Cnc controller manual rev1.doc - Techserv Profile Machines ...
Techserv CNC Controller
Operator Manual
rev3
Overview
2. Main Screen
3.Homing
4.Flexi shapes
5.Load Shape
6. Cutting with Plasma
Setup screen
Saving Data
Nesting
Plate Align
Origin Screen
Cut Screen
Making a cut
Test Run
Stepping through pierces
Other features
What to do if
Arc Voltage Controls
7. Cutting with Gas
Setup screen
Cut Screen
What to do if
8. Jog Functions
Standard Jog
Relative/Absolute Jog
Repeat Direction
9. Manual Cut
Plasma
Gas
10.Diagnostics
Overview
The Techserv CNC system is a intuitive PC based controller designed specifically for 2D cutting using plasma, gas and water jet processes.
The Controller can be retrofitted to upgrade older machines.
Selecting material thickness, type and cutting current automatically sets cutting speed, initial height, cutting height, pierce delay, arc voltage height etc.
When used in conjunction with a suitable Plasma, gas pressures / flow and cutting current are automatically controlled.
When flame cutting, oxygen pre-heat and cut pressures are automated.
Cutting speed can be varied on the fly, along with all height sense parameters, oxygen pressure etc
The CNC system produces a daily log file, detailing most functions including, cut on, gas on, job running, job name, screen name etc. Data is logged per second and an off line viewing programme gives an easy to read visual indication of activity together with a job list and timings.
Comprehensive diagnostics and test screens allow all functions to be checked. Network connectivity provides for remote log-in and faut finding.
Numerous drawing file types can be imported, including ESSI, Word Address, GCode and DXF etc. Parts can be previewed prior to selection and rotated, mirrored and scaled if necessary.
The ‘Flexi Shape’ facility incorporates a range of templates, from rectangles and rings through to lugs and floor plates. Selecting a generic shape and following the simple dimension prompts creates a part that can be nested, cut and saved with no further programming.
The ‘Manual Cut’ facility enables basic control of the cut process and point to point cutting. Normally automated processes ie. Cut speed, height sense etc are maintained.
Semi automatic nesting fills plates with minimum wastage, allowing multiple parts to be cut from a sheet. Also row and column array nesting with adjustable scrap allowance make the most use of the plate.
Super-Hole Technology optimises plasma hole cut quality for ‘bolt ready’ holes.
Main Screen
Starts the controller software
Exits the program & shuts down Windows
Exits to Desktop
Displays system information, motion controller serial number, power cycles & version of software installed
In this state the controller is not running and the drives are disabled.
To start the controller press Press to Start.
This will take you to the Main Screen
Home Status This will flash a red error message until the machine is homed and in the case of 3 axis machines squared.
Status Pane Shows if any of the software or hard limits have been activated.
Flexi Shape Allows the operator to create shapes from the parts library within the controller.
Load Shape Allows the operator to load a shape from an external source, from either a memory stick or over a wired or wireless net work.
Scan and Nest (Optional includes simple CAD). Allows scanning of drawings into software to be cut and or edited. (requires camera).
Process Allows adjustment of gas pressures if required.
Jog Moves cutting torch to any point on the bed.
Manual Cut Used for removing scrap, point to point and strip cutting.
Configure Changes setting such as plasma ,type, homing, encoder
calibration etc.
Exit Returns to previous screen.
Home routine Homes the machine and allows access to the preset table positions.
Emergency Stops
The machines will be fitted with a number of emergency stops. When operated the machine will stop and the cutting process will be interrupted. The red stop screen will appear barring any further input until the Emergency stop has been returned to a normal operating state. If necessary the exit controller button can be used to close down the software and return to the Windows desktop.
Homing
The machine should be homed before cutting commences. This will ensure the machine soft limits are operational and the axis have the correct alignment.
After pressing the home routine button the following screen will appear.
Use the Jog buttons to position the machine near the pre-set home points.
Press the Start routine button
The machine will find the home switch points, depending on the machine type the the home sequence should be as follows:
The plasma height sensing head will home
Home X axis
Home Y and YY axis
Apply square offset.
When the machine has homed all axes, the following screen will appear, with additional buttons revealed.
After this point you do not have to home the machine again unless you suspect the machine is out of square or you have exited the program.
There are 4 preset table positions ( set via the configuration screen) to move the torch to one of these, i.e. to unload, ensure the bed is clear of obstructions and select the desired table position. The machine will traverse to selected point.
The movement can be halted by pressing Stop.
Lost cut recovery
This feature retains the origin coordinates for the last few jobs cut. It is used if the machine is inadvertently shut down, or the job has been stopped before completion.
If there has been a power loss investigate the reason for this and the subsequent shut down of the system. Once satisfied the fault has been rectified restart the controller.
Carry out the home routine as normal.
Once the home routine is complete using the drop down control select the job required from the list.
Press the lost cut recovery button.
The machine will now move to the origin of the last plate cut.
From this point load the shape / nest as normal and advance around the pierce points / cut path to continue cutting. These functions will be explained in tsubsequent sections.
To exit the homing screen and return to the main screen press Exit
Flexi Shapes
These are a series of pre defined shapes which can be dimensioned by the operator.
Press the Flexi Shape button.
Press the icon of the desired shape.
A picture of the selected shape will appear together with a series of prompts and a keypad.
Enter the required measurements using the keypad.
Other parameters include:-
Lead in - distance from pierce to cut path
Start position - position of pierce.
When all dimensions have been input the following screen or similar will be displayed.
From this screen it is possible to alter any mistakes or customise the shape further.
To change an overall dimension highlight the required value on the screen, the key pad will appear. Type in the new value, press ‘enter’. The value will displayed and the overall sketch will change to show new dimensions.
It is possible to alter each corner individually
Refer to the numbered buttons around the shape in this case 1 to 4 are the outer corners and 5 to 8 are the inner corners.
To modify the upper right corner press the dimension next to the number 1
The keypad will appear type in the desired dimension ie 25 mm
To alter the style of the corner press the corresponding corner style button this will toggle between outside radius, inside radius and chamfer
All corners can be modified individually to give maximum flexibility.
Once the shape is as desired press Next to move on to the preview screen
Preview Screen
This screen shows a preview of the flexi shape or loaded part.
Rotate
Rotates shape through -360 to 360 degrees.
Press rotate, the keypad will appear, type in value then press enter.
The preview will be modified and the value entered will appear in the box.
Scale
The scale multiplier makes the shape larger or smaller.
Press scale and enter the scale factor required, followed by enter. The preview will be updated.
Mirror
Mirrors the shape around different axes. Pressing Mirror toggles between mirror X , mirror Y,mirror X &Y and No mirror. The mirror status is displayed below the button an the preview modified.
Mini Nest
Certain shapes can be inter linked to make for more efficient cutting. This mode can be used to manually link 2 of the same shape together. This can be combined with standard row and column nesting, accessed via the process setup screen.
Cut one part
This feature allows a single part to be selected from a nest of parts and then cut or re nested. This is used when a part has been lost or damaged by subsequent processing. Simply selectCut one part and press the part required.
Load Shape
This allows the operator to load pre designed nests from an external source such as a memory stick or network.
From the main menu screen press Load shape.
A list of available files will be displayed.
Use up / down to select the required file, after a brief pause, a thumbnail will be generated. If this is the correct nest press select.
If the desired drive is not shown, press the change drive button and use the up / down button to highlight the required drive, then press select.
If there are many nests available to download, press the Sort button and type in the first few letters / numbers of the required nest and press enter. From the abridged list use up / down to highlight the required file and press select.
This will open the Preview screen - this operates in exactly the same way as described previously for the Flexi shape operations
Numeric Sort
Files are listed alpha numerically, selecting Numeric sort will toggle the list to file creation date.
Change Drive
Lists all drives that the computer can access, this will show all internal drives and any memory sticks or available networks.
Sort
If many nests are available for downloading, scrolling through the list can be time consuming. Pressing Sort will open an alpha numeric keyboard, part or all of the file name can then be typed in thus, narrowing the search.
Up and Down
Moves cursor through the available drives or files displayed on the screen.
Select
Selects the required drive file highlighted on the screen.
Exit
Exits back to the main screen.
Directory & File name
Displays path and file selected.
Delete
Deletes selected file (this option may not be available in certain configurations)
Preview
Generates a “thumbnail” sketch of the nest . Please note if this button is pressed when a directory is selected it will generate previews for all the nests within that directory, which may take some time depending on the number of nests and their complexity.
Tip
The initial search path is defined within the configuration, if an alternative file path is regularly used, this path can be set to default as follows.
Press the Change drive button and use the up / down button to highlight the required drive, then press select.
A list of available directories will appear, use the up / down buttons to highlight the desired directory, then press Select. Pressing Make Default will complete the operation.
Setup Job screen
The procedure for cutting with plasma is the same for both flexi shapes and loaded shapes
The controller features an expert system, which will automatically set cutting speed, arc voltage, pierce height etc. As there are many factors that effect these settings - plate quality and type etc the operator can tailor these setting to suit the application and if required,save the settings permanently.
Press the buttons to select the current and material required, the system will hilight the relevant information in the cutting table and the consumable chart will change automatically.
Press the material thickness display and the keypad will appear, type in the thickness to be cut and press enter.
The information for the thickness will be highlighted and the cutting speed etc will be set automatically.
Tip
To add a different thickness or modify existing data.In this example information for 12mm material thickness will be addedIn the material thickness box enter 12 then press enter Press Save Data
At this point, if no changes are required simply press Next to proceed to the Cut screen.
Super Hole
This feature identifies round holes within a profile and automatically applies a predefined algorithm to improve the 'roundness' of the hole and reduce the edge taper. The height sense is also frozen and cutting speed adjusted.
Pressing super hole will toggle the action on and off.
Once all changes have been made on the Set up Screen
Press next to move to the Origin Screen.
Save Data
If required most parameters can be modified and set to replace the default settings. To do this press the save data button.
The screen shown above will appear, press the parameter to be changed, the keypad will appear, type in the new value and press enter.
Parameters that can be changed are:-
Speed - Cutting speed.
Kerf - Allowance for width of the process.
Plasma - Plasma gas pressure, for HPR systems only.
Shield - Shield gas pressure, for HPR systems only.
Preflow - preflow gas pressure, for HPR systems only.
Arc voltage - the arc voltage measured by the height sense (if fitted) the higher the value the larger the distance above the plate.
Cut height - the height above the plate that the height sense (if fitted) moves to once the arc is detected, prior to Arc voltage sensing activating.
Pierce height - The distance above the plate the height sense (if fitted) moves to prior to piercing. Generally twice the cut height.
Pierce delay (seconds) - Time machine waits before starting movement to allow plasma arc to pass through the plate.
Early Off (ms) - Time before end of cut path the plasma is turned off to prevent damage to end of part and increase consumable life.
Delay before AVC comes on – allows the arc to stabilise before arc sensing starts.
Raise on pierce mm – Raises the torch by the amount entered. This takes place just after the arc is established, prior to motion commencing. Raising the torch will reduce the amount of spatter hitting the torch and by setting the raise on pierce to x seconds will allow the torch to remain at the raised height before lowering to cut height, thus avoiding the molten spatter pool.
Raise on pierce for x seconds -This feature is used in conjunction with the raise on pierce mm parameter.
When all parameters are set press save
Saving Data will appear briefly on the screen to confirm the setting have been saved. The Set up screen will now reappear.
To discard changes press Next.
Nesting
The controller has a row and column nesting facility built in, this can be used with all shapes, flexi or downloaded.
Press the Vertical and / or Horizontal boxes and type in the required quantities. The scrap allowance is used to adjust the distance between the components. Note the scrap allowance is in addition to the lead in line and can be set to a negative value to move parts closer together.
Once required number of parts are nested press Next to return to the setup screen.
Other options are:
Standard / Cut Inter component moves - Standard turns off cut between pierces so parts can be chain cut. Warning proceed with caution this function can only be used on parts with No internal cut outs.
Stagger - Gives better plate usage when cutting circles.
Mirror/ Rotate - Allows nest to be manipulated by rotating and mirroring.
Save Nest - if the nest is to be cut several times it can be saved to prevent having to re input it again. The nest is given a name and can then be reloaded from the saved nest directory on the C drive.
Zoom In /Out - Toggles Zoom mode. If the screen is touched the view will zoom in or out to view nest.
Redraw - Returns to original view.
Next - Returns to Setup page.
Plate Align
The plate align function allows the operator to take in to account if a plate is not parallel to the bed or rail.
Press the Plate Align Button
Follow the on screen instructions and press Done to go back to the setup screen.
This information will be retained until another plate alignment is carried out, allowing multiple nests to be cut from the same plate.
Note the plate align data will only be used on proceeding plates if the Plate align Button is pressed otherwise the plate will be cut with no angular correction.
Once all changes have been made on the Set up Screen press next to move to the Origin Screen.
The controller calculates the maximum area of the shape. The origin is the point that best defines the position of the cutting torch to the plate. When cutting nests from whole sheets this position will generally be the same each time, depending on machine configuration. However when cutting pieces from part plates it is sometimes easier to align to a good edge, from this position the machine will traverse to the first pierce point (optional centre origins are shown in this view).
Press the relevant origin to select it. This will move to the cut screen
The indicators and controls on the run screen have the following functions:
Motion pane
X & Y position indicator
Manual speed adjust + - speed
Speed indicator upper : program speed Lower indicator : running speed
Cycle Start/Stop : starts and stops the cutting process
Reverse : reverses the cutter around the cut path
Advance : advances the cutter around the cut path
To pierce / origin : the first press returns the cutter to the last pierce, the second press returns to the origin point of the nest.
Fwd / Rev : moves the cutter forward and reverse through the pierce points
Jog select
Test / Cut mode select : switches between cut mode and test mode
Nest view / Zoom view : toggles between nest and zoom view, pressing the nu meric button increases the zoom level further
Limit status pane : shows the limit and cut status
Optional Arc Voltage pane
AVC on / off
Initial Height sense on / off
Manual raise / lower of the cutting head
Arc Voltage increase / decrease
Set Arc Volts : displays the programmed arc voltage
Actual Arc Volts : displays the actual arc voltage when cutting
Graphical display area
This shows the profile being cut. The black line is the original geometry, the white line is the cutter path. Internal lines are shown in blue, secondary processes are shown in purple.
The yellow rectangle represents the extents of the box.
The graphical display area is interactive and pressing the screen causes the view to zoom in, in certain modes pressing the screen selects a pierce point.
Process pane
Cut Indicator :
In gas mode the gas on, hi preheat, and automatic / manual selection buttons are also displayed.
Exit pane
Reload Nest : reloads nest allowing the origin to be re selected
Reload Shape : returns to preview screen allowing the shape to be rotated etc & re nested.
Exit : clears shape memory and returns to main menu
Operation
If the plate is against a datum and the torch is correctly positioned, simply press the Test / Cut button to select cut mode, this will then go red indicating cut mode is selected.
Press Start, the machine will traverse to first pierce point and begin the cutting process. As the machine moves round the shape the cut path will go red.
When a part has been cut the pierce point will show as an orange dot as below.
Once the nest has been cut the end of cut screen will be displayed, the following choices can be selected:
Return to origin : select this to return to the origin of the part, usually used after the shape has been run in test mode, prior to selecting cut mode.
Jog off job : displays a jog panel allowing the cutter to be moved a set distance away from the job so it can be picked up.
Repeat : this displays a jog panel with four direction arrows indicating a repeat direction. The extents of the shape are measured and the correct repeat traverse distance is calculated and applied when a button is pressed.
Exit : this returns to the main menu screen and clears the shape memory.
If the nest is a very close fit to the plate it may be necessary to carry out a test run for example a dry run without the cutting process on.
Position torch on the start point as normal, select Test using the Cut / Test button
Press Start
The machine will begin to move round the nest, the torch can be raised or lowered manually to help with alignment. In the example below if the nest is too far to the right press Stop.
Press the Jog button
Press the left direction button to move the torch back on to the plate.
Press Move Job to “reposition” the nest on the plate .
The other Jog functions will be covered in a later section.
Press Start to continue round the nest.
To speed up the process it is possible to skip through pierces. To do this press Stop followed by the Fwd / Rev button
The following Screen will appear
Press and hold the Advance button.
The cursor will initially move slowly through the pierce points then after 5 seconds increase speed.
When the required pierce is reached release the button, if the cursor overshoots the required pierce, briefly press the advance or reverse button until the correct point is reached.
Press the Jump to Pierce button the machine will now move to the selected pierce point.
Press Start, the machine will then continue around the shape.
Alternativley, pressing Enter pierce will display a numeric key pad allowing the pierce number to be input directly. Or
Press on the screen to select the part required, the yellow dot represents the first pierce point of each shape.
If any further positional adjustments are required follow the Jog / move Job procedure as described earlier.
Once the nest is positioned correctly press Stop
Press the To Pierce button - the machine will move to its last pierce point
The To Origin Button will now appear instead of the To Pierce button
Press this and the machine will return to its origin (which will now be offset by the Jog / Move Job operation)
To Cut the shape press the Test / Cut Button and press Start
Other Features of the cut screen:
Back Up is not often used in plasma cutting (unless the plasma does not have an arc sensing unit)
The speed can be adjusted at any time to take in to account the plate condition etc.
Nest view / Zoom View Allows operator to zoom in on the cursor.
Press to return to Nest view
What to do if :
The plasma stops cutting part way round a shape.
Most plasma systems have an arc on sense circuit so the machine will stop automatically shortly after the arc extinguished. In this state the head will have risen up.
Clear any debris etc that may have caused the arc to go out.
Position the torch close to the plate using the raise/ lower buttons.
Press and hold the reverse button, the machine will reverse round the shape, release the button just after the point at which the arc extinguished.
Note do not position the torch over an existing cut path as the arc needs metal beneath it to strike.
If the machine moves too far use the advance button to position it correctly
Raise the torch.
Press the Start Button the machine will continue cutting.
A stitch is required in the job.
Some times a stitch ( an uncut area on the nest ) is required to hold a part in the plate to prevent movement or ease unloading.
When the required point is reached press Stop.
Press and hold the advance button until the machine moves the required stitch distance.
Press Start the machine will continue cutting.
The Consumables blow part way round a plate
The machine should stop automatically, if it does not press stop.
Select Jog
Use the Jog buttons to move the machine to a position where the consumables can be changed.
Exchange the consumables.
Press back to path.
The machine will now move back to its original position.
Once there press Start to continue cutting. ( It may be necessary to use the Advance / Reversebuttons to pick up at the correct point)
Under no circumstances use the Cut back to Path feature as this will damage the Plate, this feature is used when gas cutting or if the plate being cut is too thick to pierce as it allows n edge start to be carried out.
I need to cut a part out of sequence.
During the cutting process, wait until the present shape is finished.
Press Stop.
Press the Fwd / Rev button as described in the previous section to select the required part(remember the inner components of the parts are cut first).
Once the correct pierce is selected press Jump to pierce.
When the machine gets to position simply press Start.
The cutting sequence will begin again.
Once the part is cut you have the option to continue cutting to the end of the nest or returning to the point where you originally broke off cutting. Which ever option is chosen use the Fwd/Rev button again and jump to the required pierce, press Start and continue cutting.
Arc Voltage height sensing.
If the Controller is fitted with a Techserv Height Sensing Head the following controls will be available.
AVC on/off
Initial Height sense on/off
Manual head/raise lower
Arc Voltage increase/decrease
Set Arc Volts
Actual Arc Volts(only displays a value when cutting)
Status LEDs
The height sense uses two integrated systems:
Initial Height Sense IHS - when the cutting sequence is initiated the torch will drive down and touch the plate. This sends a signal back to the controller which then retracts the torch to the pierce height from the setup data.
Arc Voltage height sense Control AVC - This system measures the voltage created between the torch and the plate. The larger the voltage the greater the distance above the plate.
The system will start the arc at the pierce height as set by the IHS - once the plasma arc strikes an arc on signal is sent from the plasma, when the controller receives this it holds position for the preset pierce time, then commences motion. The torch will then drop to the cutting height.
When the machine reaches cutting speed the AVC will turn on and adjust the torch height to maintain the arc voltage.
As the machine slows to go round a corner the AVC will be turned off to prevent the torch diving in to the plate.
The machine will cut with either of the functions disabled – but the operator will have to adjust the torch position manually using the Raise Lower buttons.
Running in this mode for any length of time is not recommended.
Changing the AVC cutting height.
The Set voltage displayed is derived from the setup data, if it is necessary to adjust this value, press the +/- buttons to increase or decrease the set voltage when the machine is cutting and AVC is enabled
The actual voltage displayed will closely follow the set voltage.
Factors affecting the arc voltage are:
Cutting speed - if for some reason the speed is reduced the plasma will burn more material away, this increases the arc voltage causing the torch to run closer to or crash in to the plate.
If the speed is too fast the plasma will not penetrate the plate.
Material Type / Quality - different materials require varying arc voltages, ensure the correct material is selected during setup.
Rust and scale on the plate can effect the height sensing causing inconsistent operation.
Current - Ensure the plasma pack is set to the correct current value as defined during set up.
Consumable Wear - a badly worn consumable will cause the torch to cut closer to the plate, this is not normally an issue if consumables are changed at a sensible time.
NOTE: When adjusting the arc voltage settings it is recommended to carry out the changes in 1 volt steps.
Additional Information:
Quick Stop
The Precision Height Sense head is fitted with a breakaway device. This is designed to prevent torch damage caused by catching on tipped components during cutting or traversing. If activated the machine will stop movement and turn off the cutting process. A Limit Hit warning will appear on the cut control panel.
Cutting with Gas
Most of the main controls are the same as for gas as previously described for plasma.
If the machine has the optional automatic gas system fitted, it will automatically control the High and Low preheating oxygen pressure. Along with the cutting pierce ramp and cutting oxygen pressure.
On a gas only machine the above table will appear by default however on a combined Gas / Plasma machine the plasma screen appears first. Press the plasma / gas select field to toggle between the two processes.
As with the plasma process select the required plate thickness.
The thickness will be highlighted on the screen.
Cutting speed, preheat etc will be adjusted to automatically.
The Nest and Plate Align function work in the same manner as described in the plasma section.
If no changes are required press next to move to the origin screen.
Gas process data
To enter new data or edit existing press Save Data.
Turn on selected process
To adjust a pressure press Gas on and light torch and select at least 1 torch on the head select buttons.
To adjust a pressure ie High preheat oxygen Select oxy hi in the process set up pane .( The current pressure in bar and psi will be displayed).
Press the up/ down buttons to adjust the pressure.
To see the actual effect the adjustments are having press High preheat in the Test Gases Pane.
The pressure can be further adjusted, when desired results have been achieved press the gases off button.
Other variable settings are;
Cutting Speed
Kerf- allowance for thickness of cutting flame.
Preheat- Time in seconds machine turns on high preheat ( to speed up pierce time ) before turning on the cut.
Pierce Delay - Time in seconds the machine takes to accelerate to cutting speed whilst ramping cut pressure from low to high.
Nozzle size.
When all adjustments have been made press Save Settings.
The review screen will then appear.
If values are correct press save settings, this will return to the adjustment screen from there press next.
The Setup screen will reappear.
Press Next to move to the Origin Screen.
Select the required origin as per the plasma section.
To carry out a gas cut.
Position the torches on plate.
Select the torches required for cutting using the individual cut buttons.
Press Gas On button and light gases (adjust trim valves on torches if necessary).
Select Cut using the Test / Cut Button.
Press start.
The machine will move to the pierce point turn on the high pre heat, wait for the time defined in the set up screen, then turn on the cut and move off round the shape.
This process will continue until all parts are cut.
Press Exit to return to the Main Screen.
The fwd / rev, jog and view functions all work as described in the Plasma section.
The other functions will be described in the following section.
What to do if the cut comes on but does not pierce the plate.
The plate was not hot enough when the cut turned on.
Press Stop.
Press To Pierce - the machine will move back to the pierce point.
Press Start - the machine will restart its preheating cycle.
The same thing happens at the next pierce.
The preheat time is too short.
Whilst the machine is in the high preheat cycle press Hi preheat button. This will hold the preheat cycle on.
When the plate is hot enough press Hi Preheat button again - this will begin the cutting process.
The machine will then “remember” the new time for all following preheat cycles in the nest.
One of the torches blows out part way round a cut.
Press and hold the Backup button - the machine will slowly reverse round the cut path, when the torch reaches the position it blew out release the button.
The machine will then carry out a normal preheat/cut cycle and set off along the cut path.
The main difficulty arises when trying to pick up the cutting paths of the other torches. As the torches approach uncut metal press the Creep Speed Button this will reduce the cutting speed (to a creep) when the cuts re establish in the fresh metal press Creep Speed again -the machine will return to normal cut speed.
Jog Options
Pressing More jogs will cycle though the additional jog screens.
The relative jump screen is shown.
Tap the number fields and enter a relative distance to travel.
Pressing the do relative jog button will move the distances as input.
To move to a Table position press one of the Table positions.
Tip:
Pressing the numeric display on the jog screen will cause the display to zero, making relative moves easier to measure.
Manual Cut
Manual Cut - Plasma
This is useful for cutting Scrap and strip cutting
The settings on the screen will default to the last values to be cut.
If different settings are required, press set up and follow the procedure described in the cutting with plasma section.
Use the jog buttons to position the torch to the start position.
Press Cut - the machine will begin a cut cycle, immediately press the desired direction button.
When the plasma arcs up it will cut in the desired direction until either Stop is pressed or it runs out of material.
All arc voltage functions are the same as previously described.
Press Exit to return to the Main screen
Manual Cutting- Gas
Again the screen will default to the last setting being cut.
Press Gas on - light the torches.
Select heads as required.
Position torches on plate using the Jog buttons.
Press Cut, the machine will start a preheat / cut cycle.
Select the desired cut direction.
When the Preheat cycle finishes the machine will move in the desired direction until the stop button is pressed.
When finished turn gases off.
Press exit to return to main screen
Diagnostics
The following screen is accessed by pressing in the bottom left corner of the main start screen.
This screen displays the state of the input and outputs can be selected by pressing the relevant buttons.
Additional diagnostic screens can be selected by pressing the buttons on the top right of the screen.
Configuration
The machine configuration screen is accessed via a password. There are a number of settings selected via the tab buttons as shown.
Detailed configuration data.
1)Traverse speed
maximum speed of the machine in mm/min. If this parameter is set too high the machine will lurch on rapid traverse moves.
2)Backup speed
Speed in mm/min when backup, forward or reverse buttons are pressed. Typically 400mm/min on gas and 2000mm/min on plasma.
3)Min rad speed.
Linked with min rad mm and max rad mm. Fractional speed of a radius of min rad mm.
IE. value of 1 = full speed, 0.5 = half speed and 0 = no speed (at this speed the machine will not move at all) . Above the max rad mm value no slow down is performed. Between the max rad mm setting and min rad setting the drive speed is reduced on a linear basis between 1(full speed) and the min rad speed value. Below the min rad mm setting the arc is cut at the min rad speed.
4) min rad mm
Full slowdown is applied to the minimum radius
5)Max rad mm
slowdown is applied from this radius and smaller on a linear basis
6)Min slow angle
No slow down below this angle of direction change.
7)Max slow angle
Machine stops on the corner at a this angle or above
8)Min corner speed.
Minimum fractional speed at max slow angle. Linked with min slow angle, max slow angle and creep angle parameter on page 2. Fractional speed of an angle.
IE. value of 1 = full speed, 0.5 = half speed and 0 = no speed (at this speed the machine will not move at all) . Below the min slow angle value no slow down is performed. Between the min slow angle setting and the creep angle setting the drive speed is reduced on a linear basis between 1(full speed) and the min corner speed speed value. Between the creep angle setting and the max slow angle setting the angle is reduced on a linear basis between the min corner speed and a stop. Above the max slow angle the machine stops as the corner is performed. See also lookahead mode on page 2. If this parameter is set to a 1 i.e. ON - then the motion system will look several moves ahead, this helps the velocity profiler calculate the accel/decel around small rads (kerf fillet rads), ideally set to on when cutting with plasma.
9)Corner slow % height sense disable.
Percentage of drive speed at which the corner height sense is turned on. 100% = lots of corner height sense disable (height sense will not react). 50% = hardly any corner height sense disable (height sense will dive on corners). 90% typical.
10)Calibration X
Theoretical distance traveled ( ie display value) divided by actual distance traveled (measured distance) multiplied by axis calibration. Enter this number in the relevant box above and restart controller. Note the value obtained from the calculation should not be much different from the original number possibly just a few decimal places.
The autocalibrate function will perform this automatically.
11)Calibration Y
Theoretical distance traveled ( ie display value) divided by actual distance traveled (measured distance) multiplied by axis calibration. Enter this number in the relevant box above and restart controller. Note the value obtained from the calculation should not be much different from the original number possibly just a few decimal places.
The autocalibrate function will perform this automatically.
12)Corner height sense invert
0 = no invert. 1= invert height sense disable output
13)Proportional gain
Sets the proportional gain on the nextmove controller. Independent of the gain of the drive amplifier.
14)Integral gain
Sets the Integral gain on the nextmove controller. Independent of the gain of the drive amplifier.
15)Vff axis 1
Sets the axis 1 Velocity feed forwards parameter on the nextmove controller. Independent of the Vff of the drive amplifier. This parameter acts as a damper, typical value 25.
16)Vff axis 0
Sets the axis 0Velocity feed forwards parameter on the nextmove controller. Independent of the Vff of the drive amplifier. This parameter acts as a damper, typical value 25.
17)Max travel X
Maximum travel distance of the machine in the X axis mm
18)Max travel Y
Maximum travel distance of the machine in the Y axis mm
19)Table 1 X
Table positions in the bed relative to the home position.
20)Table 1 Y
Table positions in the bed relative to the home position.
21)Table 2 X
Table positions in the bed relative to the home position.
22)Table 2 Y
Table positions in the bed relative to the home position.
23)park position X
park position the machine will move to after homing (not yet implemented).
24)park position Y
park position the machine will move to after homing (not yet implemented).
25)Number of gas heads
1 to 8 gas heads - displayed on the left side of the display and individual cut solenoids output from the controller with proportional control of preheat and cut oxygen gas
-1 = no gas heads displayed and solenoid control of all gases.
26)Default plasma
0 = defaults to gas machine, any non zero value = defaults to plasma machine and selects plasma type.
0 = gas
1 = proline 275 amp range
2 = pmax 1650
3 = pmax 1250
4 = pmax 1000
5 = proline 200 amp range
6 = HSD 130
7 = Pac 500
8 = Ultra-cut 300amp
9 = Ultra-cut 100amp
10 = Cutmaster range
11 = Cutmaster A10
12 = HPR
13 = Fine focus 600
14 = HPR130XD
15 = Cutmaster A120
16 = Powermax 45
17 = Autocut
18 = Powermax 105
19 = Kaliburn 400
20 = Dagger 100
21 = Maxpro 200
22 = PowerMax 125
23 = PA S45 Kjellywerbleurble
24 = Cebora CP251
25 = PowerMax 45 XP
27)3 axis drive
0 = two axis drive system
1 = three axis drive system with Y axis slaved
2 = three axis drive system with X axis slaved
28)Machine handing RHC (1)
0 = left hand cut
1 = right hand cut
29)Buffer size
Move buffer size typically 40, maximum of 100 moves. Make this parameter larger if shapes with a large number of small blocks are cut.
30)Home direction X + (1)
Home search direction
0 = - direction (left)
1 = + direction (right)
31)Home direction Y + (1)
Home search direction
0 = - direction (backwards)
1 = + direction (forwards)
32)Rotate on import essi 0-4
Rotates a loaded essi shape before it is displayed
0 = 90 degrees
1 = 180 degrees
2 = 270 degrees
3 = no rotation
33)Rotate on import WADR 0-4
Rotates a loaded word address shape before it is displayed
0 = no rotation
1 = 90 degrees
2 = 180 degrees
3 = 270 degrees
34)Accel rate
Acceleration rate in
35)Decel rate
Deceleration rate in mm/s/s
36)Drive mode
Sets the operating mode of the nextmove controller
1 = servo mode
2 = stepper mode
5 = virtual mode ie no movement from the drive motors
37)Limit 1 = no
Limit switch input sense select
0= normally closed limits
1 = normally open limits
38)Home speed
Speed of home switch search speed in mm/min
39)Home position X
When home routine is finished the machine position is set to this value in mm
40)Home position Y
When home routine is finished the machine position is set to this value in mm
41)Square offset
The offset between the main and slave carriage switch points when the machine is square
42)Maximum skew.
The maximum amount the machine can be out of square, taking into account the square offset. If this value is exceeded during a home routine then the routine will stop and a skew error is displayed. The fault is remedied by returning to the main menu and pushing the slave side to correct the error. The home routing can then be restarted. Normally 25mm but flexible machine can have a higher value if required.
43)Cad traverse
0 = no change
1 = start and end traverse moves are stripped from downloaded programmes. This action allows the user to specify the plate setup point rather than the cad data.
44)Estop 1 = no
Emergency stop switch input sense select
0= normally closed emergency stop
1 = normally open emergency stop
45)Phase search on start 1 = T
0= no change
1 = on start up the 'please wait phase search' screen is shown. This is used when an AC motor is not equipped with hall sensors and the drive system has to perform a phase search to identify the drive position.
46)Use camera
0 = no camera on jog screen
1 = not implemented
2 = loads USB camera drivers and displays on jog screen
47)Import ABS = T
Essi file import
0 = relative data
1 = Absolute data
48)WA no cut on off
0 = import a standard word address programme with cut on/off commands
1 = import a non standard word address programme with no cut on/off commands ie assume G0 = cut off.
49)Jog lock on = T
0 = do nothing
1 = Display the jog latch button on the jog screen when the machine has not carried out a home routine.
50)Timeout (s)
Time in seconds that the machine will wait at the menu screen before returning to the main screen to switch off the drives.
51)Do kerf = T
0 = no kerf offset routine performed
1 = kerf offset routine performed on standard shapes and downloaded shapes if kerf downloaded shapes is selected (1)
2 = NCTC kerf on all shapes if kerf downloaded shapes is selected (1)
3 = BBS kerf on standard shapes - NCTC kerf on downloaded shapes
52)Plasma off delay
Time dwell in seconds before the machine will move after the arc has been turned off
53)Following error fatal
Position error in mm that the machine can travel before the following error activated and the motion stopped.
54)Use dongle
0 = no dongle protection
1 = dongle protection activated
55)Small arc speed up factor
no longer used
56)Height sense type
0 = no hs
1 = simple avc / ihs
2 = blue marlin plate riding roller
3 = blue marlin HTA stepper
4 = Hi Def height sense
5 = Hi Def height sense with following error plate detect
6 = simple height sense with touch down switch and HTA
57)x axis rev
selects direction of x axis drive and encoder sense
0 = no change ( stepper = no change )
1 = encoder reversed ( stepper = reversed )
2 = drive reversed
3 = encoder and drive reversed
58)y axis rev
selects direction of y axis drive and encoder sense
0 = no change ( stepper = no change )
1 = encoder reversed ( stepper = reversed )
2 = drive reversed
3 = encoder and drive reversed
59)Kerf download shapes
0 = no kerf offset on downloaded shapes
1 = kerf offset downloaded shapes if the do kerf parameter is set to 1
60)Bleed off time
Gas cutting bleed off time in 10 millisecond units ie 200 = 2 seconds (strange)
Page 2
61)Head rl speed
Sets raise lower speed of simple height sense head, no units as this value is hardware dependent typical value 60
62)AVC gain
Sets the gain of the AVC loop hardware dependent typical value 3
63)IHS raise calib
Sets the calibration of the initial height sense raise speed, height is set using a time delay
64)AVC calibrate
Converts arc voltage input to volts for display and height calculations.
65)Plate roller head down delay
Time in milliseconds to allow the plate riding roller head to drop before the plasma is turned on.
66)Hi Def height sense (Hold To Analouge function) HTA kprop
Height sense proportional gain, a negative value changes the hold direction must be used with the damping factor
67)HTA damping
Height sense damping factor
68)HTA kint
Height sense integral gain factor
69)HTA filter
Height sense filter
70)Latch kerf command
For use when the input programme has only one initial kerf command any further kerf commands are implied
71)Use joystick
Enables USB joystick function
1 to 10 = joystick selected and channel number
-1 = numpad
72)Fume bed (See end for Canbus setup data)
0 = no fume bed attached
1 = fume bed attached USB control
2 = fume bed attached Can Bus set node on bed setup screen
3 = Small fume bed uses output 6 for rear section
4 = Escco fume bed used with Phidget Relay interface type 1017. Phidget tray application should be installed for this to work.
73)Ignore arc off for(s)
set to 1 second to ignore the arc off signal received when cutting small circles with a lead out and the arc is lost
74)5 volt gas signals
rescales the AO signals for use with 5 volt valves ( normally 10 v )
75)external inhibit
external inhibit on DI7. When set to 0 the input is ignored, 1 the input is normally low, 2 for normally high, 3 the input is normally low and the drives are disabled, 4 for normally high and the drives are disabled
76)Idle precision (0.2)
Increasing the idle precision increases the window in which a drive is considered to be Idle, default is 0.2mm, reqired when motor mount encoders are not used on high mass systems. this parameter needs increasing if the 'return to pierce' function takes a long time to complete. (mm)
77)no enc prescale
Motor mounted encoders require a prescale factor as the pulse copunt is very high causing the counters to overrun. Machine mounted encoders however have a much lower pulse count so the prescale is not required. The default value is 'no enc prescale' set to 4321 to turn prescale off ( the value of 4321 is chosen as it is unlikely to be in this field accidentally)
78)Aux X P Gain
Used in conjunction with the above parameter, this setting allows the PGain of the axis to be set independantly, used when the axis are of different mass and dynamics.
79)waterjet=1
Waterjet extentions enabled
80)Partial raise height
Sets height sense raise height
81)HS follow error
Sets height sense following error, used when the torch touches the plate during the IHS cycle, if the torch stops short of the plate this value can be increased do not set too heigh as the torch will press the plate too hard typical value 0.2mm
82)Retract delay
Delay before torch retracts after cut. (ms)
83)IHS Delay
Not used, individual parameter set on process setup screen
Delay before IHS drops to cut height after cut is initiated, helps to clear slag pools on thicker material (seconds)
84)Prop gain
Proportional gain
85)Man speed
HTA height sense manual speed
86)IHS speed
IHS speed mm/min
87)Crossover height
Height above plate at which the head slows down, easured from torch park position, note the plate thickness is included in this value automatically
88)Height sense channel
Axis used by hi def height sense channel 2 on a 2 axis system or 3 on a 3 axis system
89)Height sense drive direction
selects direction of hi def height sense drive and encoder sense on the height sense
0 = no change ( stepper = no change )
1 = encoder reversed ( stepper = reversed )
2 = drive reversed
3 = encoder and drive reversed
90)HS encoder scale
Hi def encoder scale factor
91)HS K prop
92)HS Accel
93)HS Decel
94)HS lockout (mm)
Height sense is frozen if the cut is within xx mm of a cut off. Used to help prevent the head diving into the plate when reaching the end of the cut. Typical setting 5mm. Red indicator shows on the run screen and cursor turns purple when the lockout is activated. Set to zero to disable. When configured as a waterjet machine, lockout flags the end of a cut and initiates slow down routine.
95)AVC speed
96)HTA deadband
97)Creep angle
see min corner speed setting
98)Treat kerf fillet as line
set to 0
99)Lookahead mode
see min corner speed setting
set to 0 for gas
1 for plasma
100)Close loop for kerf
< 0 checks individual shape geometry for a closed loop, ie start and end point should be the same, if they are not, a correction is added. Note only works with a lead in and out.
0 = no change
1 and above applies granuality factor to kerf routine, increases the tolerance of the offset routine to inaccurate geometry (2)
101)Return to origin after cut
Only functions after the machine has been homed. Note the end of cut screen must be enabled for this feature to function.
0 = no change
1 = return to origin after cut
2 = return to home after cut
3 = return to table 1 after cut
4 = return to table 2 after cut
5 = return to table 3 after cut
6 = return to table 4 after cut
7 = return to park position after cut
102)Generic shape code
activates optional generic shapes
103)Priority
Sets programme priority within windows
5 = realtime
4 = high
3 = above normal
2 = below normal
104)Show man cut on run screen
0 = not shown
1 = shown
105)IO loop speed ms
Speed of the IO loop in ms, a slower PC may need a slower loop speed to prevent USB data clashes (screen hangs up) 30ms on a fast pc, 50ms on a slow pc
106)Cut on delay ms
Sets the amount of time the programme waits whilst setting the cut on logic. Not cut on delay or pierce delay
107)Default to cut on mode (1)
Sets run screen mode to cut rather than test
108)Remove centre origins (1)
Removes centre origins on run screen (reduces screen clutter)
109)Plasma off early decel factor
If set to zero no plasma off early function. If set to 1 then off early distance is calculated on cut speed, an allowance is made for the decelaration of the machine towards the end of the cut i.e. the plasma turns off later (closer towards the end of the cut) the current time value can be used to trim the off early function to ensure cuts finish or to reduce the amount of burn in.
If 2 is entered then the routine just calculates the early off distance on the last line rather then 1 which calculates the early off on the last 2 lines.
if a negative value is set then then this function acts as a slow down at the end of the cut to assist in finishing off the cut when a process with a large drag angle is used i.e. H17 cutting. The negative value representst the % feedrate to be used i.e. -20 = 20 % speed for the last x ms as selected by the current setting on this page.
If this value is set to 3 then the routine is simplified, the earlier current settings in ms are changed to mm. Typical setting of 3mm
110)Table 3 x
Table position
111)Table 3 y
Table position
112)Table 4 x
Table position
113)Table 4 y
Table position
114)scrap allowance on repeat
115)scrap allowance on origin
116)drive direction slave
selects direction ofslave drive and encoder sense on a 3 axis system
0 = no change ( stepper = no change )
1 = encoder reversed ( stepper = reversed )
2 = drive reversed
3 = encoder and drive reversed
117)close loop, repair arcs (1,1)
leave set to 0 as no longer used
118)Consumable monitor (0)
Display consumable monitor
119)Slow jog factor
Jog multiplier to give low jog speed. (0.05) smaller number gives slower speed
120)AVC source
selects which channel 0 or 1 to be used as the plasma arc voltage input source
when 0 is used channel 1 acts as the touch down input channel.
If channel 1 is specified the Labjack input 0 is used as the touch down input
If channel 3 is specified, then channel 0 is used as the HTA input and the Labjack input 0 is used as the touch down input.
121)Use software limits
0 = not active
1 = Do not use type 1, use type 2
on, machine will stop when drive is not between the values below - only when the machine has been homed
2 = similar to 1 but implemented in software to prevent drives from drifting, also has aux x drive support
122)- x limit
software limit stops when less than or equal to this value
123)+x limit
software limit stops when greater or equal to this value
124)- y limit
software limit stops when less than or equal to this value
125)+y limit
software limit stops when greater or equal to this value
126)Canbus gas node
selects which node the canbus will use for the canbus AO signals
127)essi scale factor
Used when esi data is not in the usual 10mm format
128)Force homing
0 = not active
1 = machine must be homed before a shape can be loaded
2 = Z axis must be homed before a shape can be loaded
129)fan on time (s)
0 = no action
non zero = automatic fan time. Fan output turns on when plasma it on and remains on for this time in seconds
130)look for double cut
This parameter freezes the plasma height sense when a cut line passes close to a pre cut line. To prevent inadvertent operation the double cut check is active over the last xx mm of cut line as specified in this parameter (100mm is a good start value) The checking distance is shown on the display by two blue dots, one following just behind the cursor and one xx distance behind ( a function of the window size parameter.
131)Window size
This specifies the distance within which a cut is classed as a double cut and the height sense is frozen (3mm)
132)Corner slow mm
133)marker on code
set to match essi marker on code used or word address code without the leading M (automatically inserted)
134)marker off code
set to match essi marker off code used or word address code without the leading M (automatically inserted)
135)x marker offset
x axis offset between cutting torch and marker in mm
136)y marker offset
y axis offset between cutting torch and marker in mm
137)marker type
0 = no marker
1 = drill
2 = plasma marker
3 = pneumatic pen
4 = magnetic drill
5 = hi def plasma marker
6 = Spot marker
7 = Powerma marker
138)marker speed
Travel speed in mm when marking not used with drill
139)marker down time
time in seconds for marker to drop to the plate
140)marker drill time
drill on time in seconds
with marker type 4 this should be set as a maximum time out as the drill will lift the drive inhibit signal once the drill cycle is complete and the marker cycle will finish
141)inhibit homing till drill is up
0 = no action
1 = marker up input has to be on before machine homing is permitted
142)hide angle jogs
0 = no change
1 = hide the jog buttons located at the 45 degree positions
143)hide history
0 = show history
1 = hide history on run screen (default)
144)Draw arcs as lines = T
0 = draws arcs as arcs, can lead to gappy plots
1 = draws arcs as lines, cleans up plot screens but uses more processing time to regen the plot
145)cyb simplify
Factor 0 to5 used to combine small lines as used in Cybermation machines to longer lines while maintaining shape geometry. Small lines can cause buffer underrun ( jerky motion )
146)Heartbeat Popular tv series ( never watched it so can't comment )
147)DXF simplify
This routine scans a dxf file and identifies lines less then 3 mm long and with an angle change of less than 5 degrees, these lines usually form arcs etc. The lines are then removed to simplify the file. The parameter sets the maximum number of lines that can be removed. For example setting the parameter to 10 would remove 9 lines and leave the 10th. Typical value 10, when set to zero the routine is skipped.
148)Special import filter
For strange machine dialects
1 = Farley fabricator
2 = Sigma nest
3 = Techsoft
4 = Igems
5 = Messer
6 = SheetCam
7 = Stripped word address
8 = CADlink
9 = Sigmanest waterjet
10 =Word address special ABS with relative arcs
11 = Sigmanest ANCA
12 = Sigmanest WA with line numbers
13 = Pronest Word Address
14 = Sigma Word Address with marking codes
15 = Nestmaster Word Address with kerf commands
16 = Shapecut ESSI, kerf command after cut
17 = Word address Vulcan ( no cuts, G1 = traverse and no arcs
18 = G code special
149)2nd plasma type
For machines fitted with 2 different plasma packs, specifies the plasma type for plasma 2 same format as default plasma
150)2nd avc calibrate
as above the 2nd plasma pack requires a seperate avc calibration value, or it s stepper plasma heads are fitted, acts as avc calibrate for second head, defaults to head 1 avc calibrate if left blank
151)Use plasma select input 1 = T 2 = inv
For twin plasma systems allows the switching of the plasma types to ve via a front panel switch
0 = dont use switch
1 = use switch
2 = use switch but invert input
152)Pre start plasma
0 = off
1 = on
When selected starts the plasma as soon as IHS routine is started. Hold signal is then issued and released when plasma has started, reducing cycle time
153)Thick pierce lift mm
When the plasma pierce delay is set to a negative value the THC will raise this amount above the plate and start motion, this is to prolong consumable life and to avoid cutting through the splatter
154)Lead in slow factor
Typical 40(%)
This factor reduces speed when cutting a lead in line, useful when cutting reduced speed circles ( bolt holes) works for a maximum lead in of 10mm the resumes normal speed.
155)Home Z switch fitted
Set when a plasma height sense is fitted but with no external Z top limit, ie limit is built into motor. Outputs Z raise signal for 5 seconds.
156)Invert plate sense.
Inverts the sense of a plate detect switch.
169)Knife on code
170)Knife off code.
171)HS on code
Specifies WA code to enable auto height sense
172)HS off code
Specifies WA code to freeze auto height sense
173)Mid programme stop code
Specifies WA code to issue a STOP command during a programme. Used when the programme requires a manual change, such as turning a gas head off etc.
174)Head select out =1
outputs gas head select signal when head is selected rather than when head is selected and cut is on, used for selecting height sense etc.
175)Multi plasma heads
Number of plasma heads fitted on a multi head machine
176)Multi plasma mode
mode 1 start as soon as 1 plasma fires
mode 2 start as soon as all plasmas have fired or wait till time out and stop
mode 3 start as soon as all plasmas have fired or wait till time out and start
177)Multi plasma time out (ms)
Timer value used above in milliseconds
178) Invert height sense limits
1 = both limits inverted
2 = only upper limit inverted
3 = only lower limit inverted
inverts height sense raise/lower limits, aids noise supression
179)nesting option code
enables nesting option
180) demo mode
Controller works in demo mode, no external device required
Page 4
181)Wiggle pierce dia
set the diameter or the circle when a wiggle pierce is performed , 1mm typical
182)Reduced cut accel
Allows a slower accel/ decel rate to be used when cutting, does not affeect the jog or manual cut accel rates. Value is fractional .1 to 1 ( do not use 0 as the machine will error and not move )
183)Aux head channel
Axis channel to be used by the aux head (usually 3)
184)Aux axis rev
selects direction of x axis drive and encoder sense
0 = no change
1 = encoder reversed
2 = drive reversed
3 = encoder and drive reversed
185)Aux home direction
Home search direction
0 = - direction (left)
1 = + direction (right)
186)Aux home position
Position assigned to aux axis when home position is found
187)Aux min spacing
Minimum spacing permitted between main head and aux head.
188) WJ Stepper heads
Outputs stepper signals to control raise / lower heads on a water jet and gas machines.
189)Master cut out
Outputs a master cut out signal on OP11
190)AVC thick pierce (s)
Not implemented
191) simple AVC limit
Limits the maximum AVC output used on simple height sense, required to prevent height sense diving into plate. Typical value 25 i.e. 2.5 volts (drive card uses +/- 5v)
192)Simple HS speed % NOT used
used with Simple HS overtravel parameter to speed up the IHS limit switch overtravel, defaulted to 30%
193)Simple HS overtravel NOT used
When using the simple HS IHS ( ie touch down on a linear slide or similar ) the overtravel parameter is set to equal the amout of movement from the switch remaking to the torch leaving the plate. Used if there is a lot of lost motion in the system or overtravel before the switch operates. Units mm
194)Single prop valve
Combines the analouge value of both preheat and cut oxy, to allow the use of a single proportional valve, must be used with an additional solenoid and non return valve.
195)Use Labjack type
Forces the Labjack outputs to be used regardless of machine configuration.
Set to 1 for Labjack U12
Set to 2 for Labjack U3 with LJ dac tick module
Set to -1 to not call labjack ( for test only )
196)More slow lead in
Uses an advanced slow down programme to detect if a small diaameter is being cut, if so the lead in line and any small arcs and lines are cut at the slow arc speed. When used this function overrides the 'lead in slow factor' parameter
197)Do not limit jogs
Jog function uses machine software limits to set maximum jog travel, to reduce the risk of crashing the machine against the hard stops. Only set this bit if there are no values in the software limit fields
198)Do not display kerf
Allows for a faster redraw by only displaying the kerf offset line in blue and not the original geometry, used if large nests are causing the system to run slowly
199) Do not use origins = 1
Overrides the orign select buttons on the run screen when cutting downloaded nests, used if the nests are irregular in shape and fit to remenant plates
When set to 2 overrides the origin as above and traverses to absoloute sheet start position X and Y as defined on next column
200) e100 = 1
Set to 1 to use e100 controller, not yet implemented
201) Multi threading =1
Set to 1 to enable multithreading of the Nextmove ActiveX thread
202) Gas torch type
Selects gas cutting torch type.
0 = Harris
1 = Messer
203)0 to 10 bar output
Set to 1 to give 10 bar = 10 volt output
normally set to 0 to give 7 bar = 10 volt
204) Disable quickstart
When set to 1 quickstart plasma function is disabled.
205)remap +X limit
remaps the +X limit input, use 6 or 7 to map to input 6 or 7
206)remap x home limit
remaps the x home limit
207)remap IHS switch
remaps the IHS switch
208) Sheet start X
Defines X sheet start position in absolute coordinates
209) Sheet start Y
Defines Y sheet start position in absolute coordinates
210)Default thickness
Sets initial default value used on job setup screen
211)Default material
Sets initial default value used on job setup screen
0 = left hand button
1 = next button etc.
212)Default current
Sets initial default value used on job setup screen
0 = left hand button
1 = next button etc.
213)Short traverse no lift
Specifies maximum distance machine will move without lifting plasma head in mm
0 = always lift, typical value = 50
214)Split long lines mm
Breaks long lines into segments to reduce unwanted slowdown at end of line
set to 800mm ish
215) Essi split arcs
Splits circles in two arcs in ESSI programmes, used when +0+0+I+0+ type geometry causes issues
1 = on
216)Low cut feed %
Sets feedrate whilst low cutting pressure is ramping up, both gas and waterjet process.
217)Small inner min mm
Small holes ie inner squares slots etc. ( round holes use the settings in the special hole routine ) are slowed down by the small hole speed factor (below). This value sets the minimum size the speed is factored over. I.e.
Small inner max mm size = no slow factor
Small inner min mm size = full slow factor
Typical value 20mm
218)Small inner max mm
Small holes ie inner squares slots etc. ( round holes use the settings in the special hole routine ) are slowed down by the small hole speed factor (below). This value sets the maximum size the speed is factored over. I.e.
Small inner max mm size = no slow factor
Small inner min mm size = full slow factor
Typical value 60mm
219)Small hole speed factor 0-1
Small holes ie inner squares slots etc. ( round holes use the settings in the special hole routine ) are slowed down by the small hole speed factor. This factor sets the minimum speed the minimum size hole is cut at. The factor increases to 1 on a pro rata basis untill the Small inner max mm size is reached.
Typical value = 0.4
220)Laser offset X
Laser pointer offset from the cutting torch in mm
221)Laser offset Y
Laser pointer offset from the cutting torch in mm
222)Abrasive calibrate 1
Waterjet only. Abrasive feed unit 1, use this calibration factor to enable ( non zero value ) and calibrate the abrasive feed stepper motor to deliver g/min ( grammes per minute )
223)Abrasive calibrate 2
Waterjet only. Abrasive feed unit 2, use this calibration factor to enable ( non zero value ) and calibrate the abrasive feed stepper motor to deliver g/min ( grammes per minute )
224)Min arc slow down angle
Waterjet only. Minimum angle which the arc slow down routine will activate, default 30 degrees. I.e. any angle over 30 degrees will be cut at a speed defined by the min rad speed and associated radius settings
225)Plasma no arc on threshold
Used when the plasma pack does not give an arc transferred signal, CNC sees a voltage between 50v and this value as an arc transferred signal when the plasma set to on. Typical value 200v
226) X Kvelff
X axis velocity feed forward
typical value 200, reduces following error, dependent on axis mass etc.
227) Y Kvelff
Y axis velocity feed forward
typical value 200, reduces following error, dependent on axis mass etc.
228)Advanced hyper hole
0 = off
type 1 =Automatic
type 2 =Cmd Li A Lo
type 3 =Cmd Li A A Lo
type 4 =Cmd Li Li A A Lo
type 5 =Cmd Li Li A Lo Lo
type 10 = special for Acad lisp interface by 'Straight Lines'
type 11 = special 270 degree arcs used by days
type 12 = Lantek essi
select type to suit hole programme type
Cmd = command
Li = lead in
A = arc
Lo = lead out
229)Reconfigure IO
Enables the reconfigure IO screen
230)Colour
selects colour scheme
231)Advancd hole off param
Distance in mm at which the arc turns off, typical set to 2 for hi def plasma, and 0 for conventional
232)S Ramp
Selects trapezoidal or S ramp accel /decel type
0 = trapezoidal
1 = S ramp
If S ramp is used the Accel jerk and Decel jerk parameters are also used
233) Accel jerk
Sets the rate of change of acceleration during periods of acceleration, expressed in mms/second3
234)Decel jerk
Sets the rate of change of deceleration during periods of deceleration, expressed in mm/second3
235)Max Z travel
If the IHS is atempting to find the plate and heads down a hole, set this parameter to the lowest plate position to reduce the chance of the torch getting snapped off. Default 280mm
236)Re start plasma
Not yet implemented
237)Waterjet calib 0mm
Waterjet height sense calibration value, measure the AI value of the height sense potentiometer when the nozzle is touching the plate and enter that value here (typical 85)
238)Waterjet calib 10mm
Waterjet height sense calibration value, measure the AI value of the height sense potentiometer when the nozzle is 10mm above the plate and enter that value here (typical 65)
239)Plasma marker pulse ms
Length of time in miliseconds that the plasma pack is pulsed on, when marker type 6 is selected
240)Alternative slow down
Water jet only, Calculates the angle of each move and applies is factor to slow the machine in and out of the corner. This is a factor and is applied in two stages 4mm and 2 mm before the corner. 4mm is 0.5 x the factor. Typical value 0.3
241)Stepper head
2nd stepper height sense head T=1
242) Stepper head IHS
2nd stepper head IHS switch offset
243)Collision value
Set to non 0 to enable. This function activates the collision detection sensor. A larger value decreases the sensitivity, i.e. 0.5 would require a larger deflection to activate than 0.1
244) Slave enc scale
Sets the slave (axis 3) encoder scale, if set to aero ( default ) then the same scale is used as the main axis, only used if the gear ratio or encoder counts are different between the axis.
245) Use old dxf in
Uses the old seperate dxf2gcode exe rather than the integrated one.
Included for debuging and beta testing.
246)Stepper gas output
Sets proportional gas valve channel when using an ES stepper card, set to 1 or 2 representing chanel 0 or 1
247)Tile mode
Removes the outer profile of the shape and auto repeats the inner, used when cutting multiple parts form a jig eg cutting tiles. Set to 1 to activate.
248)Read NC1
Activates NC and NC1 import filter for Strucad/Tekla files
249)WJ cut off slow mm
Distance in mm to slow down before a cut off block.
250)Retain shape origin
setting this parameter to non zero retains the last parts origin.
251)Plasma corner speed
When cutting with plasma the system uses this corner speed to reduce ringing on less dynamically stable machines. The standard corner speed is used for gas cutting to reduce dwell on corners. If set to 0 the system defaults to the standard corner speed, typical value 0.01
252)Plasma quick cut
When set to non zero, this feature bypasses the preview and plasma setup screen, when used with the do not use origin and plate start functions, the system operates in a manner more typical of a duct cutting machine.
253)Hole to marker.
converts a hole of this radius to a marler on/off sequence (fixed at 1.5mm rad).
Must have no lead in or out, currrently only for sheetcam files
Create a text file here with the cnc code that should be replaced C:\data\marker substitute text.txt
254)Marker 6 delay.
Time in seconds the machine waits after marking to allow the plasma purge to stop, about 8 seconds with a powermax 1250.
255)WJ Press calib
Water Jet pressure calibration multiplier. This value converts the CNC pressure value ( in Bar ) to volts.
256)WJ Hi Press bleed
Water Jet Hi pressure bleed off time, activates at end of cut to dump high pressure and switches to low pressure. Time in seconds.
257)End of cut off = 1
End of cut screen, showing return to origin - repeat - jog away from job etc.
Default is set to on, set to a non zero value to disable.
258)Backlash X
X axis backlash compensation in mm
259)Backlash Y
Y axis backlash compensation in mm
260) Backlash interval
Time in ms over which the backlash is introduced, typical 1000 ms
261)Large arc threshold
If an arc is larger than this threshold value it is consiered to be a straight line and converted in the import routine.
Typical value 500000 ie 500 metres, set to 0 to disable
262) Hypertherm DCC
Set to non zero to enable Hypertherm Direct Current Control feature and HPR autogas control.
RS485 port must be configured to Com 3 via device manager for this feature to function. Also you must have a compatible plasma pack, a RS485 converter and NI VISA should be installed.
263)Home Y axis first
When set to 1, the Z axis home is found followed by the Y and X rather than X and Y
264)Swap Labjack output
When set to 1 swaps the labjack output channels from 0 to 1 and 1 to 0
265)Precision increment
Distance between measurements listed in the precision table typically 10 mm
266)Precision mode
Setting this parameter enables the use of a precision table.
0 = not loaded
1 = single table for both directions
2 = tables for each direction
The table is a 2d csv array located at C:\data\ precision table.txt
and represents the actual tool position at each increment i.e.
0.00,10.01,20.00,30.00,40.02,50.03,59.98 etc
The format is :-
x axis forward ( or both forward and reverse, if so leave out the last 2 or 3 lines )
y axis forward
yy axis forward ( not required for 2 axis systems )
the next are optional
x axis reverse
y axis rev
yy axis rev ( not required for2 axis systems )
267)Set Origin on Jog
Replaces move job button with a set origin button, when pressed this sets the origin to the current point and realoads the shape so the part will start fron the new origin point
268)Wiggle speed mm/min
Sets the wiggle speed when waterjet cutting. Defaut 200 mm/min
269)Variable origin
When set to 1 this parameter will use the origin of the shape if the bottom left screen origin is selected, or the shape extents if the other origins are selected. If the shape is rotated or mirrored then the extents are used in all cases.
270)Autoload file
When set to 1 the load file screen will attempt to load the next file in sequence, if there is no file then the file select screen will be displayed as normal. Cancel by pressing the autoload button.
271)Tube Mode
When set to >1 tube mode is activated and the tube starrt button appears on the start screen.
A value of 1 sets the cnc in curcumferential drive mode, 2 is stepper centre drive mode and 3 is servo centre drive mode.
272)Tube Calibration
Calibration factor for the tube axis curcumferential drive mode.
273)Tube backlash X
Tube axis backlash
274)Tube backlash Y
Y axis backlash when in tube mode
275)Tube backlash interval
Time in ms over which the backlash is introduced, typical 1000 ms
276)Tube max speed
Maximum traverse speed when in tube mode
277)X Kderiv
278)Y Kderiv
279)X Kaccel
280)Y Kderiv
281)Test run speed
Traverse speed in mm/min when set to high speed in test run. When set to 0 defaults to 3000
282)Accel jerk time
The time required to reach profiler ACCEL from zero, expressed in milliseconds
283)Decel jerk time
The time required to reach profiler DECCEL from zero, expressed in milliseconds
284)Anti bounce accel
When set, introduces an additional set of accel/decel parameters, only used in plasma mode.
This value is a factor so setting it to 0.5 will reduce the speed in the corner to 50%.
285)Techserv Kerf
When set to a non zero value the techserv kerf routine is used on downloaded shaped.
BBS kerf is still used on flexi shapes.
When set to 2 Techserv kerf is used on all shapes
286)Plasma 2 AVC calib
Calibration factor for second plasma head on multi head ( duplicate ) plasma systems, takes main calibration value if set to 0
287)Time till low Kprop (s)
This parameter times when the drives are idle and after x seconds sets the Kprop gain to 0.25 of its value. As soon as motion is attempted the Kprop resumes its original value. Set to zero to disable the function.
288)Stepper delay (us)
Delay in micro seconds between a change of step direction and the commensification of the pulse train. Range 0 to 4 microseconds.
289)Kerf arc tolerance
If the start and end radii of an arc vary by more than the % tolarance specified, then the arc will be split into straight lines and not recombined. Larg arcs at high speed may cause the machine to overrun the move buffer, causing the machine to stutter. If this occurs the ideally adjust the geometry of adjust the tolerance up.
290)Alt import code
0 = not used
1 = tap
2 = cnc
3 = mpx
4 = esi
5 = b3
6 = dxf
7 = nct
8 = awj
9 = tes
10 = cyb
11 = sav
12 = n
13 = N
14 = mpg
15 = lst
16 = mc3
17 = nc
18 = nc1
19 = cod
20 = tf
291)Alt import type
For strange machine dialects
1 = Farley fabricator
2 = Sigma nest
3 = Techsoft
4 = Igems
5 = Messer
6 = SheetCam
7 = Stripped word address
8 = CADlink
9 = Sigmanest waterjet
10 =Word address special ABS with relative arcs
292)Alt Superhole type
0 = off
type 1 =Automatic
type 2 =Cmd Li A Lo
type 3 =Cmd Li A A Lo
type 4 =Cmd Li Li A A Lo
type 5 =Cmd Li Li A Lo Lo
type 10 = special for Acad lisp interface by 'Straight Lines'
type 11 = special 270 degree arcs used by days
type 12 = Lantek essi
select type to suit hole programme type
Cmd = command
Li = lead in
A = arc
Lo = lead out
293)Kerf comp superhole
Compensation applied to superhole in addition to kerf com to allow for additional material removed due to reduced speed 0.2 mm
294) Kerf with leadouts
Set to 1 when cnc programme has leadouts so kerf corrects properly. Temporary function whilst automatic version is implemented
295) PlasmaCam
Set to 1 when used with PlasmaCam machiine , IE no head top limit fitter.
296) Kerf special
Used with 'Straight Lines' Autolisp routine
297) Tube calib centre mode
Calibration value for a centre driven chuck, should be set so that 360mm of travel equals one turn.
298) Enable input
Default is Din 11.
When set to 0 the input is ignored.
When set to 1 cutting is disabled when high
Set to 2 cutting is disabled when low
299) Waterjet deep decel
When set to 1 this function uses the min rad speed slowdown in addition to the waterjet slowdown factor.
Min rad speed.
Linked with min rad mm and max rad mm. Fractional speed of a radius of min rad mm.
IE. value of 1 = full speed, 0.5 = half speed and 0 = no speed (at this speed the machine will not move at all) . Above the max rad mm value no slow down is performed. Between the max rad mm setting and min rad setting the drive speed is reduced on a linear basis between 1(full speed) and the min rad speed value. Below the min rad mm setting the arc is cut at the min rad speed.
300)Flip kerf side
Set to 1 when kerf appears on wrong side.
301)HPR marker gas
set to 0 the HPR uses Nitrogen, set to 1 it uses Argon and air or nitrogen depending on the material type.
302)Default to High speed jog
303)Drive to point after homing
Only functions after the machine has been homed.
0 = no change
1 = Park at table 1
2 = Park at table 2
3 = Park at table 3
4 = Park at table 4
5 = Park at park position, as entered positions below
304)Make origin top left
Only used if Do not use origins is set to 1, default mode is bottom left origin,
when set to 1 this makes the origin top right,
2 = top left
3 = bottom right
4 = bottom left
5 = top middle
6 = bottom middle
7 = centre
305)Micro waterjet
Set to 1 for use with a micro waterjet and untilises a phidget card for the abrasive feed unit.
306)Set from job
Sets the diameter of the tube from the incomming data automatically
307)Powermax lead length
Sets the plasma to the correct pressure for the lead length fitted. Only used when the CNC sets the plasma current, i.e. DCC is set to on. Only valid with the Powermax 65, 85 and 105 plasma packs.
0 = 15.2m = 80 psi ( default )
1 = 7.6m = 75 psi
2 = 22.9m = 85 psi
308)Kerf squeeze
Minimum angle for the kerf squeeze factor to take effect.
If two lines meet at an ( outside ) angle above this value the routine truncates the lines and inserts a small line to prevent the kerf compensation line becoming too long, given a very large angle it would approach infinity.
Typical value 99 degrees, set higher if spurious lines appear.
309)Stop input
Enables a remote motion stop / start input.
0 = disabled
1 = enabled n.c.
2 = enabled n.o.
310)Alt marker offset X
311)Alt marker offset Y
312)Use alt marker
If multiple process machines are fitted wit a seperate marker then two sets of marker offsets are required.
Set to 0 to just use the standard marker offset
When set to 1 the standard marker offset is used for gas cutting and plasma uses the alternative marker offset.
313)Simple CAD
Enables the simple cad drawing tool when the code is entered.
314)Short traverse
Ignores traverse moves less than this length when cut one part feature is used. A short traverse usully indicates the use of a tab when waterjet cutting. If one part is selected the part will have to be tabbed manually.
315) Invert home switch
Set to 1 to invert the home switches
316)Sleep on exit
When set to 1 the pc will sleep rather than shut down on exit. Used when the pc will not restart after AC power loss
317)Language
Selects language
0 = English
1 = Dutch
Set to -number to reset to english
318)Remove kerf arcs
set to 1 to remove arcs less than or equal to the kerf radius before kerfing ( tes kerf only )
319)Trim Kerf ends
trims off the last line of each shape before kerfing if the line is less than this value long (mm)
320)Marker Z height
Head moves to this height when marker type 3 is used ( pneumatic pen ) plate thickness is taken into consideration.
321)Combi Machine
Set to 1 if the machine is a waterjet / plasma combination machine
322)Change proc code
This code sets the subsequent cutting process to the secondary selected process. The code +1 activates the primary process. Default 61 & 62
323)Multi pro offset X
Offset between plasma and waterjet torch on a combination machine, X axis
324)Multi pro offset Y
Offset between plasma and waterjet torch on a combination machine, X axis
325)Outboard gain factor
Use this factor to damp the outboard drive (YY). Acts as a factor so setting to 0.5 would half the gain. If set to zero the gain will use the same value as the Y axis
326)Kerf square point off
setting this value to non zero turns off the kerf square point calculation
327)Temporary autonest code
361)
Setting the Wago can bus module
Power off
Set all dip switches to off
Power on
set dip switch 3 to on (125kb) followed by dip switch 8 to on (save data)
Power off
Wait 10 seconds
Set dip swith to binary node value i.e. sw2 on = node 2. Do not use node 1 as this is the supervisory node (note switch 8 should now be off).
Power on
Wago is now set. Run light will be flashing anlong with Tx & Rx (waiting for data)
If you are still having difficulties it may be nesesary to power down the machine and bed completely as the Nextmove may require bus reset.
Enter machine configure screen
set fume bed to a 2
enter fume bed setup and set can bus node to a 2 ( or the node selected )
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.