590 Super M - CNH Industrial
590 Super M
SERIES 3 LOADER/BACKHOE TIER III CERTIFIED
ENGINE
Model
Case Family IV 445TA/E3 diesel, Tier III certified
Type
4-stroke, turbocharged
Cylinders
4
Bore/Stroke
4.09 in x 5.19 in (104 x 132 mm)
Displacement
274 in3 (4.5 L)
Fuel injection
Direct high pressure common rail
Fuel
Diesel
Primary fuel filter
5 micron
Secondary fuel filter 30 micron w/water trap and indicating lamp
Air intake
Cross-flow
Cooling
Liquid
Engine speeds* (rpm)
Rated speed, full load Low idle High idle, no load
2200 900 - 1000 2330 - 2430
Horsepower
Gross Net
110 (82 kW) @ 2200 rpm 108 (81 kW) @ 2200 rpm
Maximum torque @ 1400 rpm
Gross
381 lb?ft (516 N?m)
Net
372 lb?ft (505 N?m)
Torque rise at rated speed
45%
NOTE: *Engine speeds with standard transmission. Meets federal emission regulations.
ENGINE COOLING
Radiator
Core type Core size area Rows of tubes
Square wave 487 in2 (.315 m2)
5
Fan
Style Diameter Ratio
Viscous 9 blade suction 19.2 in (488 mm) 1.4:1
Water pump Style
Integral
Engine oil
Pump
Deep sump plate cooler
with pressurized under-piston nozzles
Pump operating angle ratings
Side-to-side Fore and aft Oil filtration
Rated 35? Rated 35? Replaceable, full-flow cartridge
TIRES Front
2WD ? 14.5/75 x 16.1, 10-ply 4WD ? 14 x 17.5, 10-ply
Rear 2/4WD ? 21L x 24, 10-ply
POWERTRAIN
Transmission
4-speed synchromesh with hydraulically actuated clutches and electric F/R shuttle control, clutch disconnect buttons on the transmission shifter and loader control lever
Gear ratios 1st 2nd 3rd 4th
Forward 5.603 3.481 1.584 0.793
Reverse 4.643 2.884 1.313 0.657
Torque converter
Ratio
2.64
Differential lock
On-the-go push-button activation
Front 4WD axle Differential ratio Planetary hub ratio Total reduction ratio
2.130 6.0
12.78
Rear axle
Differential ratio
2.5
Planetary hub ratio
6.4
Total reduction ratio
16.0
Service brakes
Individually applied, power assisted, hydraulically actuated, maintenance-free, self-adjusting, outboard mounted, wet disc, 2 per side
Disc area
384 in2 (.25 m2)
Parking brakes Spring applied hydraulic release (SAHR)
Travel speeds ? mph (km/h)
1st 2nd
3rd 4th
Forward 3.9
6.2
13.4 24.6
(6.3) (10.0) (21.6) (39.5)
Reverse 4.7
7.4
16.1 29.5
(7.5) (12.0) (25.9) (47.4)
NOTE: Travel speeds at 2278 engine rpm.
ELECTRICAL
Voltage
12 volts, negative ground
Alternator
90 amp
Battery
850 cold-cranking amps
Optional batteries
(2) 850 cold-cranking amps
Power plugs
(2) 30 amps ea.
HYDRAULICS
Pump
Gear-type tandem, transmission driven coupled directly to engine
Main relief pressure
3050 + 50 - 50 psi @ 42.5 gpm (210 + 3 - 3 bar @ 161 L/min)
Filtration
7-micron, full flow replaceable cartridge on return line, condition indicator light for filter
Oil cooler
Heavy-duty
Loader flow @ rated engine rpm
31.5 gpm @ 3050 psi (119 L/min @ 210 bar)
Loader control valve
Monoblock single lever control for lift, tilt and auxiliary hydraulics, positive hold float and return-to-dig
Loader auxiliary hydraulics with proportional thumb switch w/detent on loader control handle
0 to 31.5 gpm (0 to 119 L/min)
Backhoe flow @ rated engine rpm
42.5 gpm @ 3050 psi (161 L/min @ 210 bar)
Manual Backhoe Controls
Backhoe Control Valve
Monoblock open-center, parallel circuits. Boom and dipper, with pilot operated checks
Backhoe auxiliary hydraulics
Uni-directional flow, adjustable variable flow from 0 to 36 gpm (136 L/min)
Control operation
Manual
Foot switch activated
Bi-Directional flow, variable flow from 0 to 42.5 gpm (161 L/min) @ rated engine rpm
Control operation
Manual
Hand lever
Page 1 of 6
OPERATOR ENVIRONMENT ROPS/FOPS canopy Key start Hydrostatic steering Vinyl air suspension seat w/180? swivel Seat turn around idle Electronic hand and foot throttles Ergonomic loader control lever w/push-button activation of differential lock and transmission de-clutch Backhoe foot-swing w/3 lever control (2) Accessory power plugs (30 amp) Anti-vandalism covers (canopy only) Cup holder Coat hook w/tether strap (cab only) Interior rearview mirror 2 in (51 mm) retractable seat belt Storage compartment w/lid Left side storage tray
INSTRUMENTATION Vehicle Control Module w/menu driven options and onboard diagnostics
Cruise control Foot throttle sensitivity Cold weather idle settings Maintenance settings Gauges Engine water temperature Converter oil temperature Fuel Tachometer/hourmeter Voltmeter Warning lights Air cleaner restriction Alternator A/C high pressure Cold start Engine oil pressure Hydraulic oil filter bypass Parking brake Low fuel Audible alarms w/diagnostics Coolant temperature Engine oil pressure Parking brake engagement Shuttle engagement/seat position Backup alarm Transmission temperature Water in fuel filter Battery voltage Low fuel Air filter restriction Hydraulic filter restriction A/C not functioning Horn - dual switched front & rear
TURNING DIAMETER
2WD
Brakes on Brakes off
25 ft 04 in (7.63 m) 25 ft 11 in (7.90 m)
4WD ? engaged Brakes on Brakes off
26 ft 5 in (8.04 m) 29 ft 10 in (9.08 m)
4WD ? disengaged Brakes on Brakes off
24 ft 8 in (7.51 m) 25 ft 6 in (7.78 m)
NOTE: Turning diameter dimensions curb to curb w/general purpose bucket.
OPERATING WEIGHTS
Lightest Configuration
Unit equipped with 2WD, ROPS canopy, vinyl
air suspension seat, 93 in (2.36 m) general pur-
pose loader bucket, 24 in (610 mm) Universal
backhoe bucket, standard dipperstick, 21L x 24
rear tires, 14.5/75 x 16.1 front tires, single bat-
tery, flip over stabilizer pads,
no operator
15,268 lb (6926 kg)
Heavy Configuration
Unit equipped with 4WD, cab, cloth air suspen-
sion seat, 93 in (2.36 m) 4 IN 1? loader bucket,
24 in (610 mm) Universal backhoe bucket,
Extendahoe? dipperstick, dual batteries, flip
stabilizer pads,
no operator
19,578 lb (8881 kg)
Add-on weights
Cab (over canopy)
+454 lb (206 kg)
Counterweights Extendahoe?
+440 lb (200 kg) +900 lb (408 kg)
+270 lb (122 kg)
4WD w/driveshaft guard
+393 lb (178 kg)
SERVICE CAPACITIES
Fuel tank
42.0 gal (159 L)
Hydraulic system Total Total w/Extendahoe?
Reservoir w/filter Reservoir w/o filter
32.2 gal (122 L) 33.7 gal (127.6 L)
12.5 gal (47.1 L) 12.0 gal (45.2 L)
Transmission 2WD Total system 4WD Total system
18 qt (17 L) 20.5 qt (19.4 L)
4WD Front axle Differential Planetaries (each)
7.1 qt (6.7 L) .63 qt (.6 L)
Rear axle Differential and planetaries 19.7 qt (18.6 L)
Engine oil w/filter
14.4 qt (13.6 L)
Cooling system w/heater w/o heater
19.0 qt (18.0 L) 18.3 qt (17.3 L)
Window washer reservoir
3.5 qt (3.3 L)
LOADER
Single-lever control for lift and tilt
Positive hold float
Return-to-dig
Automatic self-leveling
In-line, reverse linkage
Dual parallel dump cylinders
Clutch disconnect button on loader control and shift levers
Bucket position indicator
Loader Bucket Sizes
Width Weight Struck Heaped
General Purpose Bucket (w/ lift points and bolt-on cutting edge)
Width Weight Struck Heaped
93 in
1,123 lb 1.1 yd3 1.3 yd3
(2.36 m) (509 kg) (0.84 m3) (1.0 m3)
96 in
1,324 lb 1.27 yd3 1.5 yd3
(2.44 m) (601 kg) (0.97 m3) (1.15 m3)
4 IN 1? Bucket
93 in
1,628 lb
(2.36 m) (738 kg)
1.0 yd3
1.2 yd3
(0.76 m3) (0.92 m3)
BACKHOE
Over-center design
Cast, ductile iron boom, and swing tower
Open-center hydraulics - Pro Control System
17, 940 lb?ft (24 370 N?m) swing torque
Case attachment coupler
Foot-swing w/3 lever control
Wing stabilizers w/flip over dirt pad
Backhoe Bucket Sizes
Width
Weight
Heaped
Universal Buckets
12 in (305 mm)
290 lb (132 kg)
3.40 ft3 (0.10 m3)
16 in (406 mm)
346 lb (157 kg)
3.60 ft3 (0.10 m3)
18 in (457 mm)
350 lb (159 kg)
5.30 ft3 (0.15 m3)
24 in (610 mm)
413 lb (187 kg)
7.70 ft3 (0.22 m3)
30 in (762 mm)
475 lb (215 kg)
10.20 ft3 (0.29 m3)
36 in (914 mm)
535 lb (243 kg)
12.70 ft3 (0.36 m3)
High Capacity Buckets
24 in (610 mm)
450 lb (204 kg)
8.50 ft3 (0.24 m3)
30 in (762 mm)
517 lb (235 kg)
10.60 ft3 (0.30 m3)
590 Super M Page 2 of 6
J
D
A
N
B
HE
O
L
M
LOADER DIMENSIONS
A. Overall operating height ? fully raised
Height to ?
B. Bucket hinge pin fully raised
C. Bucket hinge pin @ SAE carry
D. Dump angle @ full height
E. Dump clearance @ full height, 45? dump ?
Bucket Clam open
F. Dump reach @ full height, 45? dump ?
Bucket Clam open
Bucket rollback ?
G. @ groundline
H. @ SAE carry
J.
@ full height
K. Digging depth below grade ?
Bucket flat Clam open (dozing)
L. Reach from front axle centerline ? bucket on ground
Lift capacity to full height
Breakout force ?
Lift cylinders
Dump cylinders
Bucket cutting edge width
Maximum grading angle
Maximum clam opening
Moldboard height
Raising time to full height
Bucket dumping time
Lowering time ?
Power down
Return-to-dig
Clam ?
Open time
Close time
NOTE: Loader dimensions taken with 4WD.
General Purpose Bucket* 14 ft 2 in (4.32 m)
11 ft 5 in (3.47 m) 13.7 in (349 mm)
45?
9 ft 0 in (2.75 m) NA
27.5 in (699 mm) NA
40? 45? Adjustable
3.8 in (96 mm) NA
77.6 in (1.97 m) 7,327 lb (3323 kg)
10,729 lbf (47 725 N) 10,980 lbf (48 841 N)
93 in (2.36 m) 116? NA NA
4.7 sec 1.2 sec
2.8 sec 3.1 sec
NA NA
590 Super M Page 3 of 6
C G
K
4 IN 1? Bucket 14 ft 6 in (4.43 m)
11 ft 5 in (3.47 m) 14.9 in (379 mm)
45?
9 ft 2 in (2.78 m) 9 ft 10 in (3.0 m)
25.9 in (659 mm) 11.5 in (293 mm)
40? 45? Adjustable
4.3 in (109 mm) 1.7 in (42 mm)
75.2 in (1.91 m) 7,437 lb (3373 kg)
10,294 lbf (45 790 N) 12,004 lbf (53 396 N)
93 in (2.36 m) 116?
38.3 in (972 mm) 36.8 in (934 mm)
4.7 sec 1.2 sec
2.8 sec 3.1 sec
2.3 sec 2.3 sec
DIMENSIONS
M. Overall transport length ? General purpose bucket 4 IN 1? bucket
Overall transport width Height ?
To top of canopy To top of cab To top of exhaust stack N. Transport Ground clearance at backhoe frame Angle of departure Front wheel tread ? 2WD 4WD Rear wheel tread O. Wheelbase ? 2WD 4WD
Standard Backhoe
23 ft 7 in (7.13 m) 22 ft 7 in (6.88 m)
7 ft 9 in (2.36 m)
8 ft 11 in (2.73 m) 8 ft 10 in (2.69 m)
8 ft 7 in (2.62 m) 11 ft 2 in (3.41 m) 14.6 in (371 mm)
23?
72.6 in (1.84 m) 73.4 in (1.86 m) 69.9 in (1.78 m)
84 in (2.13 m) 84.5 in (2.15 m)
Retracted
Extendahoe? Extended
23 ft 7 in (7.19 m)
NA
22 ft 8 in (6.91 m)
NA
7 ft 9 in (2.36 m)
NA
8 ft 11 in (2.73 m) 8 ft 10 in (2.69 m)
8 ft 7 in (2.62 m) 11 ft 7 in (3.54 m)
14.8 in (375 mm)
23?
8 ft 11 in (2.73 m) 8 ft 10 in (2.69 m)
8 ft 7 in (2.62 m) NA
14.8 in (375 mm)
23?
72.6 in (1.84 m)
NA
73.4 in (1.86 m)
NA
69.9 in (1.78 m)
NA
84 in (2.13 m)
NA
84.5 in (2.15 m)
NA
NOTE: Dimensions taken with 21L x 24 rear tires and 14.5/75L x 16.1 front tires except that data marked 4WD is taken with 14 x 17.5 front tires.
CYLINDERS
Loader Lift (2) Bucket (2) 4 IN 1? clam (2)
Backhoe Boom Dipperstick Bucket Extendahoe? Swing (2) Stabilizer (2)
Steering 2WD 4WD
Bore Diameter
3.5 in (89 mm) 3.25 in (83 mm)
3.0 in (76 mm)
5.5 in (139.7 mm) 5.5 in (139.7 mm)
3.75 in (95 mm) 3.0 in (76 mm)
4.0 in (101.6 mm) 5.0 in (127 mm)
2.75 in (69.9 mm) 2.48 in (63 mm)
Rod Diameter
1.75 in (44.5 mm) 1.75 in (44.5 mm) 1.75 in (44.5 mm)
2.5 in (63 mm) 2.75 in (69.9 mm) 2.75 in (69.9 mm) 1.75 in (44.5 mm)
2.0 in (50.8 mm) 2.25 in (57.2 mm)
1.5 in (38.1 mm) 1.5 in (38.1 mm)
Stroke
30.2 in (766 mm) 20.6 in (522 mm)
9.1 in (231 mm)
38.4 in (976 mm) 22.2 in (564.2 mm)
34.3 in (872 mm) 48.0 in (1.22 m)
11.5 in (292 mm) 20.4 in (519.4 mm)
6.7 in (170 mm) 9.53 in (242 mm)
590 Super M Page 4 of 6
BACKHOE LIFT CAPACITIES Standard Backhoe
Boom Lift
Distance from swing pivot (m)
+18 ft (5.48 m)
+16 ft (4.87 m)
+14 ft (4.27 m) 9 ft 9 in (2.97)
+12 ft (3.66 m) 12 ft 1 in (3.69)
+10 ft (3.05 m) 13 ft 8 in (4.16)
+8 ft (2.44 m) 14 ft 8 in (4.47)
+6 ft (1.83 m) 15 ft 3 in (4.65)
+4 ft (1.22 m) 15 ft 8 in (4.77)
+2 ft (0.61 m) 15 ft 10 in (4.82)
Ground Level
15 ft 7 in (4.75)
-2 ft (0.61 m)
15 ft 1 in (4.60)
-4 ft (1.22 m)
14 ft 4 in (4.37)
-6 ft (1.83 m)
13 ft 2 in (4.01)
-8 ft (2.44 m)
11 ft 5 in (3.48)
-10 ft ft (3.05 m) 8 ft 9 in (2.67)
-12 ft (3.66 m)
-14 ft (4.27 m)
-15 ft (4.57 m)
Dipper Lift
+16 ft (4.87 m)
+14 ft (4.27 m) 9 ft 5 in (2.87)
+12 ft (3.66 m) 10 ft 7 in (3.23)
+10 ft (3.05 m) 11 ft 0 in (3.35)
+8 ft (2.44 m) 10 ft 7 in (3.23)
+6 ft (1.83 m)
9 ft 4 in (2.84)
+4 ft (1.22 m)
6 ft 0 in (1.83)
Backhoe lift capacity ? lb (kg)
2,870 (1302) 3,590 (1628) 3,670 (1665) 3,670 (1665) 3,620 (1642) 3,550 (1610) 3,460 (1569) 3,370 (1529) 3,330 (1510) 3,250 (1474) 3,110 (1411) 3,040 (1379) 2,960 (1343) 2,960 (1343) 2,930 (1329)
4,800 (2177) 5,290 (2399) 5,580 (2531) 5,750 (2608) 5,630 (2554) 6,490 (2944)
Boom and Dipper Lift Capacities are rated per SAE J31 and are 87% of the maximum
hydraulic lift force available with the specified options.
Extendahoe?
Retracted
Extended
Distance from swing pivot (m)
Backhoe lift capacity ? lb (kg)
Distance from swing pivot (m)
Backhoe lift capacity ? lb (kg)
1,940 (880)
13 ft 6 in (4.11)
2,200 (998)
10 ft 8 in (3.25)
3,310 (1501)
15 ft 5 in (4.70)
2,300 (1043)
12 ft 9 in (3.89)
3,280 (1488)
16 ft 10 in (5.13)
2,420 (1098)
14 ft 2 in (4.32)
3,410 (1547)
17 ft 11 in (5.46)
2,370 (1075)
15 ft 2 in (4.62)
3,330 (1510)
18 ft 9 in (5.72)
2,420 (1098)
15 ft 11 in (4.85)
3,390 (1538)
19 ft 3 in (5.87)
2,420 (1098)
16 ft 3 in (4.96)
3,280 (1488)
19 ft 7 in (5.97)
2,310 (1048)
16 ft 4 in (4.98)
3,210 (1456)
19 ft 8 in (5.99)
2,290 (1039)
16 ft 1 in (4.91)
3,120 (1415)
19 ft 6 in ft (5.94)
2,260 (1025)
15 ft 8 in (4.77)
3,010 (1365)
19 ft 2 in (5.84)
2,230 (1012)
14 ft 11 in (4.55)
2,950 (1338)
18 ft 6 in (5.64)
2,220 (1007)
13 ft 9 in (4.19)
2,850 (1293)
17 ft 8 in (5.38)
2,140 (971)
12 ft 2 in (3.71)
2,840 (1288)
16 ft 6 in (5.03)
2,110 (957)
9 ft 10 in (2.99)
2,810 (1275)
14 ft 10 in (4.52)
2,090 (948)
5 ft 8 in (1.72)
2,880 (1306)
12 ft 9 in (3.89)
2,180 (989)
9 ft 9 in (2.97)
2,240 (1016)
6 ft 0 in (1.83)
2,490 (1129)
10 ft 2 in (3.10) 11 ft 2 in (3.40) 11 ft 6 in (3.50) 11 ft 2 in (3.40) 10 ft 1 in (3.08) 7 ft 4 in (2.23)
4,850 (2200) 5,310 (2409) 5,510 (2500) 5,720 (2595) 5,740 (2604) 6,590 (2989)
12 ft 10 in (3.91) 14 ft 0 in (4.27) 14 ft 7 in (4.45) 14 ft 9 in (4.50) 14 ft 8 in (4.47) 14 ft 0 in (4.27) 12 ft 9 in (3.89)
2,810 (1275) 2,940 (1334) 3,080 (1397) 3,100 (1406) 3,150 (1429) 3,190 (1447) 3,290 (1492)
BACKHOE OPERATIONAL DATA
Digging depth ? Maximum Maximum w/hi-capacity bucket 2 ft (610 mm) flat bottom 8 ft (2.44 m) flat bottom
Overall reach from ? Rear axle centerline Swing pivot
Loading height Loading reach ? dipper retracted Swing arc 1 Bucket rotation ?
#1 position #2 position Stabilizer spread ? operating Digging force ? Bucket cylinder Dipper cylinder
Leveling angle maximum slope that backhoe will make vertical cut
Standard Backhoe
15 ft 11 in (4.85 m) 16 ft 4 in (4.98 m) 15 ft 10 in (4.83 m) 14 ft 11 in (4.55 m)
23 ft 3 in (7.09 m) 19 ft 8 in (5.99 m) 11 ft 5 in (3.48 m) 9 ft 6 in (2.90 m) 80?
164? 200? 11 ft 1 in (3.38 m)
14,718 lbf (65 469 N) 8,449 lbf (37 583 N) w/bucket @ 50?
12?
Retracted
Extendahoe? Extended
15 ft 11 in (4.85 m) 16 ft 4 in (4.98 m) 15 ft 10 in (4.83 m) 14 ft 11 in (4.55 m)
19 ft 11 in (6.07 m) 20 ft 4 in (6.20 m) 19 ft 10 in (6.05 m) 19 ft 2 in (5.84 m)
23 ft 3 in (7.09 m) 19 ft 8 in (5.99 m) 11 ft 5 in (3.48 m) 9 ft 6 in (2.90 m) 180?
27 ft 2 in (8.28 m) 23 ft 7 in (7.19 m) 13 ft 9 in (4.19 m) 12 ft 9 in (3.89 m) 180?
164? 190? 11 ft 1 in (3.38 m)
14,718 lbf (65 469 N) 8,449 lbf (37 583 N) w/bucket @ 50?
164? 190? 11 ft 1 in (3.38 m)
14,718 lbf (65 469 N) 5,999 lbf (26 685 N) w/bucket @ 51?
12?
12?
NOTE: Lift capacities apply straight to the rear of prime mover. Equipped with 24 in (610 mm) Universal H.D. trenching bucket and Case coupler except as noted.
590 Super M Page 5 of 6
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- battery service
- volvo 850 engine service and adjustment specifications
- 590 super n coleman equipment
- c specifications turbo
- product specification trojan battery company
- the right battery chrysler
- one brand to satisfy every customer battery sales
- skytrak 10054 specifications one source
- motorcraft bxt batteries
- 590 super m cnh industrial