Reorder Number Vinyl Bulk Assortment (Pk/30)
BPV801
Vinyl Bulk Assortment (Pk/30)
PLAY. LEARN. SHARE.
blog
Find ideas on the S&S Blog:
? Crafts & DIY
? Senior Activities
? Summer Camp ? Education & Classroom
@SSWorldwidecatalog . @ssworldwide
@ssworldwide @SSWorldwide
MAKING IT EASY to SAVE MORE on your next order!
15% OFF No $ Minimum
Please mention Offer Code: M2467
Limit one per order. May not be combined with other offers
or bid or contract pricing. See for Offer Terms and Conditions.
We reserve the right to terminate this offer at any time without notice.
?
Call Toll-Free
1-800-243-9232
Online:
Email: cservice@
FAX: 1-800-566-6678
? Copyright 2018 S&S? Worldwide Inc. All rights reserved. No part of this project may be copied or duplicated without the express written permission of S&S Worldwide.
Kit may contain silicone gel packets, which should be removed before use.
Reorder Number
BPV801
2.1
Vinyl Bulk Assortment (Pk/30)
PLEASE READ ALL INSTRUCTIONS BEFORE STARTING
AGE GROUP: 8 and up PROJECT TIME: 45 minutes
YOUR KIT CONTAINS: ? Vinyl Pieces ? Cord Lacing
YOU WILL NEED: ? Scissors ? A Ruler
EACH PERSON SHOULD HAVE: ? A project of his/her
choice and length of cord needed.
BPV801
INSTRUCTIONS:
Refer to Figure A to determine how much cord is needed for each project. Cut lengths as needed.
Helpful Hints:
After cutting lace to the required length, cut one end to a long point for the working end. This will make it easier to lace through the holes.
Whip Stitch: Requires approximately 3 inches of lacing for every
inch of edge to be laced.
1. Line up your project, holding it with the front facing toward you. Start lacing at the least noticeable place (see Figure A).
TIP: When lacing, make sure that the lace does not twist. If lace
should twist, run lace between the thumb and finger from the project down to the end.
Pull lace snug, using the same amount of tension on each stitch. When going around corners, lace twice in corner hole.
2. At the starting hole, push lacing through from front to back leaving a 1" tail. Continue by bringing working end over and through the next hole (see Figure B).
3. Finish by pushing working-end through the starting hole. Then from in between the parts, pull both the tail and the working end out and run them under several stitches. Cut off extra lace (see Figure C).
FIGURE A
Use a whip stitch and start each project where you see the arrow.
Start
Start
Measure Approx. 37" Lacing
Measure Approx. 50" Lacing
Round Bottom Coin Purse
4 Hooked Key Case
STEP 3
Coin Purse
Start
Measure Approx. 35" Lacing
Measure Approx. 43" Lacing
Start
Belt Loops
Pen and Pencil Holder
Measure Approx. 55" Lacing
FIGURE B FIGFUIRGEUCRE C
6 Hooked Key Case Start
FIGURE C FIGFUIRGEUBRE B
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- reorder stock symbols yahoo finance
- dataframe reorder columns
- reorder variables in sas dataset
- reorder columns sas
- sas reorder columns in table
- sas reorder variables in output
- bank of america reorder checks by phone
- need to reorder checks
- sas reorder columns in dataset
- sas retain to reorder variables
- bulk 30 carbine reloading bullets
- the number 30 meaning