Three-dimensional Image Manipulation in Patients with ...



Three-dimensional Image Manipulation in Patients with Facial Skeletal Asymmetry: From Concepts to Surgical Practice

Yong-Ming Chu, MD, David E. Morris, MD, and Yu-Ray Chen, MD

INTRODUCTION: Recently there has been tremendous evolution both in the quality of three-dimensional computed tomography (3DCT) and in the sophistication of software for manipulating those images. This technology has been used recently in the morphologic analysis of patients with facial asymmetry (1,2). While it has also been used in surgical planning, for example implant fabrication (3); the practical applications for this technology are evolving. At our center we recently have been using image manipulation software to plan facial contouring operations for young adult patients with facial asymmetry. Here we present our approach in using such software to plan corrective procedures in three patients.

METHOD: Three Taiwanese women of ages 21, 33, and 28 (patients 1, 2, and 3, respectively) presented to our clinic, each with the complaint of facial asymmetry. In patients 1 and 2, the asymmetry was developmental, affecting primarily the mandibular ramus and body (Figure 1; all images refer to patient 2). Patient 3 had undergone previous cosmetic contouring of the zygomas, mandibular angles, and chin by another surgeon and now sought consultation for mandibular angle asymmetry and a disproportionately long lower face.

[pic]

Figure 1. Patient 2, a 33-year-old female with asymmetry, primarily of the lower face.

For each patient a facial 3DCT was obtained and CT data was imported into Amira 3.1.1 software (Mercury Computer Systems Inc. San Diego, CA) to create a 3D skeletal model. A midline skeletal plane was constructed using the nasion, nasal septum, anterior nasal spine, and dental midline. The image was rotated posteriorly to assure that the most clinically applicable plane was chosen. Based on the patient and surgeon’s subjective feeling of her most aesthetically favorable side, a mirror image was created of the corresponding computer-generated hemiskeleton. The actual and mirror images were compared through digital subtraction to determine the type and extent of contouring that would best achieve skeletal symmetry. This resulted in a 3D representation having specific dimensions (measured in millimeters) of the portion of skeleton to be augmented, or reduced (Figures 2,3).

[pic] [pic]

a. b.

Figures 2a,b. (a.) Level of transverse CT section through mandibular ramus. (b.) Planned extent of resection, obtained through mirror imaging (small arrow) has been transposed onto the corresponding actual preoperative CT section (large arrow).

[pic] [pic]

a. b.

Figures 3a,b. (a.) The mirror image of the left hemimandible has been digitally subtracted from the actual right hemimandible. The irregularly shaped segment represents this difference. (b.) Planned removal of this segment to achieve skeletal symmetry. Note that thicknesses of this segment are marked at various points.

The asymmetry was corrected through mandibular angle resection (patient 1) and burring of the outer cortex of the hemimandible to the extent and in a manner to achieve a bony resection having the morphology of the planned segment to be resected (patients 1, 2). Patient 3 underwent osseous shortening genioplasty and augmentation of the left mandibular angle with a Medpor prosthesis. The prosthesis was contoured intraoperatively to the form and dimensions calculated by our simulation. Postoperative CT scans were superimposed onto preoperative scans to determine accuracy of resection.

RESULTS: Pre and postoperative CT superimposition revealed good correlation between the resected hemimandible and the planned area of resection (Figure 4). Each procedure was performed without complication and postoperatively each patient has demonstrated significant improvement in facial contour (Figure 5).

[pic]

Figure 4. Postoperative 3DCT facilitates correlation between planned segment of resection (small arrow) and actual segment of resection (large arrow).

[pic]

Figure 5. Patient 2, following contouring of the right mandibular ramus and body.

CONCLUSION: The use of 3DCT combined with mirror imaging software has enabled a quantitative preoperative morphologic analysis of the defect in this group of young adults with facial asymmetry. It has facilitated a surgical approach characterized by quantitative endpoints of recontouring. Our early experience is promising in that this relatively simple technique has afforded significant clinical improvement in this group of patients.

REFERENCES

1. Kwon TG, Park HS, Ryoo HM, et al. A comparison of craniofacial morphology in patients with and without facial asymmetry – a three-dimensional analysis with computed tomography. International Journal of Oral and Maxillofacial Surgery 35:43-48, 2006.

2. Katsumata A, Fujishita M, Maeda M, et al. 3D-CT evaluation of facial asymmetry. Oral Surgery Oral Medicine Oral Pathology Oral Radiology and Endodontics 99:212-220, 2005.

3. Wong T-Y, Fang J-J, Chung C-H, et al. Comparison of 2 methods of making surgical models for correction of facial asymmetry. Journal of Oral and Maxillofacial Surgery 63:200-208, 2005.

................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download