-HH-LAB-Elbow-14’ | | |

|14. |40' mounting height shaft with elbow attachment for 16' Type 2 luminaire |Ea |$1,668.48 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-40’MH-GV-HH-LAB-Elbow-16’ | | |

|15. |50' mounting height shaft with elbow attachment for 8' Type 2 luminaire |Ea |$1,802.36 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-50’MH-GV-HH-LAB-Elbow-8’ | | |

|Item |Description |Unit of Measure |Price |

|16. |50' mounting height shaft with elbow attachment for 12' Type 2 luminaire |Ea |$1,818.89 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-50’MH-GV-HH-LAB-Elbow-12’ | | |

|17. |50' mounting height shaft with elbow attachment for 16' Type 2 luminaire |Ea |$1,818.89 |

| |arm and 3 bolt base plate. | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-50’MH-GV-HH-LAB-Elbow-16’ | | |

|18. |47' mounting height shaft with elbow attachment for 8' Type 2 double |Ea |$1,494.79 |

| |luminaire arms and special 4 bolt base plate. | | |

| | | | |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |DS99-47’MH-GV-HH-LAB-Elbow-8’ (4-Bolt) | | |

|19. |6' Type 1 luminaire arm. |Ea |$441.45 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |6’ Type 1 ARM DS90 | | |

|Item |Description |Unit of Measure |Price |

|20. |8' type 1 luminaire arm. |Ea |$469.39 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |8’ Type 1 ARM DS90 | | |

|21. |10' Type 1 luminaire arm. |Ea |$480.57 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |10’ Type 1 ARM DS90 | | |

|22. |12' Type 1 luminaire arm. |Ea |$457.28 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |12’ Type 1 ARM DS90 | | |

| | | | |

|23. |14' Type 1 luminaire arm. |Ea |$499.73 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: | | |

| |14’ Type 1 ARM DS90 | | |

|24. |16' Type 1 luminaire arm. |Ea |$476.71 |

| |Pre-approved Drawing No.: DB00654 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 16’ Type 1 ARM DS90 | | |

|Item |Description |Unit of Measure |Price |

|25. |6' Type 2 luminaire arm. |Ea |$372.38 |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 6’ Type 2ARM DS99 | | |

|26. |8' Type 2 luminaire arm. |Ea |$386.22 |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 8’ Type 2ARM DS99 | | |

| | | | |

|27. |10' Type 2 luminaire arm. |Ea |$394.53 |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 10’ Type 2ARM DS99 | | |

|28. |12' Type 2 luminaire arm. |Ea |$408.37 |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 12’ Type 2ARM DS99 | | |

|29. |14' Type 2 luminaire arm. |Ea |$419.44 |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 14’ Type 2ARM DS99 | | |

|Item |Description |Unit of Measure |Price |

|30. |16' Type 2 luminaire arm. |Ea |$408.05 |

| |Pre-approved Drawing No.: DB00653 Rev. A | | |

| | | | |

| |Mfg.:Valmont | | |

| |Catalog/ Design No: 16’ Type 2ARM DS99 | | |

|31. |3 bolt slip base assembly with clamping bolts and keeper plate. |Ea |$964.86 |

| |Mfg.:Valmont | | |

| |Brand/Model: Slip Base Assembly Kit | | |

|32. |Slip base adapter type A-1 for 4-bolt light standard base and 4 bolt |Ea |$953.78 |

| |foundation. | | |

| |Mfg.:Valmont | | |

| |Brand/Model: Slip Base Adapter (Type 1A 4-Bolt) | | |

|33. |1" anchor bolt set for 3 bolt base or slip base. |Ea |$345.87 |

| |Mfg.:Valmont | | |

| |Brand/Model: 1” Anchor Bolts (Set of 3) | | |

|34. |1" anchor bolt set for 4 bolt base. |Ea |$492.81 |

| |Mfg.:Valmont | | |

| |Brand/Model: 1” Anchor Bolts (Set of 4) | | |

CATEGORY “B”

General Electric

|Item |Description |G.E. CAT. # |UoM |Current Price |Prices effective November 27,|

| | | | | |2008 |

| |200W HPS 240V w/out PE Socket |MDCL20S3M12FMC32 |Ea |$184.16 |$186.92 |

| |200W HPS 480V w/out PE Socket |MDCL20S5M12FMC32 |Ea |$176.56 |$179.21 |

| |200W HPS Multi-Volt w/out PE Socket |MDCL20S0M12FMC32 |Ea |$179.65 |$182.34 |

| |200W HPS 120V w/PE Socket |MDCL20SIM22FMC32 |Ea |$184.16 |$186.92 |

| |200W HPS 480V w/PE Socket |MDCL20S5M22FMC32 |Ea |$176.56 |$179.21 |

| |200W HPS Multi-Volt Power Door Ballast Unit |MDRL20SOM |Ea |$122.60 |$124.44 |

| |200W HPS 480V Power Door Ballast Unit |MDRL20S5M |Ea |$122.60 |$124.44 |

| |250W HPS 240V w/out PE Socket |MDCL25S3M12FMC32 |Ea |$192.80 |$195.69 |

| |250W HPS 480V w/out PE Socket |MDCL25S5M12FMC32 |Ea |$192.80 |$195.69 |

| |250W HPS Multi-Volt w/out PE Socket |MDCL25SOM12FMC32 |Ea |$187.89 |$190.71 |

| |250W HPS 120V w/PE Socket |MDCL25S1M22FMC32 |Ea |$198.20 |$201.17 |

| |250W HPS Multi Volt Power Door Ballast Unit |MDRL25SOM |Ea |$133.40 |$135.40 |

| |250W HPS 240V w/PE Socket |MDCL25S3M22FMC32 |Ea |$191.20 |$194.07 |

| |250W HPS 480V Power Door Ballast Unit |MDRL25S5M |Ea |$128.00 |$129.92 |

| |310W HPS 240V w/out PE Socket |MDCL31S3M12FMC32 |Ea |$188.92 |$191.75 |

| |310W HPS 480V w/out PE Socket |MDCL31S5M12FMC32 |Ea |$188.92 |$191.75 |

General Electric (continued)

|Item |Description |G.E. CAT. # |UoM |Current |Prices effective November |

| | | | |Price |27, 2008 |

| |310W HPS Multi-Volt w/out PE Socket |MDCL31SOM12FMC32 |Ea |$192.01 |$194.89 |

| |310W HPS Multi Volt Power Door Ballast Unit |MDRL31SOM |Ea |$133.40 |$135.40 |

| |310W HPS 240V w/PE Socket |MDCL31S3M22FMC32 |Ea |$202.52 |$205.56 |

| |310W HPS 480V Power Door Ballast Unit |MDRL31S5M |Ea |$133.40 |$135.40 |

| |400W HPS 240V w/out PE Socket |MDCL40S3M12FMC32 |Ea |$199.28 |$202.27 |

| |400W HPS 480V w/out PE Socket |MDCL40S5M12FMC32 |Ea |$190.98 |$193.84 |

| |400W HPS Multi-Volt w/out PE Socket |MDCL40SOM12FMC32 |Ea |$193.04 |$195.94 |

| |400W HPS Multi-Volt Power Door Ballast Unit |MDRL40SOM |Ea |$139.88 |$141.98 |

| |400W HPS 480V Power Door Ballast Unit |MDRL40S5M |Ea |$137.66 |$139.72 |

| |Starter Boards for Cobra Heads |35-216710R01 |Ea |$29.50 |$29.94 |

| |Starter Boards For Cobra Heads |35-216700R10 |Ea |$29.50 |$29.94 |

| |200 W HPS 120/240 V W/OUT PE SOCKET |MDCA20S7M12FMC3N |Ea |$202.31 |$205.34 |

| |250 W HPS 120/240 V W/OUT PE SOCKET |MDCA25S7M12FMC3N |Ea |$218.72 |$222.00 |

| |400 W HPS 120/240 V W/OUT PE SOCKET |MDCA40S7M12FMC3N |Ea |$214.67 |$217.89 |

| |200 W HPS 480 V W/OUT PE SOCKET |MDCA20S5M12FMC3N |Ea |$205.76 |$208.85 |

| |250 W HPS 480 V W/OUT PE SOCKET |MDCA25S5M12FMC3N |Ea |$211.16 |$214.33 |

| |400 W HPS 480 V W/OUT PE SOCKET |MDCA40S5M12FMC3N |Ea |$218.72 |$222.00 |

LED Luminaries

|Item |Part Number |Description |UOM | Price Per Ea. |

|1. |STR-LWY-2M/3M/5M-HT-03-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 30 LEDs 120/277V Silver/Bronze |Ea | $375.00 |

| |/700-60K/43K-PD-R | | | |

|2. |STR-LWY-2M/3M/5M-HT-03-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 30 LEDs 480V Silver/Bronze |Ea | $425.00 |

| |/700-60K/43K-PD-R | | | |

|3. |STR-LWY-2M/3M/5M-HT-04-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 40 LEDs 120/277V Silver/Bronze |Ea | $445.00 |

| |/700-60K/43K-PD-R | | | |

|4. |STR-LWY-2M/3M/5M-HT-04-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 40 LEDs 480V Silver/Bronze |Ea | $490.00 |

| |/700-60K/43K-PD-R | | | |

|5. |STR-LWY-2M/3M/5M-HT-05-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 50 LEDs 120/277V Silver/Bronze |Ea | $525.00 |

| |/700-60K/43K-PD-R | | | |

|6. |STR-LWY-2M/3M/5M-HT-05-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 50 LEDs 480V Silver/Bronze |Ea | $570.00 |

| |/700-60K/43K-PD-R | | | |

|7. |STR-LWY-2M/3M/5M-HT-06-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 60 LEDs 120/277V Silver/Bronze |Ea | $555.00 |

| |/700-60K/43K-PD-R | | | |

|8. |STR-LWY-2M/3M/5M-HT-06-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 60 LEDs 480V Silver/Bronze |Ea | $595.00 |

| |/700-60K/43K-PD-R | | | |

| 9. |STR-LWY-2M/3M/5M-HT-07-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 70 LEDs 120/277V Silver/Bronze |Ea | $685.00 |

| |/700-60K/43K-PD-R | | | |

| 10. |STR-LWY-2M/3M/5M-HT-07-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 70 LEDs 480V Silver/Bronze |Ea | $725.00 |

| |/700-60K/43K-PD-R | | | |

| 11. |STR-LWY-2M/3M/5M-HT-08-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 80 LEDs 120/277V Silver/Bronze |Ea | $735.00 |

| |/700-60K/43K-PD-R | | | |

| 12. |STR-LWY-2M/3M/5M-HT-08-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 80 LEDs 480V Silver/Bronze |Ea | $780.00 |

| |/700-60K/43K-PD-R | | | |

| 13. |STR-LWY-2M/3M/5M-HT-09-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 90 LEDs 120/277V Silver/Bronze |Ea | $790.00 |

| |/700-60K/43K-PD-R | | | |

| 14. |STR-LWY-2M/3M/5M-HT-09-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 90 LEDs 480V Silver/Bronze |Ea | $835.00 |

| |/700-60K/43K-PD-R | | | |

| 15. |STR-LWY-2M/3M/5M-HT-10-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 100 LEDs 120/277V Silver/Bronze |Ea | $912.00 |

| |/700-60K/43K-PD-R | | | |

| 16. |STR-LWY-2M/3M/5M-HT-10-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 100 LEDs 480V Silver/Bronze |Ea | $960.00 |

| |/700-60K/43K-PD-R | | | |

| 17. |STR-LWY-2M/3M/5M-HT-11-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 110 LEDs 120/277V Silver/Bronze |Ea | $980.00 |

| |/700-60K/43K-PD-R | | | |

| 18. |STR-LWY-2M/3M/5M-HT-11-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 110 LEDs 480V Silver/Bronze |Ea | $1,025.00 |

| |/700-60K/43K-PD-R | | | |

|19. |STR-LWY-2M/3M/5M-HT-12-D-UL-SV/BZ-525|Beta - LED Pole mounted Streetlight 120 LEDs 120/277V Silver/Bronze |Ea | $1,050.00 |

| |/700-60K/43K-PD-R | | | |

|20. |STR-LWY-2M/3M/5M-HT-12-D-UH-SV/BZ-525|Beta - LED Pole mounted Streetlight 120 LEDs 480V Silver/Bronze |Ea | $1,095.00 |

| |/700-60K/43K-PD-R | | | |

| 21. |PKG-304-5M-DM/HC/PD-04-D-UL-SV/BZ-350|Beta - LED Canopy/Garage Fixture 40 LEDs 120/277V Silver/Bronze |Ea | $465.00 |

| |/525/700-60K/43K | | | |

| 22. |PKG-304-5M-DM/HC/PD-04-D-UL-SV/BZ-350|Beta - LED Canopy/Garage Fixture 40 LEDs 120/277V Silver/Bronze w/Occ.Sens. |Ea | $575.00 |

| |/525/700-60K/43K-ML | | | |

| 23. |PKG-304-5M-DM/HC/PD-06-D-UL-SV/BZ-350|Beta - LED Canopy/Garage Fixture 60 LEDs 120/277V Silver/Bronze |Ea | $525.00 |

| |/525/700-60K/43K | | | |

| 24. |PKG-304-5M-DM/HC/PD-06-D-UL-SV/BZ-350|Beta - LED Canopy/Garage Fixture 60 LEDs 120/277V Silver/Bronze w/Occ.Sens. |Ea | $635.00 |

| |/525/700-60K/43K-ML | | | |

|25. |GCA2-120E-MV-NW-2-GY-530-WL          |Leotek     Buy america 120 LED 4300K Type II- W ANSI Wattage Label |Ea |$991.00 |

| |    | | | |

|26. |BXSP-A-O-2/3-1/A-A-U-S/Z-R |Beta/Cree - Replaces 100 Watt HPS 120V/277V |Ea |$255.00 |

|27. |BXSP-A-O-2/3-1/A-A-V-S/Z-R |Beta/Cree - Replaces 100 Watt HPS 480V |Ea |$310.00 |

|28. |BXSP-A-O-2/3-G/N-A-U-S/Z-R-Q |Beta/Cree - Replaces 150 Watt HPS 120/277V |Ea. |$335.00 |

|29. |BXSP-A-O-2/3-G/N-A-V-S/Z-R-Q |Beta/Cree - Replaces 150 Watt HPS 480V |Ea. |$390.00 |

|30. |BXSP-A-O-2/3-2/B-A-U-S/Z-R-Q |Beta/Cree - Replaces 200 Watt HPS 120/277V |Ea. |$375.00 |

|31. |BXSP-A-O-2/3-G/B-A-V-S/Z-R-Q |Beta/Cree - Replaces 200 Watt 480V |Ea. |$430.00 |

|32. |BXSP-A-O-2/3-H/P-A-U-S/Z-R-Q |Beta/Cree - Replaces 250 Watt HPS120/277V |Ea. |$475.00 |

|33. |BXSP-A-O-2/3-H/P-A-U-S/Z-R-Q |Beta/Cree - Replaces 250 Watt 480V |Ea. |$530.00 |

|34. |BXSP-A-O-2/3-H/P-L-U-S-R |Beta/Cree - Replaces 310 Watt HPS 120V/277V |Ea. |$565.00 |

|35. |BXSP-A-O-2/3-H/P-L-U-S-R-Q |Beta/Cree- Replaces 400 Watt HPS 120V/277V |Ea. |$580.00 |

|36. |ARE-EDR-2M/3M/5M/5S-R3-04-D-UL-BZ/BK-|Beta/Cree – Pathway Fixture |Ea. |$890.00 |

| |350/525-40K | | | |

|37. |ARE-EDR-2M/3M/5M/5S-R3-04-D-UH-BZ/BK-|Beta/Cree – Pathway Fixture |Ea. |$950.00 |

| |350/525-40K | | | |

|38. |ARE-EDR-2M/3M/5M/5S-R3-08-D-UL-BZ/BK-|Beta/Cree – Pathway Fixture |Ea. |$1140.00 |

| |350/525-40K | | | |

|39. |ARE-EDR-2M/3M/5M/5S-R3-08-D-UH-BZ/BK-|Beta/Cree – Pathway Fixture |Ea. |$1190.00 |

| |350/525-40K | | | |

|40. |ATB2 80BLEDE70 480 DIMR3 |Volume discount pricing available for this item only: Autobahn LED Roadway- |1-49 |$1,080.00 |

| | |Large(ATB2); ATB2, 80B Chips,700mA Driver,480V, Type III, Step Down Transformer with | | |

| | |Dimmable Driver and ROAM dimming control module. | | |

| | | |50-199 |$998.50 |

| | | |200 + |$900.00 |

|41. |ATB2 60BLEDE10 480 DIMR3 |Volume discount pricing available for this item only: |1-49 |$878.00 |

| | |Autobahn LED Roadway- Large(ATB2); ATB2, 80B Chips,1000mA Driver,480V, Type III, Step | | |

| | |Down Transformer with Dimmable Driver and ROAM dimming control module. | | |

| | | |50-199 |$825.00 |

| | | |200+ |735.00 |

|42. |ATB2 80BLEDE70 MVOLT DIMR3 |Volume discount pricing available for this item only: |1-49 |$1,080.00 |

| | |Autobahn LED Roadway- Large(ATB2); ATB2, 80B Chips,700mA Driver, Multivolt 120-277V, | | |

| | |Type III, Step Down Transformer with Dimmable Driver and ROAM dimming control module. | | |

| | | |50-200 |$998.50 |

| | | |200+ |$735.00 |

|43. |ATB2 60BLEDE10 MVOLT DIMR3 |Volume discount pricing available for this item only: |1-49 |$878.00 |

| | |Autobahn LED Roadway- Large(ATB2); ATB2, 80B Chips,1000mA Driver, Multivolt 120-277V, | | |

| | |Type III, Step Down Transformer with Dimmable Driver and ROAM dimming control module. | | |

| | | |50-199 |$825.00 |

| | | |200+ |$735.00 |

NOTE: FOR WSDOT purchases of LED luminaries, please contact Ted Bailey @ 360.705.7286 or BAILEYTE@wsdot. prior to ordering.

Miscellaneous

|Item |Description | |UoM | Price |

| |Luminaire |HOLOPHANE WSDOT PREDATOR PF250HP24LN3D-F2 |Ea |$541.09 |

| |Luminaire |HOLOPHANE WSDOT PANEL-VUE MULTI-VOLT |Ea |$552.86 |

| |Luminaire |HOLOPHANE WSDOT PANEL-VUE 480 VOLT |Ea |$537.92 |

| |Ballast |HOLOPHANE WSDOT PANEL-VUE MULTI-VOLT |Ea |$74.75 |

| |Ballast |HOLOPHANE WSDOT PANEL-VUE 480 VOLT |Ea |$74.75 |

| |Refractor |HOLOPHANE WSDOT PANEL-VUE |Ea |$99.35 |

| |Mounting Plate |HOLOPHANE WSDOT PANEL-VUE |Ea |$97.25 |

| |Wire Guard |HOLOPHANE WSDOT PANEL-VUE |Ea |$42.85 |

| |Luminaire |GARDCO |Ea |$1,080.50 |

| | |JEH1913-400HPS-240-MAGREG-NA | | |

| |Luminaire |GARDCO |Ea |$1,080.50 |

| | |JEH1913-400HPS-480-MAGREG-NA | | |

| |Luminaire |GARDCO |Ea |$1,232.75 |

| | |JEH191VS-400HPS-480- MAGREG-NA-POLY | | |

| |Controller |SUN-TECH PHOTO CONTROLLER |Ea. |$32.50 |

| | |3TRS-2-105-305 | | |

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download