Series and Parallel



SERIES AND PARALLEL

Pre-Lab Question

What is the difference between voltage and current?

EXPLORATION

Materials

1 yellow multimeter (with leads)

1 battery board

1 alligator lead card

1. Build the circuit shown in the schematic below. The numbers indicate contact points where you will use the multimeter probes to measure voltage.

[pic]

Figure 1: Simple Circuit

Measure the voltage across the batteries to establish a benchmark. Although they are labeled 1.5V, the actual voltage may vary. Actual voltage can be greater than the labeled level with brand new batteries, and less than the labeled level for batteries that have been used. It is alright if the actual voltage is not exactly 6V.

To measure the battery combination voltage, be sure to measure from tip-to-toe of the whole combination.

Actual Voltage of Battery Combination: .

2.

• First, predict and explain what voltages (V) you will measure between the labeled points on the circuit. After, close the switch, and measure the voltage of the pairs on the circuit. Place the probes at contact points shown on the circuit diagram above and record below.

• Second, predict and explain what current (I) you will observe at each labeled point on the circuit. After, measure the current. To measure, you interrupt the circuit with the multimeter which means you disconnect the circuit at a point and use the multimeter to complete the circuit. Measure the current at the test points with the mA setting and record below.

|Contact Points|Predicted |Measured |Explanation of Prediction |

| | | | |

|V1-2 | | | |

| | | | |

|V2-3 | | | |

| | | | |

|V1-3 | | | |

| | | | |

|I1 | | | |

| | | | |

|I2 | | | |

| | | | |

|I3 | | | |

Explain your observations. What determines the voltages? How does the voltage of the components compare to the batteries voltage? Does current behave differently than voltage in a circuit and how?

Series Circuits

3. Build the circuit drawn in the schematic below.

• First, predict and explain the voltage for each pair of test points. After, measure the voltage and record below.

• Second, predict and explain the current for each test point. After, measure the current and record.

Figure 2: Series Circuit

|Contact Points|Predicted |Measured |Explanation of Prediction |

| | | | |

|V1-2 | | | |

| | | | |

|V2-3 | | | |

| | | | |

|V1-3 | | | |

| | | | |

|I1 | | | |

| | | | |

|I2 | | | |

| | | | |

|I3 | | | |

Explain your observations. How do light bulbs in series share voltage? How does this compare to the voltage of the battery? Why are they the same or different?

Parallel Circuits

4. Build the circuit shown below.

[pic]

Figure 3: Parallel Circuit

5.

• Predict what the voltage will be across each light bulb when you close the switch. How does this relate to the total voltage potential of the battery? Discuss with your group. After recording your prediction, close the switch and measure the voltage across the two light bulbs. Explain what you observe.

• Predict the current at each light bulb and for the whole circuit (test points a, b, and c). Discuss with your group and explain your prediction. Will current behave the same as with two bulbs in series?

|Contact Points|Predicted |Measured |Explanation of Prediction |

| | | | |

|V1-4 | | | |

| | | | |

|V2-3 | | | |

| | | | |

|Ia | | | |

| | | | |

|Ib | | | |

| | | | |

|Ic | | | |

How do voltage and current behave in a parallel circuit compared to a series circuit?

Challenge Work:

1. Describe a fast way to check if a light bulb circuit is series or parallel.

2. Why do you think most Christmas tree lights are wired in parallel?

4. Is the circuit in Fig. 2 or Fig. 3 more of a power drain on the battery? Explain.

APPLICATION

Materials

1 yellow multimeter (with leads)

1 battery board

1 alligator lead card

1. Build the circuit shown below.

[pic]

Figure 4: Series and Parallel Circuit

2. Predict the voltage across each bulb and across all the bulbs. Once you’ve recorded your prediction, measure the voltages. Explain your observations.

|Contact Points |Predicted |Measured |Explanation of Prediction |

| | | | |

|V1-2 | | | |

| | | | |

|V2-3 | | | |

| | | | |

|V2-4 | | | |

| | | | |

|V1-4 | | | |

3. Predict the current at each point in the circuit. Once you’ve recorded your prediction, measure the currents at each test point. Explain your observations.

|Contact Points |Predicted |Measured |Explanation of Prediction |

| | | | |

|Ia | | | |

| | | | |

|Ib | | | |

| | | | |

|Ic | | | |

| | | | |

|Id | | | |

| | | | |

|Ie | | | |

4. Observe the lights with the switch closed. Are all the bulbs equally bright? Explain what you observe.

What happened to the current after point 2 when there are two paths it could travel on?

Challenge Work: Predict what will happen when you unscrew light bulbs in the series and parallel circuit.

[pic]

Figure 5: Series and Parallel Circuit

a) Predict what will happen if you unscrew bulb 1. Explain your prediction.

b) Predict what will happen if you unscrew bulb 2. Explain your prediction.

c) Predict what will happen if you unscrew bulb 3. Explain your prediction.

6. Unscrew each bulb and observe what happens. Record your observations. Do they agree with your predictions? Explain.

a) Bulb 1 unscrewed.

b) Bulb 2 unscrewed.

c) Bulb 3 unscrewed.

Summary:

Final Clean-up

Please disconnect all alligator leads and reattach them to the clip card. Replace all equipment to the carts.

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download