SECTION 06200: INTERIOR FINISH CARPENTRY



SECTION 06200: INTERIOR FINISH CARPENTRY

PART I. GENERAL

1.1 SCOPE

a. Finish carpentry items, architraves, soffits, fascias

b. Wood door frames set into partition.

c. Wood casings and moldings.

d. Hardware and attachment accessories

2. SUBMITTALS

a. See section – Administrative requirements for submittal procedures

PART II. PRODUCTS

2.1 GENERAL

a. Trim and moulding shall be of size and shape as shown on the Drawings

and/ or Finish Schedule.

b. Lengths shall be maximum lengths available. No piecing is permitted on

runs of less than 14 feet.

c. Mouldings to be used in one space must be from the same mill run to

ensure uniformity of size and shape.

2.2. PROJECT CONDITIONS

a. Sequence installation to ensure utility connections are achieved in an orderly and expeditious manner.

b. Coordinate the work with installation of associated and adjacent components.

2.3. WOOD-BASED COMPONENTS

a. Wood fabricated from old growth timber is not permitted.

2.4. LUMBER MATERIALS

a. Softwood Lumber: sawn, maximum moisture content of 6 percent; with vertical grain.

b. Hardwood Lumber: sawn, maximum moisture content of 6 percent; with vertical grain, of quality suitable for transparent finish.

2.5 ADHESIVE

a. Adhesive: Type recommended by laminate manufacturer to suit application.

2.6 FASTENERS

a. Fasteners: Of size and type to suit application

b. Concealed Joint Fasteners: Threaded steel.

2.7 ACCESSORIES

a. Primer: Alkyd primer sealer type.

b. Wood Filler: Solvent base, tinted to match surface finish color.

2.8 WOOD TREATMENT

a. Fire Retardant Treatment (FR-S Type): Chemically treated and pressure impregnated; capable of providing flame spread index of 25, maximum, and smoke developed index of 450, maximum, when tested in accordance with ASTM E84.

b. Wood Preservative (Surface Application): Clear

c. Provide identification on fire retardant treated material.

2.9 FABRICATION

a. Shop assemble work for delivery to site, permitting passage through

building openings.

b. When necessary to cut and fit on site, provide materials with ample allowance for cutting. Provide trim for scribing and site cutting.

PART 3 EXECUTION

3.1 INSTALLATION

a. All trim shall be installed with nails of appropriate size to penetrate

substrate 3/4". Nails shall be set and all bolts and screws countersunk.

Spacing of nails shall be as required to hold trim tight and flat to surface.

b Special nailing patterns shall be as noted on the Drawings or as per approved samples and mock-ups.

c. All miters and joints are to be biscuited and glued.

d. All finish nails shall be countersunk.

e. Trim shall be installed with the longest possible lengths:

1 Stagger splice joints in long runs where trim is built up of multiple

pieces. Stagger joints by at least 4 feet.

2 Carefully lay out splice joints equally at long runs. Joints shall be a

center of run or equidistant from ends.

3. Install wood doors per the requirements of Section 08210.

4. All base, crown molding and other linear trim shall be mitered at outside

corners.

5. All base, crown molding and other linear trim shall be coped and fit at inside

corners.

6. Millwork and cabinets shall be installed per the requirements

3.2 SITE APPLIED WOOD TREATMENT

a. Apply preservative treatment in accordance with manufacturer's instructions.

b. Brush apply one coats of preservative treatment on wood in contact with cement based materials. Treat site-sawn cuts.

c. Allow preservative to dry prior to erecting members.

3.3 PREPARATION FOR SITE FINISING

a. Prior to shop or field priming, all trim shall be sanded free of all planner

marks where smooth finish is called for.

b. Set all nails and fasteners and fill holes after sealing.

c. Clean all glue from joints as work is being done.

3.4 ERECTION TOLERANCES

a. Maximum Variation from True Position: 1/16 inch (1.5mm)

3.5 SCHEDULE

a. Exterior:

(1) Enclosing soffit spaces – as detailed

(2) Soffits and fascias – prepare for paint finish

b. Interior

1) Door, Glazed Light, and Pocket door frames: White Birch; prepare for paint finish

END OF SECTION 06200

SECTION 06410: CUSTOM CABINETRY

PART I. GENERAL

1.1 All materials in this section to be supplied by Client. Refer to manufacturer’s specifications for installations

2. SUBMITTALS

a. See section – Administrative requirements for submittal procedures

b. Refer to Manufacturer’s Shop drawings: Indicate materials, component profiles and elevations, assembly methods, joint details, fastening methods, accessory listings, hardware location and schedule of finishes.

3.2 INSTALLATION

a. All components shall be set true, plumb, and level with no distortions.

Shim as required using concealed shims. Scribe and fit work to adjoining

work and existing surfaces (i.e. walls, floors, ceilings, etc.). All work is to

be securely and rigidly fastened in place.

b. Decking shall be attached with:

1 Exposed decking nails

2 Decking screws

3 Concealed nailing clips and galvanized nails.

4. Nailing shall be concealed wherever possible.

c. Trim shall be installed with the longest possible lengths:

1 Stagger splice joints in long runs where trim is built up of multiple

pieces. Stagger joints by at least 4 feet.

2 Carefully layout splice joints equally at long runs. Joints shall be a

center of run or equidistant from ends.

3.3 PREPARATION FOR FINISHING

a. Prior to shop or field priming, all trim shall be sanded free of all planner

marks where smooth finish is called for.

b. Set all nails and fasteners.

c. Clean all glue from joints as work is being done.

3.4 PROTECTION AND JOB CLOSEOUT

a. Protect all finished trim work from damage before, during and after

installation.

b. Replace any work that is damaged beyond repair.

c. At job closeout, check all trim and siding for defects. Repair or replace as

required.

d. Re-work miter joints that have opened during the course of the project.

END OF SECTION 06410

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download