Catalyst 3560 Switch Hardware Installation Guide - Cisco
Catalyst 3560 Switch
Hardware Installation Guide
March 2010
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-6337-07
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR
LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco¡¯s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco¡¯s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
? Turn the television or radio antenna until the interference stops.
? Move the equipment to one side or the other of the television or radio.
? Move the equipment farther away from the television or radio.
? Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB¡¯s public
domain version of the UNIX operating system. All rights reserved. Copyright ? 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED ¡°AS IS¡± WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE,
OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCDE, CCENT, CCSI, Cisco Eos, Cisco Explorer, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase,
Cisco StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco TrustSec, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip
Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work,
Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and
Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the
Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,
Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the
IronPort logo, Laser Link, LightStream, Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY,
PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are
registered trademarks of Cisco and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (1002R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Catalyst 3560 Switch Hardware Installation Guide
? 2004¨C2010 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
vii
Audience
Purpose
i-vii
i-vii
Conventions
i-vii
Related Publications
i-viii
Obtaining Documentation and Submitting a Service Request
CHAPTER
1
Product Overview
1-1
Setting Up the Switch
Features
i-ix
1-1
1-1
Front Panel Description 1-3
Fast Ethernet Switch Front Panel Descriptions 1-3
Gigabit Ethernet Switch Front Panel Descriptions 1-6
10/100 and 10/100/1000 Ports 1-8
PoE Ports 1-9
SFP Module Slots 1-10
SFP Modules 1-10
SFP Module Patch Cable 1-10
Dual-Purpose Port 1-10
LEDs 1-11
System LED
1-11
RPS LED 1-12
Port LEDs and Modes 1-13
Dual-Purpose Port LEDs 1-15
Cable Guard 1-15
Rear Panel Description 1-15
Internal Power Supply 1-18
DC Power Connector 1-18
Cisco RPS 1-19
Cisco RPS 2300 1-19
Cisco RPS 675 1-19
Console Port 1-19
Security Slots 1-20
Management Options
1-20
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
iii
Contents
Network Configurations
CHAPTER
2
1-21
Switch Installation (24- and 48-Port Switches)
2-1
Preparing for Installation 2-1
Warnings 2-2
Installation Guidelines 2-5
Box Contents 2-6
Tools and Equipment 2-6
Verifying Switch Operation 2-6
Powering Off the Switch 2-7
Installing the Switch 2-7
Rack-Mounting 2-7
Removing Screws from the Switch 2-8
Attaching Brackets to the Catalyst 3560 Switch 2-8
Mounting the Switch in a Rack 2-10
Attaching the Cable Guide 2-11
Wall-Mounting 2-12
Attaching the Brackets to the Switch for Wall Mounting
Attaching the RPS Connector Cover 2-13
Mounting the Switch on a Wall 2-14
Table- or Shelf- Mounting 2-15
2-12
Installing and Removing SFP Modules 2-15
Installing SFP Modules into SFP Module Slots 2-16
Removing SFP Modules from SFP Module Slots 2-17
Inserting and Removing the SFP Module Patch Cable
10/100 or 10/100/1000 Ports
2-19
Connecting the Switch to Compatible Devices 2-20
Connecting to 10BASE-T or 100BASE-TX Devices
Connecting to Fiber-Optic SFP Modules 2-21
Connecting to 1000BASE-T SFP Modules 2-22
Connecting to a Dual-Purpose Port 2-23
Where to Go Next
CHAPTER
3
2-18
2-20
2-24
Switch Installation (8- and 12-Port Switches)
3-1
Preparing for Installation 3-1
Warnings 3-2
Installation Guidelines 3-5
Equipment That You Supply 3-6
Catalyst 3560 Switch Hardware Installation Guide
iv
OL-6337-07
Contents
Box Contents 3-7
Tools and Equipment
3-7
Verifying Switch Operation 3-7
Powering Off the Switch 3-7
Installing the Switch 3-7
Desk or Shelf Mounting 3-8
Desk or Shelf Mounting (Unsecured) 3-8
Desk or Shelf Mounting (Secured) 3-8
Under the Desk or Shelf Mounting 3-9
Wall-Mounting (with Mounting Screws) 3-12
Magnet Mounting 3-15
Rack-Mounting 3-16
Attaching Brackets to the Switch 3-16
Mounting the Switch in a 19-Inch Rack 3-17
Wall-Mounting (with Rack-Mount Brackets) 3-17
Securing the AC Power Cord 3-19
Where to Go Next
CHAPTER
4
Troubleshooting
3-20
4-1
Diagnosing Problems 4-1
Evaluate Switch POST Results 4-2
Monitor Switch LEDs 4-2
Verify Switch Connections 4-2
Bad or Damaged Cable 4-2
Ethernet and Fiber Cables 4-3
Link Status 4-3
Transceiver Module Port Issues 4-3
Port and Interface Settings 4-4
Ping the End Device 4-4
Spanning Tree Loops 4-4
Monitor Switch Performance 4-4
Speed, Duplex, and Autonegotiation 4-4
Autonegotiation and Network Interface Cards
Cabling Distance 4-5
Clearing the Switch IP Address and Configuration
Locating the Switch Serial Number
4-5
4-5
4-6
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
v
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- cisco catalyst 2960 c and 3560 c series compact switches
- cisco catalyst 3560 series switches barcodesinc
- cisco catalyst 3560 series switches vantage labs
- cisco switch catalyst 3650 series data sheet
- cisco catalyst 3560 e series switches
- catalyst 3560 switch hardware installation guide cisco
- cisco catalyst 3560 cx and 2960 cx series switches faq
- cisco catalyst 3560 series switches data sheet
- catalyst 3560 switch getting started guide cisco
Related searches
- cisco catalyst 2960 switch configuration
- electrical installation guide pdf
- oracle 19c installation guide windows
- cisco catalyst 2960 configuration guide
- cisco catalyst 2960 setup
- cisco catalyst 2960 user manual
- cisco catalyst 2960s manual
- cisco catalyst 2960 manual
- cisco catalyst 2960 x manual
- cisco catalyst 2960 poe
- program cisco catalyst 2960 switch
- cisco catalyst 2960 specs