“TUTORIAL Verizon E815 to Bell (Java)



“TUTORIAL Verizon E815 to Bell (Java)

Since there have been so many requests for an official tutorial on how to flash the E815 to the Bell firmware, I decided to make a tutorial. Most of the information is copied and pasted from the following page. I give full and complete credit to everyone szczuka has listed on his page. A special thanks to Mark_Venture and Aenemic Royalty

DISCLAIMER: I am NOT responsible for any possible damage done to your phone by a non successful flash. The odds of something wrong are HIGHLY unlikely, but there is always murphy’s law. If your flash is not successful, then flash back to the verizon E815 monster file and try again. Your phonebook WILL be lost after the flash. Be smart and use Motorola PST or bitpim to backup your phonebook.

What the software will do: The bell software will upgrade many features on your phone. You will notice that you will now how full Bluetooth without need of seem editing, and most of all, you will have the Java platform(ability to upload applications for free!!!)

What you need: Data cable, drivers, Motorola PST, QPST, P2k seems, RSD Lite 3.2, Bell firmware, the Ampd mobile MONSTER FILE!, MMS Package, and the additional files package.(Most of this can be downloaded from the following website. All else can be found by doing a simple google search. and

Flashing the phone to Amp’d:

1) Open RSD lite and go to…….(browse). Find your unzipped Amp’d mobile monster file and click open

2) Make sure your phone is connected securely, fully charged, and has a full charge. Click start

3) Wait for it to say “flash success!” and then disconnect the phone.

4) Give the phone some time to restart. Do NOT pull out the battery

5) Re-start the phone and make sure everything works.

Flashing the phone to Bell:

1) Follow the steps from the flashing to Amp’d to flash to Bell, only use the unzipped bell firmware as opposed to the Amp’d

Getting your phone working properly with the new software ( this is copied and pasted directly from the above website. All credit is owed to the creators of that website.)

Load Seems

P2Kseem4v710

• Create a folder to backup your existing seems

• Open Motorola PST and minimize it

• Connect your phone to the computer

The computer will detect a "USB Composite Device" and several other virtual devices.

• Double click the P2KSEEM.EXE from the folder you extracted the files to earlier.

P2KSeem for V710 should say "connected" in the lower left.

[pic]

• Type 0000 into the "Bytes" field.

Type 29a0 into the Seem field.

Type 0001 into the Record field.

[pic]

• Click "Load from phone".

• Click "Save to file" and save the seem to the backup folder you created

• Click Load from File and browse to the 29a0_sample.seem in the Bell_E815_MMS folder

• Replace the x's with your 10 digit phone number, making sure to skip a space between digits

Use the arrow key, not the space bar.

[pic]

• Click "Save to phone"

• The procedure for the rest of the seems in the Bell_E815_MMS is a litte simpler:

o Type the number in the Seem field

o "Load from phone"

o "Save to file" browse to your backup folder and save.

o "Load from file" browse to the Bell_E815_MMS folder and load the seem file.

o "Save to phone"

[pic]

Repeat this procedure for each of the following files:

o 2742_0001.seem

o 2997_0001.seem

o 299a_0001.seem

o 299b_0001.seem

o 29a1_0001.seem

o 29a9_0001.seem

o 29ab_0001.seem

o 29b2_0001.seem

o 29b3_0001.seem

o 29b6_0001.seem

o 29ba_0001.seem

o 29bb_0001.seem

o 29bc_0001.seem

o 29be_0001.seem

That's it for seems. Close p2kseem but leave Motorola PST open for the next step.

Load WebSessions

• In Motorola PST Click "File" --> "Open RTT 1xBrowser", browse to the Bell_E815_MMS folder and load the "VZW_MMS.rtb" file.

[pic]

• Click on the 6.x tab

• Click on the Proxy 2 Tab.

• Replace "MIN" under username with your 10 digit phone number.

• Click on the "Write to phone button"

[pic]

• Close the Browser file but leave PST open for the next step

Flex Phone

• In Motorola PST Click "File" --> "Open pFlex", browse to the Bell_E815_Files folder and load the "Create_dir_scarlet.hs" file.

[pic]

[pic]

• Click "RUN"

[pic]

[pic]

[pic]

• You're done with P2K mode! Close PST and reboot your phone

Load Files

This portion of the tutorial uses QPST which means we want the phone to be detected as a "Motorola USB Modem". If it is not unplug it from the computer. Turn it off and back on and plug it in again. If you have trouble with QPST go here

• Open QPST Configuration

• Highlight Your Phone

[pic]

• Click "Start CLient" --> "EFS Explorer"

[pic]

[pic]

• Browse the phone's filesystem in QPST and drag the following items into place on the phone.

o Bell_E815_Files\brew\appdb\j2me.settings TO /brew/appdb/ (possibly overwriting an empty file)

o Bell_E815_Files\brew\en\jeodeken.bar TO /brew/en/

o Bell_E815_Files\brew\en\jeodekfr.bar TO /brew/fr/

o Bell_E815_Files\motorola\system\mma_ucp TO /motorola/system/ (overwriting the existing file)

o Bell_E815_Files\motorola\system\mma_dcp TO /motorola/system/ (overwriting the existing file)

o Bell_E815_Files\motorola\shared\jeodek\* TO /motorola/shared/jeodek/

o Bell_E815_Files\motorola\shared\jeodek\skins\moto\* TO /motorola/shared/jeodek/skins/moto/

o Bell_E815_Files\motorola\shared\jeodek\skins\techno\* TO /motorola/shared/jeodek/skins/techno/

Tweaking Settings to make MMS work

Navigate on your phone to MESSAGE CENTER==>MESSAGE SETTINGS==>PIX MESSAGE SETUP==>SERVER INFO==>VZW then MENU==>EDIT

Service Name should be VZW

Server Name should be

Web Session Shoud be VZW_MMS

Now mms should work.

Adding Java Apps



................
................

In order to avoid copyright disputes, this page is only a partial summary.

Google Online Preview   Download