REQUEST FOR PROPOSAL - North Carolina
Johnston Community CollegeREQUEST FOR PROPOSAL FOR GUARANTEED ENERGY SAVINGS PERFORMANCE CONTRACTING Date September 19, 2017RFP # 104-0282017REQUEST FOR PROPOSALS FORJohnston Community CollegeSTATE OF NORTH CAROLINAGUARANTEED ENERGY SAVINGS PERFORMANCE CONTRACTTABLE OF CONTENTSPage PART 1 – GENERAL INFORMATION3PART 2 – PROPOSED PROJECT SCHEDULE9PART 3 – EVALUATION PROCESS AND CRITERIA11PART 4 – Submission of Proposals12SIGNATURE PAGE (to be first page of Proposal)23 ATTACHMENT A – PRELIMINARY ECM COST / SAVINGS MATRIX - Do not submit 24with response ATTACHMENT B – ESCO's PRELIMINARY COST PROPOSAL25 (Using best rate ESCO can arrange) - Do not submit with responseATTACHMENT C – PRELIMINARY ANNUAL CASH FLOW ANALYSIS27 (Using ESCO’s Rate) - Do not submit with responseAPPENDIX I – FACILITIES TO BE ANALYZED APPENDIX II – DESIGN REQUIREMENTS APPENDIX III – MINIMUM INSURANCE REQUIREMENTSJohnston Community CollegeSTANDARD REQUEST FOR PROPOSALGUARANTEED ENERGY SAVING PERFORMANCE CONTRACTGENERAL INFORMATION Issuing Office: This RFP is issued by Johnston Community College (hereinafter referred to as “ISSUER”). The following Issuing Officer is the sole point of contact for this RFP: Michael Massey919-209-2087245 College Rdmtmassey@johnstoncc.eduSmithfield, NC 27577Purpose. This Request for Proposals (RFP) contains the information provided by ISSUER and requirements for Qualified Providers as defined in Chapter 143 Article 3B Part 2 of the General Statutes (hereinafter referred to as “ESCO”) and submit to the ISSUER a Preliminary Technical Proposal for a guaranteed energy savings contract (referred to herein as the “Guaranteed Energy Savings Contract”). The ESCO’s response to this RFP (the “Proposal”) must be based on the ESCO’s assessment of the facilities selected by the ISSUER and listed in Appendix I. The ISSUER reserves the right to consider additional energy conservation measures as that term is defined in Chapter 143 Article 3B Part 2 of the General Statutes (“ECMs”) identified during the investment grade audit for evaluation and inclusion in the project. This RFP, including any amendments, contains the only instructions governing the proposals and material to be included therein; a description of the service to be provided by the successful applicant; general evaluation criteria; and other proposal requirements.Mandatory pre-proposal meeting: A mandatory pre-proposal Meeting will be conducted by Johnston Community College on September 27, 2017, at 2:00 PM in the Wilson Administrative Building, Pines Board Room C1001 . Any questions should be directed to Issuing Officer identified in 1.1.Proposals from ESCOs who fail to attend the pre-proposal meeting will receive no consideration.ALL PROPOSALS WILL BE RECEIVED, OPENED AND ANNOUNCED on November 21, 2017 at 2:00 PM in the Wilson Administrative Building, conference room C1013.REQUIRED INFORMATION MUST BE SENT TO THE FOLLOWING ADDRESS: Johnston Community CollegeAttention: Cassandra Haire245 College RdSmithfield, NC 27577 Mark on the lower right corner of the submittal: RFP # 104-0282017Objective: The objective of the ISSUER in issuing this RFP is to maximize energy cost saving and related costs in order to pay for facility upgrades to the facilities listed in Appendix I and services that will be financed through a Guaranteed Energy Savings Contract at no cost to the ISSUER. The services may include but are not limited to: (1) A preliminary audit to be performed on the project sites identified in Appendix I in accordance with § 143-64.17A, (2) The highest ranked qualified provider will prepare a cost benefit analysis conducted in accordance with Attachments A, B and C on the measures identified in the preliminary audit, (3) An investment grade audit to be conducted on all project sites to identify appropriate ECMs, (4) The design, acquisition, installation, modification, commissioning and maintenance of the ECMs, (5) The training of staff in the operation of existing equipment and new ECMs, (6) Energy and operational cost savings, such as fuel switching, demand reductions, on-site generation, utility bill auditing, utility rate changes, distribution upgrades. Any stipulated energy and/or operational cost savings that may be attributed to this project will be rigorously reviewed and, if agreed to, will be limited to those that can be thoroughly documented and approved by the ISSUER.-228600-121475500No Guaranteed Energy Savings Contract shall exceed 20 years in duration from the date of the installation and acceptance of the project, as defined in § 143-64.17B, and must comply with all other applicable statutes, regulations, and procurement laws. Proposals for this RFP shall not exceed the term stated in section 1.7. The cost savings achieved by the installed ECMs must be sufficient to cover all project costs including annual maintenance and monitoring fees on an annual basis for the duration of the term of the Guaranteed Energy Savings Performance Contract. The ESCO must guarantee sufficient energy savings, as defined in § 14364.17, to enable the ISSUER to meet its payment obligations to the ESCO and the entity financing the Guaranteed Energy Savings Performance Contract. ESCOs will be required to guarantee energy savings on an annual basis. No credit for the achievement of energy savings above and beyond the annual guarantee will be credited to satisfy performance guarantees in other years of the contract. Annual reconciliation of the achieved energy savings will be required.Security Requirements: The Office of State Treasurer has determined that the following general types of security for the guaranteed energy savings would be acceptable, however specific instruments of security as part of a financing contract for energy conservation measures will need to be approved by the Office of the State Treasurer as per N.C.G.S. § 143-64.17B.(c) for each guaranteed energy savings performance contract. These general types are:A corporate guarantee by the ESCO provided that the ESCO has a long-term investment grade corporate rating from one or more of the national credit rating agencies. Currently, this would be a minimum rating of BBB from Standard and Poor’s, Baa from Moody’s Investors Service, or BBB from Fitch Ratings.A corporate guarantee from the parent company of an ESCO which is owned as a subsidiary of the parent. The parent company would be required to maintain a long-term investment grade rating from one or more of the national credit rating agencies (see above.)An irrevocable letter of credit from a financial institution which covers the entire term of the contract, without need of renewal.A surety bond which covers the entire term of the contract, without need of renewal.Financing by the ESCO in which the ESCO provides all financing required for the entire term of the contract. Financing may only be transferred or assigned to the extent that energy savings are realized, and State property may not be encumbered in any form as part of the financing.All forms of security would be required to be in place at the initiation of the guaranteed energy savings performance contract covering (100%) of the guaranteed energy savings for the term of the guaranteed energy savings performance contract. In the case of corporate guarantees, should the guarantor’s credit rating drop below long-term investment grade, the guarantor is required to inform the governmental unit, The Department of Environmental Quality, Utility Savings Initiative (USI), and the Local Government Commission (LGC) within 30 days and replace the corporate guarantee with one of the other forms of security acceptable to Office of the State Treasurer.Description of the Procurement Process: The process for the procurement of these guaranteed energy savings services will proceed as follows:Solicitation of proposals. The ISSUER will issue a request for proposals that is open to all ESCOs who have been prequalified by USI. Notice of the request must be published at least 15 days in advance of the time specified for opening of the proposals in at least one newspaper of general circulation in the geographic area in which the facility or facilities are located. In addition, the ISSUER will place a notice regarding the solicitation on the USI home page with instructions on how to obtain the solicitation. If only one proposal from an ESCO is received, then the ISSUER shall re-issue this RFP unless this is the second release at which time a single response may be accepted.Opening of proposals. Proposals are to be opened in accordance with the instructions in Section 1.3. All proposals received by the specified time will be opened by a member or employee of the ISSUER at a public opening who will announce the name of the ESCO submitting the Proposal and verify the execution of the signature page by the ESCO. Unsigned proposals will be rejected.Evaluation of proposals. Responding ESCOs shall conduct a preliminary audit of the facilities listed in Appendix I. This preliminary audit will form the basis of the ESCOs’ written Preliminary Proposal. The Proposals must be in substantial conformity with Part 4 (Submission of Proposals) and other conditions set forth in the RFP. The ISSUER will evaluate or cause its designated representatives to evaluate the ESCOs’ Preliminary Proposals. The proposal shall be evaluated by a Qualified Reviewer as defined in Chapter 143 Article 3B Part 2 of the General Statutes (“Qualified Reviewer”). The Qualified Reviewer may be selected from the ISSUER’s staff or a third-party engineer or architect may be engaged by the ISSUER. The evaluation shall be based on the criteria listed in Part 3 of this RFP. The Qualified Reviewer shall also review Attachments A, B, and C to determine if project scope, costs and savings are achievable.Client reference checks. The ISSUER shall review and evaluate the ESCO client references provided in the Proposal in accordance with the evaluation criteria identified in Part 3.Shortlist. The ISSUER shall shortlist ESCOs on the basis of the rankings of evaluating the written proposal and the client references using the criteria in Part 3.Oral interview. Each shortlisted ESCO may be required to participate in an oral interview. The purpose of this session is to clarify specific aspects of the technical proposal and to answer questions posed by the evaluation team. These oral interviews may be recorded. ESCO responses given in the oral interview will be part of the overall evaluation, but the ESCO will not be allowed to vary the written Proposal or improve the competitive position of the ESCO.Selection of ESCO to develop the project. The ISSUER shall have the highest ranked ESCO prepare Attachments A, B, and C for the proposed contract. Only the energy conservation measures identified in Part 4 Section 5.1 of the proposal may be included in the attachments. The ISSUER may require that the ESCO competitively bid any of the products or contractors required to implement the project. Copies of all such bids shall be sent to the ISSUER. If the ISSUER and ESCO cannot negotiate acceptable terms, pricing, savings estimates, and percentages the ISSUER or ESCO may terminate the process at which time the ISSUER may begin negotiations with the second highest ranked ESCO. Once the second highest ranked ESCO is engaged the ISSUER may not return to the highest ranked ESCO. The ISSUER’S Qualified Reviewer, shall also review Attachments A, B, and C to determine if project scope, costs and savings are achievable. USI shall review the selected ESCO's proposal, all Attachments, and other relevant documents prior to the ISSUER announcing the award. The ISSUER shall provide published notice of the time and place of the meeting at which it proposes to award the contract, the names of the parties to the proposed contract, and the contract's purpose. This announcement shall be published 15 days prior to award or meeting.The ISSUER shall notify all responders of the ranking results.Type of Contracts: The successful applicant will be required to enter into an Investment Grade Audit Contract (IGAC) and where the ISSUER elects to enter into a Guaranteed Energy Savings Performance Contract (ESA) after the ESCO performs an IGA, the ESCO and ISSUER shall approve the final IGAA and ESA utilizing the latest revisions at that time. The ISSUER may, at its sole discretion, allow certain elements of the contracts to be negotiated. The approved versions of above documents shall be in place prior to the award of the contract. The preferred term of the Guaranteed Energy Savings Contract shall be for a maximum of fifteen (15) years from the date of acceptance of the project, as defined in § 143-64.17B. During the Investment Grade Audit the ISSUER reserves the right to adjust the term based on final cost and interest rate. The ISSUER shall own all installed equipment which shall be free and clear of all liens and encumbrances upon transfer of ownership to the ISSUER.Rejection of Proposals: The ISSUER reserves the right to reject any and all proposals received. If the ISSUER decides to terminate this process the ISSUER shall notify all responders of such decision within 30 days.Incurring Costs: The ISSUER is not liable for any cost or expenses incurred by ESCOs in the preparation of their Proposals or for attendance at any conferences and meetings related to this RFP.Amendments to the RFP: If it becomes necessary to revise any part of this RFP, an addendum will be issued to all ESCOs who attended the mandatory pre-proposal meeting. If any ESCO has questions prior to opening the proposal, those questions must be submitted and answered in writing in accordance with the schedule listed in Part 2. A copy of all questions and answers submitted will be sent to all ESCOs that attended the mandatory pre-proposal meeting.Error / Clarification: When a proposal contains an obvious error or otherwise where an error is suspected, the circumstances may be investigated and then may be considered and acted upon. Any action taken shall not prejudice the rights of the public or other offering companies. Where offers are submitted substantially in accordance with this RFP but are not entirely clear as to the intent or to some particular fact where there are other ambiguities, clarification may be sought and accepted.Restriction of Contact: From the date this RFP is issued until a determination is made regarding the final selection of an ESCO for the Project, all contacts with the ISSUER concerning this RFP shall be made in writing through the Issuing Officer, identified in Part 1.1, only.Debriefing: As a courtesy, the ISSUER will notify in writing ESCOs who are not awarded within a reasonable period following the ISSUER’s selection of an ESCO pursuant to this RFP. The ESCO may request a debriefing with the ISSUER at this time which shall be granted in a reasonable time.Proposals: To be considered, Proposals must include responses to all requests for information in this RFP. Proposals must be straightforward, concise presentations without extraneous material. Font size may be no smaller than 10 point. The ESCO shall make no other use of the proposal. An official authorized to bind the ESCO must sign the proposal. The proposal shall constitute a valid firm offer for 90 days after the opening of proposals submitted pursuant to this RFP. The contents of the proposal of the selected ESCO will become part of the ESCO’s contractual obligations to the extent that the proposal does not conflict with provisions of this RFP.Site Visits: The Issuing Officer or his or her designated representative will arrange inspection tours of the buildings to be audited. Site representatives will be available to escort ESCOs and their representatives through the facilities. Questions arising out of these tours shall be submitted in writing to the Issuing Officer. Technical information supplemental to material contained in this RFP will be made available for review and inspection onsite. Only ESCOs who were represented at the pre-bid are eligible to participate in these site visits.Late Offers, Modifications or Withdrawals: No late offer, late modification, or late withdrawal shall be considered unless received before Opening Date, and the offer, modification, or withdrawal would have been timely but for the action or inaction of one of the ISSUER’s employees or agents. The ESCO shall bear the sole responsibility of having its proposal delivered on time, regardless of the mode of delivery used, including the U.S. Postal Service or any other delivery services available. The time allowed for the acceptance of offers may be extended by the ISSUER.Historically Underutilized Businesses: Pursuant to General Statute 143-48 and Executive Order #150 (1999), the State invites and encourages participation in this procurement process by businesses owned by minorities, women, disabled, disabled business enterprises and non-profit work centers for the blind and severely disabled. ESCO Responsibility: The selected ESCO will be required to assume total responsibility for all services and/or equipment offered in the Proposal. The selected ESCO is responsible for obtaining all applicable permits, reviews and meeting all licensing requirements. The selected ESCO will be considered the Prime Contractor and the sole point of contact with regard to the Project.Payment and Performance Bond: The selected ESCO shall be required to provide construction payment and performance bonds in conformance with NCGS § 44-A, Article 3 and in the amount of 100% of the total financed project cost as shown on Attachment B. The ESCO’s proposal must include the form of two payment and performance security instruments as follows:The first security instrument, a payment and construction performance bond, is to be conditioned for the faithful performance and fulfillment of the installation of the Energy Conservation Measures and which shall be valid until the completion of the installation work, with construction approved by the ISSUER and accepted on behalf of the StateThe second security instrument shall be a written guarantee, which will be contained in the contract, which states that the annual energy or operational costs savings will meet or exceed the total cost of the contract, including (without limitation) financing, installed equipment costs, contract security instruments required by the Office of State Treasurer, an annual fee for a third party engineer, and measurement and verification for the entire length of the contract period. This security instrument must be in a form and amount acceptable to the Office of State Treasurer as listed in Part 1.5.References and Proprietary Information: Submission of a Proposal grants permission to the ISSUER to make inquiries concerning the respondent and its officers to any persons or firms deemed appropriate by ISSUER. Any proprietary information will be treated as provided for in N.C. Public Records Act. Data or information so identified will be used by the ISSUER solely for the purpose of evaluation and contract negotiations.North Carolina Products: Where quality and availability allow, specifications shall be based on products manufactured by and services provided by North Carolina businesses. This special interest in North Carolina products is intended to encourage and promote their use, but shall not be exercised to the exclusion of other products or to prevent fair and open competition.Proposal Funding: The Treasurer may reject any potential contract if the actual cost of financing has exceeded the estimated cost of financing when the contract is submitted to the Office of the Treasurer for approval. The ESCO receiving the contract award shall submit a total contract cost option and cash flow analysis based on ESCO or third party financing at best available rate. This is the basis for Attachment “B” and Attachment “C”.Annual Reconciliation: The energy savings shall be monitored and reported on in accordance with the measurement and verification plan created in the IGA commencing with the date of the Certification of Final Acceptance to be signed by the ISSUER. The reconciliation report is due no more than 60 days from the anniversary of the Certification of Final Acceptance. In the event that the actual savings are less than the guaranteed savings, the ESCO shall provide cash reconciliation of the difference within thirty (30) calendar days of written demand by the ISSUER. A surplus in any one year shall not be carried forward or applied to a shortfall in any other year.Independent Consulting Engineer: The ISSUER may engage an independent third-party professional engineer or architect licensed in North Carolina experienced in the design, installation, and implementation of energy efficiency measures and who shall act as the ISSUER’s representative. This professional shall provide services in the review of the IGA and annual reconciliation report. The ESCO shall include a one-time fee of 1% to 2% of the total project cost for the RFP and IGA review. The ESCO shall also include an annual cost of 1% to 1.5% of annual savings for the consulting engineer or architect to review the reconciliation report. This cost shall be financed and paid from the savings for the contract life.ANTICIPATED PROJECT SCHEDULEJohnston Community CollegeActivityDateIssue RFP and have posted on USI websiteSeptember 19, 2017Mandatory pre-proposal meetingSeptember 27, 2017Site Visits (to be arranged)October 9 - 27, 2017Bid for Third Party Review awarded by JCC TrusteesOctober 16, 2017Questions dueNovember 7, 2017Answers distributedNovember 14, 2017Proposals Received, Opened, and AnnouncedNovember 21, 2017Proposals Reviewed, Evaluated and RankedNovember 27 – December 15, 2017JCC Board of Trustees PresentationJanuary 4, 2018Oral Interviews and selection of ESCOJanuary 18, 2018Highest ranked ESCO completes Attachments A, B and CFebruary 8, 2018JCC Board of Trustees ApprovalMarch 1, 2018Advertise award per section 1.6.7March 7, 2018IGAC NegotiatedMarch 21, 2018IGA ConductedMarch 26 – June 4, 2018USI IGA reviewJune 5, 2018JCC Board of Trustees PresentationJuly 12, 2018Financial RFPJuly 16, 2018Contract Preparation and reviewAugust 6, 2018Local Board approvalFinancial RFP and contractCounty Commission approvalTreasurer & LGC approvalContract Awarded by JCC Board of TrusteesSeptember 6, 2018Contract Presented and Signed by JCC Board ChairSeptember 13, 2018EVALUATION PROCESS AND CRITERIAEach proposal will be reviewed for completeness and scored pursuant to the evaluation criteria as described in this section. Completeness. Responses will be initially evaluated based on the completeness and quality of the information provided in Part 4, ESCO Proposal: Sections 1 through 19, and when requested Attachment A ECM matrices, Attachment B preliminary cost proposal, Attachment C preliminary cash flow analysis. A Proposal will be considered complete if all requested sections are included in the proper order and properly completed. An incomplete Proposal may be disqualified.Evaluation Criteria. The ISSUER may adjust point values and add or delete criterion in the table below as they deem necessary to meet their needs. The ISSUER will utilize the following criteria in its evaluation of proposals:Proposal and ESCO AppraisalCriterionPoint ValueClarity, organization, and level of detail in written proposal5Substantial conformity with RFP requirements10ECMs included meet ISSUER’s expectations as expressed in Appendix I10General reputation, experience, reliability, working relationship and performance capability of the ESCO10Proposed training meets ISSUER’s requirements5Total:40Technical ApproachCriterionPoint ValueESCO identified additional achievable ECMs not referenced in this RFP 10Proposed project delivery approach10Implementation schedule achievable10Proposed plan includes ISSUER’S preferred provider(s) for HVAC Controls Systems10Proposed project-specific Commissioning Approach5Proposed project-specific Maintenance Plan5Proposed project-specific Measurement and Verification Methodology5Understanding of customer’s operation and challenges5Level of commitment to use Local Contractors10Level of commitment to encourage HUB Contractor Participation10Total:80Oral InterviewCriterionPoint ValueDemonstrated clear understanding of the ISSUER’s needs5Answered questions in concise manner staying on topic5Presenters were knowledgeable and professional5Appropriate project specific employees participated in interview10Total:25Grand Total: 145Review of RFP ResponsesThe ISSUER, or their designees, will evaluate each Proposal to this RFP pursuant to criteria listed in section 3.2 above. The evaluators will grade the Proposals on their merit and responsiveness to the needs of the ISSUER. Responses will be evaluated in light of the material and substantiating evidence presented in the Proposal. The evaluation process may include verification of references, confirmation of financial information, and may also include interviews, site visits, or other information as directed by the ISSUER.In accordance with § 14364.17A sections (c) and (c1) the Proposals shall be evaluated by a Qualified Reviewer (to be designated by the ISSUER). The cost of this architect or engineer may be included in the total cost of the contract. Final Selection and NotificationThe ISSUER shall have USI and the qualified reviewer review the selected ESCO's proposal, cost-benefit analysis, and other relevant documents after which the ISSUER shall announce the award.. The ISSUER reserves the right to reject any and all proposals received and is not required to furnish a statement of the reason why a particular proposal was not deemed to be the most advantageous. The ISSUER will reasonably notify each responder of the successful ESCO.SUBMISSION OF PROPOSALS Form of Proposal.All Proposals shall be submitted on “8 ? x 11" sheets of paper (unless specifically exempted from this requirement below) that are numbered sequentially by section (example: 1-1) and use labeled tabs to separate sections. Font size must be no smaller than 10 point, utilizing the front and back of pages. Applicants must also include a Table of Contents that indicates the section and page numbers corresponding to the information included. The Applicant must submit to the ISSUER one original, two hard copies and one electronic copy. When requested by the ISSUER Attachments A, B, and C will be submitted electronically in MS Excel format.Content of Proposal. Each Applicant is required to complete all sections listed below. Section 1: Company Profile and History. The ESCO shall comply with proper contractor licensing requirements to perform construction if selected. Indicate on page one of this section the license under which work will be performed. Include an actual template of the form of security to be provided. The security must be one of the five forms accepted by the Department of State Treasurer (see Part 1.5). (2 page limit double sided the security template may be additional pages)Section 2: Project Summary (2 page limit double-sided)Section 3: Project Team including resumesName of Project Team Member: Current Job Title:Job responsibilities:Number of years with ESCO:Primary Office Location:Employment History Company Name: Primary job responsibilities: Number of years with firm:Educational BackgroundList all academic degrees, certifications, licenses, professional affiliations, relevant publications and technical training.List all energy performance contracting projects this individual has been involved with during past 5 years. Include project location, type of facilities, year implemented and dollar value of installed project costs.Describe the specific role and responsibilities this individual had for each listed project. Provide a detailed description of the role and responsibilities this individual will have for the duration of this project. Describe any other relevant technical experience.Indicate the total years of relevant energy-related experience for this individual.Section 4: Existing Conditions. Section 5: Energy Conservation Measures. Section 5.1: ECMs included in Proposal (limit to one double sided page for each measure). For each ECM provide data in following format: ECMs specified in this section shall be included when completing Attachments A, B and CECM ID _____________________Building or Utility System ID _________________________________IPMVP protocol typically used for this type measure _________________ Assumptions ________________________________________Brief narrative including product recommendations (place all product specification sheets in separate binder) ________________________Section 5.2: ECMs identified but to be investigated during the IGA.Section 5.3: ECMs Considered but not included. Be sure to state reason for rejection.Section 5.4: Details of work that will be performed outside of the United States.Section 6: Operational Savings: ISSUER labor savings may be considered in cost savings only if an occupied position is eliminated as a result of the Project. Include the number of years savings will be realized.Section 7: Project Commissioning Approach. Provide general outline for this project.Section 8: Project M&V Approach, provide general outline. Any guaranteed energy and operational savings shall be determined by using one of the measurement and verification methodologies listed in the United States Department of Energy's "Measurement and Verification Guideline for Energy Savings Performance Contracting," the "International Performance Measurement and Verification Protocol," or "ASHRAE 14-2002." If due to existing data limitations or the nonconformance of specific project characteristics, none of the measurement and verification methodologies listed above is sufficient for measuring guaranteed savings, the ESCO shall develop an alternate method that is compatible with one of the three and mutually agreeable with the ISSUER.Section 9: Project Maintenance Approach for proposed equipment. The plan should describe how ECMs will be maintained over the duration of the contract period. The plan should identify who is responsible for maintaining and repairing equipment installed. In particular it should address how building automation or other electronic systems will be kept updated and current.Section 10: Hazardous Material Handling Approach - describe your firm’s plans for the disposal and recycling of any equipment or materials removed from the premises as part of an ECM. Be sure to include proper tracking of hazardous materials such as lamps and ballasts.Section 11: Implementation Approach and Schedule - provide proposed implementation schedule with milestones. The “8 ? x 11" sheet size limitation does not apply to this section.Section 12: ISSUER Training - describe your approach to training both during implementation and during guarantee period. Provide details on number of participants expected, topics and location for training.Section 13: Project Financing - provide your proposed approach to project financing and assistance. Section 14: Other Project Impacts - provide information on positive and/or negative impacts that the installation of recommended ECMs may have on air quality emissions, waste reduction, health, occupant comfort or other items not specifically requested. This can refer to such non-tangible benefits such as improvements to the learning environment, teaching opportunities, green building considerations, greenhouse gas reductions, anti-drought measuresSection 15: Open Book Pricing - describe your firm’s approach and experience in providing open-book pricing. The ESCO will fully disclose all costs, including all costs of subcontractors and sub-tier vendors. The ESCO will maintain cost accounting records on authorized work performed showing actual costs for labor and materials, or other basis requiring accounting records. The ESCO will provide access to records and preserve them for a minimum of three years and if any federal funds are used to support the Contract, for five years. The retention period runs from the date of payment for the relevant goods or services by the ISSUER or from the date of termination of the Contract, whichever is later. Retention time shall be extended when an audit is scheduled or in progress for a period reasonably necessary to complete an audit and/or to complete any litigation in any forum which may arise.Section 16: References Using the forms included, list at least 3 energy performance contracting projects in repayment by and currently under contract with your firm. Limit your Proposal to ONLY those projects that have been managed directly by the specific branch, division, office or any individual in such branch, division or office who will be specifically assigned to this project. Attach additional sheets as necessary. Please put an asterisk by any project references involving buildings similar to the building(s) described in the Appendix I. Make sure all contact information is current. All information requested is required. Project Table:Project Name and Location; Number of Buildings; Primary Use; Total square footageProject Dollar Amount (installed project costs); Source of Project FinancingPrimary ECMs Installed; ESCO Services ProvidedConstruction Start & End DatesContract Start & End DatesDollar Value and Type of Annual Operational Cost Savings (if applicable) (e.g., outside maintenance contracts, material savings, etc.)Method(s) of Savings Measurement and VerificationProvide CURRENT and ACCURATE telephone and email address orFAX numbers of the owner(s)’ representatives with whom your firm did business on this project. You should ensure that all representatives are familiar with this project.Describe the specific roles and responsibilities of ESCO personnel associated with the identified project. Limit your Proposal to only those personnel who will be directly involved in Customer’s project. ESCO Notes or CommentsAnnual Energy Savings Data Form (Energy Units)Name of Project: Name of ESCO: _______________________ProjectedGuaranteedAchievedCommentsYear 1Year 2Year 3Year 4Year 5KWHKW DemandNat Gas ThermsWater(Gallons)Other (Specify)Other (Specify)Information for each of the headings listed above MUST be completed using the above format. DO NOT provide savings data in terms of BTU’s or dollars. Data should be given in the form of fuel units which appear in the utility bills. Additional forms should be reproduced as needed. Annual Energy Savings Data Form (Energy Dollars)ProjectedGuaranteedAchievedCommentsYear 1Year 2Year 3Year 4Year 5KWHKW DemandNat Gas ThermsWater(Gallons)Other (Specify)Other (Specify)Information for each of the headings listed above MUST be completed using the above format. Provide savings data in terms of dollars for the units saved. Additional forms should be reproduced as needed.Section 17: Submit SEC Form 10-K for the two most recent years in this section. If Form 10-K is not filed then submit the ESCO’s two most recent years audited financial statements. This section may be submitted in electronic form only.Section 18: Risk responsibility matrix:1. RESPONSIBILITY/DESCRIPTIONESCO PROPOSED APPROACH1. Financiala. Interest rates: Neither the ESCO nor the ISSUER has significant control over prevailing interest rates. During all phases of the project, interest rates will change with market conditions. Higher interest rates will increase project cost, financing/project term, or both. Please state your approach to mitigate fluctuating interest rates.b. Energy prices: Clarify how future energy costs will be treated.c. Construction costs: If, during construction, costs may overrun the fixed budget explain how the project will be brought back on target with the approved budget and cash flow.d. M & V costs: The ISSUER assumes the financial responsibility for M & V costs directly or through the Contractor. Explain the relationship between M&V cost and savings accuracy calculations.e. Delays: Both the Contractor and the ISSUER may cause delays. Failure to implement a viable project in a timely manner costs the ISSUER in the form of lost savings, and can add cost to the project (e.g. construction interest, re-mobilization). Clarify schedule and how delays will be handled.f. Major changes in facility: Major changes in facility use, including closure may occur during the term of the contract. Clarify responsibilities in the event of a premature facility closure, loss of funding, or other major change.2. Operationala. Operating hours: The ISSUER generally has control over operating hours. Increases and decreases in operating hours can show up as increases or decreases in “savings” depending on the M&V method (e.g., operating hours multiplied by improved efficiency of equipment vs. whole-building/utility bill analysis). Clarify whether operating hours are to be measured or stipulated and what the impact will be if they change. If the operating hours are stipulated, the baseline should be carefully documented and agreed to by both parties.b. Load: Equipment loads can change over time. The ISSUER generally has control over hours of operation, conditioned floor area, intensity of use (e.g. changes in occupancy or level of automation). Changes in load can show up as increases or decreases in “savings” depending on the M & V method. Clarify whether equipment loads are to be measured or stipulated and what the impact will be if they change. If the equipment loads are stipulated, the baseline should be carefully documented and agreed to by both parties.c. Weather: A number of energy efficiency measures are affected by weather. Neither the Contractor nor the ISSUER has control over the weather. Changes in weather can increase or decrease “savings” depending on the M&V method (e.g. equipment run hours multiplied by efficiency improvement vs. whole-building/utility bill analysis). If weather is “normalized,” actual savings could be less than payments for a given year, but will average out over the long run. Clearly specify how weather corrections will be performed.d. User participation: Many energy conservation measures require user participation to generate savings (e.g., control settings). The savings can be variable and the Contractor may be unwilling to invest in these measures. Clarify what degree of user participation is needed and utilize monitoring and training to mitigate risk. If performance is stipulated, document and review assumptions carefully and consider M&V to confirm the capacity to save (e.g., confirm that the controls are functioning properly).3. Performancea. Equipment performance: Generally the Contractor is responsible for proper installation, commissioning, and performance of equipment. Generally the Contractor has responsibility to demonstrate that the new improvements meet expected performance levels including specified equipment capacity, standards of service, and efficiency. Clarify who is responsible for initial and long-term performance, how it will be verified, and what will be done if performance does not meet expectations.b. Operations: Responsibility for operations is negotiable, and it can impact performance. Clarify responsibility for operations, the implications of equipment control, how changes in operating procedures will be handled, and how proper operations will be assured.c. Preventive Maintenance: Responsibility for maintenance is negotiable, and it can impact performance. Clarify how long-term preventive maintenance will be assured, especially if the party responsible for long-term performance is not responsible for maintenance (e.g., Contractor provides maintenance checklist and reporting frequency). Clarify who is responsible for long-term preventive maintenance to maintain operational performance throughout the Contract term. Clarify what will be done if inadequate preventive maintenance impacts performance.d. Equipment Repair and Replacement: Responsibility for repair and replacement of Contractor-installed equipment is negotiable; however it is often tied to project performance. Clarify who is responsible for replacement of failed components or equipment throughout the term of the Contract. Specifically address potential impacts on performance due to equipment failure. Specify expected equipment life and warranties for all installed equipment. Discuss replacement responsibility when equipment life is shorter than the term of the Contract.Section 18: Utilize section 18 in proposal to place attachments: A, B and C.Instructions:Only measures documented in Part 4 Section 5.1 may be included in the attachmentsAll measures included in Part 4 Section 5.1 must be included in the attachmentsThe time allowed for preparation of the attachments shall be negotiated based on the scope of work presented in Part 4 Section 5.1The terms negotiated within the attachments shall form the basis for the IGA and final project pricingThe cost and availability of all equipment, materials, and supplies associated with the performing of the services described herein have been determined and included in the proposed cost.All labor costs, direct and indirect, have been determined and included in the proposed cost.PROPOSAL SIGNATURE PAGE (this page should be the first page of the proposal)By submitting this proposal, the Applicant certifies the following:This proposal is signed by an authorized representative of the firm.It can obtain the bonds and insurance certificates as required.The Applicant has attended the mandatory Pre-Proposal Meeting and is aware of prevailing conditions associated with performing these services.The potential ESCO has read and understands the conditions set forth in this RFP and agrees to them with no exceptions.The applicant has read, understands, and response complies with all revisions.All information provided in this application has been gathered based on diligent inquiry and is true, accurate, and complete in all respects, and does not contain any material misstatement of fact or omit to state a material fact or any fact necessary to make the statements contained herein not materially misleading, to its best knowledge and belief.Therefore, in compliance with this Request for Proposals, and subject to all conditions set forth herein, the undersigned offers and agrees.ESCO: ______________________________________________________________________ADDRESS: ___________________________________________________________________CITY, STATE, ZIP: _____________________________________________________________TELEPHONE NUMBER: ______________________________ FAX: _____________________FEDERAL EMPLOYER INDENTIFICATION NUMBER: ________________________________E-MAIL: ______________________________________________________________________Principal Place of Business if different from above:_____________________________________________________________________________Will any of the work under this contract be performed outside of the United States? YesNo (If yes, describe in Part 4.2 Section 5.3)BY: __________________________ TITLE: ______________________ DATE: _____________________________________________________ (Signature)__________________________________________ (Typed or printed name) ATTACHMENT A Preliminary ECM Cost / Annual Savings MatrixECM DescriptionBldg. 1 IDBldg. 2 IDBldg. 3 IDTOTALSCostSavingsCostSavingsCostSavingsCostSavingsLighting25,0005,00055,00012,00015,0003,500SUMSUMLighting controls49,0007,000 0 022,0006,000SUMSUMAHU VFDsTOTALSSUMSUMValues in dollars = ECM included in projectCell Blank = ECM not included for that buildingNote: The purpose of this Matrix is to summarize the project by ECM by building. The above is a sample. Please add columns and rows as necessary to include all buildings and measures addressed in Part 5. The “8 ? x 11" sheet size does not apply to this Attachment.As in Part 4 Section 5; the Cost includes: Labor Costs, Subcontractor Costs, Cost of Materials and Equipment and Related Items. It does NOT include ESCO overhead, mark-up, or profit. The sum of all costs shall equal the Estimated Project Cost in Attachment B.Electronic copy should be in EXCEL spreadsheet form.Enter zero amount for ECM’s not performed. To be completed only at the request of the ISSUER after all written responses have been evaluated and rankedATTACHMENT BESCO’s Preliminary Cost Proposal (see form next page)Attachment B is available in Excel format.To be completed only at the request of the ISSUER after all written responses have been evaluated and rankedATTACHMENT CESCO's PRELIMINARY ANNUAL CASH FLOW ANALYSIS USING ESCO’S PROPOSED INTEREST RATEFinanced Amount: __________Escalation Rate by Utility/FuelFinance Term: __________Electric: 0.0% Annual Interest Rate: __________Natural Gas: 0.0% Construction Months __________Steam: 0.0% Annual Payment __________Water: 0.0% Principal __________other (specify): 0.0% Interest __________ Escalation Rate for Annual Fees: 0.0% Yr.CalculatedElectric Dollar SavingsCalculatedNatural Gas Dollar SavingsOther Calculatedpurchased fuel Dollar SavingsCalculatedWater Dollar SavingsOther Please SpecifyCalculatedOperational Dollar SavingsTotal CalculatedDollar SavingsGuaranteed Dollar Savings( a )Annual Service Fees( b )Financing Cost(P&I)( c )Net Savings= a-b-c12345To be completed only at the request of the ISSUER after all written responses have been evaluated and ranked678TotalNOTES:Net savings must never be negative.A surplus in one year cannot be carried forward to create positive cash flow in a subsequent year.Electronic copy should be in EXCEL spreadsheet form. See page 24.APPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.eduAddress of Building or Complex: 1240 E Market St, Smithfield NC 27577Building Name: _Arboretum___Total Floors: _1___Building Age: __16__ - Built in: __2001__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __2,300__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__ Electric Meter for Building: Meter # 59591197 Acct # 14000460Gas Meter for Building: Meter # N278407. Acct # 2131302001Water Meter for Building: Meter # 60507008j (Reclaimed) Acct # 14000460 Meter # 72644572 Acct # 14000460Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 347 College Rd, Smithfield, NC 27577Building Name: _Health Addition___Total Floors: _2___Building Age: __8__ - Built in: __2009__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __23,362__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__ Electric Meter for Building: Meter # 1905588 Acct # 14000759Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 79671803 Acct # 14000759Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 325 College Rd, Smithfield, NC 27577Building Name: HealthTotal Floors: _2___Building Age: __19__ - Built in: __1998__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __38,984__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Varies__Electric Meter for Building: Meter # 1905588 Acct # 14000759Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 1516689 Acct # 14000751Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesRe-CommissioningInterior and exterior LED lightingVAV controllers upgradedPneumatic actuators upgradedChillerBoilerHot and Chilled water valves replacedWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 371 College Rd, Smithfield, NC 27577Building Name: Learning Resource CenterTotal Floors: __2__Building Age: __6__ - Built in: __2011__– Addition: - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom, Library) Building Total Square Footage: __31,835__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 7:30 AM-8 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Closed__Electric Meter for Building: Meter # 41110327 Acct # 14000740Gas Meter for Building: Meter # 830018 Acct # 9002058270003Water Meter for Building: Meter # 99999999j (Reclaimed water) Acct # 14000740 Meter # 72285383 Acct # 14000740 Steam Meter for Building: Chilled Water Meter for Building: Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstanceInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 111 College Rd, Smithfield, NC 27577Building Name: ElseeTotal Floors: _1___Building Age: __39__ - Built in: __1978__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __20,759__sq. ft.Additions/Renovations: ____Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14631437X Acct # 14000700Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 66058415 Acct # 14000701Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesAHU 3 does not economize2 AHU’s are originalPneumatic actuators upgradedHot and Chilled water valves replacedRe-CommissioningInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133Email: mtmassey@johnstoncc.edu Address of Building or Complex: 301 Jaguar Drive, Smithfield, NC 27577Building Name: SteamTotal Floors: _1___Building Age: __30__ - Built in: __1987__ – Addition: _____ - Age: _________Number of Buildings: __1__Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __29,340_sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14631437X Acct # 14000700Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 58960544 Acct # 14000701Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesRe-CommissioningBoilers and ChillersInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptions APPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 245 College Rd, Smithfield, NC 27577Building Name: WilsonTotal Floors: __2__Building Age: __41__ - Built in: __1976__ – Addition: _1985__ - Age: __32___Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom, Cosmetology, Administration, Student Center) Building Total Square Footage: __64,364__sq. ft.Additions/Renovations: Student CenterDescribe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14631437X Acct # 14000700Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 86058415 Acct # 14000701Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesRe-CommissioningInterior and exterior LED lightingAir Handlers – OriginalPneumatic Actuators upgradedHot and Chilled water valves replacedBoiler and ChillerCosmetology Window UnitsWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptions APPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 245 College Rd, Smithfield, NC 27577Building Name: Wilson AdditionTotal Floors: _2___Building Age: __11__ - Built in: __2006__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom, Administration) Building Total Square Footage: __28,075__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14631437X Acct # 14000700Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 64739454 Acct # 14000611Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 475 College Rd, Smithfield, NC 27577Building Name: Transport TechnologyTotal Floors: _1___Building Age: _35___ - Built in: _1982___ – Addition: _____ - Age: _________Number of Buildings: Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom, Shop) Building Total Square Footage: __16,829__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Varies__Electric Meter for Building: Meter # 16671015 Acct # 14000780Gas Meter for Building: Acct # 87282299Water Meter for Building: Meter # 66058411 Acct # 14000780Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesRe-CommissioningShop – LP HeatInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptions APPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133Email: mtmassey@johnstoncc.edu Address of Building or Complex: 479 College, Smithfield, NC 27577Building Name: BrittTotal Floors: __1__Building Age: __13_ - Built in: __2004__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Classroom, Office) Building Total Square Footage: __28,614__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Varies__Electric Meter for Building: Meter # 23731190 Acct # 14000765Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 62420698 Acct # 14000765Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesRe-CommissioningInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael MasseyTitle: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133Email: mtmassey@johnstoncc.edu Address of Building or Complex: 543 College Rd, Smithfield, NC 27577Building Name: Public SafetyTotal Floors: _1___Building Age: __9___ - Built in: __2008__ – Addition: _____ - Age: _________Number of Buildings: Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __27,485__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: Varies / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 28893393 Acct # 14000772 Meter # 82665242 Acct # 14000790 Acct # 14000773 (Area Lights)Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 70114443j (Reclaimed water) Acct # 14000772 Meter # 68296683 Acct # 14000772Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lighting Work to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptions APPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.eduAddress of Building or Complex: 377 College Rd, Smithfield, NC 27577Building Name: SmithTotal Floors: __1__Building Age: __15___ - Built in: __2002__ – Addition: _____ - Age: _________Number of Buildings: ___Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom, Gym) Building Total Square Footage: __31,835__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__ Electric Meter for Building: Meter # 1905588 Acct # 14000759Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 79671803 Acct # 14000759Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesRe-CommissioningChillerBoilerInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 135 Bestwood Dr, Clayton, NC 27520Building Name: Workforce Development CenterTotal Floors: _2__Building Age: __12__ - Built in: __2005__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __31,947__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # TP4786 Acct # 509 821 7804Gas Meter for Building: Meter # 647253 Acct # 2131302002Water Meter for Building: Meter # 70142320 Acct # 33554Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133Email: mtmassey@johnstoncc.edu Address of Building or Complex: 9046 Cleveland Rd, Clayton, NC 27520Building Name: ClevelandTotal Floors: __1__Building Age: __21__ - Built in: __1996__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __7826__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 8 AM-10 PM / Fr 8 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # TP1397 Acct # 034 802 4332; Area Lights: Acct # 036 888 8335Gas Meter for Building: Water Meter for Building: Meter # 32068160 Acct # 1629Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptions APPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 243 Jaguar Drive, Smithfield, NC 27577Building Name: SandersTotal Floors: __1__Building Age: __22__ - Built in: __1995__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Maintenance Shop, Breakroom, Storage) Building Total Square Footage: __13,500__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: M-Th 7 AM-5 PM / Fr 7 AM-3 PM / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14631437X Acct # 14000700Gas Meter for Building: Meter # NEC2157 Acct # 9002058270001Water Meter for Building: Meter # 58960544 Acct # 14000701Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: Devil’s Racetrack Rd, Four Oaks, NC 27524Building Name: Howell Woods Caretaker HouseTotal Floors: __2__Building Age: __67__ - Built in: __1950__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Housing) Building Total Square Footage: __1780__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __ Daily: Varies / Weekend: Sat-Sun Varies __Electric Meter for Building: Meter # 14037996 Acct # 258215Gas Meter for Building: Water Meter for Building: Meter # 94448199 Acct # 10999Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 6601 Devils Racetrack Rd, Four Oaks, NC 27524Building Name: Howell Woods Environmental Learning CenterTotal Floors: _1___Building Age: __19__ - Built in: __1998__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __3,375__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: Varies / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14037955 Acct # 530079500001Gas Meter for Building: Acct # 87266740Water Meter for Building: Meter # 60409212 Acct # 6475Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingWork to be completed during nighttime hours and/or on weekendsWork area to be restored to college’s standard for faculty/staff/student useNo class disruptionsAPPENDIX IFACILITIES TO BE ANALYZEDEach building to be included in the project shall be identified and described in the following form.Date: 9/19/2017Name of Agency or University: Johnston Community CollegeDivision: Department: Contact Person: Michael Massey Title: Facilities DirectorPhone: 919-209-2087Fax: 919-209-2133 Email: mtmassey@johnstoncc.edu Address of Building or Complex: 6601 Devils Racetrack Rd, Four Oaks, NC 27524Building Name: Howell Woods ShopTotal Floors: __1__Building Age: __52__ - Built in: __1965__ – Addition: _____ - Age: _________Number of Buildings: ____Building Operator: _______________Phone: Building Engineer: _______________Phone: Building Manager: _______________Phone: Building Type: (Office, Classroom) Building Total Square Footage: __3,168__sq. ft.Additions/Renovations: Describe Renovations: Operating Schedule: __Daily: Varies / Weekend: Sat-Sun Varies__Electric Meter for Building: Meter # 14710052 Acct # 530083600002Gas Meter for Building: Acct # 87266740Water Meter for Building: Acct # 19256Steam Meter for Building: Chilled Water Meter for Building:Issues to be Addressed by Performance ContractHVAC SystemsLighting SystemsWater SystemsSpecial Needs or CircumstancesInterior and exterior LED lightingAPPENDIX IIAPPENDIX IIIINSURANCE:COVERAGE - During the term of the Contract, the Vendor at its sole cost and expense shall provide commercial insurance of such type and with such terms and limits as may be reasonably associated with the Contract. As a minimum, the Vendor shall provide and maintain the following coverage and limits:a. Worker’s Compensation - The Vendor shall provide and maintain Worker’s Compensation Insurance, as required by the laws of North Carolina, as well as employer’s liability coverage with minimum limits of $500,000.00, covering all of Vendor’s employees who are engaged in any work under the Contract. If any work is subcontracted, the Vendor shall require the sub-Contractor to provide the same coverage for any of his employees engaged in any work under the Contract.b. Commercial General Liability - General Liability Coverage on a Comprehensive Broad Form on an occurrence basis in the minimum amount of $500,000.00 Combined Single Limit. (Defense cost shall be in excess of the limit of liability.)c. Automobile - Automobile Liability Insurance, to include liability coverage, covering all owned, hired and nonowned vehicles, used in connection with the Contract. The minimum combined single limit shall be $250,000.00 bodily injury and property damage; $250,000.00 uninsured/under insured motorist; and $2,500.00 medical payment.REQUIREMENTS - Providing and maintaining adequate insurance coverage is a material obligation of the Vendor and is of the essence of this Contract. All such insurance shall meet all laws of the State of North Carolina. Such insurance coverage shall be obtained from companies that are authorized to provide such coverage and that are authorized by the Commissioner of Insurance to do business in North Carolina. The Vendor shall at all times comply with the terms of such insurance policies, and all requirements of the insurer under any such insurance policies, except as they may conflict with existing North Carolina laws or this Contract. The limits of coverage under each insurance policy maintained by the Vendor shall not be interpreted as limiting the Vendor’s liability and obligations under the Contract.17. GENERAL INDEMNITY: The Vendor shall hold and save the State, its officers, agents, and employees, harmless from liability of any kind, including all claims and losses accruing or resulting to any other person, firm, or corporation furnishing or supplying work, services, materials, or supplies in connection with the performance of this Contract, and from any and all claims and losses accruing or resulting to any person, firm, or corporation that may be injured or damaged by the Vendor in the performance of this Contract and that are attributable to thenegligence or intentionally tortious acts of the Vendor provided that the Vendor is notified in writing within 30 days that the State has knowledge of such claims. The Vendor represents and warrants that it shall make no claim of any kind or nature against the State’s agents who are involved in the delivery or processing of Vendor goods to the State. The representation and warranty in the preceding sentence shall survive the termination or expiration of thisContract. ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
Related searches
- north carolina school performance grades
- request for proposal template microsoft word
- north carolina schools report card
- north carolina schools report cards
- north carolina state treasurer s office
- north carolina state report card
- north carolina unclaimed money list
- unclaimed money north carolina list of names
- north carolina alternative teaching programs
- north carolina cna reciprocity form
- north carolina health systems
- north carolina health exchange