Honors Chemistry
Chapter 2 problem set:
Page 42 Section Review # 3, 5
Page 57 Section Review # 2, 5, 7
Page 59-61 Chapter Review # 15, 16, 18, 19, 22, 24, 25, 29, 35, 36, 38, 49, 51
2.1 Scientific Method (see text)
2.2 Units of Measurement
Measurement – _______________________________________________________________________
The problem is, what do you use as a standard?
Standard should be an ___________________________________________________________________________________________________________________________________________________________.
The SI System
Important base units to know:
|Quantity |Unit |Abbreviation |
|Mass |kilogram | |
|Length |meter | |
|Time |second | |
|Temperature |kelvin | |
|Amount of substance |mole | |
|Electric current |ampere | |
Important prefixes(multiples of base units) to know:
|Prefix |Abbreviation |Meaning |Example |
|mega- |M |106 | |
|kilo- |k |103 | |
|deci- |d |10-1 | |
|centi- |c |10-2 | |
|milli- |m |10-3 | |
|micro- |u |10-6 | |
|nano- |n |10-9 | |
|pico- |p |10-12 | |
Factor Label Method (Dimensional Analysis)
A method of problem solving that treats units like algebraic factors
Rules
1. Put the known quantity over the number 1.
2. On the bottom of the next term, put the unit on top of the previous term.
3. On top of the current term put a unit that you are trying to get to.
4. On the top and bottom of the current term, put in numbers in order to create equality.
5. If the unit on top is the unit of your final answer, multiply/divide and cancel units. If not, return to step # 2.
6. As far as sig figs are concerned, end with what you start with!
Example: convert 3.0 ft to inches
Example: convert 1.8 years to seconds
Example: convert 2.50 ft to cm if 1 inch = 2.54 cm
Example: convert 75 cm to m
Example: convert 150 g to kg
Example: convert 0.75 L to cm3
.
Example: convert 22 cm to dm
Density – ratio of mass to volume
The common density units are:
•
•
•
Formula is _________________________________
Density is a) b) c)
Two ways to find volume in density problems:
1. 2.
Note: the density is the same no matter what is the size or shape of the sample.
Ex1: Find the density of an object with m= 10g and v=2 cm3
Ex2: A cube of lead 3.00 cm on a side has a mass of 305.0 g. What is the density of lead?
First, calculate it’s volume:
Next, calculate the density:
2.3 Using Scientific Measurement
Precision vs. Accuracy
|Precision |Accuracy |
| | |
| | |
|_____________________________ |[pic] |______________________________ |
| | | |
| | | |
| | | |
|_____________________________ | |______________________________ |
Percent Error - experiments don’t always give true results - error is pretty much a given
Observed value (experimental value) - data found in an ____________________
True value (accepted value, theoretical value) - data that is generally accepted as true
Percent (%) error = (order is important as it implies direction)
+/- shows show the direction of the error - values are either too high or too low
Note: Percent error is a positive number when the experimental value is too high and is a negative number when the experimental value is too low.
Ex1: 66 Co is the answer in your experiment 65 CO is the theoretical value
Uncertainty in Measurement
• Two important points:
1. ______________________________________________________________________________
2. ______________________________________________________________________________
• Example – your chemistry’s teacher’s height is 5’4” not 5.43234566333333 inches
• When making a measurement, include all readable digits and 1 estimated digit
o always read between the lines!
o the digit read between the lines is always uncertain
|[pic] |if the measurement is exactly half way between lines record it as 0.5 |
| |if it is a little over, record ___________________ |
| |if it is a little under, record __________________ |
| |You would read this as 18.0 mL and not 18.5 mL. |
Significant Figures (Digits) - “Sig Figs”
• Definition: _____________________________________________________________________
• 1.15 ml implies 1.15 + 0.01 ml
• The more significant digits, the more reproducible the measurement is.
These are the numbers that “count!”
Ex1: π = 22/7 = 3.1415927 what do math teachers let you use?
Ex2: You collect a paycheck for a 40 hour week – what’s the difference between getting paid pi vs. 3.14 ?
Rules for finding the # of sig figs
1. All non-zeros are significant ex. 7 [ ] 77 [ ] 4568 [ ]
2. Zeros between non-zeros are significant ex. 707 [ ] 7053 [ ] 7.053 [ ]
3. Zeroes to the left of the first nonzero digit fix the position of the decimal point and are not significant
ex: 0.0056 [ ] 0.0789 [ ] 0.0000001 [ ]
4. In a number with digits to the right of a decimal point, zeroes to the right of the last nonzero digit are significant
ex: 43 [ ] 43.00 [ ] 43.0 [ ] 0.00200 [ ] 0.040050 [ ]
5. In a number that has no decimal point, and that ends in zeroes (ex. 3600), the zeroes at the end may or may not be significant (it is ambiguous). To avoid ambiguity, express in scientific notation and show in the coefficient the number of significant digits. ex. 3600 = 3.6 x 103 [ ]
Counting significant digits
• 1. __________________________________________________________
• 2. __________________________________________________________
Ex1: 700 [ ] - means “about 700 people at a football game”
700. [ ] - means “exactly 700 ......”
700.0 [ ] - means “teacher weighs exactly 700.0 lbs”
Other examples 0.5 [ ] 0.50 [ ] 0.050 [ ]
Sig. figs apply to scientific notation as well
9.7 x 10 2 = 970 [ ] 1.20 x 10 -4 = .000120 [ ]
Calculating with Measurements ( Sig Fig Math )
Rounding Rules
XY ---------------------> Y
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________
_____________________________________________
Ex1: round to 3 sig figs 35.27 =
87.24 =
95.25 =
95.15 =
Note - the “5” rule only applies to a “dead even” 5 - if any digit other than 0 follows a 5 to be rounded, then the number gets rounded up without regard to the previous digit.
Ex2: round to 3 sig figs 35.250000000000000000000000001 =
Calculating rules:
1. Multiplying or dividing – round results to the smaller # of sig. figs in the original problem.
Ex1: 3.10 cm Ex2: 7.9312 g
4.102 cm / 0.98 m
x 8.13124 cm
2. Adding or subtracting - round to the last common decimal place on the right.
Ex1: 21.52 Ex2: 73.01234 g
+ 3.1? - 73.014?? g
Note - exact conversion factors do not limit the # of sig figs - the final answer should always end with the # of sig figs that started the problem
ex. convert 7866 cm to m
2.4 Solving Quantitative Problems
1. Analyze – read carefully, list data with units, draw a picture
2. Plan – list conversion factors, show that units will work
3. Compute – use a calculator and use significant figures
4. Evaluate – does the answer “seem right” ?
Proportional relationships
Directly proportional – examples – density (mass of water vs. volume of water), grades vs. freedom
[pic]
In this example, we would say that, “volume of water is directly proportional to mass of water.” We can write it as __________________________
Inversely proportional – examples – speed vs. time, more accidents = less driving
Another chemistry example, as the pressure of a gas increases, the volume decresases:
|Volume of |[pic] |
|gas (mL) | |
|Pressure | |
|of gas (atm) | |
| | |
|25.2 | |
|0.971 | |
| | |
|28.3 | |
|0.865 | |
| | |
|32.4 | |
|0.755 | |
| | |
|39.6 | |
|0.618 | |
| | |
|43.1 | |
|0.568 | |
| | |
|47.8 | |
|0.512 | |
| | |
|52.6 | |
|0.465 | |
| | |
When two variables are related this way, they are said to be inversely proportional.
We can write it as __________________________
2.2 – Heat and Temperature – there is a difference
Compare heat and temperature of a thimbleful of water vs. a bathtub.
Heat is the amount of energy a chemical has –measure it in joules (J). Because we can’t directly measure heat, we have to measure “temperature”, which reflects how much kinetic energy an object has – measure it in °C or Kelvins). In thermodynamics, the term “enthalpy” is used interchangeably with “heat”, as it avoids confusion between the terms “heat” and “temperature”.
Heat vs. Temperature
Temperature – a measure of the average kinetic energy of the particles
Heat – the sum of the total energy of the particles
Temperature scales
Thermometer – works by thermal expansion, usually Hg or alcohol
Celsius - devised by a Swedish astronomer - Anders Celsius - 1742
Kelvin - named for Lord Kelvin - English physicist
Absolute zero - temperature at which all molecular motion stops - never been reached, temperature = 0 K or -273.15 oC
Conversion formulas:
Conversion formulas:
K =
oF =
oC =
Examples:
Ex1 Convert 100.0 oC to K
Ex2 Convert 293.0 K to oC
Ex3 Convert 90.0 oF to oC
Ex4 Convert 20.0 oC to oF
Heat transfers between objects – flows from hot to cold - Law of Conservation of Energy
Ex1:ice cube in a thermos of hot water - ice melts, water cools - same amount of heat
SI unit of heat - Joule (J) calorie is also used frequently
Calorie - the amount of energy required to raise the temperature of 1 g of water by 1 oC
(Calories – capital letter – really means kilocalories – used in food energy measurement)
1.000 calorie = 4.184 Joules
Heat Capacity vs. Specific Heat
Amount of heat needed to change the temperature of an object depends on:
a) b) c)
Heat capacity - amount of heat needed to raise the temperature of a sample – depends on mass – we need something more specific, so…..
Ex, which would you rather use to pull a pan from a hot oven, an oven mitt or a sheet of aluminum foil? The aluminum foil will transmit the heat easily while the oven mitt is a much better insulator. The reason: Oven mitts have a higher heat capacity than aluminum.
Specific Heat ( Cp ) - the amount of energy required to raise the temperature of 1 g of substance by 1 Co
q = heat (J or cal)
Cp = specific heat (J / g ▪ °C) or (cal / g ▪ °C)
m = mass(g)
Δt = change in temperature (°C or K)
so.... Cp = 1.000 cal/g oC or 4.184 J/g oC for water
Different materials have different specific heats
|material at 298 K and 1 atm |Cp specific heat (J/g K) |
|ice |2.09 |
|water |4.18 |
|steam |1.86 |
|sodium |1.23 |
|aluminum |0.9 |
|iron |0.45 |
Computing heat to determine how much heat is required to heat a material
It takes energy to make the temperature of anything increase. The relationship between energy and temperature is shown by the equation:
Specific Heat Problems
For water, Cp = 1.000 cal/g oC or 4.184 J/g oC for water
Ex1: How many calories does it take to heat 20. g of water from 10.0 to 40.0 oC? Also how many J?
Ex2: How much heat is required to heat 75 g of Iron (Cp = 0.444 J/gCo) from 15.5 to 57.0 oC?
Ex3: What is the specific heat of an object if 250 calories will heat 55 g of it from 25.0 to 100.0 oC?
Ex4: - If a 100.0 g sample of silver (Cp = .237 J/g oC) at 80.0 Co loses 50. calories, what will its final temperature be?
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- honors biology photosynthesis quiz
- honors biology photosynthesis test
- honors biology study guide answers
- national honors society
- honors biology textbook pdf
- 9th grade honors biology book
- honors grade point average calculator
- honors biology worksheets
- honors biology 9th grade pdf
- honors biology textbook 9th grade
- honors college application essay examples
- national honors society essay example