DSM Engineering Plastic Products, Inc
DATA SHEET | |
|KETRON® PEEK - 1030 |
|COMPRESSION MOLDED 30% CARBON REINFORCED POLYETHERETHER KETONE |
|Property |Units |Test |Typical Average |
| | |Method |Values |
| Mechanical | | | |
|Specific Gravity, 73° F |- |ASTM D792 |1.42 |
|Tensile Strength, 73° F |psi |ASTM D638 |14,000 |
|Tensile Modulus of Elasticity, 73° F |psi |ASTM D638 |800,000 |
|Tensile Elongation (at break), 73° F |% |ASTM D638 |2.0 |
|Flexural Strength, 73° F |psi |ASTM D790 |30,000 |
|Flexural Modulus of Elasticity, 73° F |psi |ASTM D790 |1,300,000 |
|Shear Strength, 73° F |psi |ASTM D732 |11,000 |
|Compressive Strength, 10% Deformation, 73° F |psi |ASTM D695 |25,000 |
|Compressive Modulus of Elasticity, 73° F |psi |ASTM D695 |550,000 |
|Hardness, Rockwell, Scale as noted, 73° F |- |ASTM D785 |M97 (125) |
|Hardness, Durometer, Shore "D" Scale, 73° F |- |ASTM D2240 |D86 |
|Izod Impact (notched), 73° F |ft.lb./in. |ASTM D 256Type "A" |1.4 |
|Coefficient of Friction (Dry vs. Steel) Dynamic |- |PTM 55007 |0.24 |
|Limiting PV (with 4:1 safety factor applied) |ft.lbs.in.2 min. |PTM 55007 |41,000 |
|Wear Factor "k" x 10-10 |in.3-min/ft. lbs. hr. |PTM 55010 |160 |
| Thermal | | | |
|Coefficient of Linear Thermal Expansion |in./in./°F |ASTM E-831 (TMA) |1.70 x 10-5 |
|(-40°F to 300°F) | | | |
|Heat Deflection Temperature 264 psi |°F |ASTM D648 |450 |
|Tg-Glass Transition (amorphous) |°F |ASTM D3418 |N/A |
|Melting Point (crystalline) peak |°F |ASTM D3418 |644 |
|Continuous Service Temperature in Air (Max.)(1) |°F |- |480 |
|Thermal Conductivity |BTU in./(hr.ft.2 °F) |- |6.37 |
| Electrical | | | |
|Dielectric Strength, Short Term |Volts/mil |ASTM D 149 |- |
|Surface Resistivity |ohm/square |EOS/ESD S11.11 | ................
................
In order to avoid copyright disputes, this page is only a partial summary.
To fulfill the demand for quickly locating and searching documents.
It is intelligent file search solution for home and business.
Related download
- mechanics of materials review missouri s t
- pe review winter 1997
- volume to weight conversion factors
- water bucket problem calculus physics problem 1
- nupoc study guide
- motor drive system assessment
- gear ratios torque
- dsm engineering plastic products inc
- treeo center university of florida
- weight of cellulose insulation blown in over
Related searches
- products made from plastic bottles
- plastic products company
- plastic products inc phoenix az
- advanced educational products inc bankruptcy
- advanced educational products inc buffalo
- products made from plastic bags
- civil engineering consultants inc indiana
- applied engineering products radiall
- engineering services products company
- applied engineering products aep
- applied engineering products chino ca
- applied engineering products ct