PAST EXAM PAPER & MEMO N1 - Engineering N1-N6 Past Papers ...

Website: previouspapers.co.za

Email: info@ previouspapers.co.za CELL: 073 770 3028

PAST EXAM PAPER &

MEMO N1

ABOUT THE QUESTION PAPERS AND ONLINE INSTANT ACCESS:

THANK YOU FOR DOWNLOADING THE PAST EXAM PAPER AND ITS MEMO, WE HOPE IT WILL BE OF HELP TO YOU. SHOULD YOU NEED MORE QUESTION PAPERS AND THEIR MEMOS PLEASE SEND US AN EMAIL TO INFO@ PREVIOUSPAPERS.CO.ZA AND WE WILL SEND YOU A FULL DOWNLOAD VERSION OF THESE THOUGH A FULL DOWNLOAD COMES AT A COST.

ALTERNATIVELY YOU CAN PURCHASE THEM ONLINE FROM OUR WEBSITE WWW.PREVIOUSPAPERS.CO.ZA

TO AVOID DELAYS AND YOU FOLLOW ALL THE NEEDED STEPS TO GET INSTANT DOWNLOAD. WITH ONLINE PAYMENT YOU CAN GET INSTANT DOWNLOADS OF YOUR PURCHASE.

WE SELL PREVIOUS PAPERS AND MEMOS FOR THE SUBJECTS MENTIONED AND THE PAPERS ARE BETWEEN 2014-2019. THE PAPERS ARE IN PDF FORM AND EACH PDF HAS A MINIMUM OF SEVEN DIFFERENT PAPERS. THE YEARS FOR THE PAPERS YOU ARE PURCHASING ARE ALSO INCLUDED ON THE WEBSITE.

PRICE OF THE PAPERS AT A BIG DISCOUNT

Previous papers are very important in ensuring you pass your final exams. The actual value of the papers we are making you access is way more than R1 000 and we are making these very cheap as we have you in mind. For a small amount you can have these papers.

THE COST PER SUBJECT IS R300.

Website: previouspapers.co.za

Email: info@previouspapers.co.za

T510(E)(M22)T APRIL EXAMINATION NATIONAL CERTIFICATE

ENGINEERING DRAWING N1

(8090261) 22 March 2016 (X-Paper)

09:00?13:00

REQUIREMENTS: ONE A2 Drawing Sheet Calculators and drawing instruments may be used.

This question paper consists of 5 pages and 4 diagram sheets.

Copyright reserved

Please turn over

(8090261)

-2-

T510(A)(M22)T

DEPARTMENT OF HIGHER EDUCATION AND TRAINING REPUBLIC OF SOUTH AFRICA

NATIONAL CERTIFICATE ENGINEERING DRAWING N1

TIME: 4 HOURS MARKS: 100

INSTRUCTIONS AND INFORMATION

1.

Answer ALL the questions.

2.

Read ALL the questions carefully.

3.

Number the answers according to the numbering system used in this question

paper.

4.

Marks will be deducted for untidy work.

5.

ALL drawings must be done neatly using drawing instruments.

6.

ALL drawings must conform to the latest SANS Code of Practice.

7.

ALL work you do not want to be marked must be clearly crossed out.

8.

Write neatly and legibly.

Copyright reserved

Please turn over

(8090261)

-3-

T510(A)(M22)T

QUESTION 1: FREEHAND

Figure 1, DIAGRAM SHEET 1, shows a view of a planer.

Only use a pencil and eraser and draw the given view of the planer, 1.5 times the given

size.

[10]

QUESTION 2: REPRODUCTION DRAWING AND GEOMETRICAL CONSTRUCTION

Figure 2, DIAGRAM SHEET 2, shows a view of a pump cover.

2.1

Draw to scale 2 : 1 the view of the pump cover

(9)

2.2

Show all construction lines used in the construction of the ellipse.

(2)

2.3

Insert any SIX dimensions.

(2)

2.4

Draw the following title and scale centrally beneath the layout:

PUMP COVER

SCALE 2 : 1

(2)

[15]

QUESTION 3: FIRST-ANGLE ORTHOGRAPHIC PROJECTION

Figure 3, DIAGRAM SHEET 3, shows an isometric view of a casting.

DO NOT draw the given views, but draw to scale 1 : 1, and in first-angle orthographic projection the following views:

3.1

A front view in the direction of 'F'

(5)

3.2

A left view in the direction of 'L'

(5)

3.3

A top view in the direction 'T'

(5)

3.4

Add the following title and scale centrally beneath the layout:

CASTING

SCALE 1 : 1

(2)

3.5

Draw the symbol for first-angle orthographic projection beneath the layout.

(1)

[18]

Copyright reserved

Please turn over

(8090261)

-4-

T510(A)(M22)T

QUESTION 4: ISOMETRIC DRAWING

Figure 4, DIAGRAM SHEET 4, shows two views of a bracket drawn in first-angle orthographic projection.

DO NOT draw the given views but draw to scale 1 : 1 an isometric view of the bracket.

Point 'P' must be the lowest point.

No hidden detail required [10]

QUESTION 5: SECTIONAL DRAWINGS

Figure 5, DIAGRAM SHEET 5, shows a half sectional front view and a top view of a hanger bearing drawn in first-angle orthographic projection. Draw to scale 1 : 1 and in first-angle orthographic projection the following views of the hanger bearing:

5.1

A full sectional front view on cutting plane F?F

(5)

5.2

A left view

(5)

5.3

A top view

(4)

5.4

Add the following title and scale centrally beneath the layout:

HANGER BEARING

SCALE 1 : 1

(2)

5.5

Draw the symbol for first-angle orthographic projection beneath the layout.

(1)

[17]

QUESTION 6: PRISMS AND PYRAMIDS

Figure 6, DIAGRAM SHEET 6, shows front and auxiliary view of a hexagonal pyramid.

Draw in first-angle orthographic projection and to scale 1 : 1 the following views of the pyramid:

6.1

The given front and auxiliary view

(4)

6.2

A top view in the direction 'T'

(5)

6.3

A left view in the direction 'L'

(5)

No hidden detail required [14]

Copyright reserved

Please turn over

(8090261)

-5-

T510(A)(M22)T

QUESTION 7: COMPUTER TERMINOLGY AND ABBREVIATIONS

Draw the answer block as shown in FIGURE 7 below, to full size on the DRAWING SHEET.

Print the answers of the following questions in the table drawn on the drawing sheet.

7.1

Name ONE input device a draughtsman uses to produce a drawing.

(1)

7.2

Name ONE output device a draughtsman uses to produce a drawing.

(1)

7.3

Name ONE computer hardware used on the CAD system.

(1)

7.4

Write down the terminology of the following abbreviations

7.4.1

CAD

(1)

7.4.2

PCD

(1)

7.4.3

HEX

(1)

7.1

7.2

7.3

7.4

7.4.1

7.4.2

7.4.3

FIGURE 7

(6)

NOTE: A balanced layout and neatness of the complete ANSWER SHEET.

(10)

[16]

TOTAL: 100

Copyright reserved

(8090261)

-1-

DIAGRAM SHEET 1

T...(A)(M22)T

FIGURE 1

Copyright reserved

FIGURE 2

(8090261)

-1-2- -

DIAGRAM SHEET 2

T...(A)(M22)T

FIGURE 3

Copyright reserved

FIGURE 4

 ................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download