Manufacturer



Table 15 A of AIS-007 (Revision 5)DETAILED TECHNICAL SPECIFICATIONS FORCONSTRUCTION EQUIPMENT VEHICLES FOR COMPLIANCE TO CEV STAGE IV/V 1.0Details of Manufacturer1.1Manufacturer's name and address1.2Telephone No.1.3Fax No.1.4E-mail ID1.5Contact person2.0Vehicle Data2.1Basic model2.2Variant(s)2.3Type/Designation as per IS/ISO 6165/CMVR2.4Engine No.2.5Chassis No/PIN Number as per AIS 1362.6Publications available (Owner's manual, service manual, spare parts list) as per IS/ISO:6750:20052.7Color/ color code (As defined in Parivahan)3.0Performance 3.1Max. speed (kmph)3.1.1Forward (kmph)3.1.2Reverse (kmph)3.2Stopping distance (m) as per AIS 143 (Rubber wheeled M/c) & IS/ISO 10265 (Rubber tracked crawlers ) (From initial speed kmph)3.2.1Service brake 3.2.2Secondary brake 3.3Parking brake performance as per AIS 143 3.4Climbing performance (start & stop)3.5Min. turning circle diameter (m) as per IS/ISO 7457:1997 and IS:5500 Part 1&24.0Weights4.1Vehicle kerb weight (kg)4.1.1Front axle (FAW1, FAW2 etc.)4.1.2Rear axle (RAW1, RAW2 etc.)4.1.3Total5.0Dimensions IS/ISO: 9248:1992, IS:11114-2:2006 / ISO 6746-1: 2003 & IS: 11114-2006 / ISO 6746-2:20035.1Overall length (m)5.2Overall width (m)5.3Overall height (m)5.4Wheel base (m)5.5Tread (m)5.5.1Front wheel5.5.2Rear wheel5.6Min. road clearance (m)5.7Road clearance from floor (m)5.8Body overhang (m)5.8.1Front end5.8.2Rear end5.9Gravity height (m)5.10Max. stable inclination angle5.10.1Left5.10.2Right5.11Riding capacityNote : The essential characteristics of the Parent engine and the Engines falling in the same family are as given in the enclosed Annexure - 1. Clause 6.0 to Clause 27.0 are related to the characteristics of the parent engine. Clause A 6.0 to A 27.0 are related to the characteristics of every engine that falls within the same family. This may be filled separately for each engine.6.0 Engine (Parent)6.1Type (NA/TC/TCIC, DI/IDI)6.2Manufacturer's name & Address of the Manufacturing Plant.6.3Working principle (four / two stroke)6.4Model name and identification6.5Type of fuel used6.6No.& Layout of cylinders & firing order6.7Swept volume (cc)6.8Bore (mm)6.9Stroke (mm)6.10Compression ratio (specify tolerance)6.11Engine performance (declared by the manufacturer)6.11.1Max. Gross power of engine on bench kW (Specify standard and tolerance)6.11.2Maximum Gross torque on bench Nm @ rpm6.11.3Engine RPM at max. Power (specify tolerance)Note: In case of diesel engines the max. power and max. torque shall be specified as per conditions given in Chapter 6 of Part IV of Doc. MoSRTH / CMVR / TAP-115 / 116 Issue No 3.6.12Location of engine (Front / Rear)A6.0 Engine (Type within the Family)A6.1Type (NA/TC/TCIC, DI/IDI)A6.2Manufacturer's name & Manufacturing Plant address.A6.3Working principle (four / two stroke)A6.4Model name and identificationA6.5Type of fuel usedA6.6No.& Layout of cylinders & firing orderA6.7Swept volume (cc)A6.8Bore(mm)A6.9Stroke (mm)A6.10Compression ratio (specify tolerance)7.0Fuel tank (Metallic/Non Metallic)7.1Make7.2Material7.3Capacity7.4Position7.5Test report for non-metallic fuel tank (if provided) (as per IS / ISO : 21507 :2010) 7.6Identification No./Part No.8.0Transmission system8.1Mechanism from engine to transmission8.2Reduction ratio from engine to transmission8.3Clutch8.3.1Make 8.3.2Type (wet/Dry/Single plate/ Multi plate / Hydraulic)8.3.3Control system8.4Facing8.4.1Make 8.4.2Dimension (mm)8.4.3Area (cm2)8.4.4Number of operating faces8.4.5Material8.5Transmission clutch fluid capacity8.6Booster type8.6.1Make8.6.2Type9.0Control system9.1Gear ratio 9.1.11st 9.1.22nd 9.1.33rd 9.1.44th 9.1.55th 9.1.66th 9.1.7Reverse9.2Sub transmission9.2.1Type9.3Gear ratio9.3.1High9.3.2Low9.4Propeller shaft9.5Length inside & outside diameter, mm9.5.11st 9.5.22nd 9.5.33rd 9.5.44th 9.6Universal joint9.6.1Type 9.6.2Number9.7Crown wheel9.7.1Type 9.7.2Reduction ratio9.8Differential 9.8.1Type9.9Running system9.9.1Front axle9.9.1.1Type 9.9.1.2Toe-in (mm)9.9.1.3Camber angle9.9.1.4Caster angle9.9.1.5King pin angle9.9.1.6Trial (mm)9.9.2Rear axle9.9.2.1Type 9.9.2.2Toe-in (mm)9.9.2.3Camber angle9.9.2.4Caster angle9.9.2.5King pin angle9.9.2.6Trial (mm)10.0Steering system as per AIS 14410.1Type10.2Steering wheel Position10.3Outside diameter mm10.4Maximum number of rotations of steering wheel from lock to lock10.5Type of axis & joint10.6Steering gear type10.7Steering gear ratio 10.8Steering angle10.8.1Inside10.8.2Outside10.9Booster10.9.1Make10.9.2Type10.9.3Kind of oil10.9.4Oil capacity (l) 10.10Locking device10.10.1Make10.10.2Type10.10.3Mounting position10.11Steering Effort in (Kg/N) as per AIS 144 11.0Tyres / Rubber track 11.1No. and arrangement of wheels / Rubber Track11.1.1Front 11.1.2Rear 11.1.3Others 11.2Tyre type (Radial/cross ply), size & ply rating11.2.1Front wheel11.2.2Rear wheel11.2.3Other 11.3Rolling radius (mm)11.3.1Static11.3.2Dynamic (if data is available)11.4Inflation pressure – Unladen (kg/cm2 / kPa) 11.4.1Front11.4.2Rear11.4.3Other 11.5Inflation pressure – Laden (kg/cm2 / kPa )11.5.1Front11.5.2Rear11.5.3Other 11.6Makes:11.7Tread Wear Indicator, Provided (Yes/No)11.8Month & Year code of manufacture, Provided (Yes/No)11.9Maximum loading capacity, Provided (Yes/No)12.0Wheel rim12.1Size12.1.1Front12.1.2Rear12.1.3Others12.2Make12.3Identification No./Part No.12.4Pitch circle dia. of mounting bolts (mm)12.5Number of mounting bolts12.6Material (Steel/ Aluminum alloy etc.)13.0Braking system13.1Service brake (Description with Brake circuit diagram)13.1.1Make13.1.2Type (Mechanical/hydraulic/air/air assisted/vacuum assisted/other)13.2Secondary brake (Description)13.2.1Make13.2.2Type13.3Control system & braking wheel13.4Dimensions of lining or pad, ( L x W x t )13.4.1Front wheels (mm)13.4.2Rear wheels (mm)13.5Area of lining or pad (cm2 )13.5.1Front wheels (cm2)13.5.2Rear wheels (cm2)13.6Brake drum or disc effective diameter (mm)13.6.1Front wheel13.6.2Rear wheel 13.7Lining or pad13.7.1Make13.7.2Material (Asbestos / Asbestos free)13.8Master cylinder or brake valve13.8.1Make 13.8.2Type13.8.3Operating stroke (mm)13.9Inner diameter of master cylinder (mm)13.10Type of supply tank13.11Wheel cylinder/wheel chamber13.11.1Diameter (mm) 13.11.1.1Front Wheel13.11.1.2Rear Wheel13.11.2Type (Single acting/Double acting)13.11.2.1Front Wheel 13.11.2.2Rear Wheel13.11.3Make of wheel cylinder/slave cylinder13.11.3.1Front Wheel 13.11.3.2Rear Wheel 13.12Booster13.12.1Make13.12.2Type13.12.3Booster Ratio13.12.4Size of the booster 13.13Air compressor & others13.14Vacuum or air assistance 13.15Air pressure (kg/cm2)13.15.1Nominal pressure 13.15.2Cut in 13.15.3Cut out13.16Type of vacuum pump or air compressor13.16.1Air compressor cubic capacity (cc)13.17Type of pressure regulator13.18Tank13.18.1Position13.18.2Capacity (l)13.19Brake pipe13.19.1Make13.19.2Material13.19.3Rust proof treatment13.20Brake hose (Hydraulic)13.20.1Make 13.20.2Identification mark / Part Number13.30.3Length of hose (mm)13.20.4Nominal bore diameter (mm)13.20.5End fitting type13.20.6Material13.20.7Thickness of lining (mm)13.21Brake fluid13.21.1Make 13.21.2Trade name13.21.3Specification / grade as per Indian standard13.22Braking force (stepping force kg)13.23Type of braking force control system13.24Failure Warning device for braking13.24.1Type (Visual display/ audible/other)13.25Operation pressure (kg./cm2 )13.26Type of safety device13.27Parking brake13.27.1Make13.27.2Type 13.27.3Braking wheel13.27.4Acting on transmission/wheel13.28Lining13.28.1Make13.28.2Dimension of lining or pad (L x W x t)13.28.2.1Front wheel (mm)13.28.2.2Rear wheel (mm)13.28.3Area of lining pad13.28.3.1Front 13.28.3.2Rear13.28.4Material 13.29Diameter of brake drum, mm 13.30Braking force (Operation force kg.)13.31Auxiliary brake 13.31.1Type13.31.2Performance13.32Emergency brake13.32.1Type13.32.2Performance14.0Suspension system14.1Front axle14.1.0Make14.1.1Type of suspension (Leaf/Coil/Air/Semi-pneumatic/Torsion bar)14.1.2Type of spring14.1.3Dimension of main spring (mm) –if leaf spring14.1.3.1Stack height, at centre 14.1.3.2Width at the centre point/Stack point14.1.3.3Flat length14.1.3.4Free camber14.1.3.5No. of Leaves LeftRightNo. of Spacers14.1.3.6Dimension of auxiliary spring (mm)-if leaf spring 14.1.3.7Stack height, at centre 14.1.3.8Width at the centre point/ stack point14.1.3.9Flat length 14.1.3.10Free camber 14.1.3.11No. of Leaves LeftRightNo. of Spacers14.2Rear axle14.2.0Make 14.2.1Type of suspension (Leaf/Coil/Air/Semi-pneumatic/Torsion bar)14.2.2Type of spring14.2.3Dimension of main spring (mm)-if leaf spring 14.2.3.1Stack height, at centre 14.2.3.2Width at the centre point/stack point 14.2.3.3Flat length14.2.3.4Free camber14.2.3.5No. of Leaves Left RightNo. of Spacers14.2.3.6Dimension of auxiliary spring (mm)- if leaf spring 14.2.3.7Stack height, at centre 14.2.3.8Width at the centre point/Stack point 14.2.3.9Flat length14.2.3.10Free camber 14.2.3.11No. of Leaves LeftRightNo. of Spacers14.3Type of shock absorber 14.3.1Front wheel 14.3.2Rear wheel14.4Type of stabilizer14.4.1Front wheel14.4.2Rear wheel15.0Chassis frame15.1Type15.2Cross sectional view15.3Dimension, mm 15.4Type of side protection device 16.0Windscreen wiping system16.1Wind screen wiper16.1.1Type (manual/power)16.1.2No. of wipers16.2Wiper motor16.2.1Make16.2.2Type and identification16.2.3Rated voltage16.2.4Number of sweep Frequencies16.2.5Highest sweep frequency (cycles/min)16.2.6Lowest sweep frequency (cycles/min)16.3Wiper arm16.3.1Length16.3.2Make and Identification16.4Wiper blade16.4.1Length16.4.2Make and Identification16.4.3Rubber material16.5Type of fixing (as per IS 7827)16.6H point16.7Windscreen washing system16.7.1Washer Tank16.7.1.1Type 16.7.1.2Make16.7.1.3Identification No. / Part No.16.7.1.4Capacity.16.7.1.5Material 16.7.2Washer tank motor/ washer pump16.7.2.1Make16.7.2.2Model 16.7.2.3No. of nozzles16.8Type16.9Make16.10Demist / Defroster16.11Type16.12Make17.0Equipment for safety17.1Seat belt anchorages (IS / ISO 6683 : 2005)17.1.1Make17.1.2Type17.1.3Number17.1.4Drawing showing anchorage points and details and Operators Seat Dimensions and requirements as per IS/ISO 11112:199517.2Seat belt (IS / ISO 6683 : 2005)17.2.1Make17.2.2Type17.2.3Number17.3Head restraint17.3.1Make17.3.2Type 17.3.3Number17.4Type of room safety device17.5Type of air conditioner17.6Position of emergency exit17.7Type of device preventing vehicle starting with door opened18.0Safety Glass18.1Front wind shield (Laminated)18.1.1Make18.1.2Identification: TAC No./BIS Licence No./E-marking18.1.3Type (Flat /curved. Clear/tinted)18.1.4Thickness, mm18.1.5Radius of curvature if curved18.2Glasses other than front wind shield18.2.1Make 18.2.2Identification: TAC No./BIS Licence No./E-marking18.2.3Type (Flat/curved, clear/tinted) 18.2.4Thickness ,mm18.2.5Radius of curvature if curved19.0Rear view mirror ( as per AIS 001 (Rev.1) and AIS 002 (Rev.1)19.1Left19.1.1Make 19.1.2Identification: TAC No./BIS Licence No./E-marking19.1.3Type & Class of mirror19.1.4Area and radius of curvature of reflecting surface 19.2Right19.2.1Make 19.2.2Identification: TAC No./BIS Licence No./E-marking19.2.3Type & Class of mirror19.2.4Area and radius of curvature of reflecting surface19.3Inside (AIS 001 (Part 1) / (Part 2) (Rev.1))19.3.1Make 19.3.2Identification: TAC No./BIS Licence No./E-marking19.3.3Type & Class of mirror19.3.4Area and radius of curvature of reflecting surface19.4Camera Monitoring devices (if fitted)19.4.1Name of producer19.4.2Type 19.4.3Position20.0Horn 20.1Make 20.2Type (As per IS 1884:1993)20.3Operating voltage20.4Identification: TAC No./BIS Licence No./E-marking20.5Number20.6Sketch showing mounting of horn21.0Controls (Specify method of operation)21.1Ignition21.2Horn21.3Lamps (Head lamp, Tail lamp, Parking lamp and Number plate lamp)21.4Turn signal21.5Transmission shift lever21.6Wind shield wiper21.7High beam/low beam21.8Parking brake21.9Master switch for electrical21.10Hazard warning signal21.11Service Brake21.12Accelerator Pedal (Floor hinged/hanging type)21.13Others22.0Visual displays and tell tales (IS/ISO 6011, IS/ISO 6405 Part 1, Part 2) for vehicles covered under IS/ISO 6165All other CEV’s -The mandatory requirements as per AIS-071 (Part 1&2). Complies (yes/no)(Indicate the type of tell tales provided and whether they are symbols or letters)22.1Head lamp – upper / lower control22.2Ignition cut-off22.3Turn signal22.4Fuel Gauge22.5Engine coolant temperature22.6Low oil pressure22.7High beam indicator22.8Electrical charge indicator22.9Brake failure22.10Battery Charging22.11Engine oil22.12Horn22.13Speedometer22.14Odometer23.0Auto lamps (bulbs) 23.1Head lamp bulb (main and dip)23.1.1Make 23.1.2Identification: TAC No./BIS Licence No./E-marking23.1.3Designation as per AIS-03423.2Parking Lamp bulb – Front23.2.1Make 23.2.2Identification: TAC No./BIS Licence No./E-marking23.2.3Designation as per AIS-03423.3Parking Lamp bulb – Rear23.3.1Make 23.3.2Identification: TAC No./BIS Licence No./E-marking23.3.3Designation as per AIS-03423.4Direction indicator lamp bulb - front23.4.1Make 23.4.2Identification: TAC No./BIS Licence No./E-marking23.4.3Designation as per AIS-03423.5Direction indicator lamp bulb - rear23.5.1Make 23.5.2Identification: TAC No./BIS Licence No./E-marking23.5.3Designation as per AIS-03423.6Direction indicator lamp bulb - side23.6.1Make 23.6.2Identification: TAC No./BIS Licence No./E-marking23.6.3Designation as per AIS-03423.7Front Position Lamp bulb23.7.1Make 23.7.2Identification: TAC No./BIS Licence No./E-marking23.7.3Designation as per AIS-03423.8Rear Position Lamp ( tail lamp )Bulb23.8.1Make 23.8.2Identification: TAC No./BIS Licence No./E-marking23.8.3Designation as per AIS-03423.9Stop lamp bulb23.9.1Make 23.9.2Identification: TAC No./BIS Licence No./E-marking23.9.3Designation as per AIS-03423.10Number plate lamp bulb23.10.1Make 23.10.2Identification: TAC No./BIS Licence No./E-marking23.10.3Designation as per AIS-03423.11End out Marker bulb 23.11.1Make 23.11.2Identification: TAC No./BIS Licence No./E-marking23.11.3Designation as per AIS-03423.12Reversing lamp bulb 23.12.1Make 23.12.2Identification: TAC No./BIS Licence No./E-marking23.12.3Designation as per AIS-03423.13Stop Lamp Bulb (S3)23.13.1Make 23.13.2Identification: TAC No./BIS Licence No./E-marking23.13.3Designation as per AIS-03423.14Front Fog Lamp Bulb 23.14.1Make 23.14.2Identification: TAC No./BIS Licence No./E-marking23.14.3Designation as per AIS-03423.15Rear Fog Lamp Bulb23.15.1Make 23.15.2Identification: TAC No./BIS Licence No./E-marking23.15.3Designation as per AIS-03423.16Side Marker Lamp Bulb23.16.1Make 23.16.2Identification: TAC No./BIS Licence No./E-marking23.16.3Designation as per AIS-03424.0Lighting equipment24.1Head lamp 24.1.1Main beam24.1.1.1Make 24.1.1.2Type of lens (Glass / Plastic)24.1.1.3Identification: TAC No./BIS Licence No./E-marking24.1.1.4Number and Colour of Lens24.1.2Dipped beam24.1.2.1Make 24.1.2.2Type of lens (Glass / Plastic)24.1.2.3Identification: TAC No./BIS Licence No./E-marking24.1.2.4Number and Colour of Lens24.2Front Fog Lamp 24.2.1Make 24.2.2Type of lens (Glass / Plastic)24.2.3Identification: TAC No./BIS Licence No./E-marking24.2.4Number and Colour of Lens24.3Rear Fog Lamp 24.3.1Make 24.3.2Type of lens (Glass / Plastic)24.3.3Identification: TAC No./BIS Licence No./E-marking24.3.4Number and Colour of Lens24.4Side Marker lamps 24.4.1Make 24.4.2Type of lens (Glass / Plastic)24.4.3Identification: TAC No./BIS Licence No./E-marking24.4.4Number and colour of Lens24.5Registration Plate lamp 24.5.1Make 24.5.2Type of lens (Glass / Plastic)24.5.3Identification: TAC No./BIS Licence No./E-marking24.5.4Number and colour of Lens24.6Position lamp / Parking Lamp - Front24.6.1Front Position Lamp24.6.1.1Make 24.6.1.2Type of lens (Glass / Plastic)24.6.1.3Identification: TAC No./BIS Licence No./E-marking24.6.1.4Number and colour of Lens24.6.2Front Parking Lamp24.6.2.1Make 24.6.2.2Type of lens (Glass / Plastic)24.6.2.3Identification: TAC No./BIS Licence No./E-marking24.6.2.4Number and colour of Lens24.7Position lamp / Parking Lamp - Rear24.7.1Rear Position Lamp24.7.1.1Make 24.7.1.2Type of lens (Glass / Plastic)24.7.1.3Identification: TAC No./BIS Licence No./E-marking24.7.1.4Number and colour of Lens24.7.2Rear Parking Lamp24.7.2.1Make 24.7.2.2Type of lens (Glass / Plastic)24.7.2.3Identification: TAC No./BIS Licence No./E-marking24.7.2.4Number and colour of Lens24.8Stop lamp (S1 / S2)24.8.1Make 24.8.2Type of lens (Glass / Plastic)24.8.3Identification: TAC No./BIS Licence No./E-marking24.8.4Number and colour of Lens24.9Reversing lamp 24.9.1Make 24.9.2Type of lens (Glass / Plastic)24.9.3Identification: TAC No./BIS Licence No./E-marking24.9.4Number and colour of Lens24.10Direction indicator Lamp 24.10.1Front24.10.1.1Make 24.10.1.2Type of lens (Glass / Plastic)24.10.1.3Identification: TAC No./BIS Licence No./E-marking24.10.1.4Number and colour of Lens24.10.2Rear24.10.2.1Make 24.10.2.2Type of lens (Glass / Plastic)24.10.2.3Identification: TAC No./BIS Licence No./E-marking24.10.2.4Number and colour of Lens24.10.3Side24.10.3.1Make 24.10.3.2Type of lens (Glass / Plastic)24.10.3.3Identification: TAC No./BIS Licence No./E-marking24.10.3.4Number and colour of Lens24.10.4Type of flasher24.11Hazard warning signal 24.11.1Front24.11.1.1Make 24.11.1.2Type of lens ( Glass / Plastic )24.11.1.3Identification: TAC No./BIS Licence No./E-marking24.11.1.4Number and Colour of lens24.11.2Rear24.11.2.1Make 24.11.2.2Type of lens ( Glass / Plastic )24.11.2.3Identification: TAC No./BIS Licence No./E-marking24.11.2.4Number and Colour of lens24.11.3Side24.11.3.1Make 24.11.3.2Type of lens ( Glass / Plastic )24.11.3.3Identification: TAC No./BIS Licence No./E-marking24.11.3.4Number and Colour of lens25.0Reflector25.1Front25.1.1Make 25.1.2Type 25.1.3Identification: TAC No./BIS Licence No./E-marking25.1.4Number and colour of lens 25.1.5Reflective surface area 25.1.6Shape (Square/rectangle/circular/elliptical/other) 25.2Rear25.2.1Make 25.2.2Type 25.2.3Identification: TAC No./BIS Licence No./E-marking25.2.4Number and colour of lens 25.2.5Reflective surface area25.2.6Shape(Square/rectangular/circular/elliptical/other) 25.3Side25.3.1Make 25.3.2Type 25.3.3Identification: TAC No./BIS Licence No./E-marking25.3.4Number and colour of lens 25.3.5Reflective surface area 25.3.6Shape (Square/rectangle/circular/elliptical/other) 25.4Yellow flasher25.4.1Make25.4.2Type & identification 25.4.3Number and colour 25.4.4Performance 25.5Warning device horn (When vehicle is reversing)25.5.1Make 25.5.2Type & identification 25.5.3Number 25.5.4Performance 25.6Visibility ensuring device (Reflective tape or reflective paint)25.6.1Width of reflective tape or reflective paint 26.0Meters26.1Speedometer26.1.1Make 26.1.2Model26.1.3Type 26.7.4Range 26.7.5Major marking26.7.6Minor marking 26.7.7Speedometer ratio26.7.8Ratio of speedo drive 26.2Odometer 26.2.1Make 26.2.2Model26.2.3Type 26.2.4Performance & error 26.3Tachograph26.3.1Make 26.3.2Model26.3.3Type26.3.4Performance & error 26.4Pressure gauge26.4.1Make 26.4.2Model 26.4.3Type 26.4.4Performance 26.5Engine speed indicator26.5.1Make 26.5.2Model 26.5.3Type 26.5.4Performance 26.6Pressure container 26.6.1Make26.6.2Capacity of make26.6.3Max. Pressure for use (kg/cm2)26.6.4Material26.7List of spare tools normally given with the vehicle27.0Common / Specific Symbols for operator controls and other displays as per IS/ISO: 6405-1: 2017 and IS/ISO: 6405-2: 2017. 28.0Compliance of Machine Safety Labels as per IS/ISO: 9244:2008. (Yes/No)29.0Compliance of Operator Station and Maintenance Areas as per IS/ISO: 12508:1994. (Yes/No)(Yes/No)30.0Compliance of Minimum Access Dimensions as per IS: 10689:1993/ ISO: 2860:1992, as applicable. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)31.0Compliance of Access Systems for steps, primary access, alternate exit path and opening, maintenance opening, handrail and handholds, as per IS/ISO: 2867:2011, as applicable.(Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)32.0Compliance of Guards - Barrier Guards, Fenders, Fan Guards, Thermal Guards, and Hose Guards as per IS/ISO: 3457:2003. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)33.0Compliance of Machine mounted audible travel alarms and forward horn as per IS/ISO:9533-2010. (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)34.0Operator Controls as per IS/ISO: 10968:2004. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)35.0Compliance of Performance requirements for Articulated Frame Lock as per IS/ISO: 10570:2004. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)36.0Compliance of Lift Arm Support Device as per IS/ISO: 10533:1993/Amd 1:2005. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)37.0Compliance of Electro Magnetic Compatibility (EMC) as per ISO 13766 (Part 1):2018 and ISO 13766 (Part 2):2018. (Yes/No)(Yes/No)38.0Compliance of Roll over Protective Structure (ROPS) as per IS/ISO 3471:2008 as applicable. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)39.0Compliance of Roll Over Protective Structure (ROPS) which shall be provided for excavators as per IS/ISO 12117-2:2008 as applicable. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)40.0Compliance of Tip over protection structure (TOPS) for compact excavators as per ISO 12117:1997, as applicable. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)41.0Compliance of Seat Index Point as per ISO 5353:1995/ IS 11113:1999. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)42.0Compliance of Physical Dimension of Operator and Minimum Operator Space as per IS/ ISO 3411:2007. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)43.0Compliance of Falling Object Protective Structure (FOPS) as per IS/ISO 3449:2005 as applicable. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)44.0Compliance of Operator Field on View as per IS/ISO 5006: 2017. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)45.0Compliance of Installation requirement of rear view mirrors as per ISO:14401-1:2009 and IS/ISO:14401-2:2009. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)46.0Compliance of Zones of Comfort and Reach for Controls as per ISO 6682:1986/IS 11252:1993. (Yes/No)(Yes/No)47.0Compliance of Evaluation of Operator Seat Vibrations for suspended seats if fitted, as per IS/ISO 7096:2000. (Yes/No) (Only applicable for CEV which are covered under scope of IS/ISO 6165:2012)(Yes/No)48.0Compliance of Noise Levels as per CMV Rule 120 complied (Yes/No)(Yes/No)49.0Compliance of Operator Position(dB)-Static & Dynamic - IS/ISO 6394 :2008& IS/ISO 6396 : 2008(Yes/No)50.0Compliance of Machine (dB)- Static & Dynamic- IS/ISO 6393 :2008& IS/ISO 6395 : 2008(Yes/No)51.0Additional information, if any ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download