ARCAT | Free Building Product CAD Details, BIM, Specs and …

 SECTION 10 22 13WIRE MESH PARTITIONSDisplay hidden notes to specifier. (Don't know how? Click Here) Copyright 2017 - 2019 ARCAT, Inc. - All rights reserved** NOTE TO SPECIFIER ** Folding Guard; safety and security wire mesh products..This section is based on the products of Folding Guard, which is located at:5858 W. 73rd StreetBedford Park, IL 60638Tel: (708) 325-0400Fax: (708) 325-0450Email: sales@ Web: For over 40 years, Folding Guard Corporation has been the premier choice for wire mesh safety and security products. Folding Guard Corporation offers sales and service through dealers throughout North America.At Folding Guard?, our mission is to continually improve our quality practices and employee involvement to manufacture the best wire product solutions for all your safety, security, and storage needs.Our sales, customer service, design and engineering professionals are at your service and committed to your complete satisfaction every step of the way.

GENERAL

SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project. Add items that apply to project.

Welded Wire Mesh Partition Assemblies.

Framed Welded Wire Partitions.

Woven Wire Mesh Partition Assemblies..

RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

Section 03 30 00 - Cast-in-Place Concrete

Section 04 27 23 - Cavity Wall Unit Masonry

Section 09 21 16.33 - Gypsum Board Area Separation Wall Assemblies

SUBMITTALS

Submit under provisions of Section 01 30 00 - Administrative Requirements.

Product Data: Manufacturer's data sheets on each product to be used, including:

Preparation instructions and recommendations.

Storage and handling requirements and recommendations.

Installation methods.

Shop Drawings: Complete layout and fabrication drawings.

Keys: Turn over keys for door locks to Owner at completion of project.

QUALITY ASSURANCE

Manufacturer Qualifications: Minimum 10 years experience manufacturing products similar to those specified.

Installer Qualifications: Minimum 2 years experience installing products similar to those specified.

DELIVERY, STORAGE, AND HANDLING

Deliver and store products in manufacturer's properly labeled unopened packaging until ready for installation.

Store products in a dry, weather protected location. Do not store outside or allow getting wet.

SEQUENCING

Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

PRODUCTS

MANUFACTURERS

Acceptable Manufacturer: Folding Guard, which is located at: 5858 W. 73rd St.; Bedford Park, IL 60638; Toll Free Tel: 800-622-2214; Tel: 708-325-0400; Fax: 708-325-0450; Email: request info (sales@); Web:

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

Substitutions: Not permitted.

Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

** NOTE TO SPECIFIER ** Select the paragraphs for the products required and delete those not required.

WELDED WIRE MESH PARTITIONS

** NOTE TO SPECIFIER ** Qwik-Fence? Welded Wire Partitions is an extremely tough, but attractive, system for separating and securing any space. We secure galvanized wire in a grid pattern welded at each intersection. The process produces a wire mesh partition panel that is substantially stronger than woven wire partitions. The modular component system makes planning, installing, and relocating easy in any space. Modular panels stack together to form partitions up to 20 feet in height. Hardware is accessible from inside the partition for additional security. Universal line and corner posts are installed every 8 feet on center. Extension posts can be added to increase the height of any Qwik-Fence enclosure without reinstallation.

Partition Assembly: Model Qwik-Fence partitions as manufactured by Folding Guard. Provide to the size(s) indicated on the Drawing.

Modular Panel Sizes: Modular panels are available in the following sizes.

8 feet by 1 foot

8 feet by 2 foot

8 feet by 3 foot

8 feet by 4 foot

8 feet by 5 foot

10 feet by 1 foot

10 feet by 2 foot

10 feet by 3 foot

10 feet by 4 foot

10 feet by 5 foot

Panel Construction:

** NOTE TO SPECIFIER ** Select one of the following 3 panel paragraphs and delete those not required. Note that mesh with 1-1/2 inches (38 mm) by 3 inches (76 mm) grid openings is standard.

Fabricated of No. 8 gauge (0.160 inch) (4 mm) galvanized welded-wire mesh with 1-1/2 inches (38 mm) by 3 inches (76 mm) grid openings and 1-1/2 inches (38 mm) bends on top and bottom. Modifiable in the field.

Fabricated of No. 8 gauge (0.160 inch) (4 mm) galvanized welded-wire mesh with 1-1/2 inches (38 mm) by 1-1/2 inches (38 mm) grid openings and 1-1/2 inches (38 mm) bends on top and bottom.

Panels are welded at each intersection of the steel mesh wires.

Posts: Posts are universal 2 inch (51 mm) by 2 inch (51 mm), 14-gauge galvanized steel. Posts are welded to 6 inch (151 mm) by 2 inch (51 mm) by 1/4 inch (6 mm) mounting plate.

Posts are available at the following heights:

8 feet 0 inches (2.4 m) Universal Post (Standard)

8 feet 0 inches (2.4 m) Post Flat

8 feet 0 inches (2.4 m) Post Flat/Offset

1 feet 0 inches (0.30 m) Extension Post

2 feet 0 inches (0.61 m) Extension Post

3 feet 0 inches (0.91 m) Extension Post

4 feet 0 inches (1.22 m) Extension Post

6 feet 0 inches (1.83 m) Extension Post

8 feet 0 inches (2.44 m) Extension Post

Custom height (specify ________).

Wire mesh is attached to universal posts by six panel clips and six #12-14 by 1 inch (25.4 mm) zinc plated self-drilling/self-tapping screws.

Doors:

** NOTE TO SPECIFIER ** Select one or more of the following three Door paragraphs and delete those not required.

Hinged Doors: Pre-hung standard 94 inch (2.39 M) clear-height opening. 10-gauge welded-wire mesh.

Width:

** NOTE TO SPECIFIER ** Select one the following paragraphs and delete the one not required.

Single door, 3 foot (0.91 M)

Single door, 4 foot (1.22 M)

Pair doors, 3 foot (0.91 M) (two 3 foot panels)

Pair doors, 4 foot (1.22 M) (two 4 foot panels)

Door Panel Construction: Panels shall be welded of-10 gauge (0.135 inch) (3.4 mm) steel wire in a 1-1/4 inches (32 mm) by 2-1/2 inches (64 mm) grid openings with wires securely welded to steel angle frames. Vertical and horizontal frames shall be 1-1/2 inches (38 mm) by 1-1/2 inches (38 mm) 14 gauge steel angle. Corner joint construction shall be a lap joint design, with one full width 3/16 inches (5 mm) weld at each corner junction. Wire mesh panels to be supported by 2 inches square (51 mm) 16 gauge steel tube, welded to a 2 inches (61 mm) by 6 inches (152 mm) by 1/4 inch (6 mm) steel base plate.

Sliding Doors: Pre-hung with standard 94 inch (2.39 M) clear-height opening. 10-gauge welded-wire mesh.

Type/Size:

** NOTE TO SPECIFIER ** Select one the following paragraphs and delete the one not required.

Single Sliding/3 foot (0.91 M)

Single Sliding/4 foot (1.22 M)

Single Sliding/5 foot (1.52 M)

Single Sliding/6 foot (1.83 M)

Single Sliding/8 foot (2.44 M)

Single Sliding/10 foot (3.05 M)

Pair Sliding/8 foot (2.44 M) consisting of two 4 foot wide panels.

Pair Sliding/10 foot (3.05 M) consisting of two 5 foot wide panels.

Sliding Door Panel Construction: Sliding door frame shall be 1-1/2 inches by 1-1/2 inches (38 mm by 38 mm) 14 gauge angle on all four sides (full frame). Horizontal reinforcing at 42 inches (1067 mm) high shall be a formed 8 inch (203 mm) wide fender plate, welded in place with two angles 1 inch by 1 inch (25 mm by 25 mm) top and bottom, secured to side frames with a minimum of five weld points each side.

Track/Hangers: Door equipped with a heavy box track, two 2-1/8 inch (54 mm) diameter four-wheel ball bearing hangers, and bottom guide channel.

Door Hardware Options:

All hardware included.

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete those not required. Consult with factory for other options.

Built-in cylinder lock, keyed different, Standard.

Built-in cylinder lock, keyed alike.

Built-in double cylinder lock, keyed different.

ADA-compliant lock

Push-button lock

Electric strike/card reader locks

Interlock switches

Crash/panic bars

Spring hinges

Automatic closures

Service window.

Padlock hasp.

Component Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete those not required. Consult factory for additional information.

Roof Support

Ceiling Tube

Ceiling Wall Angle

Wall Kit

Service Window Kit

Top Post Extension

Header 2 inch by 2 inch (51 mm by 51 mm)

Capping Channel 96 inches (2.44 m)

Roof

8 foot (2.44 m) Door Transom Kit to Fit 8 foot (2.44 m) Door into 10 foot (3.05m) Frame.

10 foot (3.05 m) Door Transom Kit to Fit 10 foot (3.05 m) Door into 2 foot (0.61 M) Frame.

Finish: Spray paint coating is not acceptable.

** NOTE TO SPECIFIER ** Select the galvanized or powder coat from the following paragraphs and delete the one not required.

Galvanized.

Power Coat: Color as follows:

Custom as specified by the Architect.

** NOTE TO SPECIFIER ** Saf-T-Fence? partitions are a modular system of posts, wire mesh panels, and doors, with ample options in each. All components are manufactured for exact fit and easy assembly. These systems combine higher security, structural strength, and great flexibility.

Partition Assembly: Model Saf-T-Fence partitions as manufactured by Folding Guard. Provide to the size(s) indicated on the Drawing. Modular panels are available in the following sizes.

System 7 foot High: 7 foot (2.13 m) high post, 82 inch (2.08 M) high panel, and 7 foot (2.13 m) high door with pull handle, cylinder lock, and thumb turn. Includes a 2 inch (51 mm) sweep space under panel at floor level.

Panel Width:

10 inches (254 mm)

16 inches (406 mm)

19 inches (483 mm)

22 inches (559 mm)

28 inches (711 mm)

34 inches (863 mm)

46 inches (1168 mm)

58 inches (1473 mm)

System 8 foot High: 8 foot (2.4 m) high post, 94 inch (2.39 M) high panel, and 7 foot (2.13 m) high door and 11 inch (.28 m) transom with pull handle, cylinder lock, and thumb turn. Includes a 2 inch (51 mm) sweep space under panel at floor level.

Panel Width:

10 inches (254 mm)

16 inches (406 mm)

19 inches (483 mm)

22 inches (559 mm)

28 inches (711 mm)

34 inches (863 mm)

46 inches (1168 mm)

58 inches (1473 mm)

System 10 foot High: Starts with 8 foot (2.4 m) system and adds extension posts and panels as follows. 8 foot (2.4 m) system includes a 2 inch (51 mm) sweep space under panel at floor level.

Extension Panel Width:

10 inches (254 mm)

16 inches (406 mm)

19 inches (483 mm)

22 inches (559 mm)

28 inches (711 mm)

34 inches (863 mm)

46 inches (1168 mm)

58 inches (1473 mm)

70 inches (1778 mm)

94 inches (2378 mm)

Panel Construction: Panels shall be welded of No. 10 gauge (0.135 inch) (3.4 mm) steel wire in a 1-1/4 inches (32 mm) by 2-1/2 inches (64 mm) grid openings with wires securely welded to steel angle frames.

Vertical and horizontal frames shall be 1-1/2 inches (38 mm) by 1-1/2 inches (38 mm)14 gauge steel angle. Corner joint construction shall be a lap joint design, with one full width 3/16 inches (5 mm) weld at each corner junction.

Wire mesh panels to be supported by 2 inches square (51 mm) 16 gauge steel tube, welded to a 2 inches (61 mm) by 6 inches (152 mm) by 1/4 inch (6 mm) steel base plate.

Attachment of wire mesh partitions to posts is by four 1/4 (6 mm) inch by 2-1/2 inch (64 mm) carriage bolts furnished with the panel as standard.

Optional attachment of wire mesh partitions to posts to be accomplished by means of galvanized Drop-N-Lock System for ease of installation and removal for temporary egress to the work cell. Specify as required.

Sliding door frame shall be 1-1/2 inches by 1-1/2 inches (38 mm by 38 mm) 14 gauge angle on all four sides (full frame). Horizontal reinforcing at 42 inches (1067 mm) high shall be a formed 8 inch (203 mm) wide fender plate, welded in place with two angles 1 inch by 1 inch (25 mm by 25 mm) top and bottom, secured to side frames with a minimum of five weld points each side. Door shall be equipped with a heavy box track, two 2-1/8 inch (54 mm) diameter four-wheel ball bearing hangers, and bottom guide channel.

Hinged door frame shall be 1-1/2 inches by 1-1/2 inches (38 mm by 38 mm) 14 gauge angle on all four sides (full frame), with 1-1/2 inches (38 mm) pair of butt hinges. Horizontal reinforcing at 42 inches (1067 mm) high shall be a formed 8 inch (203 mm) wide fender plate, welded in place with two angles 1 inch by 1 inch (25 mm by 25 mm) top and bottom, secured to side frames with a minimum of five weld points each side.

Door Hardware:

All hardware included.

Door Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete those not required. Consult with factory for other options.

Built-in cylinder lock, keyed different, Standard.

Built-in cylinder lock, keyed alike.

Built-in double cylinder lock, keyed different.

ADA-compliant lock

Push-button lock

Electric strike/card reader locks

Interlock switches

Crash/panic bars

Spring hinges

Automatic closures

Service window.

Padlock hasp.

Panel roof to match wall panels.

Finish: Spray paint coating is not acceptable.

** NOTE TO SPECIFIER ** Select the galvanized or powder coat from the following paragraphs and delete the one not required.

Power Coat: Medium Gloss Black, Standard.

Power Coat: Color as follows:

Custom as specified by the Architect.

WOVEN WIRE MESH PARTITIONS

** NOTE TO SPECIFIER ** Wov-N-Wire? Partitions are the traditional enclosure system specified by Architects and Contractors. The 10-gauge steel wire is woven to create a durable, high-quality system that can be designed to any height up to 25 feet. With the ability to be configured into a 2-, 3-, or 4-sided room, Wov-N-Wire? Partitions can be used for a variety of applications, such as enclosing work areas or creating secure storage cages and stock rooms. The rooms can also be configured to include a roof or a service window.

Partition Assembly: Model Wov-N-Wire partitions as manufactured by Folding Guard. Provide to the size(s) indicated on the Drawing.

Modular Panel Sizes: Modular panels are available in the following sizes.

7 feet H by 1 foot W (2.13 M by 0.20 M)

7 feet H by 2 foot W (2.13 M by 0.61 M)

7 feet H by 3 foot W (2.13 M by 0.91 M)

7 feet H by 4 foot W (2.13 M by 1.22 M)

7 feet H by 5 foot W (2.13 M by 1.52 M)

8 feet H by 1 foot W (2.44 M by 0.20 M)

8 feet H by 2 foot W (2.44 M by 0.61 M)

8 feet H by 3 foot W (2.44 M by 0.91 M)

8 feet H by 4 foot W (2.44 M by 1.22 M)

8 feet H by 5 foot W (2.44 M by 1.52 M)

10 feet H by 1 foot W (3.01 M by 0.20 M)

10 feet H by 2 foot W (3.01 M by 0.61 M)

10 feet H by 3 foot W (3.01 M by 0.91 M)

10 feet H by 4 foot W (3.01 M by 1.22 M)

10 feet H by 5 foot W (3.01 M by 1.52 M)

12 feet H by 1 foot W (3.66 M by 0.20 M)

12 feet H by 2 foot W (3.66 M by 0.61 M)

12 feet H by 3 foot W (3.66 M by 0.91 M)

12 feet H by 4 foot W (3.66 M by 1.22 M)

12 feet H by 5 foot W (3.66 M by 1.52 M)

Adjustable Panel Sizes: Adjustable panels are available in the widths of 2.5 feet to 13 feet and heights of 7, 8, 10 and 12 feet.

Panel Construction:

Fabricated of No. 10 gauge steel wire with 1-1/2 inches (38 mm) diamond mesh grid openings.

Posts:

Line Posts: C-Channel, 1 inch by 3-1/2 inch by 1 inch (25 mm by 89 mm by 25 mm) with a 5 inch by 9 inch by 3/16 inch (127 mm by 229 by 4.8 mm) foot plate for each post.

7 feet 0 inches (2.13 M) H

8 feet 0 inches (2.44 M) H

10 feet 0 inches (3.01 M) H

12 feet 0 inches (3.66 M) H

Corner Posts: Angle, 1-1/4 inch by 1-1/4 inch (31.75 mm by 31.75 mm) with a 5 inch by 9 inch by 3/16 inch (127 mm by 229 by 4.8 mm) foot plate for each post.

7 feet 0 inches (2.13 M) H

8 feet 0 inches (2.44 M) H

10 feet 0 inches (3.01 M) H

12 feet 0 inches (3.66 M) H

Adjustable Corner Posts:

7 feet 0 inches (2.13 M) H

8 feet 0 inches (2.44 M) H

10 feet 0 inches (3.01 M) H

12 feet 0 inches (3.66 M) H

Door Spacer Posts:

7 feet 0 inches (2.13 M) H

8 feet 0 inches (2.44 M) H

10 feet 0 inches (3.01 M) H

12 feet 0 inches (3.66 M) H

Doors:

** NOTE TO SPECIFIER ** Select one or more of the following three Door paragraphs and delete those not required.

Hinged Doors:

Width:

** NOTE TO SPECIFIER ** Select one the following paragraphs and delete the one not required.

Single door, 3 foot (0.91 M) W.

Single door, 4 foot (1.22 M) W.

Pair doors, 3 foot (0.91 M) (two 3 foot W panels)

Pair doors, 4 foot (1.22 M) (two 4 foot W panels)

Height:

7 feet 0 inches (2.13 M) H Transom included.

8 feet 0 inches (2.44 M) H Transom included.

10 feet 0 inches (3.01 M) Transom included.

12 feet 0 inches (3.66 M) H Transom included.

Door Panel Construction: Fabricated of No. 10 gauge steel wire with 1-1/2 inches (38 mm) diamond mesh grid openings with wires securely fastened to 14 gauge steel frames.

Sliding Doors:

Type/Size:

** NOTE TO SPECIFIER ** Select one the following paragraphs and delete the one not required.

Single Sliding 3 foot (0.91 M) W Transom included.

Single Sliding 4 foot (1.22 M) W Transom included.

Single Sliding 5 foot (1.52 M) W Transom included.

Single Sliding 6 foot (1.83 M) W Transom included.

Single Sliding 5 foot (1.52 M) W by Full Height.

Single Sliding 6 foot (1.83 M) W by Full Height.

Single Sliding 8 foot (2.44 M) W by Full Height.

Single Sliding 10 foot (3.05 M) W by Full Height.

Pair Sliding 8 foot (2.44 M) W by Full Height consisting of two 4 foot wide panels.

Pair Sliding 10 foot (3.05 M) W by Full Height consisting of two 5 foot wide panels.

Door Panel Construction: Fabricated of No. 10 gauge steel wire with 1-1/2 inches (38 mm) diamond mesh grid openings with wires securely fastened to 14 gauge steel frames.

Track/Hangers: Door equipped with a heavy box track, two 2-1/8 inch (54 mm) diameter four-wheel ball bearing hangers, and bottom guide channel.

Door Hardware Options:

All hardware included.

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete those not required. Consult with factory for other options.

Padlock hasp.

Built-in cylinder lock, keyed different, Standard.

Built-in cylinder lock, keyed alike.

Thumbturn

Hydraulic Closer

Pushbar Exit Device

Lever Handle

Knob Handle

Electric Strike

Magnetic Lock

Keypad Lock

Proximity Reader

Magstripe Card Reader

Exit Button

Ceiling Panels:

Standard Partition Ceilings:

Standard: 10 feet L by 1 foot W (3.01 M by 0.20 M)

Standard: 10 feet L by 2 foot W (3.01 M by 0.61 M)

Standard: 10 feet L by 3 foot W (3.01 M by 0.91 M)

Standard: 10 feet L by 4 foot W (3.01 M by 1.22 M)

Standard: 10 feet L by 5 foot W (3.01 M by 1.52 M)

Odd Size Partition Ceilings: Up to the following sizes. Provide to exact size indicated on the Drawings.

6 feet H by 1 foot L (1.83 M by 0.20 M)

6 feet H by 2 foot L (1.83 M by 0.61 M)

6 feet H by 3 foot L (1.83 M by 0.91 M)

6 feet H by 4 foot L (1.83 M by 1.22 M)

6 feet H by 5 foot L (1.83 M by 1.52 M)

8 feet H by 1 foot L (2.44 M by 0.20 M)

8 feet H by 2 foot L (2.44 M by 0.61 M)

8 feet H by 3 foot L (2.44 M by 0.91 M)

8 feet H by 4 foot L (2.44 M by 1.22 M)

8 feet H by 5 foot L (2.44 M by 1.52 M)

10 feet H by 1 foot L (3.01 M by 0.20 M)

10 feet H by 2 foot L (3.01 M by 0.61 M)

10 feet H by 3 foot L (3.01 M by 0.91 M)

10 feet H by 4 foot L (3.01 M by 1.22 M)

10 feet H by 5 foot L (3.01 M by 1.52 M)

Ceiling Wall Angle and Fascia Bar: Provide as required to support entire perimeter of ceiling panels

Panel Construction:

Fabricated of No. 10 gauge steel wire with 1-1/2 inches (38 mm) diamond mesh grid openings.

Component Options:

** NOTE TO SPECIFIER ** Select the options required from the following paragraphs and delete those not required. Consult factory for additional information.

Wall Kit with 4 zinc-plated clamps and hardware.

Cut-Out Kit for cut-outs such as piping, etc.

T-Joint Kit for 3-panel intersection application.

T-Joint Kit for 3-panel intersection next to door.

Finish: Spray paint coating is not acceptable.

Power Coat: Color as follows:

Custom as specified by the Architect.

EXECUTION

EXAMINATION

Do not begin installation until substrates have been properly prepared.

If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

PREPARATION

Clean surfaces thoroughly prior to installation.

Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

INSTALLATION

Install in accordance with manufacturer's instructions.

Install plumb level, and securely anchored to floor and to other structural members where indicated.

Adjust doors for smooth, easy operation.

PROTECTION

Protect installed products until completion of project.

Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download