Pro-line Side Dump Combination Spreader



| | | |

| | |

| |SPECIFY: ____________ |

| |Make: _______________ |

| |Model: _______________ |

|- The body unit will be a combination spreader design capable of dumping to the rear via a front |YES: |NO: |

|mounted, top lift hoist as per conventional dump bodies. The unit will have radius side panels to | | |

|permit gravity flow unloading via an integral main conveyor, centered and recessed along the inside | | |

|length of the unit. | | |

| | |

|DIMENSIONS: | |

| | |

|- Body overall length 132 inches maximum, measured from outside edge of rear apron to front edge of |SPECIFY: ____________ |

|hoist cradle. | |

|- Body inside length 120 inches minimum. |SPECIFY: ____________ |

|- Body outside width 96 inches maximum. |SPECIFY: ____________ |

|- Body inside width 86 inches minimum. |SPECIFY: ____________ |

|- Body front panel height 53 inches from top of conveyor floor. |SPECIFY: ____________ |

|- Side height 38 inches from top of conveyor floor. |SPECIFY: ____________ |

|- Tailgate height 46 inches from top of conveyor floor. |SPECIFY: ____________ |

|- Capacity 6.0 cubic yards at water level. |SPECIFY: ____________ |

|-Capacity with 10-inch side boards at water level 8.1 cubic yards. |SPECIFY: ____________ |

|- Installed body weight 4,250 lbs maximum. |SPECIFY: ____________ |

|- The body shall fit on a chassis CA/CT of 102 inches maximum. |SPECIFY: ____________ |

| | |

|CONSTRUCTION: | |

| | |

|- Body to be constructed from one-piece head-sheet and side panels fabricated from a minimum 3/16” |YES: |NO: |

|Cor-ten A corrosion resistant material. | | |

|- Body front panel shall be completely clean and clear of any type of recess and/or protrusions into |YES: |NO: |

|the body including hoist bulkheads, dog houses, etc. | | |

|- Top horizontal rails shall be minimum 4” X 4” X 3/8” wall HSS tubing. |YES: |NO: |

|- Rear vertical corner-posts to be minimum 10 GA sheet, fabricated in such a way as to allow for the |YES: |NO: |

|inclusion of rear facing optional lighting requirements. | | |

|- Rear vertical corner-posts to be tied to radius side panels and horizontal top rails and welded 100|YES: |NO: |

|percent. | | |

|- Rear vertical corner-posts to be connected to main conveyor via a rear horizontal 3” X 8” X 3/8” |YES: |NO: |

|wall HSS tube spanning the full body width. | | |

|- Body construction shall include integral side fenders fabricated from a minimum 10 GA Cor-ten A |YES: |NO: |

|corrosion resistant material. | | |

|- Integral fenders to be sloped away from unit to prevent any excess material spilled during loading |YES: |NO: |

|from building/piling up. | | |

|- Body access via 15-inch wide, two-piece fold-up ladder located at the rear curb (right hand) side |YES: |NO: |

|of unit. | | |

| | | |

|MAIN CONVEYOR: | |

| | |

|- Main conveyor to be three-piece formed construction centered and recessed along the full length of |YES: |NO: |

|the dump box floor. | | |

|- Construction shall be 1/4” Cor-ten A corrosion resistant material for both main conveyor frame and |YES: |NO: |

|body long sills. | | |

|- Conveyor sides to be fabricated in such a manner to include integral chain link covers. |YES: |NO: |

|- Conveyor sides to include vertical slots at both drive and idler shaft mounting locations to allow |YES: |NO: |

|shaft assemblies to simply drop out, providing easy access and simplifying maintenance. | | |

|- Replaceable conveyor wear-plate fabricated from AR 450 abrasion resistant steel plate. |YES: |NO: |

|- A mild steel conveyor shield shall be supplied to protect the conveyor chain when the spreader is |YES: |NO: |

|not in operation. | | |

|- A full-length polymer spill guard attached to the conveyor underside to prevent any material |YES: |NO: |

|carried back on the underside of the main conveyor from falling on chassis components. | | |

|- A high torque low speed hydraulic motor through a 25:1 planetary gearbox shall drive the main |YES: |NO: |

|conveyor with sufficient torque to discharge sand and salt through the control gate to the spinner. | | |

|- Specify make and model of planetary gearbox. |SPECIFY: ____________ |

|- Conveyor chain to be self-cleaning D667 pintle type with a minimum tensile strength of 30,000 PSI, |YES: |NO: |

|spaced apart 21 inches on center. | | |

|- Scrapper bars to be 1/2” X 1 1/2” spaced every 2nd link. |YES: |NO: |

|- All conveyor flights shall be 100% fully welded. |YES: |NO: |

|- Drive and idler shafts to be two (2) inch high-resistance stress proofed SAMSON 100. |YES: |NO: |

|- Drive and idler sprockets to be minimum eight-tooth cast steel. |YES: |NO: |

|- All sprockets to be minimum C1030 cast steel. |YES: |NO: |

|- Drive and idler shafts to be mounted into unit via four (4) bolt self-aligning flange bearings. |YES: |NO: |

|- Conveyor chain tension to be regulated via an automatic chain tensioning system. This tensioning |YES: |NO: |

|system will provide appropriate chain tension for the main conveyor chain at all times and under all | | |

|normal operating conditions. | | |

|- Chain tensioning system to be centrally located between main conveyor drive and idler shafts. |YES: |NO: |

|- Access to conveyor chain tensioning system shall be from the side(s) of the body. |YES: |NO: |

| | | |

|TAILGATE: | | |

| | | |

|- Tailgate to be a double acting rectangular construction design. |YES: |NO: |

|- Upper hinge plates to be offset design flame cut from 1-inch steel plate. |YES: |NO: |

|- Exterior vertical side support tubes to be 3 1/2” X 3 1/2” X 1/4 wall HSS tubing. |YES: |NO: |

|- Tailgate sheet shall be minimum 3/16” Cor-ten A corrosion resistant material. |YES: |NO: |

|- Tailgate sheet to be reinforced with formed horizontal stiffeners fabricated from a minimum 3/16” |YES: |NO: |

|Cor-ten A corrosion resistant material. | | |

|- Positive tailgate latching to be achieved via dual air brake chambers directly coupled to 1/2” |YES: |NO: |

|thick flame cut latch plates. | | |

| | | |

| | | |

| | | |

| | | |

|SPINNER ASSEMBLY: | | |

| | | |

|- A 3.0 cubic inch hydraulic motor shall drive the spinner assembly, which shall be mounted at the |YES: |NO: |

|rear of the truck frame | | |

|- The spinner assembly shall mount in plate installed at rear end of the chassis frame and shall be |YES: |NO: |

|removable for summer operation | | |

|- The spinner shall be capable of spreading evenly up to a 20 FT radius with a main operating range |YES: |NO: |

|of 0 to 15 FT radius. | | |

|- Hydraulic hoses to the spinner motor are to be complete with quick disconnect automatic sealing |YES: |NO: |

|breakaway couplers and are to be assembled so that the male end may plug into the female end on the | | |

|spinner motor and the hoist frame when the spinner assembly is disconnected. | | |

|- Steel discharge chute and poly spinner disc to be supplied. |YES: |NO: |

| | | |

|HOIST CYLINDER: | | |

| | | |

|- Hoist lift cylinder to be forward mounted three- (3) stage top lift telescopic. |YES: |NO: |

|- Capacity 20 tons at 2,000 PSI. |YES: |NO: |

|- Hoist cylinder running surface shall be nitrated. |YES: |NO: |

|- The hoist shall be capable of lifting the box and the normal contents of sand plus 20%. |YES: |NO: |

|- Rear dump angle variable up to 50 degrees from horizontal. |YES: |NO: |

| | | |

|SAFETY BAR: | | |

| | | |

|- The body to be equipped with a positive locking support brace. |YES: |NO: |

| | | |

|LIGHTING: | | |

| | | |

|- A basic light kit complying with FMVSS/CMVSS 108 lighting requirements shall be supplied as |YES: |NO: |

|standard equipment with each unit. | | |

|- Lights and wiring shall be completely sealed with corrosion and vapor proof lamps and junction box.|YES: |NO: |

|Oval Stop, Tail & Turn with Amber strobe lights |YES: |NO: |

|WELDING: | | |

| | | |

|- All welds shall be continuous type and shall not permit any moisture to be trapped in the joints. |YES: |NO: |

| | | |

|PAINT: | | |

| | | |

|- Body to be shot blasted prior to paint application. |YES: |NO: |

|- Epoxy primer to be applied. |YES: |NO: |

|- Body to be painted with one color County Supt to determine |YES: |NO: |

|WARRANTY: | | |

| | | |

|- Minimum one-year parts and labor on all components from date of delivery of finished unit. |YES: |NO: |

| | | |

|MANUALS: | | |

| | | |

|- Parts and service manual for each unit to be supplied. |YES: |NO: |

| | | |

|ADDITIONAL EQUIPMENT: | | |

| ½ Cab shield |YES: |NO: |

|. Strobe light mounted on bracket extending forward from wing mast over roof of truck cab |YES: |NO: |

|. | | |

| | | |

|- Body top material screens. |YES: |NO: |

|- LED model 60 stop, turn & tail lighting kit in rear corner posts. |YES: |NO: |

|Option #1 Price separately |YES: |NO: |

| | | |

|- VCL liquid pre-wetting systems. | | |

| Option #2 Price Separately |YES: |NO: |

|Dickey John ICS 2000 Control point automated sander control | | |

| | | |

| | | |

| | | |

| | | |

| | | |

| | | |

| | | |

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download