Ethan Frome - Concrete, Sand, Stone, Gravel and ...



Tech. & Data Sheet

|CURE-CRETE PLUS |

| | | |

|PRODUCT NAME |COVERAGE |LIMITATIONS |

| |Curing and Sealing New Concrete 300 to 400 (7.4 to |• Material will not freeze in storage but should be |

|CURE-CRETE PLUS |9.8) 400 to 450 (9.8 to 11.0) |allowed to rise to 50°F (10°C) before use. |

| |Sealing Older Concrete 400 to 450 (9.8 to 11.0) 450 |• Do not apply when concrete surfaces or ambient |

|MANUFACTURER & DISTRIBUTOR OF INDUSTRIAL CHEMICALS |to 550 (11.0 to 13.5) |temperatures are below 40oF (4°C). Application in hot|

|1611 GUNN HIGHWAY |Coverage will vary from the above rates depending on |direct |

|ODESSA, FLORIDA 33556 |surface porosity and texture. AVOID EXCESSIVE |sunlight, or when the concrete and/or air temperature|

|(813) 886-8811 |BUILDUP. |is 90°F (32°C) and rising, may cause bubbling. |

| |HEAVY APPLICATIONS WILL LEAD TO DISCOLORATION AND |• Do not apply over bleed water or free standing |

|PRODUCT DESCRIPTION |POOR PRODUCT PERFORMANCE. |water. |

|CURE-CRETE PLUS is a solvent based curing and sealing | |• Use with adequate ventilation and keep away from |

|compound specially designed to cure new |APPLICATION |open flames. Block all HVAC ventilation ducts which |

|concrete, assuring proper cement hydration and |Surface Preparation: The concrete surface must be |may |

|strength gain, while providing a non-yellowing seal to|clean and free of standing water. Remove any curing |distribute solvent odor. If solvent odor is |

|protect |compounds, sealers, or other material that may |objectionable, use of a water based, low odor product|

|and enhance the appearance of concrete. This product |prevent adhesion of the CURE-CRETE PLUS. |such as CURE-CRETE WB may be preferred. |

|is suitable for use on interior and exterior concrete |Mixing: CURE-CRETE PLUS requires no preblending and |• For a high gloss finish, two thin coats of |

|surfaces. CURE-CRETE PLUS has excellent bonding |should be used directly from the container. |CURE-CRETE PLUS is suggested rather than one heavy |

|characteristics and forms a continuous, glossy |Application: Apply at a uniform coverage by spray or |application. Apply the second coat within 24 hours of|

|membrane to make the surface resistant to dirt |roller application. Product must be sprayed with a |the first. |

|penetration and other staining. CURE-CRETE PLUS is |high |• Do not apply over concrete to receive toppings, |

|particularly suited for curing and sealing exterior |pressure pump-up sprayer equipped with a high solids |epoxy or urethane-based coatings or adhesives. |

|concrete where membrane yellowing is undesirable. |nozzle, or with an airless industrial sprayer. If |• Although compatible with many carpet, tile and |

| |roller |floor covering adhesives, a test section is |

|ALTERNATE USES |applied, use a short napped, solvent resistant |recommended to |

|• Driveways & exterior pavements |sleeve. Keep a wet edge while spraying and backroll |ensure good bond between the adhesive and CURE-CRETE |

|• Walls and columns |over sprayer |PLUS. |

|• Terrazzo floors |lap marks for best appearance. |• Do not use as a bond breaker for tilt-up |

|• Parking garages |Curing and Sealing: For the best cure of freshly |construction. |

|• Exposed aggregate |placed concrete, apply CURE-CRETE PLUS as soon as |• Do not use in areas subjected to hot grease or |

|• Dry shake floors |possible after finishing operations and/or |oils. |

|• Freight terminals |immediately after the disappearance of the “sheen” of|• Not resistant to gasoline or brake fluid. |

|• Curing and sealing decorative concrete |surface moisture. |• Do not thin this product. |

| |When sealing old concrete, the surface must be |• In all cases, consult the Material Safety Data |

|FEATURES/BENEFITS |thoroughly clean and dry. Pressure washing with a |Sheet before use. |

|• Helps promote development of concrete strength and |strong | |

|durability |alkaline detergent to remove dirt, waxes, and oil is |CLEAN UP |

|• Dustproofs concrete with a tough durable film |suggested. Acids will not sufficiently clean or |Use toluene, xylene, or INCRETE SOLV-KLEEN for |

|• Helps minimize spalling of exterior concrete |remove dirt, |cleaning tools. |

|• Will not yellow under ultraviolet exposure |curing compounds, or old sealer from concrete. Worn | |

| |or porous areas may need a second application for | |

|PACKAGING |uniform |AVAILABILITY AND COST |

|CURE-CRETE PLUS is packaged in 55 gal (208 L) drums |seal and appearance. NOTE: When sealing decorative |Available through a large network of paint dealers |

|and 5 gal (18.9 L) pails. |concrete, the use of INCRETE CLEAR SEAL or CRYSTAL |located throughout the USA. For availability in other|

| |CLEAR is recommended for best performance and |areas, contact manufacturer. Cost will vary with |

|TECHNICAL DATA |appearance. |location. |

|Typical Engineering Data |WARRANTY | |

|The following results were developed under laboratory |All recommendations, statements and technical data | |

|conditions. |contained herein based on tests we believe to be | |

|Drying time* @ 73°F, 50% |reliable and correct, but accuracy and completeness |IMPORTANT NOTICE |

|RH.............................................. 25% |shall not be binding upon the manufacturer or seller.|NON-CONFORMING GOODS AT THE OPTION OF THE SELLER. |

|Moisture loss (ASTM C 156)..< 0.40 kg/m2 | |SUCH REMEDY BEING EXCLUSIVE OF ALL OTHERS AND THE |

|* Low concrete or air temperature and/or high relative| |SOLE REMEDY AVAILABLE TO THE BUYER, HEREBY EXPRESSLY |

|humidity will extend drying time. | |WAIVES ANY CLAIM TO ADDITIONAL DAMAGES. |

|Appearance: CURE-CRETE PLUS is a water clear liquid. | | |

|After application and drying, CURE-CRETE PLUS offers a| | |

|clear, glossy film. CURE-CRETE PLUS will darken | | |

|concrete, masonry, pavers, etc., giving these | | |

|materials a “wet” look. Follow recommended coverage | | |

|rates carefully for best appearance. | | |

| | | |

|APPLICABLE STANDARDS | | |

|• ASTM C 309, Type 1, Class A & B | | |

|• ASTM C 1315, Type 1, Class A | | |

|• AASHTO Specification M 148, Type 1, Class A & B | | |

|• USDA compliant | | |

| | | |

|SHELF LIFE | | |

|3 years in original, unopened container. | | |

| | | |

|REMOVAL | | |

|Dried, cured sealer may be removed with strong | | |

|solvents such as INCRETE SOLV-KLEEN, xylene, or | | |

|toluene. Also acceptable are commercial paint | | |

|strippers (always heed directions and warning labels).| | |

|INCRETE UNI-STRIPP is a citrus-based stripper that can| | |

|also be used to remove this product. Alternately, the | | |

|sealer can be removed by sandblasting or by other | | |

|similar mechanical action. | | |

| | | |

|TECHNICAL SERVICES | | |

|Over 40 years of sealer manufacturing makes INCRETE | | |

|personnel the most knowledgeable in the field of | | |

|concrete sealers. A highly educated and well-trained | | |

|technical staff is available. Call or contact (813) | | |

|886-8811. | | |

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download