KIT one: 300B loftin white price for one PCB all ...



KIT one: 300B loftin white price for one PCB all components included

(inclusive output transformer): 300 EURO mono version

KIT two: just with the extra interstage tranformers LL1660 Lundahl

KIT powersupply: PCB version: 175 EURO (stereo version)

KIT fully hardwired version complete with wooden chassis all components

(see 2A3 SE): 995 EURO

Choice of TWO chassis: one metal with GLASS: 150 Euro

One wooden chassis: 100 EURO

I must tell you that my first project was actually a SE 300B

I started with the classic loftin white circuit that you can find

in Jean Hiraga’s book allthough he uses a ECC83 , I find

a 6SN7 better suited for the purpose .

The main problem is allways hum , the only way to get rid

of that is by using DC on the filaments , and as ever good

regulation and filtering of the power supply will help . ! ! ?

I am a fervent supporter of negative Bias , it makes the amp

faster and the sound doesn’t have to go through a capacitor

and you dont waste power in a cathode resistor .

I Chose a 3K primary because it gives less distortion then

a lower plate resistance (which would give more power)

Okay the first schematic is exactly that

V1 half a 6SN7 and Zo a Lundahl LL1623/90mA 3K primary

The HT can be anyware from 250 to 550 Volts

That is if you use Krone Valves you can exceed the 400 Volts

and adjust the 10 Kohm if you exceed 400 Volts

The 2 nd part of the schematic are for those of you

who fear that the negative bias supply might have a

problem which would destroy your precious tubes

The Third part of the schematic is my version of an interstaged

300B, I used the 6DN7 which is a marvelous tube that has

a very interesting power section 10 watts , good for 30 mA

at 300 volt and a nice little second section

note the 10/400 cap is an MKP

Anyway have fun if you intend to build this you ‘ll be in for a

pleasant surprise .

About the power supply :

The simplest way is a tube rectified choke loaded supply ,

Its is extremely musical and easy to build

The sound quality changes dramatically with the rectifier tube

The 5U4G will work so will a GZ34,32,5R4

But the winners are GZ37 & 274b

If you want to use a semiconductor engineerd PSU check out the

PSU we offer as a kit.

You can buy a nice housing as well , we have 2 models

The classic one and the modern one with cooling fans and the tubes

and transformers inside (safer)

a picture:

PRICE FOR THE ASSEMBLED VERSION with the KR VV300B: 2000 Euro

Je doit vous dire que mon premier projet était un SE 300B

avec un circuit que vous pouvez trouver dans le livre de

Jean Hiraga, même s’il utilise un ECC83, je trouve le

6SN7 un meilleur tube pour cette application.

Le problème principal c’est toujours le bruit de fond, la

seul façon de l’éliminer est d’utiliser du courant continue

pour alimenter les filaments des tubes, et bien sûr une

alimentation bien filtre et bien règle est aussi primordial.

Je suis un fana de BIAS négative, l’ampli devient plus

rapide et le son ne doit pas traverser un condensateur

et en plus vous ne perdez pas de puissance dans une

résistance de cathode.

J’ai choisis une impédance primaire de 3Kohm, parce que

il y moins de distorsion que avec une résistance de plaque

plus basse (qui donne plus de puissance).

Bon le premier schéma est exactement celui la.

V1 est un demie 6SN7 et Zo est un Lundahl LL1623/90mA 3K

primaire.

La Haute tension peut être entre 250 et 550 Volt

A condition d’utiliser les tubes de Krone vous pouvez

monter au dessus 400V en HT et ajuster 10Kohm au dessus

400 Volt.

La deuxième partie du schéma est pour eux qui ont

peur que l’alimentation de Bias négative peut avoir

des conséquences destructives de vos précieux tubes.

La 3ieme partie est ma version d’un 300B avec transformateur

d’étage, avec le merveilleux tube 6DN7 qui a une puissance

de 10Watt, bien pour 30mA a 300V.

Le condensateur 10/400V est un type MKP

Si vous pensez le construire vous aurez une agréable surprise.

Au sujet de l’alimentation:

La méthode la plus simple est une alim a tube avec une

self de filtrage, très simple a construire et très musical.

La qualité du son ce change énormément en fonction

du tube redresseur.

Le 5U4G fonctionne ainsi un GZ34,32,5R4

Mais les vainqueurs sont les GZ37 & 274B.

Si vous voudrez une alimentation a Diodes jetez un coup d’oeil

a notre page Power Supply q’on vous propose en Kit.

Vous pouvez aussi acheter un joli châssis, on a deux modelés:

La version classique et la version moderne avec les tubes et les

ventilateurs a l’intérieur. (plus de sécurité)

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download