Residential Load calculator instructions
STEP 1
1. Enter your company information. 2. Enter your client information. 3. Enter the design temperatures ? The indoor design temperatures are normally 70F for the winter and 75F for
the summer, however, you may enter other temperatures if needed. The outdoor design temperatures can be found on Table 1 in Manual J or by searching for `outdoor design temperatures' on the internet. Note: the outdoor design temperature for Raleigh, NC is listed as 92F. Experience has shown the temperature regularly reaches the mid 90's, therefore, I took the liberty to use 95F. 4. Enter the direction house is facing. 5. Enter the heated or cooled area of the house. 6. Select the humidity level for your area. 7. Select the tightness of the construction. 8. Select the number and tightness of fireplaces if any exist. Ventless fireplaces and those obtaining all combustion air from outside are considered tight 9. Enter the number of occupants in the home. Typically, this is the number of bedrooms plus one.
STEP 2
Overhang characteristics
1. Enter the distance between the top of the windows and the overhang (A) for each corresponding direction. Enter only feet decimally. For example: 6 inches =.5
2. 2. Enter the distance the overhang sticks out from the wall (B) for each corresponding direction. Enter only feet decimally. For example: 1 foot 6 inches = 1.5
3. Enter the total linear feet across the top of all windows under the overhang for each corresponding direction. For example: if there are four windows under an overhang facing east and each is 3', 4', 3' and 5' across the top, respectively, then you would enter 15.
Is it an overhang or a porch?
If the window is located under a structure that is always totally shaded such as a porch, awning or carport, then it is considered as facing north thus, its area should be included with the north facing windows. In the Sample House Plan the only window facing east is under a covered porch, therefore, its area is added to the North facing windows and there are no east facing windows.
Fenestration (Glass)
1. If the window manufacture's specs are available, check the box and enter the latitude, U-value and SHGC. (Do not select type of glass if manufacture's specs are used)
2. Enter the area (sq. Ft.) of all windows facing north. Include any permanently shaded windows, even if facing another direction. Enter the area of all remaining windows facing their respective direction.
3. If you did not use manufacture's specs, select the type of glass from the dropdown. 4. If glass has reflective coating, select YES, otherwise NO 5. Enter area (sq. ft.) of skylight and select type of glass
The total solar gain is the total amount of btuh entering the house through all glass surfaces. It takes into account both radiation and conduction.
Ducts 1. Select location of duct work 2. Select insulation on ducts 3. Select whether `sealed' or `unsealed' 4. Enter the ceiling or floor area the ductwork is either above or below. For example: The Sample House is one story and all ductwork is in the attic, laying on a 1768 sq. ft. ceiling. Therefore, enter 1678. If, however, the home is 2 stories (839 sq. ft. on each floor) then only the duct work in the upper ceiling would be exposed to outside conditions. In which case, you would enter 839. 5. Select the attic temperature. Make your best guess as this is a function of radiant heat, conduction and attic ventilation.
Load calculation 1. Enter the gross area of all exposed walls* the wall. Gross area is the total area including windows and doors Gross area = perimeter of house x wall height
*Exposed wall means any wall that is exposed to the outdoor conditions. Also includes any wall between a conditioned and unconditioned space. Example: the wall between the house and unheated garage is exposed. 2. Glass 1- Value is entered automatically. Select type of glass 3. Glass 2- Enter the area (sq. ft.) only if there is a significant amount of different glass. For example: one half the house has single glass while the other half is double glass. 4. Skylight- Enter the area (sq. ft.) of skylight and select type of glass. 5. Doors- Enter area of doors and select insulation value. (Note: separate the glass from doors. If a west facing 3' x 7' door is half-glass, then enter 11 sq. ft. in the door cell and 10 sq. ft. in Step 2, west facing windows Sliding glass doors should be treated as windows 6. Net Wall- Automatically calculated
Net Wall = Gross wall - all openings 7. Ceiling- Enter the area of all exposed ceilings. The Sample house has 1768 sq. ft. of exposed ceiling, If the house
were 2 stories (839 sq. ft. on each floor) then it would only have 839 sq. ft. of exposed ceiling
8. The EMS lad calculator offers three types of floors: a. Floors over crawl space ? enter square feet, select insulation b. Floors over open area - enter square feet, select insulation c. Slab floors ? enter linear feet, select insulation
9. Infiltration: Enter the cubic feet of the house (area x average ceiling height). The program will calculate the heating and cooling loads due to infiltration based on the tightness selected in Step 1
10. Appliances ? A default value of 1200 btuh is programed into the software. If you wish to change the value, click on the check box next to `Enter Value' and enter a new value. Use this feature if an abnormal number of appliances are present, such as computers and big screen TV's.
11. Summary ? The summary will give the heating and cooling loads. Heating Load ? Use this load to size the furnace or boiler. Always use the output rating.
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related searches
- instructions on how to use baking soda to pass a drug test
- sure jell instructions pdf
- basic excel spreadsheet instructions pdf
- excel instructions manual
- residential mortgage payment calculator free
- residential heat load calculation software
- printable residential load calculation sheet
- residential electrical load calculation pdf
- residential cooling load calculation
- nec residential load calculation worksheet
- residential heat load calculation worksheet
- manual j residential load calculation pdf