Determining Port Velocity - EFI Dyno Tuning LC
Determining Port Velocity and Volume
Determining air velocity is a useful part of testing. It is calculated as follows:
V = 1096.7* √¯H/d
Where:
V= Velocity in feet per minute
H= Pressure drop across test piece in inches of water (28” of water column being a standard)
d= density of air in pounds per cubic foot ( .075 pounds per cubic foot at standard conditions )
This represents the highest speed of the air in the flow path, at or near the section of minimum area (i.e. through the valve seat at low values of L/D, through the pushrod pinch, or minimum intake cross section, which ever is smaller).
Once velocity has been calculated, the volume can be calculated by multiplying the velocity by the minimum cross section area. Since we measure flow in cubic feet per minute, we use the first formula and divide by the cubic feet of cross section area: If we have an average cross section of 2.1 square inches:
Volume = Velocity (21,190 fpm) x Area (2.1 sqin x 1 sqft/144 sqin - converts sqin to sqft) = 309 cfm @ 28”
Since we use feet per second in the flow measurement of ports the formula above the equation becomes:
V = 1096.7/60 (18.278) * √¯H/d
V = 353 feet per second (fps)
This should be the highest velocity measured in a port flow tested at 28” of water column.
Mean Piston speed in linear ft/sec from stroke in inches & RPM (David Vizard)
We want to find the average speed of a piston traveling up or down between TDC and BDC. Though it should be emphasized the piston speed peaks much faster than the value we will find, and it slows to a stop and perhaps reverses slightly at TDC & BDC, this mean (average) velocity figure is highly useful as a comparator. It's also useful to note for later that because of the secondary-linkage effect of the connecting rod, the piston spends more time in the lower 180* of the rotation.
Conversion of measurement units: stroke in inches divided by 12 to get stroke in feet : s/12 = stroke in feet
then take the stroke times two because the piston travels
the stroke's distance twice in a revolution, and by convention we measure rotational speed by full revolutions : ( S/12 ) x 2 or,
by taking the 2 inside the brackets, we get ( S /6 )
Then, since by convention, we measure rotational speed in automotives in a per minute format,
and we use a per second format for gas velocity, we need the revolutions each second, i.e. per
one sixtieth of a minute ,
so : ( S/6 ) x RPM/60 or cleaning up the formula by basic algebra :
S/360 x rpm = average speed of a piston traveling up or down between TDC and BDC
Mean Gas speed from piston speed (above) and "area/cross section quotient":
We want to find the average gas velocity over a stroke of the piston- a half revolution of the crank, assuming we have the cross-sectional area of a header tube, or of an intake or exhaust port. The latter can be approximated by measuring centerline length and port volume, and subsequently converting the units of measure to match the units for the motor bore area, in this case, square inches.
There are several ways of accumulating the measurements required, but the simplest starts with bore area which we are likely able to calculate easily, either working from bore diameter (‘B’) taken down to radius, & squared & multiplied by Pi, or from engine total volume divided by stroke and number of cylinders.
So: ('B' area/ 'P' area), where p can stand for either pipe or port area in sqin.
So we now have an existing area relationship mathematically described. To use some examples, if the piston had 6 inches area and the header pipe 2, we would have a factor of 3... and a design error on our hands: practice has proven that the relationship on the exhaust side should be between approximately 4.5, for high RPM 4-stroke modern motorcycle engines and dedicated auto racing power plants, to as little as 9 for those of us working with older low-RPM-oriented production power plants, and between 4 and 8 on the intake side.
This relationship is far better described/defined by what we are working toward a calculation of: gas velocity at RPM.
Gas velocity at RPM
We can calculate that by combining the two formulas. When we had bore area calculated above and looked at its relationship to port area, we could envision the gas achieving some unknown- but already apparent to be high- velocity as it exited through the port, or arrived through the port. What we didn't include was quantification of the volume being transferred each cycle: how deep the piston traveled to reach BDC, or how many times per second did it come back to TDC?
Again, our first formula has linear information, which combined with area gives us volume, and it has rate. Thus:
( S/360 ) x RPM x ( B area / P area )
let’s try some examples:
We spoke of an imaginary engine having 4” pistons of 12.56 sqin and an exhaust header (1.50” pipe) 1 5/8” pipe of (1.484) 1.766 sqin ID (you could also evaluate the intake side by using intake runner size). The stroke is then calcuable to be 3.00", and we are doing calculations like this with power in mind, so let’s say that the RPM we wish to examine is 5,500rpm. The port area used was the header pipe area, but that's an extension of the port; we'll start ignoring the difference.
So, we have:
Exhaust
1.50” - (3.00/360) x 55000 x (12.56 / 1.484) = 388 ft/sec
1.50” - (2.75/360) x 55000 x (12.56 / 1.484) = 356 ft/sec
1.625” - (3.00/360) x 55000 x (12.56 / 1.766) = 328 ft/sec
1.625” - (2.75/360) x 5,5000 x (12.56 / 1.766) = 299 ft/sec
Intake
Stock HO intake - (3.00/360) x 55000 x (12.56 / 1.70) = 339 ft/sec
Stock HO intake - (2.75/360) x 55000 x (12.56 / 1.70) = 310 ft/sec
Ported HO intake - (3.00/360) x 55000 x (12.56 / 2.04) = 282 ft/sec
Ported HO intake - (2.75/360) x 55000 x (12.56 / 2.04) = 259 ft/sec
In practice rules of thumb developed say that at peak power, the ft/sec figure should be somewhere within 280-380 exh and 240-355 intake.
Let’s take another example- a 302 cid v8 with a 1.625 OD diameter header pipe and a relatively mild state of tune that leaves us interested in its 5,500 rpm statistics. It has a 4.000" bore (area=12.56 in2) and 3.00" stroke, and the ID of the header pipe is approx 1.5" ID pipe with wall thickness deducted for accurate calculation. So:
1.625” = (3.00 / 360) x 5500 x (12.56 / 1.77) = 325 ft/sec for 1.625” pipes
1.50” = (3.00 / 360) x 5500 x (12.56 / 1.484) = 388.7 ft/sec for 1.50” pipes
tmoss comment: The above assumes 100% stroke volume is usable, but that is affected by the IV close event and if it is beyond BDC, then 100% cylinder capture is not possible unless ram tuning is assumed correctly and adjusted for.
(2.75 / 360) x 5500 x (12.56 / 1.77) = 298 ft/sec for 1.625” pipes when effective stoke (IV valve close) is used.
(2.75 / 360) x 5500 x (12.56 / 1.484) = 356 ft/sec for 1.50” pipes when effective stoke (IV valve close) is used.
This result implies the motor is being revved right at its power peak for 1.5” pipes and/or that larger headers would likely give more power at this and any higher rpms. As always, a trade-off exists, as the 1.625" pipes will have produced a greater power up close to this rpm, and may make it unwise to take that power advantage which has "accumulated" as the motor rpm's have risen under load, and trade it off for greater peak power.
The next available tubing size up - 1 5/8 “ - is an 18-19% jump, putting the ft/sec figure @ 325 but progressively tending to be wrong as you look at increments of lower RPM.
So where does that leave us in picking a tube size? That figure is in square inches, so we divide by Pi, take the square root, multiply by two, & arrive at a dimension for ID. I add .049" x 2 for the walls to get the OD, and find it to be 1.50". We already figured using 1.50" OD for several inches coming off the ports and do the remainder in 1.625". Now we’re less worried that the 1.5 need to be mandrel-bent, though we know the disadvantage of 'crush bent' is less related to simple loss-of-area type restriction and more the energy used in speeding up and slowing down the gases as they pass through cross section changes. Since this area of pipe figure is notably smaller than the stock port area as measured at the opening, it confirms that the right track would be in filling the exhaust port floor.
Since it's becoming apparent that the variable we are most likely to want to solve for is the port area, we need to reformat our equation to solve for port cross-sectional area when we have all the other figures. This requires setting the formula up with an adjustable ft/sec position, because depending on the character of the motor's use you will have different aims.
Starting from:
( S/ 360 ) x RPM x ( B area / P area) = ft/sec
or,
writing it on one line, since we are fortunate that order of operations is irrelevant here
S / 360 x RPM x B area / P area = ft/sec
3.00 /360 x 5500 x 12.56/1.78 = 323 ft/sec
2.75 /360 x 5500 x 12.56/1.78 = 297 ft/sec for effective volume
It then holds that:
S/360 x RPM x B area / ft/sec = P area
Putting the formula to yet another use, you can measure the ports you have to see what RPM band they suit. Take soft wire, like solder, and measure the top length (beside guide) and bottom length, averaging them to get centerline length, then CC the port. You can now calculate average port cross section: take the CC's and divide out the length. Remember 16.39cc=1ci, convert the port volume into cubic inches before dividing by the length, assuming you used inches to measure centerline length. GT40P port = 4.8” CL & 140cc . 140/4.8 = 29.17 / 16.387 = 1.78 ci
The derivation of the formula I am providing for this requires you to find the reciprocal, but scientific calculators have that function
S / 360 x B area / (380 ft/sec x P area ) = 1/rpm = 6,462
2.75 / 360 x 12.56 /(297 ft/sec x 1.78) = 1/rpm = 5,510
So, some rules of thumb as far as desired gas velocities.
Highly developed ports such as those found in race specific castings can accept 10-20% higher velocities, due to the lack of flow differentials. In other words, they use the full port area, and to not have "hot spots": areas where the flow chooses to concentrate and which could become turbulent or supersonic if pushed beyond a certain speed. Also such engines are likely to have high compression which somewhat changes the dynamics of cylinder filling and emptying.
Figures shown are average velocity throughout the port, and references to effects are in the RPM range of peak horsepower.
240 ft/sec - intake - ram effect faint
- exhaust- scavenge faint
260 ft/sec - intake - ram effect moderate
- exhaust- scavenge weak to moderate
280 ft/sec - intake - substantial ram
- exhaust - scavenge moderate
300 ft/sec - intake - * ideal ram
- exhaust - substantial scavenge
320 ft/sec - intake - possible loss
- exhaust - * ideal scavenge
340 ft/sec - intake - likely loss
- exhaust - possible loss
Correcting Runner Length
Q: We have just got a sbc built and the engine builder had a blonde moment and has installed a sheet metal intake with way to large of runners on it. Needless to say the motor does not make the power we are looking for. My question would be if we are able to install a sort of insert and get the runner volume under control will we see a good gain in power even though the plenum volume is still large. It is a 366 SBC with Brodix canted valve heads 290cc 13.5 :1 comp. The total runner length is 12.4 "and needs to run at 6000 to 6500 steady WOT rpm. The runner volume right now is 600 cc and I figure that it should be about 300 cc.
A: With a 12.4" long intake tract (port and runner total length) you are tuned from 6800 to 8000rpm. This is well above your engines intended operational rpm range. This means your operating the engine at an RPM where the intake tract pressure pulse is either neutral or slightly negative. You may be neutral in this area so reversion might not to bad but it’s far from an optimum situation, now for the good news.
Depending on the manifold design you have, you can either increase air speed to band-aid the runner length or make spacers to put in the plenum to lengthen the runners. You really need .750 thousands to bring the manifold back into tune but that will take up a lot of plenum volume. If you’re out of tune the runner volume is secondary to air speed and wave tuning. I have done this many times and actually do it quite often. In many cases the results are astounding. Our 622 engine uses the Profiler 2/4 tunnel ram intake. This manifold is tuned from 7400rpm to 8700rpm. The larger engines all operate from 6000rpm to 7500rpm and some as high as 8000rpm. So the engine is trying to make peak TQ at 5500rpm and peak power at 7500rpm. Using this manifold causes a hole in the mid range of the power curve because it’s "out of tune" there. I fill the runners to increase air speed as much as possible without hurting top end power. The result is a 45ft/lbs increase in torque and a 60hp increase in power through the middle of the power curve. The engine accelerates much faster and recovers on the gear change better. If I where able to put plates in the plenum to increase runner length instead of increasing air speed the result would be even more power and a broader power curve because I would not only have the proper runner volume but the proper tuned length as well.
The course of action we take as well as the end result will depend on the manifold design you have to work with. Sometimes I can band-aid them and sometimes I can’t. If you have measurements and pictures of the manifold it would help a great deal. I can talk you through it if you want.
Darin Morgan
R&D-Cylinder Head Dept.
Reher-Morrison Racing Engines
Restricted Inlet Engines
Welcome to restricted engines. Take everything you know and put it on a table in front of you. You will only be able to use about ½ of it but it’s nice to review it quickly. Most restricted engines limit air(oxygen) and thus peak HP. Wins and losses come off the corners in restricted road racing. Not highest HP but most usable torque in the range you use gives the advantages. This means higher velocities than you would normally use, shorter cams on duration and lobe separation. Slightly smaller headers and ultra lite rotating assemblies. You will also gear the car to outrun the normal usable rpm range the components would dictate.
You ask for a velocity range and that changes with needs but 310-320 at the peak HP I want is what I aim for in the head. In the intake I go up to 280-300 through the runners. We must keep the velocity up to keep the fuel mixed. We are limited in our ability to run the rpm up to keep things in suspension, so we must use higher than normal velocities to do it. I’m sure you know at lower rpms fuel on the floor is not going to remix without a lot of quench/squish. You might add if that 272 is at .050 or advertised, 2 or 4 valve and what type of head is it. Someone may have already mastered the head and may be willing to share. Airspeed and turbulence management is KING in N/A engines, find the cfm demand of
the engine to make sure you reach the minimum cfm you need, and pay attention to the velocities.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- msu swppi 2010
- sat practice test 7 for assistive technology math test
- determining port velocity efi dyno tuning lc
- ap calculus free response questions
- topic c austin community college district
- activity 2 3 11 calculating property drainage answer key
- plot the course
- table 403 florida building
- formula sheet homestead
Related searches
- performance dyno tuning near me
- car dyno tuning near me
- lc resonance calculator
- determining acceleration from velocity graph
- dyno tuning near me
- auto dyno tuning near me
- dyno tuning colorado
- dyno tuning machines for sale
- dyno tuning shops near me
- motorcycle dyno tuning near me
- lc resonant frequency calculator
- windows efi boot manager utility