Activity 3.2.2 Loads
[pic]
|Activity 3.2.2 Loads |
Introduction
Once an architectural program has been devised and a preliminary structural system has been chosen, the structural engineer may begin the process to design the structural elements. This requires that the engineer identify the design loads for each structural element. Once the applied design loads have been determined, the loads must be traced through the structure so that the load(s) are included in the design of each element through which the load(s) will travel.
In this activity you will determine design loads for the roof of a high school in a suburb of Chicago, Illinois (enrollment 2500) and select appropriate roof joists (beams) based on the loads transferred to the joists.
[pic]
ROOF PLAN
Equipment
Engineering notebook
Pencil
Calculator
IBC Figure 1608.2 Ground Snow Loads for the United States
Roof Deck Span-Load Table
IBC Table 1604.5 Occupancy Category Table
Importance Factor Table
IBC Table 1607.1 Minimum Live Loads
Weight of Materials Table
K-series Standard ASD Load Table for Open Web Steel Joists
Keystone Library Renovation Preliminary (student version).rvt
Procedure
You will calculate the design loads for the roof and choose a steel roof deck to carry the loads. You will then chase the loads to the roof beams (joists). Based on the uniform beam loading, you will then choose an open web steel joist that can carry the applied beam loading.
Criteria
The low-slope roof will be constructed of a steel roof deck, five inches of rigid insulation, and a built-up roof (BUR).
Assume a double span (based on cost comparison for this project) for the roof deck. Note that a double span simply means that the deck is cut so that it continuously spans from one beam, over the top of a second, and ends at the third support beam (see ROOF PLAN).
The roof will support a mineral fiberboard suspended ceiling.
The roof will support mechanical, electrical, and plumbing equipment (MEP). Assume 10 psf for all of this equipment.
The building is located in an urban environment surrounded by other buildings.
Calculate the snow load for the low-slope (flat) roof. For this structure we will use the following coefficients.
Ce = 1.0 assuming an urban or suburban area surrounded by other buildings such that the building is partially exposed to the wind.
Ct = 1.0 assuming the building is heated and loses some heat through the roof.
Cs = 1.0 because the roof is low-slope.
Find the roof live loading required by the IBC.
Estimate the dead load of the roofing system by estimating the weight of all of the roof components. Note that typically the ceiling and PEM will be supported by the roof framing (and not the roof deck), but conservatively include these loads for all roof calculations.
Determine the total design load for the roof system.
Select a steel roof deck (double span) to support the required loads. Note that you may specify single, double, or triples spans for the roof decking depending on the relative material and installation cost of each. Assume a double span for this particular application.
[pic]
Determine the roof beam loading for both the interior and exterior beams.
Choose open web steel joists to act as the roof beams. For now, use only the top load values in the table and ignore the live load deflection load values. Assume the roof deck will be installed with a triple span.
Select an appropriate Type F roof deck and open web steel joist for the Keystone Library Renovation. Show all of your work and record all of your assumptions.
Revisit your Keystone Library Renovation 3D model and make appropriate changes to the roof system and roof framing to reflect your choices. Tag the roof joists and create a roof framing plan.
Conclusion
1. Why are dead load and live load considered separately? How do they affect the structure differently?
Because the dead load is the load that the roof will always have to support, while the live load can change because it includes the factors of a load that changes. The live load is the load that the roof will support by snow or by people getting on top of the roof.
2. What is the justification for requiring engineers to consider many load combinations when designing a structure rather than just one or two?
Because the building will be affected by more than just two factors. If you just considered that the roof could hold itself up with just the dead load of the roof and some people on top, then whenever it snows if it were to snow more than the weight of those people then it would collapse the building hurting people or damaging property.
How would the size of the roof decking and roof beams change if the spacing of the beams was increased? Why?
If the beams are farther apart then there would be a larger tributary width the beams would have to support. It would probably cause deflections in the floor if the beams were too far apart and a weight was applied to the middle of in between them. So the roof beams and the roof decking would have to increase in size to help support the extra spacing
[pic]
-----------------------
BEAM
GIRDER
................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
Related searches
- 3 wing 2 the charmer
- 3 2 time signature example
- activity 9 2 cellular respiration answers
- minecraft 1 3 2 download free
- 3 to 2 ratio means
- 3 by 2 matrix calculator
- what is 3 2 repeating as fraction
- 3 2 divided by 5
- 3 2 solving linear systems by substitution
- log4 x 3 log2 2 x
- x 3 xy 2 y 3 1
- activity 9 2 modeling cellular respiration